Search Results

Search found 10005 results on 401 pages for 'regex trouble'.

Page 220/401 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >

• How to configure remote access to multiple subnets behind a SonicWALL NSA 2400

  - by Kyle Noland

  I have a client that uses a SonicWALL NSA 2400 as their firewall. I need to setup a second LAN subnet for a handful of PC. Management has decided that there should be a second subnet even though intend to allow access across the two subnets - I know... I'm having trouble getting communication across the 2 subnets. I can ping each gateway, but I cannot ping or seem to route traffic fron subnet A to subnet B. Here is my current setup: X0 Interface: LAN zone with IP addres 192.168.1.1 X1 Interface: WAN zone with WAN IP address X2 Interface: LAN zone with IP address 192.168.75.1 I have configured ARP and routes for the secondar subnet (X2) according to this SonicWALL KB article: http://www.sonicwall.com/downloads/supporting_multiple_firewalled_subnets_on_sonicos_enhanced.pdf using "Example 1". At this point I don't minding if I have to throw the SonicWALL GVC software VPN client into the mix to make it work. It feel like I have an Access Rule issue, but for testing I made LAN LAN, WAN LAN and VPN LAN rules wide open with the same results.

  Read the article

• Stunnel too many clients

  - by davidsmalley

  I'm trying to hook up stunnel and haproxy to forward https connections through to some backend servers. I've got haproxy setup right, and I seem to have stunnel set up right. Trouble is that when I hit the setup with a load test after a while I start to see these log entries: 2010.05.05 11:24:43 LOG7[3498:3086792368]: https accepted FD=512 from 10.195.158.225:52579 2010.05.05 11:24:43 LOG4[3498:3086792368]: Connection rejected: too many clients (=500) I guess I've hit a limit somewhere but I wasn't sure how to fix it, there doesn't seem to be a config file option for stunnel to change this. Does anyone know how to configure stunnel for a potentially large number of connections?

  Read the article

• How to create a bootable USB Windows OS using Mac OS X

  - by Ali

  I'm having a trouble here because of my PC infected today and I tried everything to get it back and the only option left for me now is to do a clean install. Now what happen is I have Macbook Pro with 8GB USB which I emptied the USB stick now. I've download Windows 7 from my college website [With license not pirate] and wanted to make a bootable USB so I can format my PC to get it run again. Now I know that disk utilities can be done with DVD/CD but what I can make a bootable USB to run it on my PC?

  Read the article

• Puppet class inheritance confusion

  - by EMiller

  I've read the documentation on scope, but I'm still having trouble working this out. I've got two environments that are very similar - so I've got: modules/django-env/manifests/init.pp class django-env { package { "python26": ensure => installed } # etc ... } import "er.pp" modules/django-env/manifests/er.pp $venvname = "er" $venvpath = "/home/django/virtualenvs" class er { file { "$venvpath/$venvname" : ensure => directory } # etc ... } class er-dev { include er } class er-bce-dev { $venvname = "er-bce" include er } manifests/modules.pp import "django-env" manifests/nodes.pp node default { # etc ... } node 'centos-dev' imports default { include django-env include er-bce-dev include er-dev } The result here is that the "inheritance" works - but only the first "er-" item under the 'centos-dev' node is acted upon, I either get er-bce-dev or er-dev, but not both. There must be some basic thing I'm misunderstanding here. Is it the difference between import and include ? (not sure I understand that)

  Read the article

• How can I efficiently group a large list of URLs by their host name in Perl?

  - by jesper

  I have text file that contains over one million URLs. I have to process this file in order to assign URLs to groups, based on host address: { 'http://www.ex1.com' = ['http://www.ex1.com/...', 'http://www.ex1.com/...', ...], 'http://www.ex2.com' = ['http://www.ex2.com/...', 'http://www.ex2.com/...', ...] } My current basic solution takes about 600 MB of RAM to do this (size of file is about 300 MB). Could you provide some more efficient ways? My current solution simply reads line by line, extracts host address by regex and puts the url into a hash. EDIT Here is my implementation (I've cut off irrelevant things): while($line = <STDIN>) { chomp($line); $line =~ /(http:\/\/.+?)(\/|$)/i; $host = "$1"; push @{$urls{$host}}, $line; } store \%urls, 'out.hash';

  Read the article

• Installing PHP-GTK with PHP 5.3 on OS X

  - by Shabbyrobe

  I'm having trouble getting php-gtk installed with php 5.3 on os x. I'm currently using macports to do it and when I try to install php-gtk, it spews 'duplicate static' errors: Error: Target org.macports.build returned: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_php_php5-gtk/work/php-gtk-2.0.1" && /usr/bin/make -j2 all " returned error 2 Command output: ext/gtk+/gen_pango.c:2951: error: duplicate 'static' ext/gtk+/gen_pango.c:2957: error: duplicate 'static' ext/gtk+/gen_pango.c:3097: error: duplicate 'static' ext/gtk+/gen_pango.c:3103: error: duplicate 'static' Is there a way to coerce it into building, or an alternative way to install it?

  Read the article

• Windows 7 pricing

  - by bwerks

  I'm having trouble wading through Microsoft's marketing information. Does anyone know if Windows 7 x86 to Windows 7 x64 is a valid upgrade path? I know you can't actually use the built-in "upgrade" installation path; this is more of a licensing question. Although that may have answered my own question: is this idea even possible? Or do "upgrade" versions of Windows function only when executed from inside the OS, and not when doing fresh installs? Thanks!

  Read the article

• best data+partition recovery software

  - by Pennf0lio

  I accidentally formatted my Drive D that contained all my Backups and Documents. I separated my files to my Drive D hoping I will not harm my files. Since I use Acronis Recovery to Install a new OS with some pre-installed application to my HDD I didn't realize I also formated/erase my Drive D. Now my drive D is unpartitioned. I am really in really in deep trouble and would need some urgent help, Please recommend a Software that at least can restore my Old Drive that contained my files. I'm assuming most of you think this is a duplicate of some old questions here, But I'm not looking for data recovery, I need to recover the whole partition with the files. I used to use "Recuva" but It only recovers files not the whole folders with the files in it. Please advice. Thank You!

  Read the article

• Trucrypt or any HDD encryption solution with a bypass?

  - by sorrrydoctorforlove

  Hello experts, in my environment here we have started using trucrypt to encrypt and protect our laptops that are being brought out of the office. The issue comes with the password, we can document the passwords and assign them to users but if they simply use the program to change the password, and then forget it we are in trouble. We backup our data to external locations so it should be fine, but is there any way to install a bypass to be able to boot the laptop or stpo users changing their password (while they have local admin access)? Or should we try another solution? thanks.

  Read the article

• Match returning a string instead of object

  - by Pablo

  This simple regex matching returns a string instead of an object on every browser but the latest firefox... text = "language. Filename: My Old School Yard.avi. File description: File size: 701.54 MB. View on Megavideo. Enter this, here:" name = text.match(/(Filename:)(.*) File /); alert(typeof(name)); as far as i know this the match function is suppose to return an object (Array). Has anyone come across this issue?

  Read the article

• What permissions / ownership to set on PHP Sessions Folder when running FastCGI / PHP-FPM (as user "nobody")?

  - by Professor Frink

  I'm having trouble getting a number of scripts running because PHP-FPM can't write to my session folder: "2009/10/01 23:54:07 [error] 17830#0: *24 FastCGI sent in stderr: "PHP Warning: Unknown: open(/var/lib/php/session/sess_cskfq4godj4ka2a637i5lq41o5, O_RDWR) failed: Permission denied (13) in Unknown on line 0 PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/lib/php/session) in Unknown on line 0" while reading upstream" Obviously this is a permission issue; my session folder's owner/group is the webserver's user, NGINX. PHP-FPM runs as nobody though, and hence adding it to the nginx group is not so trivial. A temporary solution is to set the permissions of /var/lib/php/session to 777 - I have a feeling that's not the "best practice" though. What is the best practice when you need to assign a daemon write access to a folder, but it is running as nobody ?

  Read the article

• IP camera's multicast/RTSP conflicting with 2.4GHz Wi-Fi?

  - by jayson

  Here at our business we have a Netgear R7000 running DD-WRT. I have been slowly adding IP cameras which I run using Blue Iris software. The last camera I bought (which is NOT a wireless camera), when I plug it into the network I start having really bad connection issues on the 2.4GHz Wi-Fi network. The 5GHz works fine, just the 2.4GHz all of the sudden has trouble connecting, as if it's conflicting. I've tried playing with the camera settings, different IP addresses, HTTP ports, etc, and discovered it to be a conflict with multicast. When multicast is checked, the Wi-Fi has issues but my video streams via Blue Iris. When unchecked, Wi-Fi works fine but the video won't stream through Blue Iris. The problem is there are no settings in the camera to change the RTSP port, which is set to 34567. Does anyone know something that could fix this issue? It all seems very strange to me but maybe someone has an idea?

  Read the article

• PECL on Mac OS X 10.6

  - by Rowan

  I'm having trouble finding PECL on a Mac OS X 10.6 machine. I'm using the default install of Apache and PHP for development and have installed MongoDB, however I can't work with Mongo/PHP without the mongo PECL extension. Is there a copy of PECL on a Mac or will I have to install it? If so, where is it? If not, do you know of a good tutorial for getting it up-and-running? I've tried the obvious stuff: sudo find / -name "pecl" -print returns nothing Thanks very much

  Read the article

• EC2-like virtualisation platform with non-RDP access

  - by code'

  I'm looking into setting up a few small VMs. The trouble is the software I intend to install on them (Cisco VPN Client) blocks out networking (other than to the target VPN destination...) with no workaround. This means that Remote Desktop or other methods of connecting to VMs that go via the Internet (e.g. GoToMyPC, LogMeIn) are a non-starter. What I'm really looking for is an EC2-like platform but which gives direct access to the VM through (for example) Hyper-V Manager. Sadly the only way they all seem to offer to remote control the VMs is direct access via Remote Desktop, whereas I need to be one layer above that (if that makes sense). A viable alternative would be to run virtualisation software within a Windows EC2 instance; obviously hardware virtualisation is impossible but I wonder if there are any software virtualisation platforms that could be run and that would work. Does anyone know if something like this exists/is possible? Thanks! C

  Read the article

• how to ingore comma when returning json mvc

  - by Darcy

  Hi all, I'm returning JSON from my controller to my view in order to populate a jquery autocomplete textbox in MVC. The problem is, some of my data contains commas, and therefore is split by the autocomplete helper. Heres my code. Controller: public ActionResult GetData() { var data = repository.GetData(); return Json(data); } View (script): $.post("../MyController/GetData", function(data) { var evalData = eval(data) + ""; //formats the text $("#Data").autocomplete(evalData.split(","), { max: 500, matchContains: true }); }); As you can see, I am using the jquery .split helper to split the returned Json. Should I be using regex or should I go with a completely different approach?

  Read the article

• Plus signs appearing in Google searches

  - by emddudley

  Ever since Google implemented their new look at the beginning of May, I have been having trouble with their search engine changing all of the spaces in my query to plus signs. This behavior occurs when I use the search box in both Firefox and Internet Explorer. For example, if I search for google search plus signs I am taken to the following URL, where google+search+plus+signs is in the search box. http://www.google.com/search?q=google+search+plus+signs&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a However if I perform the search from google.com, I get taken to a different URL with google search plus signs as I'd expect: http://www.google.com/#hl=en&source=hp&q=google+search+plus+signs&aq=f&aqi=g1&aql=&oq=&gs_rfai=&fp=d2a3ca21987adb1 Do I need to update my browsers or something?

  Read the article

• Should I reinstall my production server from 32 bit to 64 bit if it has 16GB of RAM?

  - by Alexandru Trandafir Catalin

  I have a production server with 16GB of RAM that came with a 32bit CentOs installation. The website hosted on this server is increasing its traffic every day and I am having some MySQL trouble so I tried to check the MySQL configuration with mysqltuner.pl and gave me the following messages: [!!] Switch to 64-bit OS - MySQL cannot currently use all of your RAM *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** So my question is: can I survive with the 32 bit? Or I will have to install the 64 bit OS? Thanks.

  Read the article

• Windows 7 upgrade licensing

  - by bwerks

  I'm having trouble wading through Microsoft's marketing information. Does anyone know if Windows 7 x86 to Windows 7 x64 is a valid upgrade path? I know you can't actually use the built-in "upgrade" installation path; this is more of a licensing question. Although that may have answered my own question: is this idea even possible? Or do "upgrade" versions of Windows function only when executed from inside the OS, and not when doing fresh installs? Thanks!

  Read the article

• How to require a cell input if another cell has a value

  - by Connor

  I'm trying to edit the VBA for one of my workbooks so that If there is a value in column A, then a value for column C is required or else the file won't save, but i'm having some trouble with this. I can get excel to check a cell for any input and require it have input, but I need it to check if a different cell has an input before requiring input. This is because not all of the lines in my spreadsheet will be used all of the time, but some people forget to put very important pieces of information in the spreadsheet which throws some of our balances off. An SKU is entered on the sheet when we switch to a new one, and I want the program to make sure there is an amount of product in a given cell every time a new SKU is entered onto the sheet. Thanks.

  Read the article

• Remove Live ID authentication from user account

  - by slugster

  I've just run in to a really annoying issue with Windows 8.1 - it seems I cannot remove the need to use Live ID credentials from an account without completely deleting that account. I know the process to do it - use the Disconnect link from the Accounts-Your account screen. The trouble comes when you get to the Switch to a local account screen, it will not let you enter the current account for the user name, instead you must enter a new one thus creating a new user account. Can I revert back to using just a local login without having to recreate the account? It seems quite retarded that I have to recreate the account, as deep down the only change required is which credential provider is used to authenticate the login. (Note that this Live ID linkage was created by using the Windows Store, not as a result of an upgrade from 8 to 8.1).

  Read the article

• Fujitsu siemens V6535 - crash when going standby ?

  - by marc

  Welcome, I trouble with my laptop fujitsu siemens model V6535. My siemens work under Windows 7, and from upgrade time (vista to 7) notice something what make me really angry. When my siemens go to standby mode (when i don't use it for some time), power diode change to red and start blinking (standbay mode). When i push power button (wake up it), blinking diode change to green but nothing else happend (nothing on display, no sound of HDD). When i press power button few second and try turn it on again... it wont display anything... i have unplug charger and then shutdown and power on again without power cable. Then he start working... Few days ago i done upgrade bios to nevest version... but it don't help... Anyone have idea what can be wrong ?

  Read the article

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• How can artificially create a slow query in mysql?

  - by Gray Race

  I'm giving a hands on presentation in a couple weeks. Part of this demo is for basic mysql trouble shooting including use of the slow query log. I've generated a database and installed our app but its a clean database and therefore difficult to generate enough problems. I've tried the following to get queries in the slow query log: Set slow query time to 1 second. Deleted multiple indexes. Stressed the system: stress --cpu 100 --io 100 --vm 2 --vm-bytes 128M --timeout 1m Scripted some basic webpage calls using wget. None of this has generated slow queries. Is there another way of artificially stressing the database to generate problems? I don't have enough skills to write a complex Jmeter or other load generator. I'm hoping perhaps for something built into mysql or another linux trick beyond stress.

  Read the article

• OneNote can't connect to SkyDrive in Windows 8.1

  - by Greg

  Since I installed windows 8.1 I can't open my OneNote notebooks stored on skydrive with the 2013 Office OneNote app. When I click in the office app to open from skydrive it gives back: "We can't get your notebooks right now. Please try again later." I can open them without trouble in the modern UI onenote app, but I can't open password protected pages there. Also if I try to open it from a browser the error message follows: "We couldn't open that location. It might not exist or you might not have permission to open it." Neither can I create new notebooks on skydrive with the office app. "...The specified location is not available. -You do not have permissions to modify the specified location..." Can it be fixed somehow? Or can I at least save a notebook to my hard drive without opening it in office? The backup file got deleted with the win 8.1 installation.

  Read the article

• How can I share a video file during a webinar?

  - by Brien Malone

  Here is the scenario: I have a number of remote employees around the globe. I want to have a video chatting session. No problem there. Halfway through, I want to shut off all camera video feeds and simulcast (synchronous) a training video to my team. How do I do this? We have tried office communicator, but the frame rate was awful and no audio. Adobe Connect had similar trouble. In both cases we were limited by the main office's small internet pipe, but it is clear that video delivered by shared desktop is not a good solution.

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >