Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 226/286 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• GNS3 Cannot ping/resolve DNS record

  - by Eldad Cohen

  I set up an internet lab with GNS3, which has 3 routers, in each node there is a computer directly connected. One of the hosts is a DNS server, Windows 2003 Server. The other one is a Windows XP machine. Ping is good between routers and machines but no ability to ping domain.com record on DNS server 2003. I set a static nat on the router to route all traffic from gateway to the DNS server internal ip address, still no answer for the dns request. Any ideas or thoughts will be most welcome.

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Using PC or Mac keyboard as Bluetooth keyboard for iPad?

  - by Kevin Hakanson

  I would like to use my computer keyboard (USB) as a Bluetooth keyboard for my iPad, while I am using it with my computer. I was hoping their was an "app for that" that I could run on either Mac or Windows. I imagine how it would work: It would have to emulate a Bluetooth keyboard, and be able to pair with the iPad. Then, when you give focus to this app, it transmits keystrokes from your built-in keyboard out over the Bluetooth connection. Seems simple, but I can't seem to find anything definitive on Google. Has anybody done this? I figure this is cheaper that buying a Apple iPad Keyboard Dock or a Apple Wireless Keyboard from the Apple Store. Also, it's one less item on my desk, which gets cluttered enough with one keyboard.

  Read the article

• Hosting 3 domains on 3 PC (1 domain per PC) with only 1 static IP address

  - by StealthRT

  Hey all i am trying to figure this out here. I have 3 PC's that are hooked into my router which i have a static IP for. I am currently hosting a web site (ex: blah1.com) on the 1st PC but have yet to connect PC 2 and 3 up to the network. That one PC thats online is using port 77. I direct all 80 traffic to port 77 using that servers IP address (192.168.x.xxx) My question is, how can i direct traffic for my other 2 domains (ex: blah2.com and blah3.com) to the 2 individual PC's (ip's) as i already am doing with the 1st PC if i can only use one port 80 to direct taffic to the website in?

  Read the article

• Why does WebDAV fail from inside home network

  - by Claus

  On my OSX server there is a folder that is configured in the Server App to be accessible via WebDAV. This folder is used to sync OmniFocus. On my router, I have set up a dynamic dns. When I am outside my home network (physically away or when connected via a vpn), I can connect and sync fine via: https://<server name from dyndns>/<username>/<path to WebDAV folder> However, when I am in my home network, the connection to WebDAV does not work (other connections, AFP, f.ex, do work). What could be some reasons why I can't connect to WebDAV from within my home network? What log files could give hints and where are they stored? I am running OSX server 10.9.3. and server.app. Thanks for your help.

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user53864

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• Web connection speed issue

  - by Iroll750

  I encounter a strange issue with my web (wireless) connection on my laptop (Ubuntu 11.10) I'm able to have 540kbps (down) on all computers in my house (including laptop at the same distance from the box) except me. When i do a speed connection test, i can have this optimal speed immediately after booting. As i surf on the net, watching videos, download things, etc... it becomes slower progressively until 100-110 kbps and the speed remain the same until i reboot. I tried to figure out if a process consume bandwith in background with nethogs but i found nothing suspicious. Any ideas ? Thanks in advance for your help !!

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• D-Link DNS-323 NAS firmware update

  - by Mark Beaton

  Hi all, I've got a D-Link DNS-323 NAS enclosure holding a bunch of multimedia files that I've (possibly stupidly) just updated the firmware on, from 1.03 to 1.08. The updater indicated it applied the firmware patch successfully, but after rebooting it I can no longer get into it via the web interface, either via the static IP I had assigned it before the update, or by any of the DHCP-assigned addresses that I can see are currently assigned by my router. The unit just sits there, with the drives (2x512 set up as RAID-1) thrashing away seemingly forever... So, my question - has anyone had a similar experience with one of these units? Any advice etc? I've googled the hell out of it, and can't find anything useful.

  Read the article

• Sharing Internet Connection in Windows 7 is so much more frustrated than Windows XP

  - by Phuong Nguyen

  Back to the time of Windows XP, from Properties dialog of my Wireless Connection, I can enable sharing and then select LAN network from the Drop Down List and boom, I can share it with my friend. We just need a LAN cable (either cross or not-cross is OK) and his Laptop will get an auto IP to gain access to internet. But now with the new Windows 7, everything starts to suck. I cannot see the Drop Down List any more in the sharing panel and my friends Laptop cannot get an automatic IP anymore. Am I doing anything wrong over there? How can I gain back the peace I used to have with Windows XP?

  Read the article

• Program to see, which programs use the internet-connection?

  - by Martti Laine

  Hello Few days ago I opened my computer as I always do after school, and got pretty amazed about my 1.27kb/s download-speed. It has continued for few days already. We have a wireless network, which is used by 3 computers. Normally I've gotten 200kb/s (I think we have a 2mb-connection) but now it just suddenly slowed down. My friends have the same service-provider, but no problem. So, is there any kind of program, which would show me all the programs using connection and how much. It must be a program open which just takes all speed off. Any help is appreciated, Martti Laine

  Read the article

• Nagios check_bgp_neighbors plugin showing critical status

  - by user141610

  I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C snmpName -n xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. Status information: line: neighbor:xx.xx.xx.50:sent:78838:received:9769 Failed: status:6 prefixes:16 sent:0 received:1 Log [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-email;line: neighbor:103.7.248.50:sent:78842:received:9772 [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-sms;line: neighbor:103.7.248.50:sent:78842:received:9772 Why does it show critical status???? I am not getting response for this question, if you need additional information please mention it in comment.

  Read the article

• Resolving real IP address out of a dynamic dns address

  - by stavnir

  I recently opened a dynamic dns user (at no-ip for that matter..) for my own personal needs and especially for ssh-ing my computer whenever I need to, without knowing it's static IP. My questions are: Am I misusing the concept of dynamic dns? Are there more appropriate methods to do what I want to do? If not, how do I resolve my router's real ip address? Firefox somehow manages to do so, nslookup and other similar commands only resolve the ip of the ddns server (e.g. no-ip.org). Trying to figure this mystery with wireshark failed miserably ;)

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• Trouble accessing network drives in Windows 7

  - by Warlax

  Hi, Recently purchased a LaCiE network drive. Connected it to my router, configured it, added a user for myself. Installed the "Network Assistant" that came with it - no problem. Went to My Computer Network, found the network drive - was prompted for a login/password to see the contents, types \user and password (leading slash to get rid of DOMAIN) and accesses contents. There is one open share that I can access/mount without problem and there's another share with my user name as set-up via the network drive's web-based config. Double-clicked on that, prompted again. user/password doesn't work! It says I have no permissions but the user/pass combination is PERFECT. Some Windows Vista posts talk about a Local Security Policy menu - but that's nowhere to be found. Any ideas? (Windows 7 Professional BTW).

  Read the article

• Sharing Internet Connection in Windows 7 is so much more frustrated than Windows XP

  - by Phuong Nguyen

  Back to the time of Windows XP, from Properties dialog of my Wireless Connection, I can enable sharing and then select LAN network from the Drop Down List and boom, I can share it with my friend. We just need a LAN cable (either cross or not-cross is OK) and his Laptop will get an auto IP to gain access to internet. But now with the new Windows 7, everything starts to suck. I cannot see the Drop Down List any more in the sharing panel and my friends Laptop cannot get an automatic IP anymore. Am I doing anything wrong over there? How can I gain back the peace I used to have with Windows XP?

  Read the article

• Does a USB to RJ-45 console cable exist?

  - by Carl Flippin

  I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

  Read the article

• Can a device (WAP or switch) be configured as an 802.1x supplicant?

  - by Allan Ross

  We are looking at implementing 802.1x on a wired/wireless network. What I am looking for is a device that can act as a supplicant and once authenticated on the network, is able to pass traffic from any downstream connected device. The point of doing this would be to allow a properly pre-configured device to be provided to a client user who could then connect any device on the downstream side of the device. We will be able to manage the aggregate traffic on the device without concern for what is connected on the far side. Am I dreaming; does every device out there support this and I just don't know it or is reality fall somewhere in the middle?

  Read the article

• My server app works strangely. What could be the reason(s)?

  - by Poni

  Hi! I've written a server app (two parts actually; proxy server and a game server) using C++ (board game). It uses IOCP as the sockets interface. For that app I've also written a "client simulator" (hereafter "client") app that spawns many client connections, where each of them plays, in very high speed, getting the CPU to be 100% utilized. So, that's how it goes in terms of topology: Game server - holds the game state. Real players do not connect it directly but through the proxy server. When a player joins a game, the proxy actually asks for it on behalf of that player, and the game server spawns a "player instance" for that player, and from now on, every notification between the game server and the player is being passed through the proxy. Proxy server - holds TCP connections with the real players. Players communicate with the game server through it only. Client simulator - connects to the proxy only. When running the server (again, it's actually two server apps) & client locally it all works just fine. I'm talking about 40k+ player instances in which all of them are active in a game. On the other hand, when running the server remotely with, say, 1000 clients who play things getting strange. For example, I run it as said above. Then with Task Manager I kill the client simulator app ("End Process Tree"). Then it seems like the buffer of the remote server got modified by another thread, or in other words, a memory corruption has been occurred. The server crashes because it got an unknown message id (it's a custom protocol where each message has it's own unique number). To make things clear, here is how I run the apps: PC1 - game server and clients simulator (because the clients will connect the proxy). PC2 - proxy server. The strangest thing is this: Only the remote side gets "corrupted". Remote in terms that it's not the PC I use to code the app (VC++ 2008). Let's call the PC I use to code the apps "PC1". Now for example, if this time I ran the game server on PC1 (it means that proxy server on PC2 and clients simulator on PC1), then the proxy server crashes with an "unknown message id" error. Another variation is when I run the proxy server on PC1 (again, the dev machine), the game server and the clients simulator on PC2, then the game server on PC2 gets crashed. As for the IOCP config: The servers' internal connections use the default receive/send buffer sizes. Tried even with setting them to 1MB, but no luck. I have three PCs in total; 2 x Vista 64bit <<-- one of those is the dev machine. The other is connected through WiFi. 1 x WinXP 32bit They're all connected in a "full duplex" manner. What could be the reason? Tried about everything; Stack tracing, recording some actions (like read/write logging).. I want to stress that only the PC I'm not using to code the apps crashes (actually the server app "role" which is running on it - sometimes the game server and sometimes the proxy server). At first I thought that maybe the wireless PC has problems (it's wireless..) but: TCP has it's own mechanisms to make sure the packet is delivered properly. Also, a crash also happens when trying it with the two PCs that are physically connected (Vista vs. XP). Another option is that the Windows DLLs versions might have problems, but then again, one of the tests is Vista vs. Vista, and the other is Vista vs. XP. Any idea?

  Read the article

• Error while setting up Anywhere Access on Windows Server 2012 Essential (personalized domain name from Microsoft)

  - by Thomas

  I am trying to setup Anywhere Access on a Windows Server 2012 Essential Release Candidate, but keep getting this error: "The domain name was not setup for your server. Wait a few minutes and run the wizard again. An unknown error occurred. Please wait a few minutes and then try again". These are the options that I selected in the Wizard: I want to set up a new domain name Get a personalized domain name from Microsoft Entered my Windows live id and password xxxx.remotewebaccess.com And on the next page the error is displayed. I have setup my router (Linksys WRT160N) to forward all TCP traffic to the Server. UPnP is also enabled. If I hit my public (dynamic) IP (http://188.182.194.182/) I get the Windows Server 2012 homepage. Any ideas?

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers? What we ended up doing In case anyone are courious, we ended up doing seperate VLANs for each user. And as a matter of fact, not just the 550 users, but for 2500 users (11 dorms). Here's a page describing the setup: http://k-net.dk/technicalsetup/ (the section "Transparent firewall using VLANs"). There was no significant load on the router server as I feared in one of the comments below. Even at 800Mpbs.

  Read the article

• unusual webpage access problem

  - by user28163

  This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• Cannot access SWITCH thru VPN

  - by MadBoy

  I've VPN connection set up that i connect to company with. I can connect to all devices (other switches, routers, servers from same subnet with same settings just diffrent ip) but I can't connect to NetGear Router GS748Tv3. Settings on switch: IP address 192.168.1.8 Subnet mask 255.255.255.0 Default gateway 192.168.1.1 Management VLAN ID: 0 (1 - 4094 or 0) (0 means all VLANs) Switch has 2 VLAN's configured 1 and 2. I can access this switch thru VPN if i log in to server and from server to switch but this is a little bit slower then normal way. Anything I'm missing?

  Read the article

• How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

  - by vm370

  as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >