Search Results

Search found 756 results on 31 pages for 'acer travelmate'.

Page 23/31 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• How to disable Microsoft eHome MCIR Keyboard and company?

  - by AndrejaKo

  Hi! I'm and unlucky owner of and Acer 7720G laptop which, like many in its category, has receiver for a proprietary infra red remote control device (which I did not receive with my laptop!) . Now my problem is that the receiver is detected as Microsoft eHome MCIR Keyboard, Microsoft eHome MCIR 109 Keyboard and Microsoft eHome Remote Control Keyboard keys. My problem is that this driver has incompatibilities with some programs I use like for example DosBox. When these devices are installed, they cause DosBox to incorrectly detect some keyboard buttons. The workaround is to remove or disable the 3 hardware devices. Unfortunately, I the disable option is grayed out and when I delete them, they are reinstalled on next restart. Is there any way to hack windows in order to prevent their installation? I was thinking about locating the drivers these devices use, but they are buried somewhere in windows installation and I don't have enough experience to find them, so I'm asking you for help.

  Read the article

• Proxy Appliance

  - by Kumar

  I'm looking for a way to set-up a web proxy at home. Hopefully there's a solution I can use to do this. Alternatively, do you have any ideas for setting up one at home using a proxy with an auto updating list? UPDATE - AutoUpdating list so the new sites are categorized and downloaded and the filtering is done by category instead of per site e.g. peerblock works this way Appliance as in a small dedicated hardware or device to perform this task, like WD TV live or Acer Aspire Revo with the media center edition I'd be ok with setting up Squid / Linux / SquidGuard even if i'm not familiar with *nix but ideally a small form factor pc with dual nic's would be ideal so it can be out of sight for the most part !

  Read the article

• Black screen after grub kernal selection menu

  - by skip

  I have an Acer eMachines e727 with Intel GMA 4500M integrated graphics (drivers updated to latest). I installed Ubuntu 12.04 using Wubi. All is well until I select the kernal (first one on the list). My display goes black. I searched for solutions and found one on Unbuntu forum which partially helped. Following that sticky post, I pressed "e" at the kernal listings. I changed the $Linux... default line to "quiet splash nomodeset" and was able to get to the login screen and desktop. I edited grub to make the nomodeset permanent (also removed the vt command as recommended). I followed through with changing grub to match the graphics as recommended in the article using the grub cli (using info from vbeinfo). I updated grub with the recommended settings but still get the black screen after selecting the kernal. Only nomodeset works to get me to the login and desktop. Once I get to the desktop, my display resolution shows being set to 1024x768 but it actually looks like 800x680. What do I need to do to get past these issues? Thanks!

  Read the article

• Error installing Arch Linux

  - by Garethj94

  So, I am trying to install Arch Linux on my Acer Aspire 4830tg, but I keep running into problems. Some background knowledge, I am trying to install Arch off a usb stick and I got the iso image using bittorrent. I am also trying to install it alongside of Windows 8 (which is already installed). So when I boot into Arch linux I get this error: :: Mounting '/dev/disk/by-label/ARCH_201212' to 'run/archiso/bootmnt' Waiting 30 seconds for device /dev/disk/by-label/ARCH_201212 ... ERROR: '/dev/disk/by-label/ARCH_201212' device did not show up after 30 seconds... Falling back to interactive prompt You can try to fix the problem manually, log out when you are finished sh: can't access tty; job control turned off I know that it will work if I run it on a virtual machine but whenever I try to install it on my laptop I keep getting this error. And since you can't register for the Arch forums without a Arch terminal to run their captcha command I can't ask this on their forums.

  Read the article

• Ubuntu 12.04 NVIDIA GeForce Go 7600 black screen during boot

  - by Florian Schmidt

  I'm using Ubuntu as the only operating system since two years. In the first Ubuntu versions I had seen my BIOS screen and the boot screens. Actually im using Ubuntu 12.04 and my screen stays black until Ubuntu is started (both screens are missing). I guess this situation appeared the first time in Ubuntu 11 (not sure). I searched via google and tried the popular activities but was not able to fix my issue. I opened the laptop and checked all connections. I'm using boot option nomodeset. I had a look through many many web pages. I don't know how to continue and hope somebody could be helpful. My hardware: Acer Aspire 9300 AMD Turion 64 x2 NVIDIA GeForce Go 7600 (using proposed driver) lspci | grep NVIDIA 00:00.0 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:04.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 03:00.0 VGA compatible controller: NVIDIA Corporation G73 [GeForce Go 7600] (rev a1) So my question is what to do to fix the black screen during boot?

  Read the article

• What is the most economic hardware that will run Ubuntu? [closed]

  - by nbolton

  I'm looking to buy the cheapest hardware I can find that will run the latest version of Ubuntu desktop on some sort of usable level (e.g. use of web browser, flash, etc). I guess small form factor would be pretty convenient, so I was looking at Acer Aspire Revo for example, but I'm not sure whether or not it's overpriced. I'd rather pay less for the same thing minus brand name if it's available. Any ideas? On further investigation, it seems I'm looking for a nettop.

  Read the article

• Can the NVIDIA ION chipset handle streaming and gaming reasonable well?

  - by true_gritt

  I'm considering getting a small-footprint "nettop" computer to use as a home theater PC with my Samsung LN40A550 HDTV. I've been looking at systems like the AS Rock ION HT330, the Acer AspireRevo 3610, or the Asus EeeBox PC EB1501. These are all systems with NVIDIA ION chipset (Intel Atom N330 dual core CPU + NVIDIA GeForce 9400 GPU). Is the NVIDIA ION chipset powerful enough to support media streaming at HD resolutions (e.g. via Boxee, Hulu, Netflix) and casual gaming (e.g. World of Warcraft, Madden NFL) reasonably well without herky-jerky video output?

  Read the article

• Burned white shadow on 24inch monitor

  - by elias94xx

  So I got this brand new monitor today an noticed the following problem: This happens while I'm moving my browser window for example. It's not font related, it also happens with icons as you can see on the picture. It's only persistend while I'm moving something, the faster I move it, the farther away is the shadow from the origin. I tested it on windows, linux and two different systems with DVI and VGA. Is this a known issue ? Specifications: Name: Acer S242HLCBID 1920x1080 @ 60hz 2ms response time contrast: 100.000.000:1 manufacture date: week 48 2011 LED backlights

  Read the article

• 1 TB hdd and no space to create a partition for linux !

  - by rangalo

  I have a brand new Acer aspire 5811 with core i5 processor and all that. There is windows 7 Home Premium pre-installed on it. I want to install arch and setup a dual boot system. The problem is: Windows shows 4 partitions 14 MB UNKNOWN recovery partition 100MB NTFS System Reserved partition for Windows 7 448GB NTFS Windows 7 system partition 468GB NTFS Data partition for windows 7 But GpartedLive cd and also arch setup show 5 partitions 938Kb UNKOWN system reserved partition 14 MB UNKNOWN recovery partition 100MB NTFS System Reserved partition for Windows 7 448GB NTFS Windows 7 system partition 468GB unusable space Because of this, I cannot create another primary partition. Can any body guide me about how should I go for creating partition for installing arch ? Note: I need to keep windows 7 working. regards.

  Read the article

• virtual machines: optimal host os to run Windows XP guest os?

  - by user61132

  My department doesn't have the budget to upgrade my ailing Dell D620 laptop. However, I do have the option to buy my own personal computer, then use my company-issued ISO image to run Windows XP as my guest os using virtualbox or vmware. Therefore, last month, I bought an Acer AX3910-U3012 desktop that had Windows 7 as the host os (and 8G RAM). In short, I was disappointed with the performance while trying to run WinXP as the guest os. (It didn't perform much better than my laptop.) Just wondering what the optimal host os would be for running Windows XP as the guest os? (No, I can't use my company-issued ISO image to build the os for my personal computer.) FWIW, I'm willing to spend up to $2k if it's REALLY worth it, but would prefer to spend no more than $1k. Also, in an effort to cut costs, I'd prefer buy a desktop instead of a laptop. Thanks for any/all feedback.

  Read the article

• Installed on a machine with EFI and after installation, it says the disk is not bootable

  - by Roy Hocknull

  I installed Ubuntu 11.10 and the installation runs through fine. It then says reboot, and the machine says 'inserts a boot disk' which means the hard disk isn't bootable. The primary hard disk is an EFI device, and nothing seems to work. The machine in question is an Acer Aspire M3970 desktop. Core i5 2300, with 8Gb Ram. Main boot drive is an SSD (Vertex 2E 60Gb). I am trying to install the 11.10 x64 version. The installation I have tried from CD and USB stick. It goes through the install, allows you to partition the drives then installs all the packages. At the end it goes for a reboot, and asks you to remove the installation media. The PC then restarts and says no bootable disk. I tried it many times. In the end I have installed Fedora 15 x64 which works straight away with no messing. Unless this issues is fixed I have to drop 11.10 as a viable option. From my experience F15 isn't quite as polished as Ubuntu, but in this case - it works!! Is this a widespread problem or am I unique?

  Read the article

• Does OneNote have palm rejection or a hand rest spot?

  - by Richard DesLonde

  I just bought an Acer Iconia W500. I really wanted to use it for taking notes and having all the amenities of a full blown computer without the size. Using OneNote to take notes, I notice I can't rest my hand on the screen. I have read some about this and it seems the very best solution is to get a tablet with active digitizer technology, but there aren't too many with this and it is expensive. So barring that, is there any way I can rest my hand on the tablet screen while taking notes in OneNote? Or am I relegated to hovering my hand over the screen while I write notes? Does OneNote have a palm rest area or some sort of palm rejection?

  Read the article

• Laptop battery: is voltage really important to respect?

  - by Fox

  I got an Acer Aspire 5100 and I just bought a new battery (after the stock battery just died yesterday). But I saw something after buying and I'm wondering whether it's really important or not. My stock battery was a 6-cell 4000mah 11.1v and the new battery is an 8-cell 4800mah 14.8v . I know that 8-cell and 4800mah is okay, but what about the 14.8v instead of 11.1v? The battery description says it's compatible with my laptop model (AS5100, model BL51), but the voltage difference makes me wonder. Will the laptop only take what it needs? Or will it be getting 14.8v straight in the brain? I know that my wall plug claims to output 19v, so logically I'm thinking a higher voltage battery shouldn't be a problem. Am I correct in thinking this? Thanks in advance for your answers!

  Read the article

• laptop overheating ran defraggler and now its not as hot

  - by Marko

  Trying to diagnose and fix an overheating Acer 5735 laptop, running speedfan and doing general workload to try and cause the overheat conditions. I notice that windows xp is badly fragmented according to defraggler, at 58% fragmentation. So I defrag whilst watching the speedfan window, which was at the start reporting high warning style symbols for all of the sensors. After the defrag, I rebooted and ran a few programs, and even defraggler again and the sensors in speedfan all reported green i.e. not high. Wondering if there is a correlation between windows fragmentation causing the hard drive to work harder and produce more heat inside the laptop? dont want to just assume that the problems are resolved, so either speedfan is not accurate enough or fragmentation can lead to additional hard drive heat? All comments or suggestions welcome.

  Read the article

• Xubuntu 12.04 : Random boot to black screen

  - by Thibaud Ruelle

  My xubuntu 12.04 has worked flawlessly since install in September. However, lately I randomly have the following boot issue : The computer boots to grub, and after choosing xubuntu either boots normally or boots to a black screen. Here are some observations I have made : The black screen seems to happen randomly. The black screen does not seem to happen in safe mode (- nomodeset in grub). The black screen does not allow me to ctrl + alt + F1-6 into a terminal. The black screen allows me to use SysRq keys (Alt + SysRq + K does not work though). The black screen often happens on first boot in several hours and the computer usually boots normally after a RSEINUB. When the computer boots I get "SP5100 TCO timer: mmio address 0xfec000f0 already in use" at startup and "Could not write bytes: broken pipe" at shutdown. However research on these errors did not yield answers to my particular issue. Comparing Xorg.0.log (successful boot) and Xorg.0.log.old (black screen), and reading the answers to similar problem, it seems that I might have a X driver issue. However the system worked flawlessly since lately. Additional info on my system : ACER AO722 C62kk Operating system : 3.2.0-31-generic ubuntu Edit : I made a fresh install of Xubuntu 12.04 x64, the issue is still there ... (I have a separate /home so config. files were not erased). Edit 2 : I followed troubleshooting blank screen, so my new observations are without quiet and splash in grub : When the system boots normally, the screen goes black after grub then lights up and displays text information then goes to login screen. (After that the desktop starting time vary substantially, which is new and may be a separate issue ?). When the boot fails, after grub the screen goes black, lights up, goes black, lights up again and most times goes black again. At this point it responds to Alt+SysReq K by lighting up but no more, and has to be rebooted through Alt+SysReq+ RSEINUB. Thank you for your time and attention in advance ! Thibaud Ruelle

  Read the article

• Strange behavior in networking between 64bit and 32bit

  - by Rob

  I'm having a strange behavior about my network setup. I have 2 laptops, one (Lenovo) with Windows 7 Professional 64-bit and another (Acer) with Windows 7 Ultimate 32-bit and a wireless router. I'm connecting these 2 using the router but with a strange behavior. I can ping both machines, as well as the router, but when i try to access their shared folders (\\computer_name\shared_folder) the connection starts to fail and I need to reboot both machines to get it working again. But this only happens sometimes, sometimes it works.

  Read the article

• How to run installation CD for second monitor?

  - by dobsoft

  I am running ubuntu 14 off of a live USB. I have a second monitor that I would like to use while using ubuntu. It has an installation cd that you have to install before using, and when I click on the .exe file the Archive Manager tries to open it and says an error occurred while loading the archive. Thanks for the help. Edit: additional information It just doesn't show up when when I'm in the display settings area. I press the locate(name is probably something else) monitor button too. I know it needs the CD because when I was using it with Windows it didn't work until I went through the installation process on the CD. If ubuntu doesn't use .exe files is there a way to use the CD still? Monitor info from label: -acer LCD monitor -model number: S200HQL Version: S200HQL bd I connect it to my computer using a VGA cord which is connected to a j5create VGA to USB adapter. Not sure if this helps: VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) lsusb output: Bus 002 Device 004: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 002 Device 005: ID 0bc2:2100 Seagate RSS LLC Bus 002 Device 007: ID 0711:5200 Magic Control Technology Corp. Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 1bcf:2c18 Sunplus Innovation Technology Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Blank screen after Switch User or Resume

  - by matt wilkie

  About half the time when I switch users or resume from standby or resume the screen goes blank (black). If I work the cursor keys I can hear the system bell when it gets to the end of the user list. I can also successfully login, going from memory, but screen stays black. Sometimes closing and re-opening the lid will light up the screen again. Pressing the special Function key to enable/disable external monitor connection has no effect [Fn]-[F5],[Fn]-[F6]. If none of the previous work I need to put the computer into hibernation or full power off to restore screen function. If I watch closely when switching users I think I can see the screen initially start to light up and then quickly fade to black. The computer is an Acer Aspire 3500, model ZL6, running Ubuntu 10.10 installed 2 days ago. No proprietary drivers are in use. I'll provide a list of hardware details as soon as I can figure out how to generate that (didn't there used to be an entry for hardware details under the System menu?). Possibly related questions: No resume after Hibernate or Standby When I resume from suspension - the screen is blank Switch user fails to complete successfully For what it's worth, blank after resume also used to happen occasionally when the laptop was running XP-Home, but nowhere near as often, perhaps 6 or 8 times a year. UPDATE: I found System Administration System Testing and ran the Monitor test. It went very very dark, but the window elements could be discerned, and the whole screen flashed (from very very dark to black). On the third repeat of that same test the screen went to full blaupck and stayed there. Moving the mouse, via touchpad, or touch keys did not wake it up again. I had to close the lid and put the computer into hibernate, and press the power button to restore it. UPDATE2: output of lshw: http://pastebin.com/q7n8676r, lspci: http://pastebin.com/6ujzVK4r UPDATE3: sometimes I can restore the screen by flipping to console 1 with ctrl-alt-F1 and then back to graphical with ctrl-alt-F7.

  Read the article

• SD-CARD reader does not show in ubuntu

  - by shantanu

  I bought Acer asipre 4250. It have built-in SD card reader. But it is not working. Nothing show in /media or fdisk but something in dmesg. dmesg: new high-speed USB device number 3 using ehci_hcd [ 127.396733] scsi5 : usb-storage 2-2:1.0 [ 128.526562] scsi 5:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 128.532512] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 129.008110] ohci_hcd 0000:00:12.0: PCI INT A disabled [ 129.032083] ohci_hcd 0000:00:13.0: PCI INT A disabled [ 129.056411] ohci_hcd 0000:00:16.0: PCI INT A disabled [ 129.338026] sd 5:0:0:0: [sdb] Attached SCSI removable disk [ 129.808328] ohci_hcd 0000:00:14.5: PCI INT C disabled [ 167.728616] usb 2-2: USB disconnect, device number 3 [ 169.872284] ehci_hcd 0000:00:13.2: PCI INT B disabled [ 169.872340] ehci_hcd 0000:00:13.2: PME# enabled fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0006bc6d Device Boot Start End Blocks Id System /dev/sda1 * 2048 48828415 24413184 7 HPFS/NTFS/exFAT /dev/sda2 48828416 50829311 1000448 82 Linux swap / Solaris /dev/sda3 50829312 99657727 24414208 83 Linux /dev/sda4 99659774 625141759 262740993 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 99659776 275439615 87889920 7 HPFS/NTFS/exFAT /dev/sda6 275441664 451221503 87889920 7 HPFS/NTFS/exFAT /dev/sda7 451223552 625141759 86959104 7 HPFS/NTFS/exFAT I found another problem just right now. I format last three drives as EXT4 with disk utility. But they are showing as NTFS/exFAT in fdisk. :-(

  Read the article

• Black stripe appears to the right of the screen, impossible to get rid of

  - by Gabriele Cirulli

  After clicking the "Auto Config" button on my Acer AL2216w screen a stripe appeared on the right of the screen where the screen doesn't "exist" and I can't seem to take the screen viewport back even by using the OCD setting and moving it to the right. The left part of the screen is also hidden and I'm not able to see what's going on there. The PC is connected to the screen through a DVI adapter and a VGA cable. I also use multiple monitors and this is the second monitor. Anyway this seems not to be a related issue, as this used to happen even when I only had a single monitor. I managed to fix this issue once but it was more than two years ago and I can't remember what I did, and out of all of the things I've tried so far (connecting the screen to another PC and performing auto adjustment, switching the cables, etc.) none worked. Here's how it looks: Can anyone help me fix this?

  Read the article

• Picasa installs but is missing in the menu

  - by Swapnil Narendra

  Acer Aspire One Netbook Running Ubuntu Netbook Remix 10.10 (freshly installed) 1 GB Ram 150 GM HDD Space I am trying to install Picasa and when I do, it runs its course telling me that it has been installed. But when I try to look for Picasa to run it, it didnt show in the menu anywhere. I am unable to find Picasa on my system and it says that it has been installed already when I try to reinstall it. I have tried a few things; looked for the key: wget -q -O - https://dl-ssl.google.com/linux/linux_signing_key.pub | apt-key add - .. and then added it. tried the following commands after adding Picasa to my source list: sudo apt-get upgrade sudo apt-get install picasa and here is what I got: swapnil@iva-swapo-netbook:~$ sudo apt-get install picasa Reading package lists... Done Building dependency tree Reading state information... Done picasa is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded. and when I tried to look for Picasa again.. I couldnt find it. So I am unable to install Picasa on my system. Please help. (I am also running this thread on ubuntu forums and havent got the solution yet so I am now here) tried Jorge's solution and it brought Picasa immediately, however I am unable to keep it in the launcher. There is no such option. All I can see is only 2 options: 1. Wine 2. Quit Still need help to keep it in the menu/launcher !

  Read the article

• how can I fix error: hd0 out of disk?

  - by rux

  I am running Ubuntu 12.04 on a netbook - Acer AS 1410. After a download session, I restarted the computer and it said: error: hd0 out of disk. Press any key to continue... I pressed everything, but it's just frozen there. Any idea what's wrong with it and what I can do to fix it? I haven't been able to run my computer at all since it's frozen like that. Help please! I booted the live cd and ran sudo fdisk -lu into terminal, and here's what it gave me: Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a696263 Device Boot Start End Blocks Id System /dev/sda3 2048 117229567 58613760 5 Extended /dev/sda5 * 71647232 109039615 18696192 83 Linux /dev/sda6 109041664 117229567 4093952 82 Linux swap / Solaris /dev/sda7 4096 71645183 35820544 83 Linux Partition table entries are not in disk order I am somewhat of a beginner in this, so don't know what this means. any ideas? Thanks!

  Read the article

• Wammu - USB Device Name?

  - by Paul

  I'm trying to get to my phone's filesystem through USB in Wammu, but I'm stuck in the configuration wizard when it asks for a USB device name. After about an hour of Internet searching, here are the failed solutions I've already tried, starting with the relevant information returned by lsusb in terminal. lsusb Bus 001 Device 003: ID 12d1:101e Huawei Technologies Co., Ltd. So I tried opening Wammu through sudo wammu in terminal and inputting "/dev/bus/usb/001/003" as the device name, which returns: Error opening device Device /dev/bus/usb/001/003 does not exist! and then "/dev/bus/usb/001/", which returns: Failed to connect to phone Description: Error opening device. Unknown, busy, or no permissions.<br> Function: Init<br> Error code: 2 Another proposed solution was to try "tail -f /var/log/messages" in terminal. But that only returned a "No such file or directory" message. Seemingly relevant dmesg info: [ 4739.716214] usb 1-1: new high-speed USB device number 8 using ehci_hcd [ 4739.854137] scsi9 : usb-storage 1-1:1.0 [ 4740.854416] scsi 9:0:0:0: CD-ROM HUAWEI T Mass Storage 2.31 PQ: 0 ANSI: 2 [ 4740.867051] sr0: scsi-1 drive [ 4740.867806] sr 9:0:0:0: Attached scsi CD-ROM sr0 [ 4740.870464] sr 9:0:0:0: Attached scsi generic sg1 type 5 I don't know why it is coming up as CD-ROM. But there it is. If you haven't noticed already, I'm an absolute beginner when it comes to Linux and terminal. So speaking to me like I'm a three year old is welcome if you can propose a solution. I'm running Ubuntu 12.04 LTS, and the phone is a Huawei U1250. My computer is an Acer Aspire One D250/KAV60. Any help is much appreciated.

  Read the article

• Debian Testing install USB menu does not respond to keyboard

  - by neurolysis

  I'm trying to install Debian Testing onto my Acer Aspire One ZG5 using the testing versions of boot.img and debian-testing-i386-CD-1.iso. I previously installed (two days ago) the latest release of stable, and the boot.img/CD1 from that worked fine, and installed seamlessly. With testing though, the menu does not respond to the keyboard as soon as the menu appears to select Install/Graphical install/Help, etc. I have also tried to boot with an external (USB) keyboard, which again, works fine with the stable version of boot.img/CD1, but not testing. I did some searching and couldn't find anything that looked similar. Any ideas?

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >