Search Results

Search found 45894 results on 1836 pages for 'super'.

Page 234/1836 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

  • Why Both 8GB USB Flash Drives Have Different Integrities?

    - by Boris_yo
    USB 3.0 SuperTalent Express DUO 8GB recently had its partition corrupted and declared itself "write-protected" and I was told in chat by @sidran32 that this usually means that flash drive gone bad due to writing cycles limit being reached. Having this thumbdrive for over a year being used infrequently, I was in doubt and referred to SuperTalent's support. I was given recovery tool which I executed but it failed first time prompting me to reinsert it. After that, I formatted it with Windows 7 integrated format utility since recovery tool offered to do this as well which was successful. The problem as I have noticed is with integrity of SuperTalent: Compare above to SanDisk's Micro Cruzer 8GB: Am I missing something? Both thumbdrives are of 8GB and have same FAT32 file system.

    Read the article

  • IIS8 behind a VPN + Windows Server 2012 - how to properly bind IP+Port

    - by ryugen
    This is my first question so I hope I'm going to give you enough information. I'm running Windows Server 2012 within the Hyper-V environment of my Windows 8 machine. Within Windows Server 2012 I'm running a VPN tool based on openVPN to hide my real IP. When I run IIS8 with the VPN disconnected it works flawlessly through the Internet (port 80 forwarded correctly). But as soon as I connect to the VPN I can't reach my site through the domain anymore. Now I tried basically everything I know which is why I'm asking you guys. I tried binding IIS8 to the IP of my virtual ethernet card. I tried changing the priority of the NIC through the "Network and sharing center" via the advanced tab. I used ipconfig /flushdns in case there was something wrong in the DNS handling. Hell, I even turned off the Windows firewall. I also used a port scanner to verify the problem. The webserver is reachable on port 80 with VPN disconnected and immediately gets unreachable on connect. Theoretically both IPs (my regular one AND the VPN) should be reachable or at least not impair the other one right? Do you have any other suggestion? Do I have to route something somewhere somehow?

    Read the article

  • I can't uninstall Git

    - by Tom
    I was researching Git so I downloaded the Windows version to test it out on a repository on GitHub. After about 30 minutes I couldn't work out how to use it, so I decided I probably wouldn't need a distributed repository as our projects aren't that big and went back to what I know - SVN. (I thought) I uninstalled all the Git related stuff I'd put on my PC, but have now got an irritating problem where if I open any folders I get an error message saying: Hello [ERROR] Could not find git path As you can imagine, this is a real pain, does anyone have any ideas on how to fix it?

    Read the article

  • Uninstalled programs cleaner

    - by ldigas
    Generally, I'm looking for a recommendation for an uninstalled programs cleaner ? What is it ? You have a program, you uninstall it, and it leaves a bunch of crap on your machine, starting from registry entries, to shortcuts that lead nowhere, up to a bunch of no more used files in Program Files and so ... Registry cleaners usually do some of this stuff, but 'twas wondering, what are good tools that have it all in one package ? I know such tools exist, 'cause in the past I've met with a few. Only I didn't need them then ;)

    Read the article

  • Samsung printer (ML-1640) margin problem

    - by Rytis
    I just got a new laser printer, Samsung ML-1640, and it has once again confirmed my experience that Samsung printers suck badly. The printer prints fine, except that the top margin is set at random, usually very small, cutting text on the top of page off. I tried updating firmware, getting new drivers, but nothing helped. I tried changing paper types, and it seemed that with the paper set as "plain" it was OK, but I just tried printing again after letting the printer rest for the night, and wasted 6 pages until I managed to print 2 boarding passes... Is there anything else I could try to resolve the issue?

    Read the article

  • Apache error "No address associated with hostname" on Arch Linux (ZMLarch)

    - by Eedoh
    I'm trying to set up video surveillance system using IP cameras and ZoneAlarm on Arch Linux. I set up fixed IP address, I've managed to get streams from cameras, etc. However, after restart of the machine, I cannot start Apache again. I checked configuration of rc.conf, and saw that static IP configuration has been deleted, and also secondary nameserver in resolv.conf. Tried to re-write these with correct parameters, but now with no effect. This is tail of my /var/log/httpd/error_log file, after /etc/rc.d/httpd restart attempt [Fri Jan 29 04:20:45 2010] [alert] (EAI 5) No address associated with hostname: mod_unique_id: unable to find IPv4 address of "zmhost" Configuration failed Anybody have an idea on how could I fix this?

    Read the article

  • Dual mode 802.11n PCI adapters

    - by Mike Thompson
    I have recently bought a DLink DIR-825 router. It is a dual mode (2.4GZ & 5GHZ) 802.11n wireless access point/router. What is a good PCI adapter to pair with it? DLink appear to only make one dual mode adapter, which is the DWA-160 USB adapter. They don't seem to have a PCI adapter in their range, which seems very strange. Do any of the other network manufacturers make a good dual mode adapter?

    Read the article

  • I have too many DNS servers configured

    - by Jon Will
    I have my laptop connecting to my wireless router, and I have told the router to issue out DNS via the DHCP lease. The laptop is configured to use the information. The router is configured to only issue two DNS server addresses from open dns, but the laptop reports Networking Dns Servers: 10.197.100.1 10.197.100.2 10.197.100.3 8.8.8.8 8.8.4.4 208.67.222.222 208.67.220.220 I have no idea where the laptop is getting these additional IPs as DNS. Please advise.

    Read the article

  • SuSE always logs a user in TVM session

    - by rohan
    Hello all, I recently installed Suse Linux enterprise Desktop 11 on my box. I created an user and logged in first time into a GNOME session without any problems. Last time I logged in I selected the session as TWM and that got me into the T windows manager just fine. Now when I log out and try to log back into a GNOME session, it will still log me into the TVM session. I have tried restarting the box but that has not helped. However, when I remote log in to the machine it will let me got on the GNOME session just fine. I'm guessing this is probably a really simple fix, however I am a Linux newbie and doing a google search isn't yielding me what I'm looking for. Thanks in advance for your help, Rohan

    Read the article

  • Recovering OS X Mail Accounts Lost in Crash

    - by Tim
    I had a hard crash on my Mac PowerBook and when I restarted, Mail came up with only my MobileMe account still available and I cannot figure out how to restore the other eight email accounts I have. The directories in ~/Library/Mail all seem to be there. I even did an rsync of the modified .plist files from a TimeMachine backup of the directory from before the crash (unfortunately, I was on travel, so the backup is more than a week old and I'd like to try and recover from that point without having to entirely restore from TimeMachine). I also did a fix permissions. So my questions are where exactly is the account information for Mac Mail kept? Any thoughts of what might have caused the failure? Why does only MobileMe come up? Any other thoughts on how to fix things?

    Read the article

  • Basic networking problem with Ubuntu 9.04 on Acer Extensa 5635Z laptop

    - by sapporo
    I just installed Ubuntu 9.04 on a brand new Acer Extensa 5635Z laptop, but ethernet networking does't work (wireless doesn't work either, but I'd be happy with ethernet for now). eth0 isn't listed in /etc/network/interfaces: $ cat /etc/network/interfaces auto lo iface lo inet loopback lshw does show the nic, but I can't make much sense out of the information: $ sudo lshw -class network -sanitize *-network DISABLED description: Wireless interface product: AR928X Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:07:00.0 logical name: wmaster0 version: 01 serial: [REMOVED] width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath9k latency=0 module=ath9k multicast=yes wireless=IEEE 802.11bgn *-network UNCLAIMED description: Ethernet controller product: Attansic Technology Corp. vendor: Attansic Technology Corp. physical id: 0 bus info: pci@0000:09:00.0 version: c0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list configuration: latency=0 *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: [REMOVED] capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes Thanks for your help!

    Read the article

  • How to format new HDD windows XP

    - by c0mrade
    I just bought new SATA 1TB Baracuda HDD, I inserted and my windows didn't recognize it. Because I didn't have any other OS or anything to format it I used Centos i386 installation to format it. I of course disconnected my original disk from the motherboard and formatted it using CENTOS.. but now when I come back to the windows I can't format this HDD. Its recognized as RAW. What can I do to make it work?

    Read the article

  • Trimming article length in Google Reader

    - by Dov
    I'm considering switching to Google Reader from Safari's RSS reader. One feature that I would absolutely miss from Safari is its Article Length slider it gives you for each feed, so you can choose to show more or less content. Is there any way to achieve this in Google Reader's Expanded view? PS I also posted this question on Google's Help forum here.

    Read the article

  • RAMDiskVE keeps causing computer to freeze

    - by Steph
    I found this in the Event Viewer logs: The description for Event ID 11 from source RAMDiskVE cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer. Which doesn't say much. The details don't reveal much more: Failed to read configuration information from registry. 0000000002002C00000000000B0007C0000000000000000000000000000000000000000000000000 So my question is, what is RAMDiskVE and what device is it for? Basically I'm trying to rule out hardware but I have no idea what's failing...

    Read the article

  • VLOOKUP and match functions appear to be searching the function rather than value

    - by Brandon S.
    Vlookup and match seem to be searching based on the function I have in my cell rather than the value i have in the cell. I have a column with dates, (ex: C2, which has the formula =E2&"/"&F2&"/"&D2 in them, for example). (where E2, F2, D2 are the year, month, and date). In another sheet and column, I have a bunch of dates, and i'm using the formula =VLOOKUP(C2,'sheet2'!A1:B252,2,FALSE), which doesn't work. (returns #N/A) If I replace C2 with the same date, but without the formula (just typing it in), VLOOKUP works. Why is this?

    Read the article

  • Windows 7 - Add shell command for .png file

    - by Aximili
    On Windows XP, you could go to Folder Options - File Types, select PNG, create a new action, such as this Action: Crush Application: "F:\Programs\PNGCrush\crush.bat" "%1" So you can right click on a .png file and select Crush. How do you do this on Windows 7? I assume through regedit or .reg file, but how? EDIT: Thank you for all your replies... but I'd like to avoid "Open With" or 3rd party program if possible.

    Read the article

  • Apple, Time Capsule: can I use it for servers ?

    - by Patrick
    hi, i was wondering if I can use Time Capsule from a server. Let's say I have an ubuntu server, and I'm running some websites and web applications on it. I would install these appications on ubuntu but then store the "file folders" of each website or application (with images, videos, etc.. ) on Airport capsule and leave only the application files on the server. Is this feasable ? Thanks Patrick

    Read the article

  • Compaq R4000 laptop randomly locking up

    - by Josh
    I have a Compaq R4000 laptop with 2GB of RAM, running Ubuntu Linux 9.10. It is randomly locking up on me, approximately once every two days. I have a second partition with Windows XP Home installed, and I have had the system lock up in XP as well, meaning I believe this is a hardware issue. I have run two passes of Memtest86+ with no errors. The system has a fan that has died, so I initially suspected overheating. However the system just locked up on me while I was in the middle of typing a script to warn me / shut down if the temperature was too high. When the lockup happened the temperature was 88°F, so I am now starting to believe that may not be the issue. When the system locks up, I cannot SSH in nor ping it. Nothing shows in syslog when I reboot. I have configured it to send syslog messages to a local server as well and no messages appear on that server when the lockup happens. I am open to any and all advice!

    Read the article

  • Add subtitles to Ogg Video

    - by Jaxau
    I've started to convert my DVD collection to Ogg Video (OGV) and it works so far quite good. However, I heard that I can embed the subtitles inside the OGV-file as well. How can I do this on Linux? On Windows there are several applications but on Linux not so much. Any examples would be appreciated. Edit: I have the original VOB of course. PS. No, I don't give out my movies. Don't even ask. I paid for them, not you. :)

    Read the article

  • Installing sublime text plugins all at once

    - by James
    Is there a way to install all the sublime text 2 plugins that you would like to install all at once. In Notepad++, there is a plugin manager which lets you install all the plugins you want to install by checking the box next to the plugin name & description. I was wandering if there is something like that for sublime text. For eg, I would like to install Zen Coding, JQuery Package for Sublime Text, Sublime Prefixr, JS Format, SublimeLinter and many other plugins all at once rather than typing each plugin in the Package Control and installing it one by one.

    Read the article

  • Splitting coax cable for PC tuner

    - by TheLakersHighlights
    I have an HDTV connected with HDMI from a DISH Network VIP612 DVR Receiver. I want to split the coaxial connection from the DVR to my Hauppauge 1200 WinTV HVR-850 HDTV Tuner Stick. What splitter and coaxial cable (needs to transmit audio and video) should I get to make this a watchable TV on my computer?

    Read the article

  • Quicksilver doesn't open PDF's like it used to

    - by Niels Bom
    I've been using Quicksilver for a while now but lately I've been getting this problem that QS doesn't show the Acrobat Reader icon when a PDF is selected, but goes to the "Open With" tab. See the screenshot here: http://skitch.com/niels.bom/n8nw5/google-reader-1000 Is this a bug? Or did I somehow bork a preference setting? I'm using QS B54, 3815, which is the latest AFAIK and Mac OS X 10.5.8. Thanks!

    Read the article

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >