Search Results

Search found 21463 results on 859 pages for 'broken link'.

Page 216/859 | < Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >

  • secure synchronization of large amount of data

    - by goncalopp
    I need to automatically mirror a large amount (terabytes) of files in two unix machines over a slow link (1 Mbps). This needs to be done frequently, but the data doesn't change too much (delta transmission doesn't saturate the link). The usual solution would be rsync, but there's an additional requirement: it's undesirable, from a security standpoint, that either the source or destination machines have (keyless) ssh keys to each other, or any kind of filesystem access. All communication between the two machines should thus be initialized (and mediated) through a third machine. I've asked a separate question about rsync in particular here. Are there other obvious solutions I'm missing?

    Read the article

  • How to make a disk image and restore from it later?

    - by Torben Gundtofte-Bruun
    I'm a new Linux user. I've reinstalled my Wubi from scratch at least ten times the last few weeks because while getting the system up and running (drivers, resolution, etc.) I've broken something (X, grub, unknowns) and I can't get it back to work. Especially for a newbie like me, it's easier (and much faster) to just reinstall the whole shebang than try to troubleshoot several layers of failed "fixing" attempts. Coming from Windows, I expect that there is some "disk image" utility that I can run to make a snapshot of my Linux install (and of the boot partition!!) before I meddle with stuff. Then, after I've foobar'ed my machine, I would somehow restore my machine back to that working snapshot. What's the Linux equivalent of Windows disk imagers like Acronis True Image or Norton Ghost? Note: I found a similar question here.

    Read the article

  • Guacamole on KVM

    - by Siem Hermans
    I currently run a deployment where I provide virtual machines to circa 25 users through ESXi over the VMWare WSX web portal. This works, no doubt about it, it is fast, stable and reliable enough for the end users. However I stumbled across the Guacamole project (Link: http://guac-dev.org/) and the KVM project (Link: http://www.linux-kvm.org/). I must say I am no genius when it comes to Linux but I am interested in replacing the ESXi and WSX combination with a Guacamole and KVM deployment. I have seen people across the internet use ESXi in combination with Guacamole (mostly prior to the release of WSX), but I have yet to see someone use it in conjunction with KVM. Considering my amount of knowledge on Linux in general I would like to ask: Is it possible at all to combine the two?

    Read the article

  • Cannot connect remote mysql, Cpanel?

    - by BerkErarslan
    I use centos and cpanel I need to use remote mysql with php. I add the ip which I try connect to server to "Remote Database Access Hosts" on Cpanel. However, when I try to connect server with this code: <?php $link = mysql_connect("server_ip", "xxx", "xxx") or die(mysql_error()); $db = mysql_select_db("xxx", $link) or die (mysql_error()); print_r($db); I have error like this: Warning: mysql_connect() [function.mysql-connect]: Can't connect to MySQL server on 'xxxx' (10060) in C:\AppServ\www\test.php on line 3 Can't connect to MySQL server on '94.138.204.234' (10060) I also try to connect using "server_ip:3306" but it still doesn't work. How Can I solve this problem ?

    Read the article

  • Sending Emails via Google SMTP - after some time quit working

    - by Chris
    on a website I use PHPMailer to send automated registration emails, etc and also a newsletter-tool (which loops through the emails and sends them one by one). Also, I configured in Gmail under Settings and confirmed @mydomain addresses, so I can send from @mydomain emails without the gmail address being displayed. Furthermore I authorized the website to send mails with this link: https://accounts.google.com/DisplayUnlockCaptcha Now, after 2 month where everything worked perfectly fine, suddenly users started not to receive emails anymore and most recently emails are not even being sent anymore. Also, I received many error messages like this: Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 5.4.1 [email protected]: Recipient address rejected: Access Denied (state 13). When I check at this link: https://toolbox.googleapps.com/apps/checkmx/ It tells 2 none critical errors: Relayhost configuration detected. There SHOULD be a valid SPF record. So, the questions I would have were: does anybody have any hint why it stopped working, what the error messages mean? what to do to fix it? where do I set a SPF record (Cpanel?)? what is a relayhost and how to fix that? It is about 1000-1400 mails a day (gmail's limit is 2000). Also, what can I do wrong when setting up an SPF record? I've heard there are some testing tools for that. Thank you so much already in advance for your help!

    Read the article

  • Muob Package Manager crashes

    - by Woltan
    Clicking on Check for Updates in the kubuntu Muon Package Manager gives the following error message: Unable to download the following packages: Failed to download http://de.archive.ubuntu.com oneiric-updates/universe Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.10 80] Failed to download http://de.archive.ubuntu.com oneiric-updates/multiverse Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.10 80] Failed to download http://de.archive.ubuntu.com oneiric-updates/main i386 Packages 416 Requested Range Not Satisfiable [IP: 141.30.13.10 80] After clicking OK or after just looking at the software sources the package manager crashed with the following error message: The package system could not be initialized, your configuration may be broken. What can I do to fix the problem?

    Read the article

  • Host is unreacheble with static networking configuration via /etc/network/interfaces while GUI NetworkManager is ok

    - by Riccardo
    I have some trouble setting-up the network interface using the static IP configuration. I run ubuntu 12.04 kernel 3.11.0-22 with the back-ports enabled. I followed these instructions from help.ubuntu.com but there seems to exist some conflict between the GUI approach (NetworkManager) and the command line approach. $ sudo nano /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.1.1.50 gateway 10.1.1.10 netmask 255.255.255.0 dns-nameservers 192.168.3.45 192.168.8.10 $ sudo /etc/init.d/networking restart I than try to ping for example google.com ping -c 3 www.google.com the response is that the host is unreachable. The icon on the top right of the desktop says: wired network disconnected. If I work using the GUI approach (Edit Connections and so on...) all works great. Can same one explain to me where I wrong? $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 90:e6:ba:07:4a:77 inet addr:10.1.1.50 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::92e6:baff:fe07:4a77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39619 errors:0 dropped:0 overruns:0 frame:0 TX packets:18520 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19030895 (19.0 MB) TX bytes:2768769 (2.7 MB) $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0

    Read the article

  • Notes for a NetBeans IDE 7.4 HTML5 Screencast

    - by Geertjan
    I'm making a screencast that intends to thoroughly introduce NetBeans IDE 7.4 as a tool for HTML, JavaScript, and CSS developers. Here's the current outline, additions and other suggestions are welcome. Getting Started Downloading NetBeans IDE for HTML5 and PHP Examining the NetBeans installation directory, especially netbeans.conf Examining the NetBeans user directory Command line options for starting NetBeans IDE Exploring NetBeans IDE Menus and toolbars Versioning tools Options Window Go through whole Options window Change look and feels Adding themes Syntax coloring Code templates Plugin Manager and Plugin Portal Dark Look and Feel Themes Toggle line wrap Emmet HTML Tidy NetBeans Cheat Sheets Creating HTML5 projects From scratch From online template, e.g., Twitter Bootstrap From ZIP file From folder on disk From sample Editing Useful shortcuts Alt-Enter: see the current hints Alt-Shift-DOT/COMMA: expand selection (CTRL instead of Alt on Mac) Ctrl-Shift-Up/Down: copy up/down Alt-Shift-Up/Down: move up/down Alt-Insert: generate code (Lorum Ipsum) View menu | Show Non-printable Characters Source menu Show keyboard shortcut card Useful hints Surround with Tag Remove Surrounding Tag Useful code completion Link tag for CSS, show completion Script tag for JavaScript, show completion Create code templates in Options window Useful HTML Palette items Unordered List Link Useful code navigation Navigator Navigate menu Useful project settings Project-level deployment settings CSS Preprocessors (SASS/LESS) Cordova support Useful window management Dragging, minimizing, undocking Ctrl-Shift-Enter: distraction-free mode Alt-Shift Enter: maximization Debugging JavaScript debugger Deploying Embedded browser Responsive design Inspect in NetBeans mode Chrome browser with NetBeans plugin Android and iOS browsers Cordova makes native packages On device debugging On device styling Documentation PHP and HTML5 Learning Trail: https://netbeans.org/kb/trails/php.html Contributing Social Media: Twitter, Facebook, blogs Plugin Portal Planning to complete the above screencast this week, will continue editing this page as more useful features arise in my mind or hopefully in the comments in this blog entry!

    Read the article

  • How to render 2D particles as fluid?

    - by luke
    Suppose you have a nice way to move your 2D particles in order to simulate a fluid (like water). Any ideas on how to render it? This is for a 2D game, where the perspective is from the side, like this. The water will be contained in boxes that can be broken in order to let it fall down and interact with other objects. The simplest way that comes to my mind is to use a small image for each particle. I am interested in hearing more ways of rendering water.

    Read the article

  • Network and Storage Devices Throughput Chart

    - by zroiy
    With all of the different storage and network devices that surround our day to day life, understanding these devices data transfer speeds can be somewhat confusing. Think about trying to identify your weakest link in the a chain that starts with an external USB hard drive (or a flash drive) that's connected to a 802.11g wifi router, can you quickly come up with an answer of where's the bottle neck in that chain , is it the router or the storage devices ? . Well, the following chart should give you an idea understanding different devices, protocols and interfaces maximum throughput speeds. Though these numbers can fluctuate (mostly for worse, but sometimes for the better) due to different kind of factors such as OS overhead (or caching and optimization) , multiple users or processes and so on , the chart can still serve to provide basic information on the theoretical throughput different devices and protocols can get to.. Enjoy.  Link to the full size chart   References:http://en.wikipedia.org/wiki/Sata#SATA_revision_1.0_.28SATA_1.5_Gbit.2Fs.29http://en.wikipedia.org/wiki/Usbhttp://en.wikipedia.org/wiki/Usb_3http://en.wikipedia.org/wiki/802.11http://mashable.com/2011/09/21/fastest-download-speeds-infographic/http://en.wikipedia.org/wiki/Thunderbolt_(interface)http://www.computerworld.com/s/article/9220434/Thunderbolt_vs._SuperSpeed_USB_3.0  Icons:http://openiconlibrary.sourceforge.net/gallery2/?./Icons/devices/drive-harddisk-3.png      

    Read the article

  • Google-Chrome 10 stable crash on every page

    - by Achu
    I installed google-chrome today, when i open any page including askubuntu i got this error message. i see my memory usage is normal(Memory 56% and swap 4.8%) also I reload and i go to another page same problem What is the problem? the last dmesg output [26612.341865] lo: Disabled Privacy Extensions [29651.852476] chrome[15472] general protection ip:1528e26 sp:7fff514a9dc0 error:0 in chrome[400000+3082000] [31447.190586] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=15939 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31451.250190] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16180 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31454.260150] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16322 PROTO=UDP SPT=4243 DPT=161 LEN=49 [31458.648164] [UFW BLOCK] IN=eth1 OUT= MAC=00:1c:25:a1:e7:67:00:16:3e:28:5a:b7:08:00 SRC=172.23.100.6 DST=172.23.20.128 LEN=69 TOS=0x00 PREC=0x00 TTL=128 ID=16513 PROTO=UDP SPT=4243 DPT=161 LEN=49 [33124.300112] lo: Disabled Privacy Extensions [33601.021406] Skipping EDID probe due to cached edid [34594.043501] chrome[15746]: segfault at 0 ip 0000000000d5cdd0 sp 00007fff5149ec20 error 6 in chrome[400000+3082000] [34597.395334] chrome[18112] general protection ip:17c85bf sp:7fff514aa4f0 error:0 in chrome[400000+3082000] [34616.786643] chrome[18124]: segfault at 1007 ip 00000000017c849f sp 00007fff514aabd0 error 4 in chrome[400000+3082000] [37277.436207] lo: Disabled Privacy Extensions [38549.501390] e1000e: eth1 NIC Link is Down [38551.122253] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [38551.122263] e1000e 0000:00:19.0: eth1: 10/100 speed: disabling TSO

    Read the article

  • Could anyone help me get my NETGEAR WNA3100 (Broadcom BCM43231) wireless adapter to work?

    - by Matthew Carroll
    I have just moved back to Ubuntu from Windows 7 and a few months ago, I bought a NETGEAR WNA3100 wireless adapter because my old adapter had broken. I plugged in my adapter and it doesn't seem to work, I also used the windows 7 drivers for it and tried them on the program "Windows Wireless Drivers" and they don't seem to recognize the device. However I have heard you need XP drivers but I can't seem to find them on the internet nor find them on the CD. Could anyone help me get my wireless adapter to work? Any help is greatly appreciate. P.S I do have internet connection though I have to tether my phone to my computer and then connect my phone to my router.

    Read the article

  • Unable to install any packages due to unrecoverable fatal error /var/lib/dpkg/diversions

    - by gforces
    I am currently unable to install any packages. I receive the following error: dpkg: unrecoverable fatal error, aborting: too-long line or missing newline in `/var/lib/dpkg/diversions I have tried various approaches: sudo dpkg --configure -a sudo apt-get clean sudo dpkg-divert --list sudo apt-get check sudo apt-get install -f etc. but all to no avail. Either the output was apparently normal or the error above was thrown. I'm stumped as to how to proceed and would appreciate any assistance. If any further info is required just ask. Thanks for the reply. I followed the suggestions and am now getting a different error: (Reading database ... 50%dpkg: unrecoverable fatal error, aborting: files list file for package 'libksane0' is missing final newline E: Sub-process /usr/bin/dpkg returned an error code (2) Here is the link for the current diversions: http://paste.ubuntu.com/823500/ and the old broken one: http://paste.ubuntu.com/823502/ I tried to reinstall libksane0 but the same error occurred.

    Read the article

  • Connecting to localhost resolves 127.0.0.1 but connects with external IP [Linux, Debian]

    - by skgsergio
    I'm having a problem with a dedicated server, I don't known if it's the default behavior but this is the problem: If I connect to a service located on the server with localhost the service gets as source IP the external IP. Let me show an example, I use netcat for listening on 127.0.0.1:4444 xxxxxx # nc -vv -l -s 127.0.0.1 -p 4444 listening on [127.0.0.1] 4444 ... Lets check if it's ok: xxxxxx ~ # netstat -atnp | grep 4444 tcp 0 0 127.0.0.1:4444 0.0.0.0:* LISTEN 14038/nc Ok lets connect: xxxxxx ~ # nc -vv 127.0.0.1 4444 localhost [127.0.0.1] 4444 (?) open Return to the tty that have the listening process and I get this: connect to [127.0.0.1] from xxxxxx.net [176.31.xxx.xx] 50354 So that's the problem. I have a server daemon that have to listen on localhost and checks that the ip is 127.0.0.1 when the client connects but for some reason when I connect to localhost it reports the external ip... If I do the same with IPv6 it works as excepted... Detects connection as localhost (::1). Some info that can be useful: "localhost" resolves without problems to 127.0.0.1 xxxxxx ~ # ping -c1 localhost PING localhost (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost (127.0.0.1): icmp_req=1 ttl=64 time=0.086 ms Nothing weird on my hosts file, I think... xxxxxx ~ # grep -v ^# /etc/hosts 127.0.0.1 localhost localhost.localdomain 176.31.xxx.xx xxxxxx.net ns1.xxxxxx.net ::1 ip6-localhost ip6-loopback feo0::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts And ifconfig reports all ok... eth0 Link encap:Ethernet HWaddr e0:69:95:d8:30:a1 inet addr:176.31.xxx.xx Bcast:176.31.108.255 Mask:255.255.255.0 inet6 addr: 2001:41d0:8:xxxx::/64 Scope:Global inet6 addr: 2001:41d0:8:xxxx:x:xx:xx:xx/64 Scope:Global inet6 addr: fe80::e269:95ff:fed8:30a1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16916 errors:0 dropped:0 overruns:0 frame:0 TX packets:16914 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8410679 (8.0 MiB) TX bytes:10539881 (10.0 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5570 errors:0 dropped:0 overruns:0 frame:0 TX packets:5570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:744490 (727.0 KiB) TX bytes:744490 (727.0 KiB)

    Read the article

  • Read Wall Street Journal for free using Google Search

    - by Gopinath
    Wall Street Journal publishes very informative articles and most of them are available for paid subscribers. But it is very easy to defeat the pay wall of Wall Street Journal and read the articles for free with the help of Google. The trick is to Google for Wall Street Journal article and click the link displayed on search results to read the article for free. It’s very simple and easy if you are using Google Chrome browser, but it should be straight forward in Firefox and Internet Explorer. Here is a walk through of unlocking today’s Wall Street Journal paid article   1. When you are on online.wsj.com, select the title of subscribers only article you want to read 2. Right on the selected title and choose the option Search Google for “<article title>” 3. Locate the WSJ article on Google search results and click on the article link   4. Boom! You got full access to the article and enjoy reading it for free.   I’ve been using this trick for a while from US to access WSJ articles for free. Most likely this should work for users located outside USA as well.

    Read the article

  • Ubuntu One Bookmark sync not working.

    - by Rob
    Everything in Ubuntu One sync works great except bookmark sync. I tried the wiki answer that said to run: killall beam.smp beam rm ~/.config/desktop-couch/desktop-couchdb.ini dbus-send --session --dest=org.desktopcouch.CouchDB --print-reply --type=method_call / org.desktopcouch.CouchDB.getPort This is what my terminal came back with: robin@robin-MIDWAY:~$ killall beam.smp beam beam: no process found robin@robin-MIDWAY:~$ rm ~/.config/desktop-couch/desktop-couchdb.ini rm: cannot remove `/home/robin/.config/desktop-couch/desktop-couchdb.ini': No such file or directory robin@robin-MIDWAY:~$ dbus-send --session --dest=org.desktopcouch.CouchDB --print-reply --type=method_call / org.desktopcouch.CouchDB.getPort Error org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. robin@robin-MIDWAY:~$ I'm a computer "newbie" so it's possible I'm doing something wrong, are there any tutorials out there on how to use the CouchDB? I have Bindwood installed.

    Read the article

  • Help installing wine

    - by Carter
    The following packages have unmet dependencies: wine1.5 : Depends: wine1.5-i386 (= 1.5.16-0ubuntu1) but it is not installable Recommends: gnome-exe-thumbnailer but it is not going to be installed or kde-runtime but it is not going to be installed Recommends: ttf-droid Recommends: ttf-mscorefonts-installer but it is not going to be installed Recommends: ttf-umefont but it is not going to be installed Recommends: ttf-unfonts-core but it is not going to be installed Recommends: winbind but it is not going to be installed Recommends: winetricks but it is not going to be installed E: Unable to correct problems, you have held broken packages. I get this error when trying to install wine. Please help!

    Read the article

  • Install packages with unmet dependencies

    - by Alvin Sim
    Hi all, I am trying to install some applications but some of them fail to install. The three applications I tried are Vim, Emacs and GNOME-Do. I am using Ubuntu 10.10 installed as a guest OS in VirtualBox. The kernel version installed is 2.6.35-26. The error I got is : alvinsim@ubuntu:/etc/apt$ sudo apt-get install emacs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: emacs : Depends: emacs23 or emacs23-lucid but it is not going to be installed emacs23-nox but it is not going to be installed E: Broken packages What is wrong and how do I fix this? Thanks.

    Read the article

  • Gnome Shell got removed after updating Ubuntu 12.04

    - by CMG
    Now when i try to install it...it shows the following error sudo apt-get install gnome-shell Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: gnome-shell : Depends: libgcr-3-1 (>= 3.4.0) but 3.2.2-2ubuntu4 is to be installed Depends: gir1.2-gcr-3 but it is not installable Recommends: gnome-contacts but it is not going to be installed E: Unable to correct problems, you have held broken packages. How can I install GNOME-Shell?

    Read the article

  • Unable to connect to mysql through JDBC connector through Tomcat or externally.

    - by iftrue
    I've installed a stock mysql 5.5 installation, and while I can connect to the mysql service via the mysql command, and the service seems to be running, I cannot connect to it through spring+tomcat or from an external jdbc connector. I'm using the following URL: jdbc:mysql://myserver.com:myport/mydb with proper username/password, but I receive the following message: server.com: Communications link failure The last packet sent successfully to the server was 0 milliseconds ago. the driver has not received any packets from the server. and tomcat throws: com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: Communications link failure The last packet sent successfully to the server was 0 milliseconds ago. The driver has not received any packets from the server. sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57) Which seems to be the same issue as if I try to connect externally.

    Read the article

  • prevent filesystem from entering read-only mode

    - by user788171
    I have found that my server's filesystem is continuously entering read-only mode. There have been some issues with the raid1 array, but I have removed the bad disk from the array. However, it is still physically plugged into the system because I haven't had a chance to go over to the datacentre, I suspect udev and the system kernel is still picking up the bad disk and throwing errors. In /var/log/messages, there are errors like this: Mar 2 06:53:14 nocloud kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen Mar 2 06:53:14 nocloud kernel: ata1: irq_stat 0x00400040, connection status changed Mar 2 06:53:14 nocloud kernel: ata1: SError: { PHYRdyChg DevExch } Mar 2 06:53:14 nocloud kernel: ata1: hard resetting link Mar 2 06:53:20 nocloud kernel: ata1: link is slow to respond, please be patient (ready=0) Mar 2 06:53:21 nocloud kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 2 06:53:21 nocloud kernel: ata1.00: configured for UDMA/133 Mar 2 06:53:21 nocloud kernel: ata1: EH complete This happens fairly randomly throughout the day until eventually the filesystem becomes read-only. When this happens, my system becomes non-operational which kind of defeats the purpose of having a raid1. Note, ata1 is the bad disk (I think ata1 corresponds to /dev/sda because they are both first in line). Under mdadm, /dev/sda1,2 is no longer being used, but I can't prevent the system kernel from continuing to query that disk when I am no longer using it and throwing these errors. Is there a way to prevent my filesystem from automatically going into read-only mode? Furthermore, is it safe to do so? Thanks in advance. EDIT: Additional information: output from cat /proc/mdstat md1 : active raid1 sdb2[1] 976554876 blocks super 1.1 [2/1] [_U] bitmap: 5/8 pages [20KB], 65536KB chunk md0 : active raid1 sdb1[1] 204788 blocks super 1.0 [2/1] [_U] Output from mount: /dev/mapper/VolGroup-LogVol00 on / type ext4 (rw,noatime) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw,rootcontext="system_u:object_r:tmpfs_t:s0") /dev/md0 on /boot type ext4 (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) EDIT2: pvdisplay output: --- Physical volume --- PV Name /dev/md1 VG Name VolGroup PV Size 931.32 GiB / not usable 2.87 MiB Allocatable yes (but full) PE Size 16.00 MiB Total PE 59604 Free PE 0 Allocated PE 59604

    Read the article

  • Trying to install Team viewer on Ubuntu 12.04

    - by Teknikk
    I recently got Ubuntu installed on my server, I wanted to install TeamViewer so i could easy manage the virtual machines, However, I get errors when installing it from App store?, And I also get errors, but more detailed on the terminal. Error output: tek@tek-G53SW:~/Download$ sudo dpkg -i ipts teamviewer_linux_x64.deb dpkg: error processing ipts (--install): cannot access archive: No such file or directory (Reading database ... 142115 files and directories currently installed.) Preparing to replace teamviewer7 7.0.9360 (using teamviewer_linux_x64.deb) ... Unpacking replacement teamviewer7 ... dpkg: dependency problems prevent configuration of teamviewer7: teamviewer7 depends on libc6-i386 (>= 2.7); however: Package libc6-i386 is not installed. teamviewer7 depends on lib32asound2; however: Package lib32asound2 is not installed. teamviewer7 depends on lib32z1; however: Package lib32z1 is not installed. teamviewer7 depends on ia32-libs; however: Package ia32-libs is not installed. dpkg: error processing teamviewer7 (--install): dependency problems - leaving unconfigured Errors were encountered while processing: ipts teamviewer7 I tried to install it manually, but with no luck, I heard some others has this problems. I am running Ubuntu 12.04 x64. Error @ sudo apt-get install libc6-i386 lib32asound2 lib32z1 ia32-libs : tek@tek-G53SW:~/Download$ sudo apt-get install libc6-i386 lib32asound2 lib32z1 ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-multiarch E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). tek@tek-G53SW:~/Download$ More errors tek@tek-G53SW:~/Download$ sudo apt-get -f install [sudo] password for tek: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages will be REMOVED: teamviewer7 0 upgraded, 0 newly installed, 1 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 81.9 MB disk space will be freed. Do you want to continue [Y/n]? y (Reading database ... 142441 files and directories currently installed.) Removing teamviewer7 ... tek@tek-G53SW:~/Download$ sudo apt-get install libc6-i386 lib32asound2 lib32z1 ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done lib32z1 is already the newest version. libc6-i386 is already the newest version. lib32asound2 is already the newest version. Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-multiarch E: Unable to correct problems, you have held broken packages. tek@tek-G53SW:~/Download$ sudo apt-get install ia32-libs-multiarch Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs-multiarch:i386 : Depends: gstreamer0.10-plugins-good:i386 but it is not going to be installed Depends: gtk2-engines:i386 but it is not going to be installed Depends: gtk2-engines-murrine:i386 but it is not going to be installed Depends: gtk2-engines-pixbuf:i386 but it is not going to be installed Depends: gtk2-engines-oxygen:i386 but it is not going to be installed Depends: ibus-gtk:i386 but it is not going to be installed Depends: libcanberra-gtk-module:i386 but it is not going to be installed Depends: libcups2:i386 but it is not going to be installed Depends: libcupsimage2:i386 but it is not going to be installed Depends: libfontconfig1:i386 but it is not going to be installed Depends: libgail-common:i386 but it is not going to be installed Depends: libgphoto2-2:i386 but it is not going to be installed Depends: libgtk2.0-0:i386 but it is not going to be installed Depends: libnss3:i386 but it is not going to be installed Depends: libqt4-opengl:i386 but it is not going to be installed Depends: libqt4-qt3support:i386 but it is not going to be installed Depends: libqt4-scripttools:i386 but it is not going to be installed Depends: libqt4-svg:i386 but it is not going to be installed Depends: libqtgui4:i386 but it is not going to be installed Depends: libqtwebkit4:i386 but it is not going to be installed Depends: librsvg2-common:i386 but it is not going to be installed Depends: libsane:i386 but it is not going to be installed E: Unable to correct problems, you have held broken packages. tek@tek-G53SW:~/Download$

    Read the article

  • How to set which application is launched by xdg-open?

    - by Dima
    I have run update-alternatives as well as gnome preffered apps selection thing. And all point to have chromium browser as default. Yet when I run xdg-open http://askubuntu.com firefox is launched! Similarly emacs and bzr also launch stuff in firefox instead of chromium. Are there any additional settings which affect xdg-open functionality? Something is definatly broken: UPDATE I have purged firefox: update-alternatives - uses chromium browser sensible-browser - opens chromium browser xdg-open & gnome-open - opens using google-chrome which kindly tells me "it's not default browser" !!!!

    Read the article

  • Compile latest blender on ubuntu 12.0464bit?

    - by gabriel
    What i want is to compile latest blender from SVN. I am using this guide My issues are: How can i install it with the final .deb created file and how can i give this package to a ppa! So, when i execute sudo apt-get update; sudo apt-get install subversion build-essential gettext \ libxi-dev libsndfile1-dev \ libpng12-dev libfftw3-dev \ libopenexr-dev libopenjpeg-dev \ libopenal-dev libalut-dev libvorbis-dev \ libglu1-mesa-dev libsdl1.2-dev libfreetype6-dev \ libtiff4-dev libavdevice-dev \ libavformat-dev libavutil-dev libavcodec-dev libjack-dev \ libswscale-dev libx264-dev libmp3lame-dev python3.2-dev \ libspnav-dev it gives me this The following packages have unmet dependencies: libjack-dev : Depends: libjack0 (= 1:0.121.0+svn4538-3ubuntu1) but it is not going to be installed E: Unable to correct problems, you have held broken packages. I know that skype does not allow the installation of those libraries. Thanks

    Read the article

  • How to work with Firefox nightly build [minefield]

    - by anirudha
    Most of developer love Firefox for their plugin who support for making development easier and faster. many of us use Firefox nightly build aka minefield who update daily. there is a little problem in minefield that there is less plugin on addons site of mozilla for Firefox nightly [minefield]. a solution for this problem is that you need to install the plugin who you want in nightly build from the developer site instead of add-ons site of Mozilla. the reason for that is all many of popular plugin in development for support Firefox 4. How to install follow the thing as mine : go to minefield > addons or toolbar  > addons you see a list of plugin who is not suitable for minefield now go to more link of plugin who you want to get work in Firefox 4. When you click their you go to plugin page on addons site of mozilla or maybe redirect you to developer site. if they show you plugin page then go to developer site by click on link more about developer. now you find that on the developer site they give you the same version or maybe new then you found on mozilla addons site. install the plugin and restart the minefield. you see that most of plugin now work.

    Read the article

< Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >