Search Results

Search found 8450 results on 338 pages for 'mail gateway'.

Page 225/338 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• got VPN l2l connect between a site & HQ but not traffice using ASA5505 on both ends

  - by vinlata

  Hi, Could anyone see what did I do wrong here? this is one configuration of site1 to HQ on ASA5505, I can get connected but seems like no traffic going (allowed) between them, could it be a NAT issue? any helps would much be appreciated Thanks interface Vlan1 nameif inside security-level 100 ip address 172.30.205.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address pppoe setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! passwd .dIuXDIYzD6RSHz7 encrypted ftp mode passive dns server-group DefaultDNS domain-name errg.net object-group network HQ network-object 172.22.0.0 255.255.0.0 network-object 172.22.0.0 255.255.128.0 network-object 172.22.0.0 255.255.255.128 network-object 172.22.1.0 255.255.255.128 network-object 172.22.1.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_20_cryptomap extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list inside_nat0_outbound extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list policy-nat extended permit ip 172.30.205.0 255.255.255.0 172.22.0.0 255.255.0.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) 172.30.205.0 access-list policy-nat access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute username errgadmin password Os98gTdF8BZ0X2Px encrypted privilege 15 http server enable http 64.42.2.224 255.255.255.240 outside http 172.22.0.0 255.255.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 190 match address outside_20_cryptomap crypto map outside_map 190 set pfs crypto map outside_map 190 set peer 66.7.249.109 crypto map outside_map 190 set transform-set ESP-3DES-SHA crypto map outside_map 190 set phase1-mode aggressive crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 190 crypto isakmp ipsec-over-tcp port 10000 tunnel-group 66.7.249.109 type ipsec-l2l tunnel-group 66.7.249.109 ipsec-attributes pre-shared-key * telnet timeout 5 ssh 172.30.205.0 255.255.255.0 inside ssh 172.22.0.0 255.255.0.0 outside ssh 64.42.2.224 255.255.255.240 outside ssh 172.25.0.0 255.255.128.0 outside ssh timeout 5 console timeout 0 management-access inside vpdn group PPPoEx request dialout pppoe vpdn group PPPoEx localname [email protected] vpdn group PPPoEx ppp authentication pap vpdn username [email protected] password ********* dhcpd address 172.30.205.100-172.30.205.131 inside dhcpd dns 172.22.0.133 68.94.156.1 interface inside dhcpd wins 172.22.0.133 interface inside dhcpd domain errg.net interface inside dhcpd enable inside ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! end

  Read the article

• How to set which IP to use for a HTTP request?

  - by GetFree

  This is probably a silly question. I'm doing some http requests using wget from the command line, and I want those connections to be made through one specific IP of the 4 IPs my server has. Those http requests go to one specific range of IPs so I only want those to be routed differently. The 4 interfaces in my server are eth0, eth0:0, eth0:1, eth0:2. I tried with the following command: route add -net 192.164.10.0/24 dev eth0:0 But when I see the routing table it says: Destination Gateway Genmask Flags MSS Window irtt Iface 192.164.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 The interface is set to eth0 not eth0:0 as my command says. What am I doing wrong?

  Read the article

• Micro Btx Motherboard Replacement.

  - by Judy

  I got the Vundo virus that took out the mobo and hard drive on my Gateway GT5220. Is there a replacement that will work? I'm willing to keep XP. I want to fix it the cheapest way possible. The mobo is a NVIDIA GeForce 6150 AM2 microBTX with primary IDE and 4 SATA connections. I want to use a new SATA as my primary, but would like to be able to connect my old IDE drives to transfer my pictures from them to the new drive. I would appreciate any help. Thanks!

  Read the article

• how to manage credentials/access to multiple ssh servers

  - by geoaxis

  I would like to make a script which can maintain multiple servers via SSH. I want to control the authentication/authorization in such a manner that authentication is done by gateway and any other access is routed through this ssh server to internal services without any further authentication/authorization requirements. So if a user A can log into server_1 for example. He can then ssh to server_2 without any other authentication and do what ever he is allowed to do on server_2 (like shut down mysql, upgrade it and restart it. This could be done via some remote shell script). The problem that I am trying to solve is to come up with a deployment script for a JavaEE system which involves databases and tomcat instances. They need to be shutdown and re-spawned. The requirement is to have a deployment script which has minimal human interaction as possible for both developers and operation.

  Read the article

• TS connection lost but not local

  - by Owl

  I have an office that is connected to a shared db server and terminal services server, that other offices use as well, through a vpn tunnel. For some reason all workstations in the office will lose connectivity to the remote address but will remain connected to their local internet. I have checked both firewalls to ensure all settings match accordingly. They seem to go down at routine times every day and it doesn't last longer than a minute or two. Any ideas of what this may be? OS: Windows Server 2003R2 Terminal Services 5.2 Symantec Gateway 320 & Symantec Firewall/VPN 100

  Read the article

• having 2 ip's on a debian 7 box

  - by David

  I just installed Debian Wheezy on my homeserver. I want to assign 2 ip's to it on the same network interface, 1 static ip (eth0) and 1 dynamic ip (eth0:1). I know it doesn't make much sense but I need it to test something. I edited my /etc/network/interfaces to be like this: auto lo eth0 eth0:1 iface lo inet loopback iface eth0 inet static address 192.168.178.240 network 192.168.178.0 netmask 255.255.255.0 broadcast 192.168.178.255 gateway 192.168.178.1 iface eth0:1 inet dhcp when I bring up eth0:1 (ifup eth0:1) I get the following error (eth0 works fine) Bind socket to interface: No such device Failed to bring up eth0:1. is it even possible to have a dynamic and static ip on the same network adapter?

  Read the article

• How to create a VPN between a Host and VMWare VMs?

  - by Anindya Chatterjee

  I have a set of machines as follows My home laptop running Win7 Ultimate with internet connection. A vmware workstation vm running Windows Server 2003 Standard edition server in my laptop w/o internet connectivity Some of my peers' machines connected to internet I want to create a VPN with these machines, provided the VM will not have any direct internet connection and my peers should able to connect to the SVN server application running on this Win2003 server VM. Can anybody please suggest me how to setup this network, what software I need to install in both physical machine and vm, what kind of network connectivity should be there between vmware guest and host machine? EDIT: I deliberately don't want to connect the VM with internet. The host will work more of a gateway of the VPN connection for the VM.

  Read the article

• How to limit access to Exchange 2003 Mobile Actviesync server by user?

  - by micilin

  So I was asked to set up an Exchange Activesync mobile gateway. That's done. It's a separat eExchange 2003 front-end server configured for SSL, and I've put an off-domain ISA server in front of it. Now I'm being asked to limit which users can connect to it. By default an Exchange front-end server allows any user who has a mail account to connect to the front -end server. So I'm looking at the permissions on the various IIS sites/apps on the server, but I know that it's easy to break Exchange Front-end server perms. So I've got the following in IIS: Exadmin Exchange EchWeb Microsoft-SErver-ActiveSync MobileAdmin OMA And a couple of others that I dont think are relevant. Can I change the permissions on one of these to restrict who can connect to Activesync? As a bonus: Can I do it in a way that does not affect ordinary browser based Exchange Access? Thanks in Advance!!

  Read the article

• VM clients can not access WAN

  - by Saariko

  I have a new VM host on my network, on a Dell R620. The dedicated iDrac is connected with static IP of: 192.168.3.x NIC #1 is connected to my router The eSXI 5.1 host is with IP of 192.168.3.250 The vSphere appliance has a static IP of 192.168.3.241 All the clients on the new host are in the same network 192.168.3.x All clients are Windows 2008 R2 My problem is that non of the clients can access the WAN. I can't ping anything which is beyond my router. I CAN ping anything within my router, even if it's on a different subnet - 192.168.0.x (Router rules are in tact and working) I can ping the gateway (192.168.3.254) One thing that I checked, and is bothering my (but don't know if it has any relevance) is that on the Host Networking properties, there is a vmnic0 (picture) that shows as if it only recognizes 192.168.0.x network - is that so? The command: route print shows me the following details, where I have a duplicate entry for 0.0.0.0 (and one is wrong) - which is probably also why it's not working

  Read the article

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• Using a Dell PowerConnect to set up load balancing/redundancy, 1 switch 2 routres 2 private wan link

  - by MarianoC

  Hi, We have different locations connected by two different WAN providers. Each site has a dell powerConnect 6224 and two cisco routers with the WAN connections (we don’t have access to router admin). The 6224 connects to each cisco LAN port and to our LAN backbone. We would like the 6224 provide the ip gateway address and load balance and support redundancy, if one of the routes fail. Is this possible?. We can't find any samples on doing this and we have tried with no success. Any help or link to documentation regarding this, will be greatly appreciated. Thanks, MarianoC

  Read the article

• Unable to access internet if wireless enabled

  - by balki

  The following is my route output. eth0 is my wired network and eth1 is my wireless network. Only wired one has access to internet. If I enable wireless, I am not able to access internet, it tries to access via eth1 and I get 404 page of the wireless router. Why does eth1 have higher preference though default is eth0 (link)? [balakrishnan@mylap ~]$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.26.0.1 0.0.0.0 UG 0 0 0 eth0 10.26.0.0 * 255.255.192.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 * 255.255.255.0 U 9 0 0 eth1

  Read the article

• New power supply and now HDDs are not recognized

  - by Michael

  So I upgraded to a new X4 ULTRA power supply that was recommended to me by a local TigerDirect store. After installing it along with a new liquid cooling system, I booted it up and it automatically fried my CD Drive. After that I noticed that the OS wouldn't start and figured out that none of the 4 HDDs in my computer were being recognized by the BIOS. I feel them spool at a steady pace and have tried new cables and connections but to no avail. I triple checked all of the connections and cables and have no idea what is wrong. This isn't the first time I changed a PS or CPU cooling system but I am at a dead end. Any ideas, aside from buying a USB HDD reader and seeing if they are all fried? Also, this is a stock Gateway mobo with the mobo USB connections already dead. Could the new PS have fried the SATA connections??

  Read the article

• Remove a known network from Windows 8

  - by Edward Brey

  When Windows 8 detects a network based on the assigned IP address, netmask, default gateway, etc., it remembers the network along with the setting you give it as a public or private network. If you change the configuration of a network (e.g. reconfigure your router), Windows may determine you are on a new network and assign it a name of Network 2 or YourAPN 2. This less-than-friendly name shows up in many places in the Windows 8 UI, but unlike the good old days of Windows 7, there doesn't appear to be any UI to merge or delete these networks. What's the best way to merge or delete networks you don't want?

  Read the article

• A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

  - by user16654

  I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

  Read the article

• Windows 2003 - RAS service - VPN client can only connect to server, not internal network

  - by Gk

  Here is my diagram http://imageshack.us/photo/my-images/263/vpnt.png/ Server has two NIC: One connect to Internet, one connect to internal network. RAS service is configured with static IP pool on the same subnet of internal network (10.10.0.x). The problem is when a client connect to server, client can connect to server(10.10.0.10), but cannot connect to another host locate in internal network (10.10.0.11) even cannot ping to 10.10.0.50. RAS configured with IP routing enabled, client connect with options: Use default gateway on remote network. I'm messed up and can not figure out what wrong. Please help me T_T. TIA, giobuon

  Read the article

• ubuntu server in a vm, can't connect to internet

  - by jessh

  I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

  Read the article

• How to elegantly selectively exclude FreeBSD network traffic from OpenVPN interface by port

  - by Polygonica

  inexperienced sysadmin here. I'm planning on running a net daemon inside a FreeBSD jail through OpenVPN, but want to be able to SSH directly into the jail and use the daemon's web interface daemon without going through the VPN. As I understand it, an OpenVPN tunnel is normally set up as a default virtual internet interface, and so incoming traffic will go out on the OpenVPN interface by default (which is problematic, as this incurs latency). I thought "well, obviously, since all of this traffic is leaving on a handful of ports, I'll just redirect those to the non-VPN gateway." I've tried to look for solutions, but almost all of them involve iptables instead of ipfw (which is default for FreeBSD) and solve slightly different problems. And alternate solutions like using multiple default routes to ensure that incoming traffic on any interface is always sent out on the same interface seem far-reaching and require deep knowledge of all tools involved. Is there an elegant way of ensuring that traffic leaving on specific ports exits on a specified non-default interface using ipfw?

  Read the article

• Windows VPN - NO internet access

  - by sharru

  I host a network of servers behind a Fortigate 200a firewall in the DC. I connect to those servers via a VPN connection. The problem is that when i connect to the VPN, I lose my internet connection on the local PC (windows 7). I would like to be connected to the VPN and still surf the web. i guess this means to only forward a range of ip to the VPN connection. I've read other answers on serverfault, talking about "un-check the 'Use default gateway on remote network' option in your Windows 7 PPTP network connection settings". When i do that , i get internet access but no access to the servers in the VPN. Any idea how to get both working? Should i change something on the fortigate 200a config? Do i need two networks cards? Is there a place in windows to define ip range for the vpn connection?

  Read the article

• NSD reply from unexpected source

  - by Ximik

  I have server with NSD. There are MAIN_IP and ADD_IP. When I try to get IP of my site from server I have right output dig @localhost my_site.com But when I try to make this from my PC, I have dig @my_ns_server.com my_site.com ;; reply from unexpected source: MAIN_IP#53, expected ADD_IP#53 (ADD_IP is IP of my_ns_server.com) What should I do? UPD: My interfaces conf auto eth2 allow-hotplug eth2 iface eth2 inet static address xxx.xxx.xxx.234 netmask 255.255.255.252 network xxx.xxx.xxx.232 broadcast xxx.xxx.xxx.235 gateway xxx.xxx.xxx.233 dns-nameservers MY_ISP_IP dns-search MY_ISP_DOMAIN auto eth2:0 iface eth2:0 inet static address xxx.xxx.xxx.124 netmask 255.255.255.0 xxx.xxx.xxx is the same for all IPs

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by casey_miller

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed) So the question is: What is a problem???

  Read the article

• Failover NIC with Windows 7 running Apache Server

  - by Benjamin Jones

  I have a Apache Server running on a Windows 7 Desktop for a internal website (Intranet). I am trying to figure out how I can make this system as failover safe as possible. One thing I want to do is use the 2nd NIC card that is currently disable. I only have one gateway address to my router. I do not have any computer running a Server O/S. If NIC1 crashes by chance(just humor me!), how could NIC2's IP take on the host name (I have mapped in host file) . I don't really care if the static IP of NIC2 changes seeing that the host name is the only thing I need. Could I add two IP's to the host file, with same host email and maybe create some script that will run IF NIC 1 fails? OR is there any failover software that will do this for me?

  Read the article

• How do I change the Admin password on a Ubee DVW3201B?

  - by Iszi

  I must admit that I feel rather foolish having to ask this. I recently switched ISPs, and the new one gave us a Ubee DVW3201B as our home gateway. I want to change the Administrator username/password from the defaults, but I've been having some difficulty. Every time, after I save the new username and password, I'm prompted to re-authenticate to the administration interface. It fails no matter what I try. I've tried using: New username / New password Default username / New password Default username / Default password None of the above works. This has happened twice now, with my only recourse after failure being to do a reset to factory defaults (press and hold the hard reset button for 10 seconds). Is there something I'm missing?

  Read the article

• How to route traffic from VM (Parallels) over an Open VPN connection on the host (OS X)

  - by withakay

  Scenario: I have a Mac running Lion that is connected to an OpenVPN server I have a Windows XP VM (running on parallels, but I don't think this is important) I want to be able to route traffic from the XP VM via the host Mac's OpenVPN connection so that I can log on to a domain. The remote network is 172.16.0.0/23 (255.255.254.0) Open VPN is configured to supply address in the 10.100.101.0/24 range and sets up the routing to 172.16.0.0 using the gateway 10.100.101.1/32 My local network is 192.16.1.0/24 NOTE: I do not want to install OpenVPN into the XP virtual machine as I would have to use a passwordless key in order for OpenVPN to connect before logon. Anyone got any ideas?

  Read the article

• Accessing VMware Player across the network

  - by Tiffany Walker

  My network: 192.168.2.2 (computer) 255.255.255.0 (mask) 192.168.2.254 (gateway) The VMplayer is: 192.168.233.129 (ip) 255.255.255.0 (mask) 192.168.233.255(bcast) It's obvious the player can't be access from other systems because of the wrong network settings. However, I am not sure as to how to change that. Obviously I have to edit the ifcg-eth0 but I know I also need to edit it on the host system to make it accessably. Is this done from inside VMware Player? Or do I need to edit the network devices? The host box is Windows. Inside VMware is Linux.

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >