Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 230/286 | < Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >

• once VPNed into pfSense, unable to hit the public URLs of my websites - they are routed to the pfSense box

  - by Sean

  I have a pfSense box setup as the firewall/router/VPN appliance at my colo. Once I VPN into the colo (either pptp or openvpn, pptp preferred due to multiple clients and ease of configuration), I am able to hit all my servers by their private 10.10.10.x ip and am able to browse the public internet without issue. When I try and hit the URL of a domain hosted by one of my servers, I am prompted for credentials. If I login using the pfSense credentials, I'm connected to pfSense as if I'd used it's internal IP. If I hack my hosts file to point url - server private IP it works fine, but this is obviously not a good solution. To recap: not connected to VPN - www.myurl.com works connected to VPN - www.myurl.com never makes it to the correct server, but is sent only to the pfSense box I'm sure it's something small that I've missed in the pfSense config.

  Read the article

• Is it possible to combine two internet connections to increase performance?

  - by cornjuliox

  I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

  Read the article

• Instructions to setup domain controller

  - by Robert Koritnik

  Where could I get best step by step instructions (with some simple explanations) how to setup domain controller on Windows Server 2008 R2 Server Core? I don't know what do I need? Do I need DNS as well and AD and so on and so forth. I don't know enough about these things, but I need to set them up to prepare development environment. I would also like to know how to configure firewall on DC machine, to make it visible on other machines because I've setup DC somehow but I can't connect to it... This is my HW config: Linksys internet router with DHCP my dev machine is Windows 7 my DC machine is a VM in my dev machine my dev machine has a network adapter to linksys and a virtual adapter to DC DC machine has two network adapters: one to linksys (to be inetrnet connected) and one to host (my dev Win7 machine)

  Read the article

• Performance issues with jms and spring integration. What is wrong with the following configuration?

  - by user358448

  I have a jms producer, which generates many messages per second, which are sent to amq persistent queue and are consumed by single consumer, which needs to process them sequentially. But it seems that the producer is much faster than the consumer and i am having performance and memory problems. Messages are fetched very very slowly and the consuming seems to happen on intervals (the consumer "asks" for messages in polling fashion, which is strange?!) Basically everything happens with spring integration. Here is the configuration at the producer side. First stake messages come in stakesInMemoryChannel, from there, they are filtered throw the filteredStakesChannel and from there they are going into the jms queue (using executor so the sending will happen in separate thread) <bean id="stakesQueue" class="org.apache.activemq.command.ActiveMQQueue"> <constructor-arg name="name" value="${jms.stakes.queue.name}" /> </bean> <int:channel id="stakesInMemoryChannel" /> <int:channel id="filteredStakesChannel" > <int:dispatcher task-executor="taskExecutor"/> </int:channel> <bean id="stakeFilterService" class="cayetano.games.stake.StakeFilterService"/> <int:filter input-channel="stakesInMemoryChannel" output-channel="filteredStakesChannel" throw-exception-on-rejection="false" expression="true"/> <jms:outbound-channel-adapter channel="filteredStakesChannel" destination="stakesQueue" delivery-persistent="true" explicit-qos-enabled="true" /> <task:executor id="taskExecutor" pool-size="100" /> The other application is consuming the messages like this... The messages come in stakesInputChannel from the jms stakesQueue, after that they are routed to 2 separate channels, one persists the message and the other do some other stuff, lets call it "processing". <bean id="stakesQueue" class="org.apache.activemq.command.ActiveMQQueue"> <constructor-arg name="name" value="${jms.stakes.queue.name}" /> </bean> <jms:message-driven-channel-adapter channel="stakesInputChannel" destination="stakesQueue" acknowledge="auto" concurrent-consumers="1" max-concurrent-consumers="1" /> <int:publish-subscribe-channel id="stakesInputChannel" /> <int:channel id="persistStakesChannel" /> <int:channel id="processStakesChannel" /> <int:recipient-list-router id="customRouter" input-channel="stakesInputChannel" timeout="3000" ignore-send-failures="true" apply-sequence="true" > <int:recipient channel="persistStakesChannel"/> <int:recipient channel="processStakesChannel"/> </int:recipient-list-router> <bean id="prefetchPolicy" class="org.apache.activemq.ActiveMQPrefetchPolicy"> <property name="queuePrefetch" value="${jms.broker.prefetch.policy}" /> </bean> <bean id="connectionFactory" class="org.springframework.jms.connection.CachingConnectionFactory"> <property name="targetConnectionFactory"> <bean class="org.apache.activemq.ActiveMQConnectionFactory"> <property name="brokerURL" value="${jms.broker.url}" /> <property name="prefetchPolicy" ref="prefetchPolicy" /> <property name="optimizeAcknowledge" value="true" /> <property name="useAsyncSend" value="true" /> </bean> </property> <property name="sessionCacheSize" value="10"/> <property name="cacheProducers" value="false"/> </bean>

  Read the article

• Mikrotik queues and limiting total upstream bandwidth

  - by g18c

  With a Mikrotik router (form of embedded Linux) I have created simple queues per machine matched by source IP address. Each of the 4 machine queues has an unlimited burst 3Mbps/3Mbps for Tx/Rx. During speedtest.net on all 4 machines at the same time, each machine shows 3Mbps (and is limited correctly there), however the total bandwidth on the uplink goes to 12Mbps (i need to set this to 10Mbps max for the upstream). I want to restrict the actual traffic passing across the uplink port to 10Mbps regardless of what the other queues are doing (I need this catch all queue to have the final say on the uplink speed). For example I need: Scenario A Machine A transferring @ 3Mbps Machine B transferring @ 3Mbps Machine C transferring @ 3Mbps Machine D transferring @ 0Mbps Up-link speed = 9Mbps Scenario B Machine A trying to transfer @ 3Mbps Machine B trying to transfer @ 3Mbps Machine C trying to transfer @ 3Mbps Machine D trying to transfer @ 3Mbps Up-link speed = 10Mbps Actual transfer speed of machine A,B,C,D = 2.5Mbps This is to allow slight over subscription of bandwidth queues as not all will be transmitting at 3Mbps all the time. Is this possible and if so how would one go about doing this?

  Read the article

• Creating a custom NAS compatible with the Mac Time machine and for media streaming

  - by Bobby Alexander

  I am planning to assemble a custom NAS machine using an Intel Atom processor. I need the NAS for the following purposes: It should be accessible from by Windows PC so that I can dump data on the NAS (installations, media etc) It should be accessible from my Macbook for the above use. I should be able to use it with the Mac time machine software for backup. The media should be available to my PS3 for streaming. I should be able to access it from my iphone. All the above features should be available over wireless. The time machine feature is very important. Is this even possible? Can someone provide resources on how I can assemble such a machine and setup the required software on it? Much appreciated.

  Read the article

• Subdomain only accessible from one computer

  - by Edan Maor

  I recently added a wildcard A record to my domain (*.root.com), mapping it to a certain elastic ip on AWS. I've configured apache to redirect all references to something.root.com to root.com, except for one specific "dev" subdomain, which is hosting its own site (a Django app, specifically). The Problem: This setup works perfectly for me on my computer. But on other computers around the office, it doesn't seem to work. Specifically, trying to visit dev.root.com gives an "unable to find server" error. Pinging dev.root.com gives a "cannot resolve hostname" error. The weird thing: pinging any other subdomain of root.com does work, from all machines. I would think this was all due to DNS propagation, except all the computers are behind the same office router, so how could that be the case? Any ideas?

  Read the article

• TheGreenBow VPN with Cisco 2811 config

  - by Fujishiro

  Okay. Im using the feared x64 Win7 retail. I tried soooo many clients/methods, but none of them worked. Finally after a long battle, I made TGB working. YAY! I only have problems with the configuration. What data I've got? group auth user+pw;3DES enc(saw it from the router cfg);user+password. And that's all. I tried using the TGB provided manual and the howtos on their site, but there is no instruction for the given model, and the other cisco type conf wont work.) I tried to configure it up, but its not that easy.. as I mentioned aldy. If anyone uses this app or knows how to configure it up... please..help me.

  Read the article

• Files turned into folders on external hard drive

  - by Kashif

  I have a networked hard drive where I like to store audio/video/software and all sorts of other files for my house. While the software files are all intact and working, many of my video and audio files have been turned into folders! Can anyone explain why this is happening, how I can prevent it, and if it is possible to revert these "folders" back into files. Thanks much! An example of what the folders are named: "Highschool Graduation.avi", "Birthday party.avi", "Somesong.mp3" The HDD is connected to a Linksys E4200 router (Firmware Version: 2.0.37). This is how the HDD is networked.

  Read the article

• After installing Windows what should I do first? update or install antivirus?

  - by EApubs

  Normally, after reformating and installing Windows 7, I used to go online and install all the updates, install all the driver updates and then install the anti virus. Because long ago, when I installed the anti virus first, applying windows updates crashed the AV! So, I install it last. Specially 7 sp1 is critical right? But now im having doubts... Going online without an antivirus means I'm vulnerable! (I have a home router which have a small firewall but I'm not sure about it) So, whats the best thing to do? Install the anti virus first or install the updates first?

  Read the article

• modprobe ndiswrapper - not found

  - by David

  I'm trying to use ndiswrapper on a Slackware 12 (I think) box, but I'm running into a problem with modprobe. Everything I find online says that it should be working, but for some unknown reason it isn't. Here's what I've done so far: Installed ndiswrapper (latest tarball, make, make install) Ran ndiswrapper -i on the WinXP driver for my USB wireless card Ran ndiswrapper -l which tells me the driver is present and the device is present (lsusb also confirms the device is present) Ran ndiswrapper -m which put an alias for wlan0 in /etc/modprobe.d/ndiswrapper.conf Ran depmod -a Ran modprobe ndiswrapper which tells me "FATAL: module ndiswrapper not found" Ran modprobe -l which shows no listing for ndiswrapper I even tossed in a reboot or two while trying various combinations of the above, still nothing. So naturally ifconfig wlan0 up isn't working because the device isn't being created, presumably because the module isn't loading the driver. Does anybody have any suggestions? Everything points to the notion that this should work fine, but modprobe just isn't able to find what it needs. Have I missed an important step?

  Read the article

• Linux IPv6: DHCP and /127 prefixes

  - by Jeff Ferland

  I've tried multiple pieces of DHCP client and software in attempting to setup a solution for allocating a /127 prefix to virtual machines so that each maintains its own layer 2 isolation. Because there would only be one host assigned to each network, a /64 is impractical. While the prefix size could reasonably be somewhere in the /64-127 range, the crux of the problem has been the same regardless of the software used in configuring: the DHCP call to bring up the interface uses the address advertised by DHCPv6 and inserts two routes: the /127 given by the router advertising packets and a /64 as well. Any thoughts on why I'm getting the additional route added across dhcp client vendors?

  Read the article

• Logitech Mouse stopped working after changing batteries!

  - by Martti Laine

  I just changed batteries for my optical wireless Logitech mouse, but it stopped working; When I put it on, it waits a second and then keeps the green light for few seconds. After that it just stops responding and doesn't show the light even if I'm moving it. Does this have something to do with batteries? I took new, so they're not empty. And I think it cannot be on batteries, because it keeps the light first, but then just stops responding. Please help, I would be very very thankfull. This makes me mad to use this mousepad :D EDIT: Wow, what an fast answer!! Thank you, but you wanted to know this mouse? I think it's Logitech M205, watched from Logitech site, because have not the original package anymore :S I couldn't find any buttons in receiver, but mouse has button called "reset". Is that the right one?

  Read the article

• Unable to FTP, any ideas?

  - by Nick

  I'm using Windows Server 2003. I have the FTP services installed, router set to DMZ, and currently Anonymous logins allowed. (I know, security risk, but there's nothing important on there and not worried at the moment) So here's the thing... I can ftp to my computer, list directory, get files etc, BUT only if I'm using the command prompt. If I try to log in using IE or any FTP client it's just timing out. I've tried: username@ipaddress ipaddress username:password@ipaddress and not able to get any of them to work. Anyone have any ideas? Thanks!!!

  Read the article

• Port forwarding not working?

  - by rphello101

  I'm trying to set up an Apache Server to be accessed publicly. I'm using a Netgear R4500 router hooked up to a Motorola SB6121 modem. I can access my server on my computer by typing in my IP address. After following the instructions to forward port 80 so I can access the server from other computers, it does not work (see image). I get "This webpage is not available". I am forwarding to the IP address of my computer. Using this Network Port Scanner Tool, it says "80/tcp filtered http", which, as I understand it, means forwarding did not work correctly. In my Apache httpd file, I have: ServerName 192.168.1.13:80 and Listen 192.168.1.13:80 Anyone know what's wrong or have something I can try? click to enlarge

  Read the article

• Slow Internet connection

  - by Muthu Kumaran P

  My internet connectivity from my Laptop slowed down overnight. I have no clue as what had happened. I was able to download at 300kbps the day before yesterday. And from yesterday on, my internet has been slow. My download speed is at 25kbps. Can someone help me to resolve this issue? I am using wireless connection on my Sony Vaio. I am not sure what else info I need to give as this is my first time to post a question here..

  Read the article

• Is there a way to make scp run faster on a Mac OS X?

  - by paul_sns

  I'm trying to a upload a Flex generated SWF file from my Macbook (running Snow Leopard) using the command scp main.swf server.com:/ I had setup key authentication to prevent typing the user/pass every time. This process normally takes up to two minutes using my connection at home (768kbps down/300+ kbps up). The interesting part is that when I use WinSCP in my Windows XP machine, the process only takes 30 seconds max. Both my MacBook and Windows XP machine use the same internet connection. The MacBook is connected to the router via cable (which should be faster right?) while the Windows XP connects through Wifi. Let me know if you need additional information in order to diagnose the problem. Thanks!

  Read the article

• Routing Traffic on Ubuntu to give Raspberry PI Internet Access

  - by Scruffers

  I'm hoping someone can point me in the right direction for setting up my Linux (Ubuntu 12.04) box to route traffic from eth0 to wlan0. I'll try and explain the problem I am trying to solve: I currently have two separate networks: [RaspberryPi/eth0] 192.168.2.2 / 255.255.255.0 ^ | v [Ubuntu/eth0] 192.168.2.1 / 255.255.255.0 And: [Ubuntu/wlan0] 192.168.1.100 / 255.255.255.0 ^ | v [ADSL router] 192.168.1.1 / 255.255.255.0 So currently if I want to access the RaspberryPI I can SSH from the Ubuntu box to the PI. And if I want to use the Internet, I have full access from the Ubuntu box, but nothing from the RaspberryPI - the two networks are partitioned. What I would like to do is configure things so that the RaspberryPI has Internet access via the Ubuntu box and out to the Internet. I tried to create a bridge, but got the message "wlan0: operation not supported" (wireless chipset is Ralink RT3062). I'm sure giving the Raspberry PI Internet access should be easy to do in this configuration, but I am a bit lost - can someone point me in the right direction please?

  Read the article

• How to configure Windows Server 2008 DHCP to supply unique subnet to a remote site?

  - by caleban

  The Main site hosts the only Windows Server. Windows Server 2008 R2 Domain Controller running AD, DNS, DHCP, Exchange 2007. Remote site has no Windows server. Main site subnet is 192.168.1.0/24 Remote site subnet is 192.168.2.0/24 The Windows Server at Main site is supplying 192.168.1.0/24 via DHCP to hosts at the local site where it resides. Is it possible to configure that Windows Server to supply 192.168.2.0/24 to hosts at the Remote site and if so how? We could use the Cisco router at the Remote site to supply DHCP but if possible we'd like to use the Windows Server at the Main site to supply DHCP.

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• NAT Error Message - Usage limit exceeded

  - by Kato

  Trying to configure a port to use for Vuze. Using the NAT/server port test, I was getting a message saying the connection timed out, the port was probably closed. I went back and made sure to open the specific port on my router, firewall, etc, but now I'm getting "NAT Error - Usage limit exceeded (173.32.41.24:0). I'm on a mac pro running leopard, trial versions of intego netbarrier and virusbarrier. Network utilities and netbarrier both claim the port is open. I've tested a bunch of other ports, but all give the same message.

  Read the article

• How can I run a game server on a computer behind a NAT, if I have another computer not behind a NAT?

  - by Macha

  My home connection is part of a large NAT, outside my control. Inside my home, my router has a NAT, under my control. I control a public facing Linux VPS with one IP address, outside my home network. Ideally, what I'd like to do is set something up so that I connect my home computer to my VPS, and after that port X on my VPS leads to port Y on my home computer, for the purposes of running a game server of a game that does not run under Linux. Is this possible?

  Read the article

• Is there a free tool/package that can monitor web traffic and display URLS accessed? [closed]

  - by Anthony

  I couldn't find a similar question but then maybe I am searching for the wrong terms. A few years ago I used a router like device, I'm pretty sure it was a SonicWall, that did this on a clients site. Basically all traffic would be routed through this device and it allowed the manager/administrator to inspect web usage of the workers, determine how often certain resources were accessed and block them if necessary (much like content filter). It showed reports based on domain name reached etc. Facebbok.com, Bebo.com and so on. It also displayed the usual IP traffic information etc. it was a UTM also. I have tried Endian firewall, with it's NTOP install, but I don't think that will show URLs browsed. Maybe I just haven't found it in NTOP yet? I need this to troubleshoot connection and traffic issue at my home, with about twenty devices/users so didn't want to buy a dedicated solution and have spare hardware to use a community product.

  Read the article

• Is there a way to get att.net email to stay connected?

  - by Clay Shannon

  My att.net account at home (wireless connection) has been bad for the last several days: I have to hit F5 quite a few times to "unfreeze" it (I can read an email or two, then it freezes, etc.). At work (company LAN) it's even worse: I can connect to the site and see that I have email, but can't open any of the emails - and the screen constantly refreshes (every couple of seconds) with a "Connecting..." message. It apparently connects and disconnects over and over again, but never stays connected long enough to actually access the email. Is there a way either to fix this OR forward my att.net (from home) to my work email address (accessible via MS Outlook)? Or set it up from work using Outlook to pull in my att.net email? I have Outlook 2003 at work.

  Read the article

• How to get Apache web server to run on other computers?

  - by Eric

  I have been using Apache Web Server for a while now and one thing I have noticed is that outside of my computer I can not access it. I use my Apache server for PHP development on my computer, but I would like to access stuff I have made outside of my computer. I am on a linksys router network. I usually run it of http://localhost/ or http://127.0.0.1/. I IPCONFIGED my computer and got 192.168.1.105 so I went there with my browser and got the page just fine. I tried doing this on another computer on the same network but it didn't work. How do I fix this? Sorry about the bad wording. I am in ah hurry Information you might need to know: Server: Apache 2.2 Operating System: Windows 7 ULTIMATE

  Read the article

< Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >