Search Results

Search found 920 results on 37 pages for 'arun ac'.

Page 24/37 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• How to force laptop mode on/off

  - by Vi

  root@vi-notebook:/home/vi# laptop_mode start force Laptop mode enabled, not active How to start laptop mode? It starts successfully when AC adapter is removed, but not by explicit command. The system is GNU/Linux Debian i386 squeeze (not up to date), 2.6.30-zen2-31270-gc7099db-dirty, Acer Extensa 5220. Update: Changed to ENABLE_LAPTOP_MODE_ON_AC=1 in /etc/laptop_mode/laptop-mode.conf, now it is turned on always. But I can't turn it off with laptop_mode stop force, it stays turned on anyway. How do I turn it off again?

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Change Audio title from English to Sinhalese using ffmpeg

  - by user330461

  I insert an extra Sound track in my video file and it works well. ffmpeg -i news.mov -i news.wav -map 0:0 -map 0:1 -map 1:0 -pass 1 -vcodec libx264 -preset fast -b 512k -minrate 512k -maxrate 512k -bufsize 512k -threads 0 -f mp4 -an -y /dev/null && ffmpeg -i news.mov -i news.wav -map 0:0 -map 0:1 -map 1:0 -pass 2 -acodec libfaac -ab 128k -ac 2 -vcodec libx264 -preset fast -b 512k -minrate 512k -maxrate 512k -bufsize 512k -threads 0 -f mp4 news.mp4 The default audio track come with the label "English" and I would like to give it a label "Sinhalese" The Second Audio track come up without a label as "track#1" and I would like to give that a label of "Tamil". How do I do that ?

  Read the article

• Alienware M17x R3: Possible downclock

  - by Ywen

  I installed recently Kubuntu 11.10 32 bits (had graphics driver issues, wanted to try on 32 bits version) on my new Alienware M17x, with a Core i7-2670QM CPU. Cores are supposed to be clocked at 2.2 GHz, however the output of $ cat /proc/cpuinfo | grep -i "hz" gives me: model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 model name : Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz cpu MHz : 800.000 If useful, the AC adapter is plugged in (yet the ouput is the same when the computer is powered only by the battery) and I have Firefox and Eclipse running. Does /proc/cpuinfo reflect a possible automatic downclock made to save power if processor load is low or is this output abnormal? EDIT: Ok, I checked and yes, the ouput does vary in function of the load. I reach 2.2 GHz when needed. But my following problem remains. I was checking my CPU clocking because I experienced poor performances when reading 720p video files on Ubuntu with VLC or mplayer when on battery (and I believe VLC by default only uses CPU, not GPU to decode), whereas I haven't got such problems with VLC on Windows (which made me think it wasn't coming from a BIOS option, plus every option in the BIOS regarding the CPU is turned ON).

  Read the article

• JavaOne: Parleys.com, Spring Vs. Java EE and HTML5 tooling

  - by delabassee

  Parleys.com, a 2012 Duke's Choice Award winner, is an E-Learning platform that host content from different sources (conferences, JUGs meetings, etc.). There is a lot of technical content available for online but also offline consumption, including many sessions on Java EE. Parleys has just released, for free, all the Devoxx 2011 sessions (video and slides sync'ed!). From a technical point of view, Parleys.com is interesting as they have switched from Spring to Java EE 6 to avoid being locked in a proprietary framework. During the GlassFish Community BoF, Stephan Janssen (Parleys.com and Devoxx founder) also presented how GlassFish is used to support 2000 concurrent Parleys users over a cluster of 2 GlassFish instances. Talking about Java EE and/or Spring, Harshad Oak has posted an update on the 'Spring Vs. Java EE' panel discussion that took place on Tuesday. As Arun said standards such as Java EE does not necessarily refrain innovation: "JBoss Forge & Arquillian from RedHat are great examples of innovation in the JavaEE community. Standardization is important but innovation does continue even within that framework." Simplicity, productivity along with HTML5 are the driving themes of Java EE 7. In terms of simplicity and productivity, the developer experience can also be improved by the tooling. Every NetBeans release comes with a large set of improvements, the just released NetBeans 7.3 beta is no exception. The goal of ‘NB 7.3’s Project Easel’ is to improve HTML5 development, something that will be handy for Java EE 7 developers. Project Easel can, for example, communicate directly to Chrome's WebKit engine, this feature was shown during Sunday's Technical Keynote at the end of the Java EE section. In this beta release, Chrome and the embedded JavaFX browser are the only supported browsers but the NetBeans team plan to add support, over time, for other WebKit based browsers. NetBans 7.3 beta NetBeans 7.3 screenscasts Today (i.e. Wednesday 3rd) is also the final exhibition day, so make sure to visit the Java EE and the GlassFish pods on the Java DEMOgrounds (Hilton Grand Ballroom, 9:30 am - 5:00 pm). Finally, here are some Java EE and GlassFish related activities worth attending today if you are at JavaOne : Wednesday October 3rd Time Title Location 8:30-9:30am What's New in Servlet 3.1: An Overview Parc 55 Mission 8:30-9:30am Bean Validation 1.1: What's New Under the Hood Parc 55Cyril Magnin II/III 10:00-11:00am JSR 353: Java API for JSON Processing Parc 55 Mission 10:00-12:00pm Tutorial : Integrating Your Service into the GlassFish PaaS Platform Parc 55 Devisidero 11:30-12:30pm What's New in JSF: A Complete Tour of JSF 2.2 Parc 55Cyril Magnin I 11:30-12:30pm Best of Both Worlds: Java Persistence with NoSQL and SQL Parc 55 Mission 1:00-2:00pm Sharding Middleware to Achieve Elasticity and High Availability in the Cloud Parc 55Market Street 1:00-2:00pm Pimp My RESTful Java Applications Parc 55Cyril Magnin I 3:00-4:00pm Migrating Spring to Java EE Parc 55Cyril Magnin II/III 4:30-5:30pm JavaEE.Next(): Java EE 7, 8, and Beyond Parc 55Cyril Magnin II/III 4:30-5:30pm HTML5 WebSocket and Java Parc 55Cyril Magnin I 4:30-5:30pm Easy Middleware for Your Embedded Device Nikko Ballroom II/III

  Read the article

• Geek Bike Ride JavaOne 2012

  - by Tori Wieldt

  "Geek Bike Ride?" the clerk at the bike rental shop asked. "Are you guys all from the same company?" "We aren't even from the same country!" we answered. "I'm from Russia." "We're from Germany."  "I'm from Belgium." "I'm from Palo Alto." "I'm from Japan."  "We're from Brazil." "We're from Brazil." "I'm from Sweden." "Coooool" was all she could say. She was right. The Geek Bike Ride was cooool. We had 39 bike riders and one skater show up Saturday for a great route from San Francisco's Fisherman's Wharf, across the Golden Gate bridge, to Saulsalito, and back to the city by ferry. Duke Bike jerseys, sponsored by OTN, were given out. To make sure Java developers got them, each person had to answer a Java question to get a jersey. The questions were really hard, like "Who is the Father of Java?" "What's the biggest Java conference in San Francisco?" The best was when the question was "Name one of Duke's Choice Award winner from this year," and Régina ten Bruggencate answered answered "Me!"  It was foggy throughout the day, with the sun poking out occasionally. The fog was thickest on the bridge, more that one rider commented that we were "in the cloud." It was a great day to meet new friends, and have a chat with old friends. We all had fun, though some of us may more a little more slowly during JavaOne. Ride on!  Photos by permission by Arun Gupta and Yoshio Terada. Thanks, guys!

  Read the article

• SVN: Error validating server certificate for svn hook linux

  - by Dr Casper Black

  Hi, I managed to setup a SVN (over SSL) server and TortoiseSVN client on Win. I made a Post-Commit Hook for test project. The Post-Commit will update the web dir so the App in PHP can be executed with the newest version. It all works when done over shell. The only problem is, when i commit the changes over the client in Win the change is commited but HOOK throws error post-commit hook failed (exit code 1) with output: Error validating server certificate for 'https://SERVER_IP:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! - The certificate hostname does not match. Certificate information: - Hostname: DEVSRVR - Valid: from Fri, 28 Jan 2011 09:22:45 GMT until Sat, 28 Jan 2012 09:22:45 GMT - Issuer: PHP, SS, SS, SRB - Fingerprint: 5f:d0:50:d6:dd:a6:d4:64:a5:ac:3a:4b:7c:7d:33:e3:75:dd:23:9f (R)eject, accept (t)emporarily or accept (p)ermanently? svn: OPTIONS of 'https://SERVER_IP/svn/myproject/trunk': Server certificate verification failed: certificate issued for a different hostname, issuer is not trusted (https://SERVER_IP)

  Read the article

• upgrading my computer system for office use

  - by denise ellul

  Presently I have the under-mentioned computer system. What should be changed and upgraded with the following products that I own presently? I am interested in performance issues related to cache memory, bus speed, RAM, CAS latency as well as other considerations. Thanks for your help. Processor (CPU): Intel Celeron Dual Core E3300 2.5 GHz Motherboard: Asus P5QPL-AM G41 Main Memory (RAM): 2 GB Team Elite DDR2 PC8000 Case: Coolermaster RC330 Power Supply Unit: 500W EZ-Cool Standard Storage Device (Hard Drive): 500GB Samsung Video Card: Intel GMA X4500 (On-board) Optical Drive: LG GH22NS50 Sound Card: AC 97 (On – board) Card Reader: Akasa Black TFT Monitor: 19” View Sonic Speakers: Logitech S120 2.0

  Read the article

• Dark screen when wake / Unable to control screen brightness

  - by John

  Running Ubuntu 11.04 on Lenovo ThinkPad with an Nvida graphics card. The unit goes to sleep when the lid is shut. (The unit goes to suspend mode (not to disk/hibernate), AC gets turned off, running on battery) Upon lid-open sometimes the screen is almost too dark to read. I'm really not sure of the exact cause, (very low batt??). The only fix is a reboot. The screen brightness buttons have never worked in Ubuntu. I have messed w/ the power management preferences. No change. At one point I messed w/ the gnome settings. No change. I have tried a few cmds: echo 9>/sys/class/backlight/acpi_video0/brightness setpci -s 00:02.0 F4.B=10 xgamma -gamma .75 None of these help. Most have zero effect. I think it is and acpi thing, but that is just a guess. I'm out of idea's, and looking for suggestions. Thanks

  Read the article

• How do I disable all lid close processes?

  - by Mat

  I want to be able to close my laptop without Ubuntu registering it. I've been looking everywhere and I've found plenty of people with the same problem but no real solutions. Obviously I have set the lid close setting to 'do nothing' for both AC and battery, but when I close the lid it still blanks the screen, disconnects from external monitors, and brings up the lock screen when I reopen it. Some people have suggested disabling the lock screen, but this doesn't stop the screen blanking and external displays disconnecting, and I don't want to disable the lock anyway, as I still want it when I tell Ubuntu to lock or sleep or whatever else. Others have suggested it's something to do with ACPI support, but I have tried changing some ACPI scripts, and even removed them completely (e.g. /etc/acpi/lid.sh and /etc/acpi/events/lidbtn) and it makes no difference. There must be a bit of code somewhere that can just be removed or commented out or altered to prevent any lid close actions - does anyone know where? I know this has been asked before, but I'm getting really frustrated with this problem. I'm disappointed to say that I'm actually using Windows 7 more often just because it's quite happy to completely ignore the closed lid. So I just wanted to check, are we any closer to a real solution for this problem?

  Read the article

• Compute the AES-encryption key given the plaintext and its ciphertext?

  - by Null Pointers etc.

  I'm tasked with creating database tables in Oracle which contain encrypted strings (i.e., the columns are RAW). The strings are encrypted by the application (using AES, 128-bit key) and stored in Oracle, then later retrieved from Oracle and decrypted (i.e., Oracle itself never sees the unencrypted strings). I've come across this one column that will be one of two strings. I'm worried that someone will notice and presumably figure out what those two values to figure out the AES key. For example, if someone sees that the column is either Ciphertext #1 or #2: Ciphertext #1: BF,4F,8B,FE, 60,D8,33,56, 1B,F2,35,72, 49,20,DE,C6. Ciphertext #2: BC,E8,54,BD, F4,B3,36,3B, DD,70,76,45, 29,28,50,07. and knows the corresponding Plaintexts: Plaintext #1 ("Detroit"): 44,00,65,00, 74,00,72,00, 6F,00,69,00, 74,00,00,00. Plaintext #2 ("Chicago"): 43,00,68,00, 69,00,63,00, 61,00,67,00, 6F,00,00,00. can he deduce that the encryption key is "Buffalo"? 42,00,75,00, 66,00,66,00, 61,00,6C,00, 6F,00,00,00. I'm thinking that there should be only one 128-bit key that could convert Plaintext #1 to Ciphertext #1. Does this mean I should go to a 192-bit or 256-bit key instead, or find some other solution? (As an aside, here are two other ciphertexts for the same plaintexts but with a different key.) Ciphertext #1 A ("Detroit"): E4,28,29,E3, 6E,C2,64,FA, A1,F4,F4,96, FC,18,4A,C5. Ciphertext #2 A ("Chicago"): EA,87,30,F0, AC,44,5D,ED, FD,EB,A8,79, 83,59,53,B7.

  Read the article

• Acer Aspire One 725 - missing graphic card driver for Radeon HD 7290?

  - by Melon

  Recently I bought an Acer Aspire One 725 Netbook and installed Ubuntu 12.10 on it. I bought it, because it can run HD movies and has Full HD on external VGA port. However, movies from youtube have a really slow framerate. If you open three tabs in Opera (for example g-mail, youtube and askubuntu) it gets really laggy. My suspicion is that the driver for graphic card is missing. When I check the System->Details->Graphics the driver is unknown. After running lspci | grep VGA I get this output: 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Device 980a From what I see, I have a AMD C70 processor integrated with AMD Radeon HD 7290. Has anyone had the same problem? Do you know which drivers need to be installed for the graphics to work properly? On official Acer page there are only drivers for Win7 and Win8... Update: OK. Another attempt. I have a fresh Ubuntu 12.10. All updates done. downloaded Catalyst 12.11 beta drivers and decided to create a package. After installing package, I have this error from /var/log/Xorg.0.log: [ 13.394] (**) fglrx(0): NoAccel = NO [ 13.394] (**) fglrx(0): AMD 2D Acceleration Architecture enabled [ 13.394] (--) fglrx(0): Chipset: "AMD Radeon HD 7290 Graphics" (Chipset = 0x980a) [ 13.394] (--) fglrx(0): (PciSubVendor = 0x1025, PciSubDevice = 0x0740) [ 13.394] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD [ 13.394] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000 [ 13.394] (--) fglrx(0): MMIO registers at 0xf0200000 [ 13.394] (--) fglrx(0): I/O port at 0x00003000 [ 13.394] (==) fglrx(0): ROM-BIOS at 0x000c0000 [ 13.484] (II) fglrx(0): ATIF platform detected [ 13.564] (II) fglrx(0): AC Adapter is used [ 13.565] (EE) fglrx(0): V_BIOS address 0xd00 out of range [ 13.565] (EE) fglrx(0): Failed to obtain VBIOS from Kernel! [ 13.565] (EE) fglrx(0): VBIOS read from Kernel, Invalid signature! [ 13.565] (EE) fglrx(0): GetBIOSParameter failed [ 13.565] (EE) fglrx(0): PreInitAdapter failed [ 13.565] (EE) fglrx(0): PreInit failed [ 13.565] (II) fglrx(0): === [xdl_xs113_atiddxPreInit] === end

  Read the article

• rel="nofollow" SEO impact

  - by Torez

  I saw a technique used where there was a block with three parts: 1. Image (wrapped in an anchor tag) 2. Heading (anchor tag with heading text) 3. Paragraph (regular p tag with synopsis content) e.g. <li class="block"> <a rel="nofollow" class="thumb" href="#"><img src="images/placeholder_service_thumbnail.jpg" alt="" /></a> <a class="h3" href="#"Good SEO Heading</a> <pPellentesque habitant morbi tristique senectus et netus et malesuada fames ac turpis egestas. Vestibulum tortor quam, feugiat vitae, ultricies eget, tempor sit amet, ante. Donec eu...</p> </li> With the image tag there was a rel="nofollow" on the wrapped anchor tag. So the idea is that the users still has the ability to click the image and go to the details page, but the image link does not rank. When users click on the heading text, that is only what ranks for that specific page. Q: Is this the correct approach? Does this even do anything? What is the best practice?

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Regarding the battery of a new laptop [closed]

  - by Majed

  Possible Duplicate: Is it better to use a laptop on battery or on AC power? I bought a new laptop from HP. I am not sure if I should remove the battery while I am working on my laptop or not. What is better for my laptop battery, to keep it while the laptop is plugged in or to remove it? or to charge it and then pull out the plug and when the battery is flat then plug it again? I use my laptop alot (at home and sometimes at work as well).

  Read the article

• Oracle At QCon SF 2012

  - by Cassandra Clark - OTN

  Oracle Technology Network is a Platinum sponsor at QCon San Francisco.  (qconsf.com).  Don’t miss these great developer focused sessions: Shay ShmeltzerHow we simplified Web, Mobile and Cloud development for our own developers? - the Oracle StoryOver the past several years, Oracle has beendeveloping a new set of enterprise applications in what is probably one of thelargest Java based development project in the world. How do you take 3000 developers and make them productive? How do you insure the delivery of cutting edge UIs for both Mobile and Web channels? How do you enable Cloud baseddevelopment and deployment?  Come and learn how we did it at Oracle, and see how the same technologies and methodologies can apply to your development efforts. Dan SmithProject Lambda in Java 8Java SE 8 will include major enhancements to the Java Programming Language and its core libraries.  This suite of new features, known as Project Lambda in the OpenJDK community, includes lambda expressions, default methods, and parallel collections (and much more!).  The result will be a next-generation Java programming experience with more flexibility and better abstractions.   This talk will introduce the new Java features and offer a behind-the-scenes view of how they evolved and why they work the way that they do. Arun GuptaJSR 356: Building HTML5 WebSocket Applications in JavaThe family of HTML5 technologies has pushed the pendulum away from rich client technologies and toward ever-more-capable Web clients running on today’s browsers. In particular, WebSocket brings new opportunities for efficient peer-to-peer communication, providing the basis for a new generation of interactive and “live” Web applications. This session examines the efforts under way to support WebSocket in the Java programming model, from its base-level integration in the Java Servlet and Java EE containers to a new, easy-to-use API and toolset that are destined to become part of the standard Java platform. The full conference schedule is here: http://qconsf.com/sf2012/schedule/wednesday.jsp But wait, there’s more!  At the Oracle booth, we’ll also be covering: ·         Oracle ADF Mobile·         Oracle Developer Cloud Service·         Oracle ADF Essentials·         NetBeans Project Easel Lastly we’ll share the results of a short cloud survey at QConSF ater this week.  If you attended this year's Oracle OpenWorld and JavaOne conferences, it would be hard not to notice that Oracle is clearly "all-in" when it comes to the Cloud.  With Cloud computing being such a hot topic on many OTN members' minds, we'd like to know what you're doing in the cloud and invite you to take this short cloud survey.

  Read the article

• merging video and audio with custom panning

  - by cherouvim

  I have: a video which has mono audio inside a audio (mono) I'd like to merge those two to a single video file containing: video from #1 audio from #1 full left pan + audio #2 full right pan Is this possible in ffmpeg using 1 command? I've tried the following which almost does this but the video/audio gets out of sync: ffmpeg -i video.mp4 -filter_complex "amovie=audio.wav [r] ; [r] amerge" output.mp4 -y I've managed to do it with multiple commands: #1 create right panned audio ffmpeg -i audio.wav -ac 2 -vbr 5 audio-stereo.mp3 -y ffmpeg -i audio-stereo.mp3 -af pan=stereo:c1=c1 audio-right.mp3 -y #2 create left panned video ffmpeg -i video.mp4 -af pan=stereo:c0=c0 video-left.mp4 -y #3 merge the two ffmpeg -i video-left.mp4 -i audio-right.mp3 -filter_complex "amix=inputs=2" video-mixed.mp4 -y It does the job, but is it possible with 1 command?

  Read the article

• verisign certificate into jboss server SSL

  - by rfders

  i'm trying to enable jboss to uses ssl protocol using a previously generated certificate from verisign, i imported both certificate, server certificate and ca certificate into the keytore file, and i configured the server.xml to use that keystore and activate ssl protocol, then when i run the jboss, I got this error "certificate or key corresponds to the SSL cipher suites which are enabled" Question, reading some post on internet, i found that every example was made it generating a Certificate Request, it stricly necesary to do that if i already have the server certificate and that CSR has to be imported into the keystore as well ? at this point i'm very confused about this issue, i tried almost every solutions posted in several forums but till now i haven't any luck !! can you give me some tips in order to solve this problem. thanks in advance this are my keystore file: Keystore type: jks Keystore provider: SUN Your keystore contains 2 entries j2ee, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): 69:CC:2D:2A:2D:EF:C4:DB:A2:26:35:57:06:29:7D:4C ugent, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): AC:D8:0E:A2:7B:B7:2C:E7:00:DC:22:72:4A:5F:1E:92 and my server.xml configuration:

  Read the article

• Regarding temperature in our server cabinet

  - by kafka

  We have a floor standing server cabinet, which sits in the corner of our office. There is no AC in the office, and the average temperature is around 21C (70F). The server cabinet currently contains 2 tower servers, a switch and a router. It's well enough ventilated, but does get understandably warm in there. We've recently put a thermometer in there to monitor the temperature, and recently I've noticed the temperature hit 33C (91F). What I'd like to know is if this temperature is too high, and whether there is a maximum temperature we should not be exceeding?

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Do you work in your server room?

  - by Gary Richardson

  I once had a job offer from a company that wanted my workstation to be in the AC controlled, noisy server room with no natural light. I'm not sure what their motivation was. Possibly it made sense to them for me to be close to the servers, or possibly they wanted to save the desk space for other employees. I turned down the job (for many reasons, including the working environment). Is this a common practice? Do you work in your LAN room? How do you cope?

  Read the article

• ASUS EeePC 1001PX, hard disk clicking in Ubuntu Maverick

  - by MeanEYE

  I just received my new Asus EeePC 1001px netbook. After installing Ubuntu 10.10 on it, I've noticed that my hard drive is making a clicking noise. Now this is not a loud clicking noise nor it's constant (only sounds occasionally and when hard disk is not writing or reading anything). Another strange thing is, this only happens when netbook is using battery power, the moment I plug in AC power clicking stops. Additionally I noticed that when I go into BIOS I can hear the click only once, same thing happens if I boot Ubuntu from USB. That led me to believe the problem is within operating system. I did all the surface scans and SMART tests and everything seems to be fine. Now noise sounds like heads are trying to "park" themselves so I tried disabling "spin down" option in Power Management but it didn't help. Any idea?

  Read the article

• Putting servers inside a refrigerator? [closed]

  - by Muhammad Jamal Shaikh

  It could be a silly question, but I decided to go for it. I shall be buying 3 servers in the next few weeks to set up a small webfarm at my home. I am told by different people who work in server rooms, that I should keep my servers in an air conditioned room. Which is really expensive, because the temperature here in south asia is between 10 to 50 degrees C. Here comes the funny part: I have an extra fridge in my home, why shouldn't I put the servers inside that fridge? Benefits: I don't have to buy the air conditioner. I don't have to buy the rack mount for the servers. The electricity consumed by the fridge is much much less than AC. Give me your suggestions!

  Read the article

• putting servers inside a fridge! [closed]

  - by Muhammad Jamal Shaikh

  hi , i think its a silly question , but i decided to go for it. i shall be buying 3 servers in next few weeks for setup a small webfarm at my home. i am told by different people who work in server rooms , that i should keep my servers in a Air Conditioned room. which is really expensive.because temperature in south asia is b/w 10--50(Centigrade). here comes the funny part, i have an extra fridge in my home , why shouldn't i put the servers inside that fridge. here are benefits listed i dont have 2 buy the air Conditioner i dont have to buy the rack mount for the servers the electricity consumed by the fridge in much much lessor as compared to an AC be free to give your suggestions :) thanks Jamal.

  Read the article

• Why is music tagging software so inconsistent?

  - by Billy ONeal

  Hello :) A few years ago I spent an insane amount of time using the excellent Tag&Rename program. However, I find that for random, inexplicable reasons, some music tools simply disregard my tags, and drop or destroy the album art, or have strange handling around some characters. For example, "AC/DC" is poorly handled by most music players when I use Tag&Rename to write the tags. Is there a piece of software that works like Tag&Rename but is more compatible, or is there a way to ensure Tag&Rename writes more compatible tags?

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >