Search Results

Search found 2230 results on 90 pages for 'gateway'.

Page 23/90 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Routing a PPTP client and VMware Server instance running on the same box

  - by servermanfail

  I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

  Read the article

• How to find ip address of my Asus RT-AC86U in Access Point mode?

  - by WilliamKF

  I'm using an Asus wireless router model RT-AC68U and can connect fine to the internet using it wirelessly. I configured the router to be an Access Point, but having done so, I can no longer locate the GUI to adjust the router as I have no idea what its IP Address is anymore. The router is plugged into a cable modem and router which is a model SMCD3G is a business class gateway labeled Comcast Business IP Gateway. This gateway is assigning ip addresses in the range 10.1.10.XX and I went to the web interface at 10.1.10.1 and listed the connected devices and see my laptop which is connected to the Asus access point along with a few other devices, but none of the devices listed are the Asus router (I tried all the six ip addresses listed). How can I determine the IP Address of my Asus router in access point mode so I can see the GUI interface again to control the router other than by doing a factory reset?

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• NAT rules betweek 2 network interfaces (with iptables)

  - by Simone Falcini

  this is the current network that I have: UBUNTU: eth0: ip: 212.83.10.10 bcast: 212.83.10.10 netmask 255.255.255.255 gateway 62.x.x.x eth1: ip: 192.168.1.1 bcast: 192.168.1.255 netmask: 255.255.255.0 gateway ? CENTOS: eth0: ip: 192.168.1.2 bcast: 192.168.1.255 netmask 255.255.255.0 gateway 192.168.1.1 I basically want this: Make specific NAT rules from the internet to specific internal servers depending on the port: Connections incoming to port 80 must be redirected to 192.168.1.2:80 Connections incoming to port 3306 must be redirected to 192.168.1.3:3306 and so on... I also need one NAT rule to allow the servers in the subnet 192.168.1.x to browse the internet. I need to route the requests on eth0 to eth1 to be able to exit to internet. Can I do this on the UBUNTU machine with iptables? Thanks!

  Read the article

• Windows 2008, 2 NICS, routing problem

  - by Srodriguez

  Dear all, I've some questions regarding basic routing, can't seem to relate to other questions posted in this site. My architecture: Windows 2008 server with 2 nics in the server. NIC1: IP 10.198.6.xxx, submask 255.255.252.0, gateway 10.198.4.xxx NIC2: IP 192.168.168.xxx, submask 255.255.255, no gateway defined both NICS are just connected to two separate switches, with other computers. I want to be able that all the requests that have a destination of 192.168.168.xxx are redirected to the NIC2, all the other to the NIC1. I know it's possible to do it with the route command, but normally we have to specify a gateway? (route ADD 192.168.168.0 MASK 255.255.255.0 ???) How can this be archived? Thanks a lot for your help!

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• OpenVPN Configuration - Windows 7 client & debian server

  - by Guillaume

  I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

  Read the article

• Virtualizing Firewalls/UTM

  - by TheD

  So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

  Read the article

• How to connect two subnet with Windows Server?

  - by 9dan

  Hello, I have some work to do in a small office. This office has two separate Internet connections. One is a kind of DSL line and connected through the Internet sharing router (DHCP). One is a leased line with public IP adresses (No DHCP). This leased line provide only 30 IP addresses and the gateway is provided by the ISP. Some workers use private IP provided by the router, some workers use manually setup public IP. There is a Windows 2008 R2 server with two NICs, connected to each lines. I want to connect/merge(?)/bridge(?) two subnet with this server so that users from the different subnet can access each other. How can I accomplish this? Something like, add gateway function to this server and public IP users change the gateway to point this server.. It it possible ? Sorry for my rambling. Thanks in advance.

  Read the article

• Using PVLANs with normal VLANs in a trunked environment

  - by user974896

  Assume a trunked environment with two switches, S1 and S2. The swtiches are connected with a trunk port designed to pass VLAN 26. What would happen if VLAN 26 on S2 is configured as a private-vlan with the default gateway and DHCP server and default gateway as promisc ports. What if S1's VLAN 26 is configured as a standard VLAN. Would the hosts on S1 be able to communicate with the promisc ports on S2? Would they be able to communicate with the hosts on S2? To further complicate things what if the DHCP server were to reside on S1 and I wanted S2 to have private VLANS with promisc ports as the gateway and DHCP server while still leaving S1 in a standard vlan configuration.

  Read the article

• Superscope DHCP leases and configuration set up

  - by Vdub

  Hello I wanted to see if someone could help with a network problem I am having. Right now we have a super-scope and scopes of 192.168.50.1 and 192.168.51.1, as of now both are activated but only 192.168.50.1 is handing our leases, 192.168.51 wont. here is a summary of our network Gateway: watchguard firebox x750e for our router/gateway at 192.168.50.1 I set up as a secondary IP address 192.168.51.1 Server: Server 2008 r2 standard, running our DNS @ 192.168.50.242 and 8.8.8.8 as a secondary, AD, and DHCP. On that NIC card i have 192.168.50.242 as the IP address and 192.168.51.242 as a secondary. 192.168.50.1 as the default gateway and 192.168.51.1 as a secondary. Im am not very knowledgeable at this but as far as i have researched after adding a super scope and activating scopes, they should automatically start handing out addresses and I cant figure out why only one does. any help at all would be appreciated.

  Read the article

• Windows 7 with two network cards doesn't route traffic

  - by Tomek

  I have simple task to do: I have wni7 with two nics.I want to connect another comp(osx) to win7 through second nic to connect it to internet. I already changed the registry. Win7 interface with 192.168.2.1 has no gateway set (no point to do that) OSX interface with 192.168.2.2 has gateway set to 192.168.2.1 I do not add any routes on win7, every thing seems to be already there network on second nic is detected as "undefined network" (probably effect of no gateway) i can achieve any connectivity to internet from OSX only by enabling network connection sharing on nic with 192.168.2.1, but it enables NAT and I'm interested only in pure routing without nat(it's a setup for some research). firewall is off. It seems to me that win7 refuses to forward packets for some reason. Perhaps "undefined network" and NLA service is to blame, although i couldn't find any info about that. Below ascii schematics of my setup: internet<--router(192.168.1.1)<--(192.168.1.1) WIN7 (192.168.2.1)<--(192.168.2.2)OSX Thanks

  Read the article

• Routing based on source address in Windows Server 2008 R2

  - by rocku

  I'm implementing a direct routing load balanced solution using Windows Server 2008 R2 as back-end server. I've configured a loopback interface with the external IP address. This works, I am receiving packets with the external IP address and respond to them appropriately. However our infrastructure requires that traffic which is being load-balanced should go through a different gateway then any other traffic originating from the server, ie. updates etc. So basicly I need to route packets based on source address (external IP) to another gateway. The built-in Windows 'route' command allows routing based on destination address only. I've tried setting a default gateway on the loopback interface and mangled with weak/strong host send/receive parameters on the interfaces, however this didn't work. Is there any way around this, possibly using third party tools?

  Read the article

• Laptop connectd to 2 VPNs (1st for Internet over WiFi, 2nd to access shared folders on another network) is failing to route traffic over 2nd VPN

  - by Triynko

  I set up a VPN on Windows Server 2008 through its routing and remote access services. I connected to the VPN, and configured the client to allow for split tunneling (Internet traffic goes to my default gateway, and traffic directed to the VPN server goes through the VPN gateway). I had to adjust the routing table, adding an entry to ensure traffic to my VPN server goes through the tunnel by running the command "route add [VPN.IP] mask 255.255.255.255 [VPN.GATEWAY.IP] IF [VPN_INTERFACE_#]". Adding the correct route makes everything work flawlessly on all my machines, except for one. The problematic machine is a laptop that's not directly connected to a network. It connects to WiFi, and then connects to a VPN to obtain internet access. Finally, it connects to the target VPN server for file sharing. The "route add" trick doesn't work for that laptop, I'm assuming because it's connected to two VPNs, and I'm getting the routing wrong. Can anyone familiar with routing explain what routes I may need to add?

  Read the article

• PPTP VPN Server issue : server = centOS & client = windows 7

  - by jmassic

  I have a CentOS server configured as a PPTP VPN Server. The client is a Windows 7 with "Use default gateway on remote network" in advanced TCP/IPv4 properties enable. He can connect to CentOS without any problem and can access to: The Box of his ISP (http://192.168.1.254/) The CentOS server The website which is hosted by the server (through http://) But he canNOT access any other web service (google.com or 74.125.230.224) I am a beginner with web servers so I do not know what can cause this problem. Note 0 : The Windows 7 user must be able to access the whole internet through the CentOS PPTP proxy. Note 1 : With "Use default gateway on remote network" in advanced TCP/IPv4 UNCHECKED it is the same problem Note 2 : With "Use default gateway on remote network" in advanced TCP/IPv4 UNCHECKED AND "disable class based route addition" CHECKED the Win 7 can access google but with the ISP IP (no use of the VPN...) See Screenshot Note 3 : I have made a echo 1 > /proc/sys/net/ipv4/ip_forward and a iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

  Read the article

• how to stop deferred emails

  - by Will K

  I have a postfix mail gateway. At the same time, every other host is set to use this gateway as the relay. We have some automated outgoing emails sent from some hosts. I believe the gateway trys to send a deferred status back to the system started this. But that system is a null client, which sends but not receive any email Is there anyway to stop sending the deferred status? e.g. postfix/smtp[35725]: 2F6A155C256: to=, relay=none, delay=260862, delays=260862/0.01/0/0, dsn=4.4.1, status=deferred (connect to orange.mydom.com[192.168.1.5]:25: Connection refused) Thanks

  Read the article

• Connecting Linux to WatchGuard Firebox SSL (OpenVPN client)

  Recently, I got a new project assignment that requires to connect permanently to the customer's network through VPN. They are using a so-called SSL VPN. As I am using OpenVPN since more than 5 years within my company's network I was quite curious about their solution and how it would actually be different from OpenVPN. Well, short version: It is a disguised version of OpenVPN. Unfortunately, the company only offers a client for Windows and Mac OS which shouldn't bother any Linux user after all. OpenVPN is part of every recent distribution and can be activated in a couple of minutes - both client as well as server (if necessary). WatchGuard Firebox SSL - About dialog Borrowing some files from a Windows client installation Initially, I didn't know about the product, so therefore I went through the installation on Windows 8. No obstacles (and no restart despite installation of TAP device drivers!) here and the secured VPN channel was up and running in less than 2 minutes or so. Much appreciated from both parties - customer and me. Of course, this whole client package and my long year approved and stable installation ignited my interest to have a closer look at the WatchGuard client. Compared to the original OpenVPN client (okay, I have to admit this is years ago) this commercial product is smarter in terms of file locations during installation. You'll be able to access the configuration and key files below your roaming application data folder. To get there, simply enter '%AppData%\WatchGuard\Mobile VPN' in your Windows/File Explorer and confirm with Enter/Return. This will display the following files: Application folder below user profile with configuration and certificate files From there we are going to borrow four files, namely: ca.crt client.crt client.ovpn client.pem and transfer them to the Linux system. You might also be able to isolate those four files from a Mac OS client. Frankly, I'm just too lazy to run the WatchGuard client installation on a Mac mini only to find the folder location, and I'm going to describe why a little bit further down this article. I know that you can do that! Feedback in the comment section is appreciated. Configuration of OpenVPN (console) Depending on your distribution the following steps might be a little different but in general you should be able to get the important information from it. I'm going to describe the steps in Ubuntu 13.04 (Raring Ringtail). As usual, there are two possibilities to achieve your goal: console and UI. Let's what it is necessary to be done. First of all, you should ensure that you have OpenVPN installed on your system. Open your favourite terminal application and run the following statement: $ sudo apt-get install openvpn network-manager-openvpn network-manager-openvpn-gnome Just to be on the safe side. The four above mentioned files from your Windows machine could be copied anywhere but either you place them below your own user directory or you put them (as root) below the default directory: /etc/openvpn At this stage you would be able to do a test run already. Just in case, run the following command and check the output (it's the similar information you would get from the 'View Logs...' context menu entry in Windows: $ sudo openvpn --config client.ovpn Pay attention to the correct path to your configuration and certificate files. OpenVPN will ask you to enter your Auth Username and Auth Password in order to establish the VPN connection, same as the Windows client. Remote server and user authentication to establish the VPN Please complete the test run and see whether all went well. You can disconnect pressing Ctrl+C. Simplifying your life - authentication file In my case, I actually set up the OpenVPN client on my gateway/router. This establishes a VPN channel between my network and my client's network and allows me to switch machines easily without having the necessity to install the WatchGuard client on each and every machine. That's also very handy for my various virtualised Windows machines. Anyway, as the client configuration, key and certificate files are located on a headless system somewhere under the roof, it is mandatory to have an automatic connection to the remote site. For that you should first change the file extension '.ovpn' to '.conf' which is the default extension on Linux systems for OpenVPN, and then open the client configuration file in order to extend an existing line. $ sudo mv client.ovpn client.conf $ sudo nano client.conf You should have a similar content to this one here: dev tunclientproto tcp-clientca ca.crtcert client.crtkey client.pemtls-remote "/O=WatchGuard_Technologies/OU=Fireware/CN=Fireware_SSLVPN_Server"remote-cert-eku "TLS Web Server Authentication"remote 1.2.3.4 443persist-keypersist-tunverb 3mute 20keepalive 10 60cipher AES-256-CBCauth SHA1float 1reneg-sec 3660nobindmute-replay-warningsauth-user-pass auth.txt Note: I changed the IP address of the remote directive above (which should be obvious, right?). Anyway, the required change is marked in red and we have to create a new authentication file 'auth.txt'. You can give the directive 'auth-user-pass' any file name you'd like to. Due to my existing OpenVPN infrastructure my setup differs completely from the above written content but for sake of simplicity I just keep it 'as-is'. Okay, let's create this file 'auth.txt' $ sudo nano auth.txt and just put two lines of information in it - username on the first, and password on the second line, like so: myvpnusernameverysecretpassword Store the file, change permissions, and call openvpn with your configuration file again: $ sudo chmod 0600 auth.txt $ sudo openvpn --config client.conf This should now work without being prompted to enter username and password. In case that you placed your files below the system-wide location /etc/openvpn you can operate your VPNs also via service command like so: $ sudo service openvpn start client $ sudo service openvpn stop client Using Network Manager For newer Linux users or the ones with 'console-phobia' I'm going to describe now how to use Network Manager to setup the OpenVPN client. For this move your mouse to the systray area and click on Network Connections => VPN Connections => Configure VPNs... which opens your Network Connections dialog. Alternatively, use the HUD and enter 'Network Connections'. Network connections overview in Ubuntu Click on 'Add' button. On the next dialog select 'Import a saved VPN configuration...' from the dropdown list and click on 'Create...' Choose connection type to import VPN configuration Now you navigate to your folder where you put the client files from the Windows system and you open the 'client.ovpn' file. Next, on the tab 'VPN' proceed with the following steps (directives from the configuration file are referred): General Check the IP address of Gateway ('remote' - we used 1.2.3.4 in this setup) Authentication Change Type to 'Password with Certificates (TLS)' ('auth-pass-user') Enter User name to access your client keys (Auth Name: myvpnusername) Enter Password (Auth Password: verysecretpassword) and choose your password handling Browse for your User Certificate ('cert' - should be pre-selected with client.crt) Browse for your CA Certificate ('ca' - should be filled as ca.crt) Specify your Private Key ('key' - here: client.pem) Then click on the 'Advanced...' button and check the following values: Use custom gateway port: 443 (second value of 'remote' directive) Check the selected value of Cipher ('cipher') Check HMAC Authentication ('auth') Enter the Subject Match: /O=WatchGuard_Technologies/OU=Fireware/CN=Fireware_SSLVPN_Server ('tls-remote') Finally, you have to confirm and close all dialogs. You should be able to establish your OpenVPN-WatchGuard connection via Network Manager. For that, click on the 'VPN Connections => client' entry on your Network Manager in the systray. It is advised that you keep an eye on the syslog to see whether there are any problematic issues that would require some additional attention. Advanced topic: routing As stated above, I'm running the 'WatchGuard client for Linux' on my head-less server, and since then I'm actually establishing a secure communication channel between two networks. In order to enable your network clients to get access to machines on the remote side there are two possibilities to enable that: Proper routing on both sides of the connection which enables both-direction access, or Network masquerading on the 'client side' of the connection Following, I'm going to describe the second option a little bit more in detail. The Linux system that I'm using is already configured as a gateway to the internet. I won't explain the necessary steps to do that, and will only focus on the additional tweaks I had to do. You can find tons of very good instructions and tutorials on 'How to setup a Linux gateway/router' - just use Google. OK, back to the actual modifications. First, we need to have some information about the network topology and IP address range used on the 'other' side. We can get this very easily from /var/log/syslog after we established the OpenVPN channel, like so: $ sudo tail -n20 /var/log/syslog Or if your system is quite busy with logging, like so: $ sudo less /var/log/syslog | grep ovpn The output should contain PUSH received message similar to the following one: Jul 23 23:13:28 ios1 ovpn-client[789]: PUSH: Received control message: 'PUSH_REPLY,topology subnet,route 192.168.1.0 255.255.255.0,dhcp-option DOMAIN ,route-gateway 192.168.6.1,topology subnet,ping 10,ping-restart 60,ifconfig 192.168.6.2 255.255.255.0' The interesting part for us is the route command which I highlighted already in the sample PUSH_REPLY. Depending on your remote server there might be multiple networks defined (172.16.x.x and/or 10.x.x.x). Important: The IP address range on both sides of the connection has to be different, otherwise you will have to shuffle IPs or increase your the netmask. {loadposition content_adsense} After the VPN connection is established, we have to extend the rules for iptables in order to route and masquerade IP packets properly. I created a shell script to take care of those steps: #!/bin/sh -eIPTABLES=/sbin/iptablesDEV_LAN=eth0DEV_VPNS=tun+VPN=192.168.1.0/24 $IPTABLES -A FORWARD -i $DEV_LAN -o $DEV_VPNS -d $VPN -j ACCEPT$IPTABLES -A FORWARD -i $DEV_VPNS -o $DEV_LAN -s $VPN -j ACCEPT$IPTABLES -t nat -A POSTROUTING -o $DEV_VPNS -d $VPN -j MASQUERADE I'm using the wildcard interface 'tun+' because I have multiple client configurations for OpenVPN on my server. In your case, it might be sufficient to specify device 'tun0' only. Simplifying your life - automatic connect on boot Now, that the client connection works flawless, configuration of routing and iptables is okay, we might consider to add another 'laziness' factor into our setup. Due to kernel updates or other circumstances it might be necessary to reboot your system. Wouldn't it be nice that the VPN connections are established during the boot procedure? Yes, of course it would be. To achieve this, we have to configure OpenVPN to automatically start our VPNs via init script. Let's have a look at the responsible 'default' file and adjust the settings accordingly. $ sudo nano /etc/default/openvpn Which should have a similar content to this: # This is the configuration file for /etc/init.d/openvpn## Start only these VPNs automatically via init script.# Allowed values are "all", "none" or space separated list of# names of the VPNs. If empty, "all" is assumed.# The VPN name refers to the VPN configutation file name.# i.e. "home" would be /etc/openvpn/home.conf#AUTOSTART="all"#AUTOSTART="none"#AUTOSTART="home office"## ... more information which remains unmodified ... With the OpenVPN client configuration as described above you would either set AUTOSTART to "all" or to "client" to enable automatic start of your VPN(s) during boot. You should also take care that your iptables commands are executed after the link has been established, too. You can easily test this configuration without reboot, like so: $ sudo service openvpn restart Enjoy stable VPN connections between your Linux system(s) and a WatchGuard Firebox SSL remote server. Cheers, JoKi

  Read the article

• In-Application Support Made Easier

  - by matt.hicks

  With the availability of Oracle UPK 3.6.1 and Enablement Service Pack 1 for Oracle UPK 3.6.1 (Oracle Support login required for both), there are quite a few changes for content admins to absorb. In addition to the support added for dozens of application releases, patches and new target applications, we've also added features to make implementing and using In-Application Support even easier. First, the old Help Menu Integration Guides have been updated and combined into a single In-Application Support Guide. If you integrate UPK content for user assistance, or if you're interested in doing so, read the new guide! It covers all the integration steps, including a section on the new In-Application Support Configuration Utility. If you've integrated content in multiple languages, or if you've ever had to make configuration changes for UPK Help Integration, then you know how cumbersome it was to manually edit javascript files. No longer! The Player now includes a configuration utility that provides a web browser interface for setting all In-Application Support options. From the main screen, you see a list of applications covered by the published content. Clicking on an application name takes you to the edit configuration screen where you can set all Player options for that application. No more digging through the Player folders to find the right javascript file to edit. No complicated javascript syntax to make changes. And with Enablement Service Pack 1 we've added a new feature we're calling the Tabbed Gateway. The Tabbed Gateway is a top-level navigation bar for Help Integration. And all tabs, links, and text are controlled with the Configuration Utility... I think the Tabbed Gateway is a really cool and exciting feature for content launch. I can't wait to hear how your ideas for how to use it for your content. Let me know in comments or email!

  Read the article

• CloudMail

  - by kaleidoscope

  In Web Applications, we often come across requirement of sending and receiving emails through our application. So same can be for the applications hosted on Azure. So Do you want to send email from an application hosted on Azure? CloudMail is one of the possible answers. CloudMail is designed to provide a small, effective and reliable solution for sending email from the Azure platform directly addressing several problems that application developers face. Microsoft does not provide an SMTP Gateway (yet) so the application is forced to connect directly to one hosted somewhere else, on another network. So to implement such functionality one of the possible option is using Free email providers. This might be fine for testing, but do you really want to rely on a free service in production? There can be other issues with this approach like if your chosen SMTP gateway is down or there are connection problems? Again there can be some specific requirement that, you want to send email via a company’s mail server, from inside their firewall. CloudMail solves these problems by providing a small client library that you can use in your solution to send emails from you application and a Windows Service that you run inside your companies network that acts as a relay. Because the send and relay are disconnected there are no lost emails and you can send from your own SMTP Gateway.   CloudMail is in its Beta version and available for download here.   Technorati Tags: Geeta,Azure Email,CloudMail

  Read the article

• Sharing an internet connection through the Ethernet port

  - by Bob Cunningham

  I have a small living room PC (Bohica, running fully-updated Ubuntu 10.10/Maverick) connected to my HDTV that I use for web browsing and media streaming. It connects via WiFi (wlan0) to my Fedora server (Snafu) that in turn connects to the internet. I use static addressing, and everything has been working fine. I just got a Blu-ray player, and I'd like to give it wired network access to the internet via Bohica's available wired ethernet port (eth0). So far, I haven't been to get eth0 and the network configured to get the Blu-ray player talking to the internet. Here's my wlan0 configuration: ip4 addr: 192.168.0.100 mask: /24 (255.255.255.0) gateway: 192.168.0.4 (fedora box) The Blu-ray player is set to an IP of 192.168.0.98/24, with the same gateway as above. I want eth0 set to an IP of 192.168.0.99/24, but when I do this using nm-connection-editor I lose internet access (the system tries to use eth0 as the default internet access interface). How do I get my blu-ray player to talk to the internet through Bohica, and do so without disrupting my current (working) network? Thanks. Edit: Here's the relevant output from nm-tool with the Blu-ray player connected: $ nm-tool NetworkManager Tool State: connected - Device: eth0 Type: Wired Driver: forcedeth State: disconnected Default: no HW Address: 90:FB:A6:2C:94:32 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on - Device: wlan0 [wlan0] Type: 802.11 WiFi Driver: ndiswrapper State: connected Default: yes HW Address: 00:26:5A:C0:D0:05 IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.4

  Read the article

• Lost connectivity after configuring multiple network adapters on separate networks

  - by Dave Long

  I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

  Read the article

• symfony/zend integration - blank screen

  - by user142176

  Hi, I need to use ZendAMF on a symfony project and I'm currently working on integrating the two. I have a frontend app with two modules, one of which is 'gateway' - the AMF gateway. In my frontend app config, I have the following in the configure function: // load symfony autoloading first parent::initialize(); // Integrate Zend Framework require_once('[MY PATH TO ZEND]\Loader.php'); spl_autoload_register(array('Zend_Loader', 'autoload')); The executeIndex function my the gateway actions.class.php looks like this // No Layout $this->setLayout(false); // Set MIME Type $this->getResponse()->setContentType('application/x-amf; charset='.sfConfig::get('sf_charset')); // Disable cause this is a non-html page sfConfig::set('sf_web_debug', false); // Create AMF Server $server = new Zend_Amf_Server(); $server->setClass('MYCLASS'); echo $server->handle(); return sfView::NONE; Now when I try to visit the url for the gateway module, or even the other module which was working perfectly fine until this attempt, I only see a blank screen, with not even the symfony dev bar loaded. Oddly enough, my symfony logs are not being updated as well, which suggests that Synfony is not even being 'reached'. So presumably the error has something to do with Zend, but I have no idea how to figure out what the error could be. One thing I do know for sure is that this is not a file path error, because if I change the path in the following line (a part of frontendConfiguration as shown above), I get a Zend_Amf_Server not found error. So the path must be correct. Also if I comment out this very same line, the second module resumes to normality, and my gateway broadcasts a blank x-amf stream. spl_autoload_register(array('Zend_Loader', 'autoload')); Does anyone have any tips on how I could attach this problem? Thanks P.S. I'm currently running an older version of Zend, which is why I am using Zend_Loader instead of Zend_autoLoader (I think). But I've tried switching to the new lib, but the error still remains. So it's not a version problem as well.

  Read the article

• Issues printing through ssh tunnel and port forwarding

  - by simogasp

  I'm having some problems trying to print through a ssh tunnel. I'd like to print from my laptop to a network printer (Toshiba es453, for what matters) which is in a local network. I can reach the local network using a gateway. So far I did the following: ssh -N -L19100:<Printer_IP>:9100 <username>@<ssh_gateway> Basically i just mapped the port 19100 of my laptop directly to the input port of the printer, passing through the gateway. So far, so good. Then, i tried to install on my laptop a new printer with the GUI config tool of ubuntu, so that the new printer is on localhost at port 19100 (as APP Socket/HP Jet Direct) , then I provided the proper driver of the printer. In theory, once the tunnel is open I should be able to print from any program just selecting this printer. Of course, it does not work. :-) The document hangs in the queue with status Processing while in the shell where I set up the tunnel I get these errors on failing opening channels debug1: Local forwarding listening on ::1 port 19100. debug1: channel 0: new [port listener] debug1: Local forwarding listening on 127.0.0.1 port 19100. debug1: channel 1: new [port listener] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Connection to port 19100 forwarding to 195.220.21.227 port 9100 requested. debug1: channel 2: new [direct-tcpip] debug1: Connection to port 19100 forwarding to 195.220.21.227 port 9100 requested. debug1: channel 3: new [direct-tcpip] channel 2: open failed: connect failed: Connection timed out debug1: channel 2: free: direct-tcpip: listening port 19100 for 195.220.21.227 port 9100, connect from ::1 port 44434, nchannels 4 debug1: Connection to port 19100 forwarding to 195.220.21.227 port 9100 requested. debug1: channel 2: new [direct-tcpip] channel 3: open failed: connect failed: Connection timed out debug1: channel 3: free: direct-tcpip: listening port 19100 for 195.220.21.227 port 9100, connect from ::1 port 44443, nchannels 4 channel 2: open failed: connect failed: Connection timed out debug1: channel 2: free: direct-tcpip: listening port 19100 for 195.220.21.227 port 9100, connect from ::1 port 44493, nchannels 3 debug1: Connection to port 19100 forwarding to 195.220.21.227 port 9100 requested. debug1: channel 2: new [direct-tcpip] As a further debugging test I tried the following. From a machine inside the local network I did a telnet <IP_printer> 9100, got access, wrote some random thing, closed the connection and correctly I got a print of what I had written. So the port and the ip of the printer should be correct. I tried the same from my laptop with the tunnel opened, the telnet succeeded but, again, the printer didn't print anything, getting the usual channel x: open failed: errors. I'm not a great expert on the matter, I just thought that in theory it was possible to do something like that, but maybe there is something that I didn't consider or I did wrong. Any clue? Thanks! Simone [update] As further debugging test, I tried to replicate the procedure from a machine in the local network. From that machine, I did ssh -N -L19100:<IP_printer>:9100 <username>@<ssh_gateway> (note that now the machine, the gateway and the printer are in the same local network) then I tried again the telnet test with telnet localhost 19100, I got access and everything, but I didn't get the print but the usual error channel 2: open failed: connect failed: Connection timed out Maybe I am missing some other connection to be forwarded or maybe this is not allowed by the administrators. Of course, if I connect via ssh tunneling to the local machine from my laptop through the gateway, I can successfully print using the lpr command (from the local machine). But this is what I would like to avoid (yes, I'm lazy...:-), I would like to have a more 'elegant' and transparent way to do that.

  Read the article

• ssh tunneling with visualsvn

  - by DeveloperChris

  I have been asked to setup visualsvn for visual studio 2008 Due to firewall restrictions and server configuration. I need to use ssh tunneling. My problem is this. The local machine needs to connect to a gateway machine via ssh then connect to the subversion server so Local machine ---{ssh}--- gateway ---{ssh}-- subversion server I am not exactly sure of the correct process to do this. It appears that I must start a ssh process using plink to open a local port and forward that to the remote subversion server. eg: plink user@gateway -L 22:192.168.1.1:22 Then when visualsvn starts it uses tortoiseplink to make the actual connection through to the subversion server using svn+ssh://username@localhost:22/myrepo This seems very very clunky. firstly it needs several steps to setup the connection secondly I need plink running which leaves a command prompt on the desktop (clutter = yuck) lastly I need to use two different programs that do the same thing. (plink + tortoiseplink) The problem is that tortoiseplink doesn't run in the background. As soon as I connect to the ssh gateway and enter the password it closes again. So I can't use it to create the initial connection. If I use plink instead of tortoiseplink in visualsvn then I never get prompted for the password. so it just hangs with an open command prompt and no password request. Is there a way to setup visualsvn so that everything happens in one command line? I have searched high and low for a suitable and clean method to tunnel from visualsvn to the remote server and have found very little. it all either assumes one hop (not two like mine) or it glosses over all the hard bits. DC

  Read the article

• Routing audio from GSM module to a Bluetooth HandsFree device

  - by Shaihi

  I have a system with the following setup: I use: Windows CE 6 R3 Microsoft's Bluetooth stack including all profiles Motorola H500 The Audio Gateway service is up and running (checked through services list in cmd) GSM Module is functional - I am able to set outgoing calls and to answer calls. Bluetooth is functional - the A2DP profile plays music to Motorola headphones (can't remember the model right now) I want to hold a conversation using a headset device. I have included all Bluetooth components in the catalog. I pair the device using the Control Panel applet. When I press the button on the Motorla device to answer a call I get a print by the Audio Gateway: BTAGSVC: ConnectionEvent. BTAGSVC: SCOListenThread_Int - Connection Event. BTAGSVC: ConnectionEvent. BTAGSVC: SCOListenThread_Int - Connection Event. BTAGSVC: ConnectionEvent. BTAGSVC: A Bluetooth peer device has connected to the Audio Gateway. BTAGSVC: Could not open registry key for BT Addr: 2. BTAGSVC: The peer device was not accepted since the user has never confirmed it as a device to be used. So my questions are as follows: What do I need to do to pair the device with the Audio Gateway? Once my device is paired, do I need to set anything else up? (except for the GSM module of course)

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >