Search Results

Search found 1072 results on 43 pages for 'rubber boots'.

Page 22/43 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  Hello, I recently did a full upgrade of windows 7 on my thinkpad, everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen just before the Windows logo appears, disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this wont boot with battery plugged in is greatly appreciated - i need to take this battery out on the road/trains etc.... Cheers Matt

  Read the article

• windows 7 crash during hibernation

  - by Andrew Fforts

  At times, when I hibernate my Dell Latitude e6400 with Windows 7 (64 bit), the laptop screen goes black as it should, but then it takes several minutes before it powers down. Then, when I attempt to "resume," Windows boots up from a fresh startup, with all my work lost, and tells me that it's recovered from a serious error. What can I do to resolve this problem? Other background info: -I got a new hard drive with plenty of space about a year ago; I only use a small fraction of that space. This sometimes happens when I don't have any programs running at all. If it's relevant, I do have Dropbox and OneDrive running in the background, though. -The problem usually occurs when I hibernate just after I unplug from an external monitor to bring my laptop home, but I believe it happens at other times, too. Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.4 Locale ID: 1033 Additional information about the problem: BCCode: 1000009f BCP1: 0000000000000004 BCP2: 0000000000000258 BCP3: FFFFFA80036DEB50 BCP4: FFFFF80000B9C510 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1

  Read the article

• off-the-shelf HDD in Dell Optiplex 755 - Invalid Replacement - Press F1 when rebooting

  - by Eric Liprandi

  Hi, I recently put an SSD into my work Optiplex 755. Since then, every time the system boots or reboots, I get prompted to hit F1 to continue with a message like HDD replacement is not valid. The system works just fine. What I am gathering from Dell's website is that I left the original drive internally as a data drive. And apparently the Optiplex does not support 2 drives in the configuration we purchased originally and complains. Any suggestions on how to get rid of this message? some suggested the MEBx or whatever from Intel and to turn it off, but I did not succeed earlier. It's not a big deal 80% of the time, but I regularly work from home and occasionally need to fire a reboot and well, you don't get the BIOS screen remotely :) Regards, Eric.

  Read the article

• Computer disappeared from Workgroup

  - by Moayad Mardini

  I've a LAN that has 8 computers running Windows XP and only one (Computer A) running Windows Server 2003. When computer A boots, it shows up in all computers' Workgroups, but after 15-30 minutes, it disappears from the Workgroup in all computers, including itself. However, files can still be transferred from and to A via full path shortcuts and network drive maps still work. I don't know if this has anything to do with the problem or not, but if that particular computer is turned on while the LAN cable is plugged in, it doesn't connect to the network, but it connects if the cable is plugged in after the computer is run. Any tips why this is happening? Thanks.

  Read the article

• Mecer laptop gives me a white screen when I close the screen

  - by Dane Rossenrode

  I'm having a very strange hardware issue with my Mecer m770u laptop with intel i7 quad core, etc... I'm wondering if anyone has had this issue with any other brand/model of laptop, and what I should fix/replace to solve it...? Basically when I close the screen of the laptop, the screen often goes completely white. If I open it slowly and smoothly again, the screen returns to normal. But if I close the screen when the computer is off, and then switch it on, it boots with a white screen, and opening it slowly/smoothly doesn't help. I have to then switch it on and off a few times before it returns to normal. Makes travelling with my laptop really difficult! Any suggestions?

  Read the article

• Restoring a Ubuntu Linux LVM drive

  - by user848106

  Scenario: I have a hard disk with a bootable sda1 partition and an Linux LVM. I seem to have corrupted the MBR? or Grub? not sure. I know it no longer boots and even with boot-repair and a Ubuntu live usb I was able to restore it. Following a "fix" with boot-repair I get "missing operating system" Can't i just reinstall grub or a new menu.lst? Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0007b68f Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM

  Read the article

• Wiping out user and/or root password in embedded linux

  - by TryTryAgain

  We have a security camera system running an embedded linux. It boots with Lilo as a bootloader and has no tty access once booted. I don't know any username either. SSH/22 is open, but I don't think brute force is an option. I have tried all the common tricks to reset a linux user password (boot from the bootloader in single user mode = doesn't happen, still prompts for user login, boot to a live cd = can't access the file system...it's all loop files and other binary, etc etc), but they are all not possible as it is an embedded linux setup the way it is. Any help/suggestions would be appreciated. Thanks

  Read the article

• Restore Windows 7 bootloader after Windows 8 install

  - by JMK

  I have installed Windows 8 onto a partition after Windows 7, and when I turn my PC on, Windows 8 basically loads completely, and then I get the option to choose my OS. If I select Windows 8, I go straight to the lock screen, if I select Windows 7, my computer completely restarts and then boots into 7. I want to use the Windows 7 installation DVD to restore the Windows 7 bootloader using the method described by the How To Geek but I am worried that if I do this, Windows 8 won't boot. Can anybody advise on whether or not this will work, and if not how can I go back to selecting the OS right after the BIOS loads?

  Read the article

• Linux Mint does not start after renaming home directory

  - by RUBY

  I am new to linux and was just trying to rename the only directory in home from rk to rhk. I messed up the whole thing and the settings. Created some new thing named rhk which I can't remember as it got all messed up and Now I am getting nothing after Linux Mint 10(julia) boots up - no start menu, no panel, no taskbar nothing. I tried to work in the recovery mode and got some(downloaded) 216mb of something(in the repair broken packages) hoping that it might help but didn't help. Moreover whenver I have booted in it shows messages like Could not update ICEauthority file /home/rk./.ICEauthority there is a problem with the configuration server. (usr/lib/libconfig24/gconfsanitycheck2 exited with status 256) The panel encountered a problem while loading "OAFIID: GNOME_mintMenu" The panel encountered a problem while loading "OAFIID: GNOME_IndicatorApplet" Naulitis could not create the following reqiured folders: /home/rk/Desktop, /home/rk/. Naulitis Moreover Alt+F2 gives Run application or run with file and nothing seems to be working.

  Read the article

• Multiple LiveCD iso's on a single USB drive

  - by Keck

  I am looking to create a USB flash drive that I can put multiple LiveCD iso's on and select which boots from startup. The ideal candidate supports linux and windows based iso's, and is relatively simple. It also must have some reasonable process for adding and removing iso from the drive/list. Things that I'm not looking for this specific question: UBCD or other swiss-army knife livecd's. The point is to boot any one of multiple CD's, not to boot a (certainly useful) utility CD. Installing a single LiveCD to a USB drive. I'd like to have multiple iso images, selectable at startup. I don't have a specific purpose in mind, possibilties include a single drive with a knoppix variant, ubuntu desktop, UBCD for dos, UBCD4Win, the Offline NT Password Cracker, etc. Flexible and easy to use are the name of the game!

  Read the article

• XP boot timer=> set, but does nothing?

  - by mark

  My PC has XP Pro and the boot.ini file looks like this: [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(2)\windows [operating systems] C:\CMDCONS\BOOTSECT.DAT="Microsoft Windows Recovery Console" /cmdcons multi(0)disk(0)rdisk(0)partition(2)\windows="eXPee Pro" /noexecute=optin /fastdetect Up until about a week ago it would just time-out and boot normally. I haven't made any hardware changes at all. Now, when the system boots it just sits there and waits for me to hit -enter-. I've searched all over for explanations & possible causes, but found nothing which seems to relate. Anyone here have any idea what may have caused the timer to simply quit working like that ? (BTW, the system clock works just as it ever did and keeps time precisely.) Thanks.

  Read the article

• Windows 2012 Server Hyper-V: Cannot see LAN

  - by Samuel

  I have one NIC on the machine loaded XP on the Hyper-V and had chosen the network as virtual switch. No LAN and no internet shows up on the client. Am I missing something? it used to work in 2008-R2. Details: One network card on machine (Qualcomm Atheros AR8131 PIC-E Gigabit Ethernet controller) The virtual machine hard disk is pointing to and existing XP-SP2 hard disk created using VPC 2007 The Virtual machine Network Adapter is setup as Virtual Switch to the real ethernet controller with Enable virtual LAN identification set to 2 (no other virtual machine is created in the system) After the virtual machine boots LAN shows empty in Control Panel Network Connections (this is XP client) and I also cannot access the internet. XP is showing activation prompt but as far as I know it should not disable the network! Virtual network switch is set to External

  Read the article

• How to prevent Microsoft Lync adding startup entry in Windows?

  - by Naresh

  Microsoft lync makes my laptop boot very slowly and if I disable it from startup, the laptop boots fine and quick. However the issue is, if I start lync again, it puts an entry to startup. So I end up disabling again and again before every boot. I try to put my laptop into sleep only as much possible, however there are many times I need to start up. So, please suggest how to do any of the following? How to remove a program from start up, programatically or a windows setting? How to disable Microsoft lync to stop putting an entry into startup?

  Read the article

• Why does NetworkManager take so long to connect to the wireless network?

  - by spoulson

  I have a Dell Mini9 that came with Ubuntu 8.10. Out of the box, Wifi configuration was done under System settings - Network and worked straightforward. Then, after some update patches, NetworkManager was installed to replace this functionality. Initially, it did not carry over my settings and I had to figure out how to redo it. After lots of bumbling with it, it finally works. However, after bootup the NetworkManager icon waits about 2 minutes before even attempting to connect to the wireless network. Then, about a minute later, it connects and I'm on my way. The Mini9 boots up within 30 seconds from SSD, so opening Firefox and then waiting 3+ min for wireless networking is a bit of a pain. Can anything be done?

  Read the article

• Why does NetworkManager take so long to connect to the wireless network?

  - by spoulson

  I have a Dell Mini9 that came with Ubuntu 8.10. Out of the box, Wifi configuration was done under System settings - Network and worked straightforward. Then, after some update patches, NetworkManager was installed to replace this functionality. Initially, it did not carry over my settings and I had to figure out how to redo it. After lots of bumbling with it, it finally works. However, after bootup the NetworkManager icon waits about 2 minutes before even attempting to connect to the wireless network. Then, about a minute later, it connects and I'm on my way. The Mini9 boots up within 30 seconds from SSD, so opening Firefox and then waiting 3+ min for wireless networking is a bit of a pain. Can anything be done?

  Read the article

• My Intel Core i3 frequently shuts down due to "Processor Thermal Trip error"

  - by explorest

  My Desktop PC running Windows 7 on Intel Core i3 dual processor machine started shutting down during the boot process a couple of days ago. I left it alone for about 48 hours and tried again. The boot process informed me about Processor Thermal Trip as being the cause of boot failures and suggested a Windows recovery process. I went through the recovery process which completed without problems. The PC booted normally and Windows 7 worked as expected but after 10 minutes it again tripped and now whenever I start it, it shuts down during the boot process. What should I do next?... is there a boot menu / setup settings that needs to be adjusted to avoid it... Or is there a hardware problem (which seems unlikely as the machine occasionally boots perfectly )?

  Read the article

• ubuntu-10.04-desktop-i386 does not work with HTTP preseed?

  - by netvope

  Installation media: ubuntu-10.04-desktop-i386.iso I tried a lot of different boot parameters, but either the installer ignored the preseed configuration, or it boot itself directly as LiveCD. An example of the boot parameters I've tried: auto url=http://mydomain.com/path/preseed.cfg boot=casper only-ubiquity initrd=/casper/initrd.lz quiet splash -- If I remove only-ubiquity, it boots as a LiveCD. If I remove boot=casper, it won't boot. If I add vga=normal locale=en_US console-setup/layoutcode=us console-setup/ask_detect=false interface=auto, it still can't do automatic install. If I remove auto, it's the same. What is the correct boot parameters for launching such an installation? From the apache log of the server hosting preseed.cfg, I see that the installer has no problems fetching the preseed file. My preseed file is almost identical to the one at https://help.ubuntu.com/10.04/installation-guide/example-preseed.txt. Moreover, I have run debconf-set-selections -c preseed.cfg to ensure that the preseed file is correct.

  Read the article

• scheduled chkdsk on Windows 7 blinking the hard disk light every 5 seconds, what can I do?

  - by Jian Lin

  PG&E (the local electricity company) came and took out the old power meters and put in a new ones by brute force and with no advance notice in our neighborhood, so my computer went down in power. So I went to Windows 7's drive C and schedule a Disk Cleanup (chkdsk) on the next boot up. When it boots up, it says A disk check has been scheduled To skip disk checking, press any key within __ second(s). and then after it shows To skip disk checking, press any key within 1 second(s). it just sits there, with no further message. the hard disc light blinks every 5 seconds. So what is to be done now? I certainly don't want to brute force power off again.

  Read the article

• off-the-shelf HDD in Dell Optiplex 755 - Invalid Replacement - Press F1 when rebooting

  - by Eric Liprandi

  I recently put an SSD into my work Optiplex 755. Since then, every time the system boots or reboots, I get prompted to hit F1 to continue with a message like HDD replacement is not valid. The system works just fine. What I am gathering from Dell's website is that I left the original drive internally as a data drive. And apparently the Optiplex does not support 2 drives in the configuration we purchased originally and complains. Any suggestions on how to get rid of this message? some suggested the MEBx or whatever from Intel and to turn it off, but I did not succeed earlier. It's not a big deal 80% of the time, but I regularly work from home and occasionally need to fire a reboot and well, you don't get the BIOS screen remotely :) Regards, Eric.

  Read the article

• new monitor won't work on win3.1

  - by Rick Workover

  My old system monitor for my Windows 3.1 machine failed and the new flat screen has a sync error. The new monitors do not support the refresh/screen size it is set to. It boots up into Windows and the monitor is blank with a sync error. Without Windows 3.1 working I don't know how to change the refresh/size to get it to work. I haven't used Win3.1 in so long that I can't remember how to fix this. So, how do I reset the refresh rate and screen resolution it is set to, without being able to actually see anything?

  Read the article

• grub error: symbol 'grub_puts_' not found

  - by ladaghini

  I updated from Ubuntu 9.10 to 10.04, and after installation, the computer restarted. When grub loaded, all I get is a screen that says error: symbol 'grub_puts' not found and a useless grub prompt that looks like grub_rescue I've tried reinstalling grub from the livecd (usb drive) following this guide: https://help.ubuntu.com/community/RecoveringUbuntuAfterInstallingWindows to no avail. Sometimes, when I start up from the live usb, linux doesn't recognize the harddrive at all. It's not in the places menu, nor does fdisk list anything. If anyone can help fix up grub so it recognizes and boots up the two os's I have installed, I'd appreciate it. Also, I know little about grub, so try and make it easy to understand.

  Read the article

• EFI Partition Types

  - by Will

  Another employee was working with a mounted VHD and was using diskpart on it and I'm not sure if he messed something up or not. I think it's fine but I wanted to double check. We have a Windows 2008 x64 machine that boots with EFI because of the large disks in the system. What should the different labels be within Disk Manager for this system? Here is what is currently set: 200 MB Partition - EFI System Partition C Partition - Boot, Page File, Crash Dump There should not be an active partition under EFI, correct? Also, is there supposed to be a "System" label in addition to "EFI System Partition"?

  Read the article

• Broadcom BCM5716 Hangs on CentOS 6 Boot

  - by someotherguy

  I have a fresh CentOS 6 installation on a Dell R310 server with a Broadcom BCM5716. The onboard NIC is causing the boot to hang for some reason. Welcome to CentOS Linux Starting udev: udev: starting version 147 Boardcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.23b (Feb 01, 2011) bnx2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 That's it... then it just hangs / freezes. If I disable the NIC via the BIOS settings, CentOS boots fine. I've downloaded and installed the latest driver from Broadcom's website. Any ideas?

  Read the article

• How can I auto-connect to a WPA2 Enterprise network?

  - by Demetri

  I would like my computer to automatically connect to a WPA2-Enterprise network as soon as it boots whenever the network is available, without any action needed by me. The computer already offers to connect, and even remembers the password, but I must still hit 'Enter' to connect. Also, connection does not occur if my login is at the terminal. I would like to automatically connect every time I login, no matter how I do so, unless a more preferred network is available. What is the best way to do this? I am running Fedora 19. A shell script that can be invoked at the terminal would be preferred. Connecting even if the Gnome-desktop has not launched is a must.

  Read the article

• Windows OS's cannot boot on new internal harddrive

  - by Kothari

  I have installed a new internal 500GB hard drive into a Dell Inspiron N4030 and it appears that the installation was entirely successful. The BIOS recognizes the drive and shows the serial number of the hard drive. The problem is that I cannot boot any Windows OS. I have tried XP, Vista, Windows 7 and Windows 8. It displays only a black screen with a blinking cursor. Fedora boots successfully. My old hard drive crashed, but would atleast boot up these OS's before it died. Any help?

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >