Search Results

Search found 1596 results on 64 pages for 'belongs on serverfault'.

Page 24/64 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

  • Utilize two gateways on the same network same interface with load balancing

    - by RushPL
    My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

    Read the article

  • What are the cheap CDN for Origin Pull?

    - by DucDigital
    I've read several thread around ServerFault about this, but still I am not satisfy with the answer so I post a question here. I need a Origin Pull CDN that support big file (more than 200MB). I don't need a storage place since they are too small, just to relay the server. Also the price should be afforable, ofcourse not more than 150$ a month for their smallest plan. I also need to pay by credit card since I do not work or stays in the US so it's hard for me to do a bank wire. Thank you very much

    Read the article

  • Debugging an IP Camera

    - by Kevin Boyd
    Further to my previous question on ServerFault here, I finally can view the stream on RTSP however I still cannot view the camera stream in a web browser. The IP camera uses an activeX control in Internet Explorer. And although I can configure the camera settings from IE, I cannot view the stream it shows connecting for a few sec and shows disconnecting. I have forwarded the HTTP, RTSP and Stream ports of the IP camera. the public port is 7071 and private port is 7070. When I try to see the connections in TCPView it shows that the ActiveX control in IE is trying to connect to port 7070 which is quite unusual since it should connect to 7071 Also the state shows SYN_SENT for sometime and then disconnects. I have really no clue what's going on and why?

    Read the article

  • HOWTO Catch/Redirect all outgoing e-mails from webapp on Windows Server 2003

    - by John
    As suggested by another member, I have split the original post into two. To see the original post, go to http://serverfault.com/questions/134595/howto-catch-redirect-all-outgoing-e-mails-on-win2k-and-redhat-enterprise. For this question, please keep your answers specific to Windows Server 2003 only. Thanks for the help in advance. Background: I am integrating two separate web application that are developed in ASP .NET and JSP/Struts. As such, they are hosted on two different server technologies, namely Win2K3 and Redhat Enterprise Server 5.5. Problem: There is a copy of production data in my test environment with real e-mail addresses. I need to test the e-mail functionality of these applications, but I do not want them to send out actual e-mails. Is there a way to catch and redirect all outgoing e-mails? Ideally, I would like to send all outgoing e-mails to another e-mail (i.e., [email protected]) so my testers can look at them.

    Read the article

  • How to set IP address of Amazon EC2 instance to its Elastic IP?

    - by TWord
    Hi, I have an Amazon EC2 instance running and I am installing a program on it that needs to know what the machine's IP address is. Can I set the Elastic IP address to the IP address within the EC2 instance? Its okay if it reroutes data packets somewhere 'outside' and then back to itself, but the software NEEDs me to specify an IP address of the machine its on. I proceeded with the software installation using the "local IP" (10.xx.xx.xx) within the software installation. I don't know if this is the reason why the application is not visible publicly (as I'm trying to determine in the question http://serverfault.com/questions/166946/allowing-web-access-to-an-amazon-ec2-windows-server-2008-instance-running-tomcat)

    Read the article

  • How can I send a Wake on Wireless LAN (WoWLAN) / Wake on Demand request manually?

    - by pioto
    This is similar to, but not the same as, http://serverfault.com/questions/1721/is-wireless-wake-on-lan-possible. I know it is supposed to be possible. The question is, how do I do whatever the AirPort Basestation will do? All I can find so far is that supposedly I need to send something with Wireless Multimedia Extensions (WMM): Basically, I want to be able to wake up my Mac Mini remotely, probably using my Linux laptop. Does anyone know of a tool to do this? Basic Wake on LAN tools do not seem to be the right thing. I don't need the Sleep Proxy Service bit, because I already know the MAC address of the system I want to wake up.

    Read the article

  • mailman not relaying email to external address

    - by gozzilli
    I have a setup of mailman with postfix on an ubuntu server 12.04. My problem is that mailing list emails are not forwarded to email addresses external to my institution. However the initial welcome email is received by everyone, internally and externally. in fact, a simple email from command line with mail is successfully sent to anyone after that, mailing list emails are only forwarded to internal addresses. the domain name I'm using for the server is not that of my institution who is hosting the server. Here is my main.cf: myorigin = sub.myinstitution.tld mynetworks = 127.0.0.0/8 xxx.xxx.xxx.xxx/16 # this is my institution ip range relayhost = smtp.myinstitution.tld inet_interfaces = loopback-only local_transport = error:local delivery is disabled virtual_alias_maps = hash:/etc/postfix/virtual smtpd_recipient_restrictions = permit_mynetworks myhostname = mywebsite.tld mydestination = $myhostname, localhost.$mydomain, localhost I also found these two links on serverfault and ubuntu forums, but neither of these solutions seem to do the trick for me. Any help would be much appreciated.

    Read the article

  • how to workaround glassfish 3.0.1 admin page slow startup?

    - by black sensei
    I've installed netbeans which comes with glassfish. i just got a book about glassfish and i wanted to try.the first surprise is the time it took to the admin page to load. i've found on serverfault and by googling that the server is making call to external resource on the network on online (not sure about that). but the adding of the java options didn't speed up the loading of the admin page. how to work around it? i've heard so good about glassfish that this leaves me perplexed. thanks for reading and for helping.

    Read the article

  • Howto boot directly into a VirtualBox image?

    - by mawimawi
    I have a running setup as following: Native OS: Windows 7 64bit, 3 Partitions: c: (System) d: (FAT32, here is my vdi file) e: (unformatted) VirtualBox: Fedora 14 running off the vdi file on drive d. Usually this setup is great for me, but sometimes I'd like to run Linux natively, and not inside VirtualBox. Is there a way to boot directly into the vdi file without the Windows overhead? E.g. using a USB stick with some modified Linux Kernel / GRUB that can mount the vdi file directly as "/"? Or copy the contents of my vdi file to the empty partition and somehow use this from VirtualBox (when booting into Windows) AND directly booting into Linux? Hope to get some hints or even howtos. EDIT: yes, sorry. not programming related. I posted the question to serverfault.com (hopefully that's the better site for my question.)

    Read the article

  • Fastest web server for serving static content

    - by Swader
    Hello, I'm optimizing our system for some faster static content delivery, and was wondering if anyone has any proper experience with the fastest web servers out there for such a purpose. From the three main candidates I've considered, Nginx, Cherokee and Lighttpd, each seems to have its own problems - but the reports I've read online are somewhat biased and lean towards whichever server the user is currently using. Any ideas on where to see a proper benchmark for this specific purpose, or at least a non-biased list of pros and cons? Any personal experiences and pitfalls I should be vary of? Thanks Edit: Serverfault.com gave the answer as nginx. I'd still like to hear some developer thoughts from this end of the universe.

    Read the article

  • How to let users change linux password from web browser?

    - by wag2639
    I'm not sure if this is a stackoverflow question or serverfault but here goes: I have an Ubuntu 10.04 file server (Samba/FTP/HTTP) and I would like to have the ability to give users the ability to change their password to the server using their web browser. I've written a similar script before using PHP and a mess of exec but I believe that isn't secure because it can be listened to by someone looking at the list of processes on the server. Is there some kind of plugin (PHP or Python or other) that can do this easily? I rather not use something like webmin as it's overkill for this.

    Read the article

  • VirtualBox Port Fowarding to Connect to PostgreSQL Database

    - by kliao
    I'm trying to connect to a PostgreSQL database hosted on a Win7 guest from a Win7 host. I've configured security in pg_hba.conf host all all 127.0.0.1/32 md5 host all all 10.0.2.15/32 md5 host all all 192.168.1.6/32 md5 and set the listen_addresses setting in postgresql.conf to '*'. I think I've set up port forwarding correctly as I see: Key: VBoxInternal/Devices/e1000/0/LUN#0/Config/win7_vm1/GuestPort, Value: 5432 Key: VBoxInternal/Devices/e1000/0/LUN#0/Config/win7_vm1/HostPort, Value: 5432 Key: VBoxInternal/Devices/e1000/0/LUN#0/Config/win7_vm1/Protocol, Value: TCP when I call getextradata. This is similar to http://serverfault.com/questions/106168/cant-connect-to-postgresql-on-virtualbox-guest but I'm not sure what I'm doing wrong. In the vbox.log file I see: 00:00:01.019 NAT: set redirect TCP host port 5432 = guest port 5432 @ 10.0.2.15 00:00:01.033 NAT: failed to redirect TCP 5432 = 5432 but I'm not sure how to fix that. Any ideas? Thanks.

    Read the article

  • VMWare Workstation Dev Machine Disks: one fast or four echofriendly raid?

    - by Avi
    I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines - A dev machine running VS-2010, a build machine, a version-control machine, a web server for testing, a "personal" machine running office etc. I'll be connecting the computer to my stereo, so I'll also be running iTunes (possible on a dedicated VM) and I want the computer to be a silent one. I'll probably use an Antec P183 case. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. So, my question is as follows: In terms of heat, noise, reliability, warranty, price, capacity and performance, what would you suggest: A Raid10 4 disk array using eco-friendly disks such as the $94 1TB Western Digital Caviar Green, or one high performance disk such as the 2TB Western Digital Caviar Black at $280?

    Read the article

  • Possible to use DRBD on two ESXi virtualized servers?

    - by chen
    I have two servers (attached disks have been set up as hardware RAID1 for disk device level failure resilience). Here is the setup in my mind: 1) Install ESXi on each of the physical server, M1, M2; 2) Start one VM on each of the ESXi virtualized physical server V1, V2; 3) Install the DRDB drivers within V1 and V2. Essentially, this is a "virtualizing machine running DRBD in the VM's instead of bare metal hardware" idea. My question is whether the above setup can achieve the same "networked RAID1" goal that DRDB can achieve in the bare-metal physical machines (http://www.drbd.org/). Thanks. [EDIT] I found this (http://serverfault.com/questions/49305/drbd-experimentation-and-virtualization) is a similar question, but the answer does not seem to be firmative enough for me to follow.

    Read the article

  • Domino 8.5.3: Attaching an Object Residing on Server (Lotusscript preferred)

    - by Void
    Not sure if this question is more appropriate for ServerFault or StackOverflow, sorry if it should belong elsewhere! I am working on an application and one of the function is to automatically send an email with an attachment. I can code the application to attach the object when it resides on local or on a mapped drive. Newbie Question: Is there a way to have the object reside on the Domino server, and still be able to point to it and have the application automatically attach and send? Is there any method that allows me to do this? Users have no direct access to the server/filesystem, so mapped drive of the Domino server is out of the question. Hope someone can shed some light on this question. Thanks!

    Read the article

  • icacls, Network Service, and setting ACLs on Windows Server 2008

    - by Ted
    Setting ACLs on Windows Server 2008 via the command line is giving me some problems. As per http://web2.minasi.com/forum/topic.asp?TOPIC%5FID=26907 I've tried all sorts of variations: C:\Windows\system32icacls "D:\Websites\site.com\Web\bin*" /grant 'NT A uthority\NETWORK SERVICE: (OI) (CI)M' C:\Windows\system32icacls "D:\Websites\site.com\Web\bin*" /grant "NETWORK SERVICE": (OI) (CI)M And all variations in between. However, each try leads to i.e. "Invalid parameter "'NETWORK'"" depending on the variation above. As per http://technet.microsoft.com/en-us/library/cc753525%28WS.10%29.aspx (see in comments), it appears that others have experienced the same issue where the same command works on Windows 7/Vista/etc., but not on Windows Server 2008. What's the best way to apply permissions to Network Service account on a directory and/or files via the command line in Windows Server 2008? Especially as there's no way to do multiple file permissions at once via the GUI (see http://serverfault.com/questions/30991/windows-server-2008-change-security-settings-for-multiple-files-at-once).

    Read the article

  • Very high memory usage, but not claimed by any process?

    - by SharkWipf
    While stress-testing LVM on one of our Debian servers, I came across this issue where memory would fill up a lot to the point where it would run the server out of memory, but no process would claim the memory. See http://i.imgur.com/cLn5ZHS.png, and see http://serverfault.com/a/449102/125894 for an explanation on the colors used in htop. Why is this happening? And is there any way to see what process is using the memory? Htop is configured not to hide any processes, so what is it that htop is missing? In this particular case, I can fairly certainly say that it is caused, directly or indirectly, by lvmcreate, lvmremove or dmsetup, as I was stress-testing that. Do note that this question is not about solving the LVM problem, but about why the memory isn't claimed by any process. Stopping all LVM commands does bring the memory back down to <600MB.

    Read the article

  • Why do some software not get load balanced even when there are multiple cores?

    - by Nav
    While VTune Analyzer was running on a blade server with 8 cores, I observed the cpu useage percentage using mpstat -P ALL 1. mpstat showed me that VTune was taking up 100% of a single core, while all other cores were idle. Why does that happen? Shouldn't the OS (RHEL Server 5.2) automatically distribute load across cores? The same happened when I tried running MATLAB (even after enabling multithreading support in the MATLAB settings). p.s: I'm a developer. Not a sys admin. So felt it better to ask here rather than at serverfault.

    Read the article

  • What kind of hosting do I need?

    - by Robert Smith
    I migrated this question from serverfault. Hopefully this is the appropriate place. I have been trying to answer this question but I haven't found an specific answer to my situation. As I want to pay for what I need, I thought I could get a good answer here. I have a custom made forum (rather than a built-in forum like the ones you can find in plugins, e.g. WP-Forum or phpBB type of software) in Django. I don't want to use Apache and modwsgi because it's usually very memory-hungry and I can't afford a big server. I prefer a combination of nginx and gunicorn which I think is very efficient (maybe you can also tell me what you think about that). I'm expecting to receive 10,000 to 20,000 visits each month with 15,000 to 30,000 page impressions. I have reviewed some cloud services like Amazon EC2 or Rackspace and other more traditional services (Linodo). This site won't use videos or big images and I certainly don't need a huge amount of bandwidth (200GB would be definitely too much). I need shell access so shared hosting is out of the question. What do I need to run a website like that without problems? What about RAM? 256MB would be enough (that's the amount of RAM offered by small instances in Amazon and Rackspace)? Do you know of any alternative to those I mentioned? If you need more information to provide a useful answer, please don't hesitate to ask. By the way, I was told that Linodo is not all that different to Amazon EC2 but this website is supposed to work 24/7, so I can't take advantage of Linodo's flexibility regarding creating and deleting instances. Thanks in advance.

    Read the article

  • Route multiple subdomains on one external ip to multiple internal ips

    - by Abenil
    i have several subdomains(git.example.org, build.example.org, etc.), i have a router with an external ip and i have several virtual machines on a host computer with internal ips. Now i want to route git.example.org to internal ip 10.0.2.1 and build.example.org to internal ip 10.0.2.2. How can I do this? I setup in the Router that all traffic on port 80 is comming to my host computer with internal ip 10.0.2.3 and installed Squid on that computer. I added the following lines to the squid.conf file: cache_peer 10.0.2.1 parent 80 0 no-query originserver name=server_1 cache_peer_domain server_1 git.example.org cache_peer 10.0.2.2 parent 80 0 no-query originserver name=server_2 cache_peer_domain server_2 build.example.org But this is not working for me. :( Any help appreciated. Regards Nils Update: Here is the solution for Apache http://serverfault.com/a/273693

    Read the article

  • Only ONE Outlook 2010 installation "Cannot connect to Exchange server" when setting up new profile.

    - by Johnny PDEX
    Exchange 2010, one-server installation (small production, I know not best practice) OWA Connectivity has been confirmed, Autodiscover is configured and working properly for EVERY other installation. Other user accounts tested on problem Outlook, none can connect. Windows Firewall is pre-configured by Group Policy, only modifications being related to remote management. Firewall has also been disabled during diagnostic period. Network discovery and file sharing is enabled on workstation as well. Windows 7 Professional, latest updates installed. Driving me nuts. Help, serverfault?

    Read the article

  • Is Page-Loading Time Relevant?

    - by doug
    Take this (ServerFault) page for instance. It has about 20 elements. When the last of these has loaded, the page is deemed "loaded"--but not before. This is certainly the protocol used by our testing service (which is among the small group of well-known vendors that offer that sort of service). Obviously this method is based on a clear, definite endpoint--therefore it's easy to apply w/ concomitant reliability. I think it's also the metric used by the popular Firefox plugin, 'YSlow.' For my employer's website, nearly always the last-to-load items are tracking code, tracking pixels, etc., so from the user's point of view--their perception--the page was "loaded" well before it had actually loaded based on the criterion used by our testing service (15-20% is a rough estimate). I'm sure i'm not the first person to consider this nor the first to wonder if it is causing micro-optimization while ignoring overall system-level, or user-perceived performance. So my question is, are there are other more practical (yet still reasonably precise) measures of page loading time?

    Read the article

  • X58 RAID 10 - Am I forced to use Sata2?

    - by Avi
    I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. I contacted my supplier who suggested a gigabyte X58A motherboard and 4 Western Digital Caviar black 6Gb/s disks. I have checked the spec for the X58A board, however, and it says: SATA 3Gb/s: RAID 0, RAID 1, RAID 5, and RAID 10 SATA 6Gb/s: RAID 0, and RAID 1. I'm losing half the bandwidth because I'm forced to use SATA2! What should I do?

    Read the article

  • Recurring network issues the same time every day.

    - by Peter Turner
    Something has been happening on my company's network at 9:30 every day. I'm not the sysadmin but he's not a ServerFault guy so I'm not privy to every aspect of the network but I can ask questions if follow up is needed. The symptoms are the following : Sluggish network and download speed (I don't notice it, but others do) 3Com phones start ringing without having people on the other end. We've got the following ports exposed to the public for a web server, a few other ports for communicating with our clients for tech support and a VPN. We've got a Cisco ASA blocking everything else. We've got a smallish network (less than 50 computers/vms on at any time). An Active Directory server and a few VM servers. We host our own mail server too. I'm thinking the problem is internal, but what's a good way to figure out where it's coming from?

    Read the article

  • Is it possible to avoid umask 0002?

    - by Anatoly
    Is it possible to give an automatic ability to modify files(folders and all recursively) created by one user to another within one specified folder (let's say "shared") on the basis of both users belonging to the same secondary group (let's say "coworkers")? I've tried to achieve this by using ACL but with no success. Seems that umask wipes out corresponding bits.... I'm on FreeBSD 8.1 (but seems this problem is actual for other *NIX systems). Googling this problem (people often refer to it as "umask per directory" problem) gives the most relevant link: http://old.nabble.com/ACLs,-umask-and-shared-directories-td27820947.html that is not very promising... Want to ask ServerFault community - is it possible at all?

    Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >