Search Results

Search found 20062 results on 803 pages for 'malcolm post'.

Page 238/803 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• How to use webdav and user dir in the same time in the same section ?

  - by Louis

  Dear community, i would like to mount trough webdav my https://myserver/~user_account but not https://myserver/. What i am doing now is : <IfModule mod_userdir.c> UserDir public_html UserDir disabled root <Directory /banonymous/data/home/*/public_html> DAV On AllowOverride FileInfo Limit AuthConfig Options MultiViews SymLinksIfOwnerMatch IncludesNoExec <Limit GET POST OPTIONS> Order allow,deny Allow from all </Limit> <LimitExcept GET POST OPTIONS> Order deny,allow Deny from all </LimitExcept> </Directory> </IfModule> and i am setting the authentification in the .htaccess of eache user. AuthType Basic AuthName "Password Required" AuthUserFile /etc/apache2/users/htpasswd Require User geeky It does not work. Is there someone who can tell me if it is possible ? and if it is how to do it. My dream would have been to put the Dav On in the .htaccess.

  Read the article

• IIS Messing on Wordpress Permalinks or WP's fault?

  - by Jesus Rodriguez

  Hello, I had a problem and after some research I discovered the exactly point where is failing. blog.domain.com Is not working, it says that the page cannot be found (404) blog.domain.com/index.php Working as expected If you click on Home, it will says that the page cannot be found, if you try to preview a new post, it says that the page cannot be found... I can see every post btw. I run my blog on a Windows hosting using IIS. my permalink is this: /index.php/%postname% IIRC I had to use index.php because my IIS doesn't have URL rewriting. I have no problem with the index.php thing on the url, I have now a good SEO and I don't want to change my permalink but I Don't know why is not working now... just from one day to the next... It's a problem of WP or is just my host messing up? If is my blog, do you know what is causing this? (Just for create a concrete ticket about the exactly problem) Thank you.

  Read the article

• Is it possible to rate limit based on host headers? i.e. not just on ip address

  - by Blankman

  I have a web service endpoint that I am building where people will post an xml file to, and it will really get pounded with over 1K requests per second. Now they are sending in these xml files via http post, but a good majority of them will be rate limited. The problem is, the rate limiting will be done by the web application by looking up the source_id in the xml, and if it is over x requests per minute, it will not be processed further. I was wondering if I could do rate limit checking earlier in the processing somehow and thus save the 50K file going threw the pipeline to my web servers and eating up resources. Could a load balancer make a call out to verify rate usage somehow? If this is possible, I could maybe put the source_id in a host header so even the XML file doesn't have to be parsed and loaded into memory. Is it possible to just look at host headers and not load up the entire 50K xml file into memory? I really appreciate your insights as this takes more knowledge of the entire tcp/ip stack etc.

  Read the article

• Tooltips shadow stuck on desktop

  - by faulty

  I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. 1. Turn of aero 2. Hibernate 3. Switch main display to external display and switch back. 4. Change resolution

  Read the article

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• How can I find out which processes on my computer are accessing the microphone?

  - by Vinayak

  After reading this interesting Lifehacker post and reading the comments on the page, one person was wondering if it would be possible to use the Physical Device Object Names of other hardware such as the microphone to find out the names of processes using that device. I tried the same approach, but so far it only seems to work for the webcam. Is there any other way I could get this to work in Process Explorer? UPDATE: The Lifehacker post was about finding out which Windows process is currently using your webcam. This is how they went about doing it: Start Device Manager (WIN+R → "devmgmt.msc" → OK) Find your webcam among the list of devices (check under Imaging Devices) Open the properties window of the device and switch to the Details tab (Right click → Properties → Details) In the dropdown menu, select Physical Device Object Name and copy the string(Right click → Copy) Download Process Explorer Make sure you have opened Process Explorer in Administrator Mode(File → Show Details for All Processes) Hit CTRL+F and enter the string you copied earlier(it should be something like \Device\000000XX) Hit the Search button and you should see a list of processes using the webcam(if there are any)

  Read the article

• Test whether svn REPO changes are reflected in Working Copy

  - by user492160

  Requirement Changes will be made to the REPO directory and this should get updated to wc(working copy) as opposed to the normal way of WC REPO. Senario: My svn repo- /var/www/svn/drupal My checkout-dir/working-copy- /var/www/html/drupalsite So I've done: edited post-commit hook to contain: "/usr/bin/svn update /var/www/html/drupalsite" I won't make any change to svn WC. I'll make changes to svn REPO- /var/www/svn/drupal. After changes are made to svn repo, run "svn commit /var/www/html/drupalsite". This will trigger the post-commit hook. This inturn will run "svn update /var/www/svn/drupal" and thus my WC will get updated with the changes of REPO. Query a. Would the above steps 1-3 help achieve my 'Requirement'? b. I'd need advise on how to test if the above setup works successfully or not. I'm at loss about the success of steps 1-3 the reason why query(a) is present. This is a bit more of a concern for me. NB: I'm new to subversion. Whatever I've configured till now have been done by reading articles online. Reason for query (b) is because I'm not into development. It seems to be a php drupal website and I happen to be setting it up. So I'm not aware as to how to make a "PROPER" change in REPO so that it gets reflected in WC. If reflected, my configs are right and the team can start on development. I manually put a random file/folder into REPO dir for seeing a change in WC and ran steps 1-3 but was of no avail and later on learned that it was NOT the way to make a change to a REPO. Pleas advise. Thanks

  Read the article

• How do I apply multiple subnets to a server with one NIC?

  - by Cosban

  I am trying to route multiple IPs through one physical NIC on my dedicated server for use with Proxmox KVM VMs. I have a dedicated server which is currently running Debian 4.4.5-8 with 3 available ip addresses for use, which will be displayed as 176.xxx.xxx.196 (main), 176.xxx.xxx.198 (on same subnet as main) and 5.xxx.xxx.166 (different subnet). I am currently trying to route the third IP address with the dedi for use with a vps that I have set up using proxmox v2.x but am having a really, really hard time doing so. Virtual interfaces binding the additional IP addresses work as expected, ruling out external routing problems. The provider has given the following information for the IP addresses on the main subnet: gateway: 176.xxx.xxx.193 netmask: 255.255.255.224 broadcast: 176.xxx.xxx.223 As well as the following information for the IP address on the second subnet: gateway: 5.xxx.xxx.161 netmask: 255.255.255.248 broadcast: 5.xxx.xxx.167 Everything I've tried with /etc/network/interfaces has either not worked, or has rendered the network completely useless. This is the current state of the file, which has the secondary IP address working on the same subnet as well as IPv6 working, but not the second subnet. # Nativen IPv6 Schnittstelle iface eth0 inet6 manual # Bridge IPv4 Schnittstelle (176.xxx.xxx.193/27) auto vmbr0 iface vmbr0 inet static address 176.xxx.xxx.196 netmask 255.255.255.224 gateway 176.xxx.xxx.193 broadcast 176.xxx.xxx.223 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 176.xxx.xxx.198/27 dev vmbr0 auto vmbr1 iface vmbr1 inet static address 5.xxx.xxx.166 netmask 255.255.255.248 gateway 5.xxx.xxx.161 broadcast 5.xxx.xxx.167 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 5.xxx.xxx.166/27 dev vmbr1 # Bridge IPv6 Schnittstelle (Reichweite: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx::/64) iface vmbr0 inet6 static address xxxx:xxxx:xxxx:xxxx:xxxx:xxxx netmask 64 up ip -6 route add xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 up ip -6 route add default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0

  Read the article

• SQL Full-Text indexing not populating

  - by Sam

  Hi, We installed a clustered SQL 2005 installation on windows 2008 and reattached our san drives from another machine and restored to do a migration to new hardware. There have been a few minor issues, but this one has me stuck. Trying to populate Full-Text indexes is not working. I create a basic table with some simple text in a new database and get the same results as old indexes. 2010-09-27 10:30:46.85 spid19s Informational: Full-text Full population initialized for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'). Population sub-tasks: 1. 2010-09-27 10:31:15.36 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001DF. Attempt will be made to reindex it. 2010-09-27 10:31:15.37 spid19s The component 'MSFTE.DLL' reported error while indexing. Component path 'D:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\Binn\MSFTE.DLL'. 2010-09-27 10:31:15.37 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001E0. Attempt will be made to reindex it. The rebuild/repopulate procedure finishes, but I get zero rows in the index. The .dll in the message is present and the service accounts have access to this. My FTData also has data in it, so it seems there wouldn't be permission issue on this folder. Application throws this error: “PHP Warning: mssql_query() [function.mssql-query]: message: Full-text catalog 'ikm_PageIndex_FText' is in an unusable state. Drop and re-create this full-text catalog. (severity 16) in E:\Inetpub\knowledgebase_insidemesa\lib\database\mssql.php on line 154” A microsoft discussion is the only post I found which had claimed to fix this - said it was registry related, but then didn't post the fix.

  Read the article

• PHP/MySQL Performance Testing with Just PHP

  - by Mike Gifford

  I'm trying to diagnose a server where the website is loading very slowly, but unfortunately my client has only provided me with FTP access. I've got FTP access so I can upload PHP scripts, but can't set up any other server side tools. I have access to phpMyAdmin, but not direct access to the MySQL server. It is also unfortunately a Windows server (and we've been a Linux shop for over a decade now). So, if I wan to evaluate MySQL & disk speed performance through PHP on a generic server, what is the best way to do this? There are already tools like: https://github.com/raphaelm/php-benchmark or https://github.com/InfinitySoft/php-benchmark But I'm surprised there isn't something that someone has already set up & configured to just run through and do some basic testing of a server's responsiveness. Every time we evaluate a new server environment it's handy to be able to compare it to an existing one quickly to see if there are any anomalies. I guess I'd just hoped that someone else had written up a script to do this already. I know I have, but that was before Github when there was a handy place to post scraps of code like this. Originally posted in http://stackoverflow.com/questions/12321498/php-mysql-performance-testing-with-just-php but it was recommended that I re-post it here.

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• Running Jackd on Ubuntu for my External Firewire Sound card

  - by Asaf

  Hello, I'm running Ubuntu 10.04 and I have an external Sound card: Phonic Firefly 302. I've connected the device, installed Jackd, added the lines: @audio - rtprio 99 @audio - memlock 500000 @audio - nice -10 to /etc/security/limits.conf logged out, logged back in, ran qjackctl (sudo qjackctl to be exact), ran the settings and chose "firewire" on the driver option, pressed "Start" and that was the output: 20:10:19.450 Patchbay deactivated. 20:10:19.578 Statistics reset. 20:10:19.601 ALSA connection graph change. 20:10:19.828 ALSA connection change. 20:10:21.293 Startup script... 20:10:21.293 artsshell -q terminate sh: artsshell: not found 20:10:21.695 Startup script terminated with exit status=32512. 20:10:21.695 JACK is starting... 20:10:21.695 /usr/bin/jackd -dfirewire -r44100 -p1024 -n3 jackd 0.118.0 Copyright 2001-2009 Paul Davis, Stephane Letz, Jack O'Quinn, Torben Hohn and others. jackd comes with ABSOLUTELY NO WARRANTY This is free software, and you are welcome to redistribute it under certain conditions; see the file COPYING for details 20:10:21.704 JACK was started with PID=22176. no message buffer overruns JACK compiled with System V SHM support. loading driver .. libffado 2.0.0 built Mar 31 2010 14:47:42 firewire ERR: Error creating FFADO streaming device cannot load driver module firewire no message buffer overruns 20:10:21.819 JACK was stopped successfully. 20:10:21.819 Post-shutdown script... 20:10:21.822 killall jackd jackd: no process found 20:10:22.230 Post-shutdown script terminated with exit status=256. 20:10:23.865 Could not connect to JACK server as client. - Overall operation failed. - Unable to connect to server. Please check the messages window for more info. Error: "/tmp/kde-asaf" is owned by uid 1000 instead of uid 0.

  Read the article

• Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

  - by D.S.

  I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

  Read the article

• Duplicity on a ReadyNAS

  - by Jason Swett

  Has anyone here run Duplicity on a ReadyNAS? I'm trying but here's what I get: duplicity full --encrypt-key="ABC123" /home/jason/ scp://[email protected]//gob Invalid SSH password Running 'sftp -oServerAliveInterval=15 -oServerAliveCountMax=2 [email protected]' failed (attempt #1) I've also found this post that says the "Invalid SSH password" message doesn't actually mean invalid SSH password. This would make sense because I'm not using an SSH password; I'm using a public key. I can ssh, ftp, sftp and rsync into my ReadyNAS just fine. (Actually, to be more accurate, I can get past authentication with ssh, ftp and sftp but I can't actually do anything past that. Regardless, that's enough to tell me that "Invalid SSH password" is bogus. Rsync works with no problems.) The post I found says the command will work as soon as the directory at the end of your scp command exists, but I don't know how to check for that. I know the share gob exists on my ReadyNAS and I know it's writable because I'm writing to it with rsync. Also, here is the verbose output: Using archive dir: /home/jason/.cache/duplicity/3bdd353b29468311ffa8485160da6873 Using backup name: 3bdd353b29468311ffa8485160da6873 Import of duplicity.backends.rsyncbackend Succeeded Import of duplicity.backends.sshbackend Succeeded Import of duplicity.backends.localbackend Succeeded Import of duplicity.backends.botobackend Succeeded Import of duplicity.backends.cloudfilesbackend Succeeded Import of duplicity.backends.giobackend Succeeded Import of duplicity.backends.hsibackend Succeeded Import of duplicity.backends.imapbackend Succeeded Import of duplicity.backends.ftpbackend Succeeded Import of duplicity.backends.webdavbackend Succeeded Import of duplicity.backends.tahoebackend Succeeded Main action: full ================================================================================ duplicity 0.6.10 (September 19, 2010) Args: /usr/bin/duplicity full --encrypt-key=ABC123 -v9 /home/jason/ scp://[email protected]//gob Linux gob 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:34:50 UTC 2010 i686 /usr/bin/python 2.6.6 (r266:84292, Sep 15 2010, 15:52:39) [GCC 4.4.5] ================================================================================ Using temporary directory /tmp/duplicity-cridGi-tempdir Registering (mkstemp) temporary file /tmp/duplicity-cridGi-tempdir/mkstemp-ztuF5P-1 Temp has 86334349312 available, backup will use approx 34078720. Running 'sftp -oServerAliveInterval=15 -oServerAliveCountMax=2 [email protected]' (attempt #1) State = sftp, Before = '[email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp -oServerAliveInterval=15 -oServerAliveCountMax=2 [email protected]' failed (attempt #1) Any ideas as to what's going wrong?

  Read the article

• litespeed issue with content-type

  - by sandeep.s85

  I am running magento with litespeed. The problem I am facing is that ajax call is being made of which header is set as x-json, but lightspeed is setting another header of text/html content type I've checked that page with apache and everything is working fine. I checked the response headers with apache and litespeed and here are they: With apache: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 05:58:47 GMT Server: Apache Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 06:58:48 GMT; path=/; domain=mydomain.com; httponly Connection: close Transfer-Encoding: chunked Content-Type: application/x-json With litespeed: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 06:10:55 GMT Server: LiteSpeed Connection: close Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 07:10:55 GMT; path=/; domain=mydomain.com; httponly Content-Type: text/html; charset=UTF-8 Content-Length: 474 Vary: User-Agent I've also added application/json to mime.properties of litespeed,restarted it but that did not work. Here is the screenshot

  Read the article

• Ubuntu root privs installation issue

  - by Pam

  I am a fairly new Ubuntu user (and Linux user, for that matter) and I just downloaded a program whose installer was a .sh file. Not thinking, I copied the installer to an /opt subdirectory, thinking that I was going to install the application there: sudo cp ~/Downloads/fooInstaller.sh /opt/someDir I can't remember, but I either had to use sudo because /opt required it, or I just used it without thinking, but in any case, I prefixed with sudo. Once in /opt/someDir, I executed the installer again, using sudo: sudo sh fooInstaller.sh The terminal went crazy, and a few seconds later, a graphical install wizard popped up that guided me through the rest of the process. At the end of the wizard I was prompted to launch the program, and I did, and everything was great. Until... I closed the program, and attempted to add it to my Ubuntu "panel" (the icon panel at the top of the screen). The program was installed to /usr/local/foo/theProgram, and so I specified that URL as the command in the custom app launcher. When I open the program through the panel/launcher (at the top of the screen), the program doesn't load or operate correctly. I get a lot of error messages complaining about being denied permissions. I'm assuming that this is a "superuser/installation/privs" issue, and not a problem with the application (hence this post at superuser.com instead of the application's forums), because when I launch the program from the terminal with sudo, it opens and executes perfectly fine, just like it did the first time around after the install wizard finished. I realize I'm probably going to have to uninstall the program completely, and re-install it differently. Finally, my question: After uninstalling, can I avoid all these issue by just running the installer (sh fooInstaller.sh) right out of my Downloads directory, sans the sudo prefix? If not, how do I get the program to install without root privs so that I can add it to my panel/launcher and get it executing correctly? Sorry for the long post but I didn't want to omit any details because, as I'm sure you can tell, I'm not really sure I know what I'm doing. Thanks for any help here!

  Read the article

• Basic Apache setup is not seeing my site

  - by Jakobud

  Sorry that is a horrible thread subject, but I cannot think of a better more descriptive subject. We are running a Fedora 11 server that is currently hosting some CRM on it. I want to use a VirtualHost directive to add another site to the server. So I created this conf: /etc/httpd/conf.d/mysite.ourdomain.com.conf And here is the content: <VirtualHost *:80> ServerName mysite.ourdomain.com DocumentRoot /www/mysite ServerAdmin [email protected] ErrorLog /var/log/mysite.ourdomain.com-error.log CustomLog /var/log/mysite.ourdomain.com-access.log common </VirtualHost> I restarted apache, getting the following warning: [warn] NameVirtualHost *:80 has no VirtualHosts From what I read, this warning is not related and I can ignore it and my site should still be up and running, correct? (I'll troubleshoot this error later if so) Well I have our DNS server setup to point mysite.ourdomain.com to goto this server. I can ping it and it points to the correct LAN IP, etc.. Now when I try to access it in the browswer I get nothing. It just says Connecting... and never gets there. If I try mysite.ourdomain.com or the IP address, neither one doesn't get there. It's a very simple and basic apache setup so I'm not sure what I'm doing wrong... Like I said, the other thing that is running on this server is a crm and it's .conf looks something like this: Listen x.x.x.x:443 <VirtualHost x.x.x.x:443> ServerAdmin [email protected] ServerName crm.ourdomain.com ErrorLog /var/log/httpd/ourdomain/crm-error.log CustomLog /var/log/httpd/ourdomain/crm-access.log common DocumentRoot /www/ourdomain/crm <IfModule mod_dir.c> DirectoryIndex /index.php </IfModule> </VirtualHost> There is also some LDAP authentication stuff in that config but I left it out cause I assumed it wasn't necessary to post. Anyone have any clue where I should start or what settings I can post from httpd.conf that would help?

  Read the article

• Problem posting multipart form data using Apache with mod_proxy to a mongrel instance

  - by Ryan E

  I am attempting to simulate my site's production environment as closely as I can on my local machine. This is a rails site that uses Apache w/ mod_proxy to forward requests to a mongrel cluster. On my Mac OSX Leopard machine, I have the default install of apache running and have configured a vhost to use mod_proxy to to forward requests to a local running mongrel instance on port 3000. <Proxy balancer://mongrel_cluster-development> BalancerMember http://127.0.0.1:3000 </Proxy> For the most part, this is working fine. I can browse my development site using the ServerName of the vhost I configured and can confirm that requests are being properly forwarded to the mongrel instance. However, there is a page on the site that has a multipart form that is used to upload an image to the server. When I post this form, there is a delay of about 5 minutes and the browser ultimately returns a Bad Request Your browser sent a request that this server could not understand. In the error log for my vhost: [Tue Sep 22 09:47:57 2009] [error] (70007)The timeout specified has expired: proxy: prefetch request body failed to 127.0.0.1:3000 (127.0.0.1) from ::1 () This same form works fine if I browse directly to the mongrel instance (http://127.0.0.1:3000). Anybody have any idea what the problem might be and how to fix it? If there is any important information that I neglected to include, post a comment, and I can add to this question. Note: Upon further investigation, this appears to be a problem specific to Safari. The form works fine in Firefox.

  Read the article

• Laptop won't boot with both memory slots used

  - by Johnny W

  I'm currently trying to upgrade my old Sony Vaio VGN-SZ1HP/B to 2GB of RAM. It already had 1GB of Crucial RAM in one of its slots, and one empty. I checked on Crucial.com and it confirms that each bank can hold 1GB of PC2-5300. The 1GB stick already installed was this, but Crucial's page recommended this... The two are identical from what I can make out, so I just ordered another one of the former. Unfortunately the machine refuses to even POST with both sticks installed. If I remove the old RAM from Slot 1 and replace it with the new RAM it runs fine. If I leave Slot 1 empty and put RAM (either stick) in Slot 2, it won't POST. Basically it seems that Slot 2 just isn't working properly. Does anyone have any ideas on how to solve this problem? Or maybe have any experience with this sort of thing with Sony Vaios? Thanks for any help!

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• Windows 8 Internet Explorer proxy automation script

  - by Stefan Bollmann

  Similar to this post, I'd like to change my proxy settings using a script. However, it fails. When I am behind the proxy, IE does not connect to the internet. Here I try the first solution from craig: function FindProxyForURL(url, host) { if (isInNet(myIpAddress(), "myactualip", "myactualsubnetip")) return "PROXY proxyasshowninpicture:portihavetouseforthisproxy_see_picture"; else return "DIRECT"; } Also this test, where isInNet should surely return true does not help: function FindProxyForURL(url, host) { if (isInNet("myactualip", "myactualip", "myactualsubnetip")) return "PROXY proxyasshowninpicture:portihavetouseforthisproxy_see_picture"; else return "DIRECT"; } **This script is saved as proxy.pac in c:\windows and my configuration is* in LAN settings: No automatically detected settings, yes, use automatic config script: file://c:/windows/proxy.pac No proxy server. *(i am not allowed to post screenshots..) So, what am I doing wrong? ---------------- update -------------- However, when I set up a proxy in my LAN configurations: IE -> Internet Options -> Connections -> LAN Settings check: Use a proxy Server for your LAN Address: <a pingable proxy> Port: <portnr> everything is fine for this environment. Now I try a simpler script like function FindProxyForURL(url, host) { return "PROXY <pingable proxy>:<portnr>; DIRECT"; } With a configuration described above** I am not able to get through the proxy.

  Read the article

• Cannot find FIS partition 'initramfs'......... need help!!!

  - by vikramtheone

  Hi Guys, I have a Ubuntu 9.04 Linux running on Freescale's i.MX515(ARM Cortex based) board with me. There were about 250 updates pending and I did that today, well some of the updates failed because of the infamous errors: E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. E: Couldn't rebuild package cache E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. So, when I do the 'sudo dpkg --configure -a' I get new errors related to FIS partition: Cannot find FIS partition 'initramfs' User postinst hook script [/usr/sbin/flash-kernel] exited with value 1 dpkg: error processing linux-image-2.6.28-18-imx51 (--configure): subprocess post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of linux-image-imx51: linux-image-imx51 depends on linux-image-2.6.28-18-imx51; however: Package linux-image-2.6.28-18-imx51 is not configured yet. dpkg: error processing linux-image-imx51 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-imx51: linux-imx51 depends on linux-image-imx51 (= 2.6.28.18.23); however: Package linux-image-imx51 is not configured yet. dpkg: error processing linux-imx51 (--configure): dependency problems - leaving unconfigured Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.28-18-imx51 Cannot find FIS partition 'initramfs' dpkg: subprocess post-installation script returned error exit status 1 Whats going wrong here, need help!!! I'm a newbie. Regards Vikram

  Read the article

• VMWare Workstation Linux Host performance tuning

  - by Hoghweed

  I need to improve my linux hosted vmware workstation for using multiple virtual machines at the same time. I feel very stupid I lost a great blog post link which I found last month (and I'm not able to find it again..) so I try to ask here if anyone can help me: This is my host (laptop): 16GB DDR3 Ram HDD Hybrid 750GB 7200 (8GB SSD Cache) Mint 15 x64 Kernel 3.9.7 swappiness set to 10 The above are the important things about the host. So, My need is the ability to run 2 or 3 VMs at the same time. The lack of performance is about the disk, The last time from that blog post I lost, I setup /tmp to be mounted ad a memory partition and in my previous installation that was good, now I'm not able to find a good solution to tweak the things. I think with 16GB o RAM there will be no problems to run multiple VMs, but whe they start to swap or use the /tmp things going bad (guest cursor going too fast after a freeze, guest freeze and so on) Anyone can help me to fit a good host tweak and configuration to get better performance? Thanks in advance

  Read the article

• Suggestions on the best home server rack cabinet

  - by allentown

  I have a lot of gear in a colocation facility right now. Some of it is going to come home with me now. I do not know anything about the "rack mount" side of the industry. I lease a rack, and I put my stuff in it. I have a few 1U boxes, a few 2U boxes, and a few 4U boxes. 1U switch. One is a new Xserve, which means it is deep. I think I can get by with around 12U to 18U. I want to keep it as small as possible, since I do not have a lot of spare space at my home. I will not be able to bolt to the wall, floor etc, so it should not be tall. This is something I would love to more or less just be a box that sits on the floor but gives me the ability to mount nicely, do nice cable management etc. Are the "post" style racks junk? I am liking the open space, and the no limitations on depth of something like this: http://www.rackmountsolutions.net/images/products/Martin-relay-rack.jpg However, that thing is way too tall, and probably way too expensive. I am looking to be around $300.00 or less. More if I have to, though I would prefer not to. These look near perfect: (See comment for this link, the system will not let me post a second url) but I am worried the Xserve will not fit in it. If anyone has any good links, or website recommendations of good past experience, I would appreciate it. I am almost considering that I may be able to build something with random scraps of stuff at Home Depot as well.

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >