Search Results

Search found 11524 results on 461 pages for 'insurance networking news'.

Page 23/461 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• How can I auto-connect to a WPA2 Enterprise network?

  - by Demetri

  I would like my computer to automatically connect to a WPA2-Enterprise network as soon as it boots whenever the network is available, without any action needed by me. The computer already offers to connect, and even remembers the password, but I must still hit 'Enter' to connect. Also, connection does not occur if my login is at the terminal. I would like to automatically connect every time I login, no matter how I do so, unless a more preferred network is available. What is the best way to do this? I am running Fedora 19. A shell script that can be invoked at the terminal would be preferred. Connecting even if the Gnome-desktop has not launched is a must.

  Read the article

• DD-WRT (WRT54G) and (THOMSON TG782) how to put them togather?

  - by FeRtoll

  Ok so let me explain, i bought WRT54G and successfully installed DD-WRT v24-sp1 (07/26/08) mini-special - build 9994. That's all ok no problems with it all normal functioning. And just to add (i don't need wireless, wireless is turned off always) What i want: ISP's router (TG782) from it's INTERNET port(out) cable "which was before in my pc" is connected to WRT54G's INTERNET port and then from WRT54G LAN port 1 to my pc. The problem: How do i connect and setup all? I have tried many times on many different ways but cant get it to work IF THE CABLE FROM TG782 IS CONNECTED TO WRT54G ON INTERNET PORT. If i connect the TG782 to Lan port 1 on WRT54G and my pc to lan port 2 then all works fine after i setup gateway and all. But i want to connect TG782 to Internet port of WRT54G because i need "Access Restrictions" and this only goes through WAN right? please correct me if i am wrong. What i have tried: This is how i have tried to setup all. The TG782 router ip is 192.168.1.1 And WRT54G ip is 192.168.1.30 so in WRT54G control panel i have setup like this: ----WAN Connection Type---- Connection Type: Automatic Configuration - DHCP STP: Disabled ----Router IP---- Local IP Address: 192.168.1.30 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 (the TG782) ----Network Address Server Settings (DHCP)---- DHCP Type: DHCP Server Start IP Address: 192.168.1.100 Maximum DHCP Users: 6 And this wont work i probably miss something more, if anyone can help i would be thankfull. Also i have to note that i have tried to set my network adapter on pc to use the gateway of WRT54G and ip 192.168.1.102 In short: i cant get it to work normal only as a switch! Thanks for any help! -------EDIT:------- Here is an image which maybe can help: http://img27.imageshack.us/img27/4227/allin1w.jpg

  Read the article

• Wi-Fi connected but can't go to any site

  - by Michael Dy

  My Windows 7 laptop can connect to our Wi-Fi signal, I can sign in on Yahoo! Messenger, but I can't go to any site. I can access the Net on other devices. The issue started a few weeks ago, so I've been troubleshooting since then in vain. There's no virus, and I already used System Restore. In Wireless Network Connection Status, the received activity is greater than the sent activity. I turned off Windows Firewall and still no Net access. My ping tests: How do I fix this?

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

• Error while bringing up eth1

  - by mhay

  I'm getting this error while bringing up my network card: (process:2550): WARNING **: _nm_object_get_property: Error getting 'State' for /org/freedesktop/NetworkManager/ActiveConnection/3: (19) Method "Get" with signature "ss" on interface "org.freedesktop.DBus.Properties" doesn't exist I'm using the following commands: 1. ifup eth1 2. /etc/init.d/network restart I have installed a fresh copy of Centos 6.2 and configured the network card.

  Read the article

• Which one should I choose: gateway or router?

  - by Jader Dias

  My router allows me to choose between gateway and router (RIP1/RIP2). Which is the best option and why?

  Read the article

• How do I set up a shared internet on a network using computer hooked up to a router

  - by Skadlig

  I got a wireless broadband modem (Huawei E1750) hooked up to my computer (call it A., running Windows-7) whose internet I wish to share to my other computer (call it B., also running Windows-7). A. is hooked up to my d-link DIR-600 router using a wired connection to port 1 on the router. B. is connected to the router using a wireless connection. Now I have tried setting up the sharing according to the help files for ICS but I have not been able to get it working. I suspect that there is something in my hardware configuration that is making it difficult. I would appreciate some tips and pointers as to what could be the reason to my problems.

  Read the article

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• How to remap IPs visible from local machine to IPs visible from a machine I have SSH access to?

  - by gooli

  I'm so far out of my depth I don't even know what to google for. There's a server I can connect to via SSH. Via that server I can access other server on its subnet via SSH. What I want to do is be able to access the machines that server has access to directly. Say the server IP is 192.168.7.7 and is the only one in the 192.168.x.x range I have access to. I'd like to configure things in such a way that when I to access say 192.168.7.100 on my machine, the connection will go through an SSH tunnel I open to 192.168.7.7 and out to 192.168.7.100. I would like this to work for any port if at all possible. I know I can set an HTTP proxy and even a SOCKS proxy, but I'm wondering is there is a way to actually remap some of the IP my machine sees to IP only visible from the remote machine. What would this configuration be called? IS this NAT, VPN, IP2IP or something else? How can I set up this on a Windows client box that connects via SSH to a Linux box? Sounds to me like I need to set up some kind of filtering on the network driver or possibly a virtual NIC, but I'm not sure where to go next.

  Read the article

• Wireless is not currently enabled

  - by ikartik90

  I have a HP Pavilion TX2000 tablet PC with me with windows 7 OS running on it. I used to access the Internet using my D-Link DIR 615 wireless adapter on the tablet and it used to work quite fine until one day, when I hibernated my Windows 7, the wireless went off and the problem seems to persist even after my hard efforts to clear it. I checked if the router works fine, and yes it did as my iPod was still catching wireless signals on the other hand, when I checked mu device manager, I realized that I now had no wireless driver. I checked on HP's website for one, but ironically even they didn't have wireless drivers meant for my tablet for Windows 7. Please help me find a solution to this problem. Further queries will be entertained as frequently as possible. Thanks.

  Read the article

• Slow network file transfer (under 20KB/s) on newly built x64 Win7

  - by Mangoshake

  I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

  Read the article

• What do I need to do to set my computer as Default Gateway?

  - by Vaibhav

  We are trying to put together a box with dual LAN cards (let's say Outer and Inner), where the Inner LAN card is supposed to act as a default gateway on the network it is connected to. This box is running Ubuntu. The basic purpose for this box is to take messages generated on the inner network, do some work with them and forward them out the Outer LAN card to a server. The inner network is completely isolated with simply a regular switch connecting the Inner LAN Card with two other boxes. These other boxes either throw out multi-cast messages (which the Inner LAN Card is listening to), or send out unicast messages meant for the server which is not on this inner network. So, we need the Inner LAN Card to act as a default gateway, where these unicast messages will then be sent, and the code on the dual-LAN Card box can then intercept and forward these messages to the server. Question: 1. How do we setup the LAN Card to be default gateway (does it need some configuration on Ubuntu)? 2. Once we have this setup, is it a simple matter of listening to the interface to intercept the incoming messages? Any help (pointers in the right direction) is appreciated. Thanks.

  Read the article

• wireless network with cable modem and access point

  - by hayri

  I have a Scientific Atlanta EPC2203 cable modem and a TP-Link TL-WA500G access point. When I connect my computer directly to modem with a CAT5e cable I have internet connection on my laptop (when i type ipconfig i see my external ip there, provided by isp). So I decided to have wireless network in the flat, allowing other devices to connect as well. I bought this wireless ap (TL-WA500G) configured Wireless security stuff, and connected it to my modem. With that configuration (by default AP has static ip of 192.168.1.254) only my computer can connect to internet over wifi, but not any other device. When I set the IP of AP to Dynamic IP (DHCP) it is the same. How should I change my configuration to enable all wifi devices to connect to internet?

  Read the article

• server and user directly connected no pinging...

  - by jtzero

  I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

  Read the article

• Two Routers - 1 Port Straight to First Router

  - by apples

  At my house we have two Wifi routers one's connected directly to the modem and the other is plugged in down stairs as a second network(Directly connected to the first router) Is there a way that I could make it so that I have the second router have its own network, but have one or two ports that would act as if they were directly connected to the first router? That way I can port forward to devices on the second router. Here are the information about the routers: Router 1 - Linksys WRT54G Running stock firmware Router 2 - Linksys E900 Running Tomato Firmware So to summarize what I'm asking is how would I have two networks from two routers but be able to connect directly to the first router through one of the ports on the second router. Here's a Visio Drawing of what I would like to look like

  Read the article

• Long access time for static web page on virtual machine

  - by Karol

  My setup Windows 7 on workstation that I use at work (with domain) and home (no domain) Virtual machine (VMWare) that runs Arch Linux (I will call it just "Linux") with network interface in bridged mode. Linux serves web pages with Nginx. IP address of Linux machine is 192.168.0.16 and is added to C:\windows\system32\drivers\etc\hosts: 192.168.0.16 bridged bri IP address of Windows workstation is added to /etc/hosts: 192.168.0.10 workstation I can add more details to my setup description (I am not sure what is relevant). The question Often (but not always) it takes long time for a web browser (Firefox) to open static web page served by Linux. I am sure it is not a performance issue. To be more specific: it takes about ~20 seconds to resolve(?) the address http://bridged for a web browser. Additionally I have just installed samba service and noticed similar problem, so it is not specific to browser & http. Initial access for samba shares also takes long time.

  Read the article

• My NetGear router suddenly started showing limited access for all wifi connected laptops

  - by Yasser

  I have netgear n300 router which I had installed about 6 months back. Here is how the setup is, I have a local internet provider by the name of "Hathway" they have this modem which is in turn connected to the router and a wire from router is connected to my desktop. As shown in this pic below, except for the laptop I use a desktop rest all the connection is same So with this connection and the below configuration, every thing worked fine. The desktop would work also all my laptops and mobile devices would connect and be able to access the internet without any problem. Now suddenly since yesterday (with no changes made whatsoever to this config) all my laptops start showing the limited connection message and cannot connect to the internet. However the desktop which is connected can access the internet. Can someone please guide me on this.

  Read the article

• cisco ePC 3208 router and captive portal

  - by Dejan Milosevic

  Ok, i have cisco ePC 3208 router, and cable internet goes in router via cable and router is emiting wireless. It can work without computer and it is working fine. Now i want to have capiteve portal with home page for my buisness and user logins. Is it possible that i use computer as gateway for captive portal, so when user goes to wireless it will redirected to computer local server for authorization and then passed by if user and pass is good, or i need another router or wifi acess point?

  Read the article

• Set default wireless adapter

  - by Evan Kroske

  I just acquired a Wi-Fire long-range wi-fi adapter, and I would like to test it with my Ubuntu desktop computer. However, my machine defaults to using a built-in wireless card. How can I set my new wireless adapter as the default wireless connection? How can I disable my internal wireless card (without opening my computer case)?

  Read the article

• Can't communicate with Primary DNS Server

  - by horsley

  A computer, with Windows 7, can't access any website by domain suddenly. Whether this computer use a wired link or connect to the WLAN, The fault persists IP and DNS obtained automatically, and seems normal (ipconfig /all return the correct info) I can visit websites by using HTTP proxy The DNS server is available, other computer in my room works properly. I can ping myself, the gateway and any other IP, but domains I can use nslookup and obtain the correct IP info There are some error information in the event log about dns client events explaining the client can not verify the DNS server available Windows network diagnosis explain that Windows can't communicate with the device or resource (Primary DNS Server) I guess the dns client should be blame. I tried to do the following things but the fault persist. Reinstall the driver of network adapter Reset TCP/IP (netsh int ip reset) Reset Winsock (netsh winsock reset) Reset LSP I don't want to reinstall the whole os, what should I do?

  Read the article

• Can I bridge two wired networks with a Netgear WG602 (v4)

  - by Mr. Flibble

  I have two networks and I want to join them. Only one has a router. The other is currently just a bunch of computers joined via a switch. So it looks a little like this: 1. Router + comp1 + comp2 + wireless ap 2. comp3 + comp4 + Netgear WG602 Is it possible to use the WG602 to connect to the WIFI of the main network (the one with the router) and connect via wire to the 2nd network - therefore allowing the computers on network 2 to use the router on network 1?

  Read the article

• File sharing from a cable connected pc to wifi connected laptop (windows 7 ultimate)

  - by Aiden Jones

  I have a one desktop running windows 7 ultimate connected to Ethernet cable. And I want to share folder to another wifi connected laptop (also windows 7 ultimate). Both machines are on the same home internet connection. I have tried to share folders by going to properties sharing advanced sharing permissions checked all the boxes to allow all but I don’t see any shared files on my laptop. I know it’s possible to share folders between two Wi-Fi connected machines but how can it be done when one pc is cable connected and other is Wi-Fi connected on the same internet connection.

  Read the article

• Windows periodically disconnects, reconnects to the network

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

  Read the article

• Setting up a WPA-PSK network card to connect to a WPA2 network

  - by mattshepherd

  I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

  Read the article

• 5GHz vs 2.4GHz dual band router, max mbps

  - by Tallboy

  I've done a fair amount of reading before posting this but there are a few things still unclear. I just bought a Netgear WNDR3700 N600. I understand that 5GHz offers more channels, less interference because of more available channels, wont interfere with a microwave and so on, and also has a shorter range. Currently, my router is broadcasting both signals (for my iPhone on 2.4, and my computer on 5) But my question is What is the max speed of 5GHz in mbps? In the router settings, it allows me to set '300mbps', but I keep reading online that the max is 54. Is this true? I noticed when I set up the router the default for 2.4 was set to 300 and the default for 5 was set to 54, so I changed both to 300. Is this fine as well? I don't see why it wouldn't be maxed out for both by default. On the box it says max rate of 300+300 so I assume this is correct, but it's throttled down so the router isn't stressing in case you have something streaming media 24/7 and slowing the internet down too. What is the max range of 5GHz? my apt is 780 square feet, and the router is in the main living room.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >