Search Results

Search found 2123 results on 85 pages for 'crossover cable'.

Page 23/85 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Unhappy with performance of GBit Ethernet to Fiber converter

  - by Aaron Digulla

  I just bought a TP-Link MC200CM GBit Ethernet (1000-T) to Fiber (1000-SX) media converter. The device works but I'm unhappy with the performance: When connecting my computer over 1000-T (twisted pair, Cat 6, 18meters) with my server, I get a throughput of about 610MBit/s. If I replace the cable with two media converters, I'm left with about 310-315MBit/s (i.e. half the performance). My setup is like this: Computer <- GBit switch <- long cable <- GBit switch <- server Computer <- GBit switch <- MC200CM <- 30m fiber <- MC200CM <- GBit switch <- server Is there a way to improve the performance? Will another MC be faster? Or is that about as much as I can expect with the additional 2 converters?

  Read the article

• Disable (or switch off) a network interface on windows but keep the "plug and play"

  - by Leandro

  I'm looking for a good workaround to do this on Windows 7 and Windows XP: Disable or make ineffective the network interface (ETH, WIFI, any NIC). If the user connect his ETH cable, the network interface enable again. Important Notes to take care: I'm working with wmic on Win7 (through the command line) I'm working with devcon on WinXP (through the command line) I'm specifically working with the .NET Framework 2.0 on C# but this is just for informational purposes. I know that an event won't help me to detect it (if there is a way or workaround to do this I don't know it). The real problem is that when I disable the NIC, I can't know if the user connects his cable or has a wired network. This is why I am looking for a workaround. I'll treat suggestions as answers if no direct answer exists. I'll provide any extra detail necessary.

  Read the article

• Sharing my broadband connection over a router

  - by user1004985

  I have a broadband connection which I can connect to my laptop's ethernet port. If I want to use the same connection on another machine I would have to do it via a router (I dont want to use ICS since it requires both machines to be ON). I have a router but its uplink is a 4p4c pin rather that an 8p8c(RJ45) so my broadband cable wont fit into it. The router I have is ZTE ZXDSL 531B. And the broadband connection I am talking about has an antenna on the rooftop from which an ethernet cable (CAT 5) runs to my PC's LAN port. Is there some way of utilising the LAN ports of the router to achieve what I mentioned above. Please Help

  Read the article

• Is it common to have portable hard drive not recognize?

  - by lamwaiman1988

  I have a bad hard drive which could not be recognized by windows. If windows can recognize it, it could just be pure luck. There are better chance of it being recognize by plugging it at the usb back of the machine, rather than the front one. More interestingly, I have a usb cable which fork itself at one side ( i.e it has 2 heads at one side ). I can plug both heads to the machine and connect the portable hard drive on the other end of the usb cable? Can I get more voltage by doing this? I am guessing the front usb port doesn't have enough power. I am wondering if I buy a new portable usb hard drive, would it have easy read by plugging at the front usb port? I am not sure if I screw up the jumper connecting the front usb ports, but it is okay for other device such as usb stick and mouse.

  Read the article

• How to set WAN side buffers for WRT54GL running Tomato Firmware

  - by Vickash

  I've recently set up a machine running m0n0wall to try and fight buffer bloat and do some traffic shaping. It was more convenient (geographically speaking) to connect the cable modem directly to my old WRT54GL, then pass everything to the m0n0wall machine and have that do the real routing work. It took a bit of work, but it's working pretty well. I have a cable connection. I have m0n0wall set up to utilize only 90% of the specified speed of my subscription, which is fine. But I've noticed that at certain times of the day (possibly when my true bandwidth drops below that 90%), there's more latency if the connection is used heavily, and traffic shaping doesn't seem to work as well. I suspect this is caused by the buffers on the WRT54GL still being unnecessarily large. If the connection is working as expected, they won't get filled, but in times of reduced bandwidth they would. Does anyone know the command I need to execute, on the WRT54GL running Tomato Firmware, to reduce the buffers on the WAN interface to the minimum size possible?

  Read the article

• Fried graphics card, how to proceed ?

  - by user19496

  Motherboard: Biostar TPower I45 I fried my graphics card (white smoke), by removing the cable marked PCI-E from the card, and then booting. Removed the graphics card, and now the machine is booting, and I can ping it. However I have no possibility to see what is actually happening, because I can't attach a monitor. Can I workaround the lack of monitor in some way, just to see if the motherboard is fine, attach a cable and telnet in or any other way ? Or, do I have to buy and install a new graphics card to be sure ?

  Read the article

• Windows 7 can't connect to via ethernet to Airpot Extreme

  - by Mr AJL

  I have an Airport Extreme, and everything works beautifully on the Mac, but my Windows 7 computer, which is connected via a regular ethernet cable, can't see any network. The Windows computer says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Or do I need to install that Airport utility something on the PC just to connect to the router? (Haven't tried because the PC has no CD drive)

  Read the article

• 59 vs 60 hertz on external display via DisplayPort

  - by Shiki

  Don't know if this is a really specific question or you'll help me out. Please do. I just bought a DeLock DisplayPort cable for my Lenovo T500. Tried to use it with the in-built Intel MHD4500, no use. With the ATI HD3650 (you can switch between the two vga on this machine) I get a normal picture, but only on 59hz. On 60 I get a smaller desktop size (strange). Any idea what can cause this? Will I have any problem if I use the 59hz? (Was using the display with a VGA cable but I get a blurry picture with that (dont matter what device I attach, VGA is like this on this display) and thats why I wanted to change.)

  Read the article

• Computer disappeared from Workgroup

  - by Moayad Mardini

  I've a LAN that has 8 computers running Windows XP and only one (Computer A) running Windows Server 2003. When computer A boots, it shows up in all computers' Workgroups, but after 15-30 minutes, it disappears from the Workgroup in all computers, including itself. However, files can still be transferred from and to A via full path shortcuts and network drive maps still work. I don't know if this has anything to do with the problem or not, but if that particular computer is turned on while the LAN cable is plugged in, it doesn't connect to the network, but it connects if the cable is plugged in after the computer is run. Any tips why this is happening? Thanks.

  Read the article

• Motorola SBG6850 / Linksys WRT54G network problem

  - by user96407

  I am trying to resolve issues with connecting my desktop and LAN capable printer to my network. I recently upgrade to the Motorola Cable Modem Gateway SBG6580 and have TWC coming into it, this works great for wired and wireless connectivity. Although, I am unable to connect to my device from this modem gateway. So, I am trying to cable a Linksys WRT54G (firmware 4.21.4 build 0) to the backside of the SBG6850 so I can use my printer on my network from both my wired desktop and wireless devices. I am pulling wireless off of the SBG6580 and do not want to change this. I have disable the wireless feature on the Linksys WRT54G at this moment. Can someone please help me through this dilemma? I am open to both wired and wireless solutions, but please tell me which approach your sharing in the first line of your response. Cheers!

  Read the article

• Anytime I upload something, my internet slows down extremely. What can I do?

  - by Earlz

  Title says it all. For a bit more info though: Basically, I have Time Warner cable internet. My speeds maintain a stable 2Mbit/s upload and 20Mbit/s download with average ping times around 30ms. This crazy thing happens though when I upload anything. I went to upload a 200M file to my server today through sftp and my internet completely choked up. I speed tested it during this upload and my ping time was around 800ms, download speeds of 0.2Mbit/s and Upload speeds of 0.3Mbit/s. Note, I wasn't downloading anything during this time either. It is just straight upload. What is it that causes this phenomenon? My router is OpenBSD. Is there anything I could set up to fix this problem(by queues or some such), or is this a problem with cable internet?

  Read the article

• Digital audio input on Macbook?

  - by Ken

  I have: a Macbook (not Pro), don't know the exact model but it's a Core 2 Duo 2.0GHz and probably what Wikipedia calls the "Late 2006" or "Mid 2007" model a DVD player, region-free, that has "Coax and TosLink optical digital audio outputs" I want to make an MP3 of the audio track of some DVDs (for learning a new language), and I can't use the Macbook's built-in DVD drive because it's a different region (ugh!). I'm sure I can connect the DVD player to the Macbook with an analog audio cable. However, if it's possible I'd prefer to keep the signal digital. I'm not even positive if my old Macbook has digital audio in, and if so what I need to connect to it. (I've done plenty of home audio geeking, but always in analog!) Will a "Toslink cable" plus a "Toslink Female to Mini-Plug Male Adapter" (found on Amazon) let me connect my things together? It looks like the pieces will fit but I'd like to hear someone confidently knowledgeable on the matter before I buy something. Thanks!

  Read the article

• Why is my router assigning the wrong address via DHCP

  - by Barry

  I have a WRT54G router that is set up to serve out addresses via DHCP. It correctly serves up addresses to every other machine on the network, including another PC, my macbook when connected via wireless, my wife's notebook, and our printer. However, whenever I attach my macbook to the router via an ethernet cable, the address it is given via DHCP is wrong. My local network is set up as 192.168.1.*. However, when my macbook connects with an ethernet cable, it is given the IP 192.168.29.*. Currently, I have the macbook set up with a manual IP address, and all seems to be working fine. Any ideas on what could be causing this?

  Read the article

• Connect a 2.5" (laptop hard disk) SATA hard disk to Desktop PC

  - by Lawliet

  Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) I bought a all-in-one Modex-to-SATA power adapter and SATA cable and I still don't know what to do. I have read various forums and a lot of people are stating that it's perfectly ok, but some are scaring me that by connecting it so, it fried their hard disk. And some also mentioned cutting the yellow 12V wire if I'm planning to use Modex-to-SATA power. Thanks in advance

  Read the article

• Connect a 2.5" (laptop hard disk) SATA hard disk to Desktop PC

  - by Lawliet

  Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) I bought a all-in-one Modex-to-SATA power adapter and SATA cable and I still don't know what to do. I have read various forums and a lot of people are stating that it's perfectly ok, but some are scaring me that by connecting it so, it fried their hard disk. And some also mentioned cutting the yellow 12V wire if I'm planning to use Modex-to-SATA power. Thanks in advance

  Read the article

• HOw to give static ip to router from window XP LAN

  - by Captain Planet

  I have the USB modem internet connection. I am using ICS sharing in XP to share my internet connection. ON window XP LAN i have set up the LAN IP as 192.168.137.1 255.255.255.0 Now i have joined the cable from that XP LAN to another LAPTOP running vista Now if set the LAN on VISTA to get ip automatically them internet don't work but if manually set the ip to 192.168.137.3 255.255.255.0 gateway 192.168.137.1 Then my internet works But i want to join that LAN cable from XP to rouer so that i can use router to divide internet. But i don't know how i can give static ipto router because i think somehow that LAN on XP is not giving the IP address

  Read the article

• Why does eth0 show an IP if I'm booting into runlevel 1?

  - by banjer

  I'm having some issues with networking on a new Linux server I'm building. The OS is SLES 11. When booting into runlevel 1, I see that eth0 is showing an IP. Physically, there is a network cable plugged into the card associated with eth1, and then there is a network cable plugged into a QLogic iSCSI card (eth4, not shown). I've been troubleshooting this for awhile, and it seems like eth0 is somehow getting assigned an IP, even though it isn't configured in Linux or even plugged into the network for that matter. Thoughts? ifconfig -a Here is the ifconfig output (Sorry, I need more rep before I can post images on SF...)

  Read the article

• Serial port access errors in WINE

  - by goldenmean

  Hello, I have a setup in which I use a USB serial adapter + some application which sends and receives data using that serial usb. But this setup which works on a Windows, or even in a VMWare Virtual windows, does not work under WINE. IT transmits data but i cannot receive data. The cable and the applications are same as in the working and non-working scenarios. I guess The fact that the application works over the USB serial cable just as fine under Virtual Windows(VMware running on linux) by mapping /dev/ttyUSB to the com port, no external software/DLL needed, means it does not need any specific driver. (Am I correct in this assumption that application doesnt need any driver?) (I also tried with a different setup(different USB serial adapter + different application under WINE, but even that does not work under WINE, but it works fine under WIndows/Virtual Windows) How can I get it working under WINE? Any pointers appreciated.

  Read the article

• Edimax wireless router is not providing DNS services correctly

  - by Nathan Fellman

  I have an Edimax router that is set up to connect to the internet via L2TP on cable, and on the LAN side it's set up as a DHCP server. The DHCP server gives correct IP addresses, but it sets itself up as the DNS server. However, it doesn't provide the DNS service. I am sure that it's a problem with the router, because I have two computers on the network with the same problem. I see that on the WAN side it gets correct DNS addresses from the ISP, so I'd expect the router to either pass these addresses through to the DHCP clients, or to serve the DNS requests itself by forwarding them to the ISP's DNS. However, it apparently does neither, and there is no DNS. I switched from ADSL to cable last week. On ADSL it connected using PPPoE, and the DNS worked fine. What can be the problem here?

  Read the article

• Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

  - by techaddict

  Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

  Read the article

• please demystify the 10Gb ethernet interfaces, cables

  - by maruti

  this really is a Dell question but tempted to ask the experts @ serverfault. choosen a Dell powerconnect 8024 10GbE switch. per the spec sheet this has 10GbaseT ports. "24x 10GBASE-T (10Gb/1Gb/100Mb) with 4x Combo Ports of SFP+ (10Gb/1Gb) or 10GBASE-T" the HBA on my storage server has 10G CX4 copper ports Dell does not sell any cables and this adds to my confusion. from the picture Dell 8024 seems to have RJ-45 type ports on the front panel? my question: is it a RJ-45 + CX4 cable or CX4 + CX4 cable?

  Read the article

• How can I stop my laptop display from flickering when I connect my TV?

  - by Lord Torgamus

  I have a laptop with an HDMI output port running Vista, and an HDTV with HDMI input ports. The laptop is set to extend its desktop onto a second monitor. When I connect the computer to the TV with an HDMI cable, my laptop screen usually flickers rapidly. Most of the time it lasts for about 30 seconds, but sometimes it lasts for several minutes and once in a while it doesn't happen at all. It wouldn't be so bad except that the cursor moves back to the center of the laptop screen with each flicker, so I can't really do anything until the machine decides it's ready to calm down. I haven't been able to find any pattern at all for the causes or duration of the flickering. It doesn't seem to matter what programs the laptop is running when I connect it to the TV, whether I enable the extended display before or after I connect the TV or which HDMI port/cable I use. What could be causing this, and how can I make it go away?

  Read the article

• Cabling: What to keep in stock?

  - by pehrs

  I have worked a few different places, each one with a different solution, so I would like to hear your suggestions and ideas. I am looking at a situation with multiple server-rooms. We have a mixture of copper (both ethernet and telephone), multi-mode fibre and single-mode fibre. We have all types of connectors: RJ-11, RJ-45, LC, SC, FC, SMA and several I probably forgot about. We have a lot of people working in the area, and keeping track of cables is turning into a full time job. So, here are a the questions: What types and lengths of cable do you keep in stock on site? Do you make your own or buy pre-made? Adapters? Dampeners? How do you manage cable inventory? How do you label the cables? Any other tricks to stop this from driving me crazy?

  Read the article

• USB to USB CD ROM emulator

  - by JohnnyLambada

  I'm wondering if anyone knows of a CDROM emulator that runs on Linux. I want to emulate this configuration: [CDROM DRIVE]----USB CABLE----[COMPUTER UNDER TEST] Where [COMPUTER UNDER TEST] is a computer that boots from a physical CD inserted into the [CDROM DRIVE]. Only instead of the [CDROM DRIVE] I want the following configuration: [CD IMAGE BUILD MACHINE]-----USB CABLE-----[COMPUTER UNDER TEST]. I want to build an ISO image on the [CD IMAGE BUILD MACHINE] and have some sort of USB CDROM emulator running on it to serve up the ISO image to the [COMPUTER UNDER TEST] as though it was talking to the [CDROM DRIVE]. Does this exist? If it does, I can't find it. I want to do this so I can test out bootable CDs without burning a lot of coasters.

  Read the article

• Can't access some websites with any browser

  - by Charles Kingsmill

  I'm running Windows 7 64-bit on a new Samsung laptop and accessing the internet okay via ethernet cable to my university's ISP. Some sites work fine (e.g. google.com) but I can't access others at all (microsoft.com, topshop.com). I can't connect to those sites in safe mode with networking. And ping and tracert both fail. There's no proxy. Other users can connect successfully to these sites using my cable and socket. I've tried all the following with no success: using various browsers (IE9, FF, Chrome) creating a new user updating drivers clearing the DNS cache using OpenDNS and Google's DNS turning off Avast tweaking the MTU running MS malicious software removal tool running Spybot S&D reviewing the hosts file disabling the IPv6 options repairing / resetting winsock settings disabling advanced javascript options I have run out of ideas... can anyone see anything I've missed??!

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >