Search Results

Search found 7606 results on 305 pages for 'raam dev'.

Page 249/305 | < Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >

• PPTP Client setup, Fedora 17

  - by Suarez Romina

  I am trying to connect to hidemyass.com VPN services via PPTP, but I am having issues understanding why it isn't working, since I don't get a warning or fatal error and my IP remains the same. This is how i create the connection: [root@lasvegas-nv-datacenter ~]# pptpsetup --create TUNNELNAME --server 199.58.165.20 --username MYUSERNAME --password MYPASSWORD --encrypt --start And this is the output: Using interface ppp0 Connect: ppp0 <-- /dev/pts/1 CHAP authentication succeeded MPPE 128-bit stateless compression enabled local IP address 10.200.21.14 remote IP address 10.200.20.1 After that, I check the log and this is what i get: [root@lasvegas-nv-datacenter ~]# tail -f /var/log/messages Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 1 'Start-Control-Connection-Request' Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:754]: Received Start Control Connection Reply Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:788]: Client connection established. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 7 'Outgoing-Call-Request' Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:873]: Received Outgoing Call Reply. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:912]: Outgoing call established (call ID 0, peer's call ID 20096). Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: CHAP authentication succeeded Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: MPPE 128-bit stateless compression enabled Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: local IP address 10.200.21.14 Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: remote IP address 10.200.20.1 Can someone help me? Basically, i Ieed to connect to the VPN and have my IP changed after the connection. I read a lot of guides but still cannot understand why I don't get a connection.

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast (Corvallis, OR) to the east coast (NY, NY). However, I am seeing some disturbing latency numbers from my location (Berkeley, CA) to the NYC host. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: Berkeley to NYC server: 215 ms latency, 46ms transfer time, 261ms total Berkeley to Corvallis server: 114ms latency, 41ms transfer time, 155ms total some URLs if you want to try yourself: http://careers.stackoverflow.com/content/cso/img/logo.png (NY, NY) http://serverfault.com/cache/logo.png (Corvallis, OR) It makes sense that Corvallis, OR is geographically closer to Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only went up 10%, yet the latency went up ten times as much! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... http://serverfault.com/questions/63531/does-routing-distance-affect-performance-significantly http://serverfault.com/questions/61719/how-does-geography-affect-network-latency http://serverfault.com/questions/6210/latency-in-internet-connections-from-europe-to-usa ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• Apache & SVN on Ubuntu - Post-commit hook fails silently, pre-commit hook “Permission Denied”

  - by 113169587962668775787

  I've been struggling for the past couple days to get post-commit email notifications working on my SVN server (running via HTTP with Apache2 on Ubuntu 9.10). SVN commits work fine, but for some reason the hooks are not being properly executed. Here are the configuration settings: - Users access the repo via HTTP with the apache dav_svn module (I created users/passwords via htpasswd in a dav_svn.passwd file). dav_svn.conf: <Location /svn/repos> DAV svn SVNPath /home/svn/repos AuthType Basic AuthName "Subversion Repository" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user </Location> I created a post-commit hook file that writes a simple message to a file in the repository root: /home/svn/repos/hooks/post-commit: #!/bin/sh REPOS="$1" REV="$2" /bin/echo 'worked' > ${REPOS}/postcommit.log I set the entire repository to be owned by www-data (the apache user), and assigned 755 permissions to the post-commit script when I test the post-commit script using the www-data user in an empty environment, it works: sudo -u www-data env - /home/svn/repos/hooks/post-commit /home/svn/repos 7 But when I commit on a client machine, the commit is successful, but the post-commit script does not seem to be executed. I also tried running a simple script for the pre-commit hook, and I get an error, even with an empty pre-commit script: "Commit failed (details follow): Can't create null stdout for hook '/home/svn/repos/hooks/pre-commit': Permission denied" I did a few searches on Google for this error and I presume that this is an issue with the apache user (www-data) not having adequate permissions, specifically to execute /dev/null. I also read that the reason post-commit fails silently is because that it doesn't report with stdout. Anyway, I've also tried giving the apache user (www-data) ownership of the entire repository, and edited the apache virtualhost to allow operations on the server root, and I'm still getting permission denied /etc/apache2/sites-available/primarydomain.conf <Directory /> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> Any ideas/suggestions would be greatly appreciated! Thanks

  Read the article

• Cachefilesd (cachefiles) everything seems to be set up, still not working

  - by Evgenius

  I'm trying to set up cachefilesd to work with my network folder shared using NFS. I have seemingly everything set up, however cachefilesd starts normally, however caching isn't functioning. Here is output of commands, which I ran in the same order 1 sudo mount ... cache-1:/mnt/datashared on /mnt/nfsshare type nfs (rw,sync,ac,acregmin=3,acregmax=60,acdirmin=30,acdirmax=300,lookupcache=pos,vers=3,fsc) ... 2 lsbmod | grep cachefiles cachefiles 40555 1 fscache 57430 4 nfs,cifs,cachefiles,nfsv4 3 [edited - deleted] 4 uname -r 3.8.0-34-generic 5 grep CONFIG_NFS_FSCACHE /boot/config-3.8.0-34-generic CONFIG_NFS_FSCACHE=y 6 lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 13.04 Release: 13.04 Codename: raring 7 sudo service cachefilesd restart * Restarting FilesCache daemon cachefilesd [ OK ] 8 dmesg [6211206.141781] FS-Cache: Withdrawing cache "mycache" [6211210.135236] FS-Cache: Cache "mycache" added (type cachefiles) [6211210.135242] CacheFiles: File cache on sdb1 registered [6214644.348929] CacheFiles: File cache on sdb1 unregistering [6214644.348935] FS-Cache: Withdrawing cache "mycache" [6214654.575909] FS-Cache: Cache "mycache" added (type cachefiles) [6214654.575915] CacheFiles: File cache on sdb1 registered 9 ps aux | grep cachefilesd root 65399 0.0 0.0 4460 540 ? Ss 23:14 0:00 /sbin/cachefilesd 1000 65464 0.0 0.0 8160 916 pts/0 S+ 23:16 0:00 grep --color=auto cachefilesd finally, biggest problem is 10 cat /proc/fs/nfsfs/volumes NV SERVER PORT DEV FSID FSC v3 64476645 801 0:24 233e020f0da07a93 no tl;dr I think I configured everything properly but FSC mount option + fscachefilesd don't seem to work

  Read the article

• How can I close a port that appears to be orphaned by Xvfb?

  - by Jim Fiorato

  I'm running Xvfb on a FC8 Amazon EC2 image. On occasion Xvfb will crash (unable at the moment to find out the reason for the crash), and after crashing the TCP port will appear to be orphaned. I'm unable to get a PID to kill any process that may be using it. I'm starting Xvfb with: Xvfb :7 -screen 0 1024x768x24 & Examples of what I'm working with are below, the Xvfb port is (was) 6007: # netstat -ap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:ssh *:* LISTEN 1894/sshd tcp 0 0 *:6007 *:* LISTEN - tcp 0 352 ip-10-84-69-165.ec2.int:ssh c-71-194-253-238.hsd1:51689 ESTABLISHED 2981/0 udp 0 0 *:bootpc *:* 1817/dhclient udp 0 0 *:bootpc *:* 1463/dhclient Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ] DGRAM 871 668/udevd @/org/kernel/udev/udevd unix 2 [ ACC ] STREAM LISTENING 5385 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 6 [ ] DGRAM 5353 1867/rsyslogd /dev/log unix 2 [ ] DGRAM 11861 2981/0 unix 2 [ ] DGRAM 5461 1974/crond unix 2 [ ] DGRAM 5451 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5438 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 5437 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5396 1880/dbus-daemon unix 3 [ ] STREAM CONNECTED 5395 1880/dbus-daemon unix 2 [ ] DGRAM 5361 1871/rklogd # lsof -i COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME dhclient 1463 root 3u IPv4 4704 UDP *:bootpc dhclient 1817 root 4u IPv4 5173 UDP *:bootpc sshd 1894 root 3u IPv4 5414 TCP *:ssh (LISTEN) sshd 2981 root 3u IPv4 11825 TCP ip-10-84-69-165.ec2.internal:ssh->c-71-194-253-238.hsd1.il.comcast.net:51689 (ESTABLISHED) Attempting to force the port closed with iptables doesn't seem to work either. iptables -A INPUT -p tcp --dport 6007 -j DROP I'm at a loss as to how to reclaim/free the port. From what I can tell, this port will remain in this state until the EC2 instance is shut down. So, how can I close this port so I can restart Xvfb?

  Read the article

• Remote NX login to Ubuntu, Gnome can't mount CD/DVD drive

  - by T.J. Crowder

  Even though I'm sitting next to it, I log into my Ubuntu 10.04 LTS system via NX Free Edition from another system at the moment (this is temporary, not worth buying a KVM for). Curiously, though, when I do that Gnome's auto-mounting fails for CD/DVD media (I haven't tried other kinds) with a "Not Authorized" error. For instance here's what happens when I put the Ubuntu 10.04 LTS installation CD in: This does not happen if I log into it locally (not via NX) with the same user account. When using NX, I can mount the media if I go to mount directly: tjc@midnight:~$ sudo mkdir /media/dvd tjc@midnight:~$ sudo mount -r -t iso9660 /dev/sr0 /media/dvd tjc@midnight:~$ ls /media/dvd autorun.inf casper dists install isolinux md5sum.txt pics pool preseed README.diskdefines ubuntu wubi.exe ...which, along with the "not authorized" error, suggests some kind of permissions problem to me (doh). What I find odd is that the same user is involved in both cases (local and via NX). I'm new to Ubuntu on the desktop (used it and other distros on servers for years), so I'm afraid I don't know how this auto-mounting is happening. I think it's handled by the gvfs package and its daemon, but that's about as far as I got (and perhaps I've taken a left turn even getting that far). Although I can work around it with mount, does anyone know how I might get auto-mounting to work?

  Read the article

• Making OpenSSL work on PHP Windows 2008 server with FastCGI

  - by KacieHouser

  I have been researching all day. Here is what I have done: In C:/PHP/php.ini and C:/PHP/php-cgi-fcgi.ini I have made the extension_dir = "C:/PHP/ext" I uncommented extension=php_openssl.dll I went to http://windows.php.net/download/ and got the thread safe version with the PHP 5.4 (5.4.8) version of DLL's In C:/PHP/ext I replaced the php_openssl.dll with the one I downloaded In System32 and SysWOW64 I added the following DLL's ssleay.dll libeay.dll I restarted the IIS server in the Server Manager under Web Server and stopped and started the World Wide Web Publishing Service That didn't work, so I tried same thing with the unthreaded versions. I still get: Fatal error: Call to undefined function ftp_ssl_connect() in C:\inetpub\wwwroot\REMOVED_dev\save_data.php on line 5 Here are related things from phpinfo(): System Windows NT DEV-WEB1 6.1 build 7601 (Windows Server 2008 R2 Standard Edition Service Pack 1) i586 Compiler MSVC9 (Visual C++ 2008) Architecture x86 Configure Command cscript /nologo configure.js "--enable-snapshot-build" "--enable-debug-pack" "--disable-zts" "--disable-isapi" "--disable-nsapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=C:\php-sdk\oracle\instantclient11\sdk,shared" "--with-enchant=shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze" "--with-pgo" Server API CGI/FastCGI Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\PHP\php-cgi-fcgi.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) Registered PHP Streams php, file, glob, data, http, ftp, zip, compress.zlib, compress.bzip2, https, ftps, sqlsrv, phar Registered Stream Socket Transports tcp, udp, ssl, sslv3, sslv2, tls FTP support enabled Protocols dict, file, ftp, ftps, gopher, http, https, imap, imaps, ldap, pop3, pop3s, rtsp, scp, sftp, smtp, smtps, telnet, tftp openssl OpenSSL support enabled OpenSSL Library Version OpenSSL 0.9.8t 18 Jan 2012 OpenSSL Header Version OpenSSL 0.9.8x 10 May 2012 What am I missing here?

  Read the article

• Kate gives out debug messages on the console from which it is started

  - by Elan

  I am new to Linux. I use Ubuntu 11.04. Whenever I open a file with kate from the commandline, with 'kate &' (or without ampersand), Kate starts out giving messages on the console. It continuously gives them out as I save a file or close one. They look like debug messages to me (sample below). I have used Synaptic package manager to install Kate. Uninstalling and installing the dev version did not make any change. Soon my console becomes cluttered. Is there a way to suppress these messages? There was nothing explicit in Kate settings either. Thank you, The messages look like kate(13412)/kate-filetree KateFileTreeModel::handleInsert: BEGIN! kate(13412)/kate-filetree KateFileTreeModel::handleInsert: creating a new root kate(13412)/kate-filetree ProxyItem::ProxyItem: ProxyItem(0x1796840,0x0,-1,QObject(0x0) .... kate(13435)/kate-filetree KateFileTreeModel::documentActivated: adding viewHistory ProxyItem(0x1eb7cf0,0x1eb6830,0,KateDocument(0x1d93ea0) , "Untitled" ) kate(13435)/kate-filetree KateFileTreeModel::updateBackgrounds: BEGIN! kate(13435)/kate-filetree KateFileTreeModel::updateBackgrounds: END! kate(13435)/kate-filetree KateFileTreeModel::documentActivated: END! kate(13435)/kate-filetree KateFileTreePluginView::viewChanged: END! X Error: BadWindow (invalid Window parameter) 3 Major opcode: 20 (X_GetProperty) Resource id: 0x5601b42 X Error: BadWindow (invalid Window parameter) 3 Major opcode: 20 (X_GetProperty) Resource id: 0x5601b42

  Read the article

• Vserver: secure mails from a hacked webservice

  - by lukas

  I plan to rent and setup a vServer with Debian xor CentOS. I know from my host, that the vServers are virtualized with linux-vserver. Assume there is a lighthttpd and some mail transfer agent running and we have to assure that if the lighthttpd will be hacked, the stored e-mails are not readable easily. For me, this sounds impossible but may I missed something or at least you guys can validate the impossibility... :) I think basically there are three obvious approaches. The first is to encrypt all the data. Nevertheless, the server would have to store the key somewhere so an attacker (w|c)ould figure that out. Secondly one could isolate the critical services like lighthttpd. Since I am not allowed to do 'mknod' or remount /dev in a linux-vserver, it is not possible to setup a nested vServer with lxc or similar techniques. The last approach would be to do a chroot but I am not sure if it would provide enough security. Further I have not tried yet, if I am able to do a chroot in a linux-vserver...? Thanks in advance!

  Read the article

• Windows Server 2008 R2 SP1 Drivers Missing Would Not Install?

  - by bleepzter

  I am building my dev machine with WS2008R2SP1. I consider Windows Server as the best development environment for C# since I tend to focus on server-centric (integration) applications. The desktop flavor of Windows (7) doesn't play nicely with things like Commerce Server or BizTalk... so I to like stick to the environment I develop for. Previously I used to develop inside of VM's but I've found that it is super inefficient and tends to take a toll on the laptops. (I've gone through two of them in 6 months). Problem is that I multiple devices that do not want to be recognized by Windows: My machine is Dell Precision M4500: Intel Core i7-Q740, 1TB HDD, 8GB RAM, Dell re-branded Broadcom DW1501 802x11n Half-Mini Card, Dell re-branded Broadcom DW375 Bluetooh Module, Intel 82577LM Gigabit Network connection NVidia Quadro FX1800 Graphics The devices in question are the Dell rebranded broadcom network and bluetooth adapters: Broadcom USH: USB\VID_0A5C&PID_5800&REV_0101&MI_00 USB\VID_0A5C&PID_5800&MI_00 DW375 Bluetooth Module USB\VID_413C&PID_8187&REV_0517 USB\VID_413C&PID_8187 When I ran the broadcom installers I get "Operating System not supported" which I think is a big oversight on Broadcom's part. Why check for system version string? UGHGHGH Moreover if I try to manually force the driver in windows... I get an error: Driver Management concluded the process to install driver FileRepository\btwampsecfl.inf_amd64_neutral_d8fc2b85d035ed47\btwampsecfl.inf for Device Instance ID USB\VID_0A5C&PID_5800&MI_00\7&66DE6C9&0&0000 with the following status: 0xe0000217. '- or - Driver Management concluded the process to install driver FileRepository\btwampfl.inf_amd64_neutral_d4c4acf036c61299\btwampfl.inf for Device Instance ID USB\VID_413C&PID_8187\90004EEEF5A6 with the following status: 0xe0000217. I googled the 0xe0000217 error code and it says Bad service install section in the driver inf file... Any ideas on how to fix this? I also tried the post by BetaIQ on MSDN Forum, unfortunately the links to the driver package included in the post were dead :( PS. On a side note I also do mobile development for Android, iOS, and Windows Phone, and BB. Having the bluetooth is quite useful with mobile devices.

  Read the article

• How do I easily repair a single unreadable block on a Linux disk?

  - by Nelson

  My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

  Read the article

• Can't boot flash drive on GIGABYTE motherboard

  - by Deltik

  Situation When I try to boot from my flash drive, my GIGABYTE 970A-UD3 motherboard returns this: Loading Operating System ... Boot error All other motherboards I've tried support booting from that flash drive (and a backup flash drive). The operating systems I tried on both flash drives were created with usb-creator-gtk (Ubuntu USB Startup Disk Creator). I know that the motherboard understands that there is an operating system on the flash drives because when I erase them, it complains in an ALL CAPS RAGE that there isn't an operating system, which is correct. How can I boot a flash drive that's bootable from other motherboards on this motherboard? Qualification This question is not a duplicate of this one because directly writing to the flash drive as an ISO 9660 (dd if=operating_system.iso of=/dev/sdb) still does not have the motherboard recognize the operating system. This question should be a duplicate of this one because I provide more information not provided by that poster. This forum thread has broken links and does not have a solution to my problem. Nobody knows what's going on in this forum thread.

  Read the article

• Sparc v440 unable 2 boot after recommended patch install

  - by user100660

  After installing the October 2011 recommended patch bundle on a Solaris 10 the host fails to boot. The output is {0} ok boot SC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Sun Fire V440, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.10.10, 8192 MB memory installed, Serial #54744555. Ethernet address 0:3:ba:43:55:eb, Host ID: 834355eb. Rebooting with command: boot Boot device: /pci@1f,700000/scsi@2/disk@0,0:a File and args: \ Evaluating: Out of memory Warning: Fcode sequence resulted in a net stack depth change of 1 Evaluating: Evaluating: The file just loaded does not appear to be executable. {3} ok If I do a boot -F failsafe the host come up and I'm able to mount the root device (ufs on /dev/dsk/c1t0d0s0) and nothing appears broken, i.e I can see the logfiles from the patch install etc. Root device still have 1GB+ free. Only 2 kernel patches was installed from the patch bundle: 144500-19 & 147440-02. Any hints how to debug it further, etc.

  Read the article

• Google Chrome mouse wheel takes keyboard focus

  - by Steve Crane

  I recently switched the default browser on all my machines from Firefox to Google Chrome. In general I’m loving Chrome but there is one behaviour that is driving me nuts. Scrolling with the mouse wheel takes keyboard focus away from the document. Here’s what happens. I’ve just opened a page or switched to a new tab and the page has keyboard focus as I can use the keyboard up/down and PgUp/PgDn keys to scroll it; no problem there. But if I then use the wheel on my mouse to scroll the page, it loses the keyboard focus and no longer responds to up/down, PgUp/PgDn, or in fact any other keyboard keys. I have to click on the page background to restore the keyboard focus. This is a minor inconvenience for scrolling but where it really drives me nuts is in Google Reader and Gmail where I use keyboard shortcuts a lot. Here I find that I scroll the article or e-mail I’m reading with the mouse wheel then get no response when I press j/k to move to the next or previous article or e-mail. I am using Windows 7 and the Chrome dev channel (version 4.0.249.43).

  Read the article

• Solaris TCP stack tuning

  - by disserman

  We have a large web project (about 2-3k requests per second), using haproxy (http://haproxy.1wt.eu/) as a frontend and load balancer between the java application servers. The frontend (haproxy) is running on Linux but we are going to migrate it to the Solaris 10 as all our other servers are running under Solaris. After switching a traffic I see the two things: a) the web site became loading slower (5-10 seconds with images in comparison to 2-3 seconds on Linux) b) sometimes haproxy fails to perform a "lifecheck" (get a special web page and analyze http response code) due to the socket timeout. After switching traffic back to Linux everything is okay. I've tried to tune all params I found in /dev/tcp but no progress. I believe the problem is in some open socket limitations. If someone can point me to the answer, I would be greatly appreciated. p.s. haproxy is running under Xen DomU on Linux (Kernel 2.6.18, Debian 5), under zone on Solaris (10 u8). the only thing we did on Linux is increasing of ip_conntrack_max (I believe Solaris option tcp_conn_req_max_q is the equivalent).

  Read the article

• What causes this logrotate behavior in Puppet?

  - by ujjain

  After running logrotate, Puppet starts writing it's logs into /var/log/puppet/masterhttp.log-20130616. How come it doesn't keep logging in /var/log/puppet/masterhttp.log? It seems normal behavior is renaming the original log-file and start with a clean fresh log-file to start writing in that log file, keeping the other file as a log-archive. [root@puppetmaster puppet]# ls -al total 97520 drwxr-x---. 2 puppet puppet 4096 Jun 16 03:24 . drwxr-xr-x. 12 root root 4096 Jul 1 09:11 .. -rw-r--r--. 1 puppet puppet 0 Jun 16 03:24 masterhttp.log -rw-rw----. 1 puppet puppet 99847187 Jul 1 09:19 masterhttp.log-20130616 [root@puppetmaster init.d]# cat /etc/logrotate.d/puppet /var/log/puppet/*log { missingok notifempty create 0644 puppet puppet sharedscripts postrotate pkill -USR2 -u puppet -f /usr/sbin/puppetmasterd || true [ -e /etc/init.d/puppet ] && /etc/init.d/puppet reload > /dev/null 2>&1 || true endscript } [root@puppetmaster init.d]# How can I make Puppet log to /var/log/puppet/masterhttp.log and not to /var/log/puppet/masterhttp.log-20130616? Even restarting puppet doesn't make it log into /var/log/puppet/masterhttp.log instead of /var/log/puppet/masterhttp.log-20130616.

  Read the article

• How to add a Linux Partition on FreeBSD

  - by Ömer

  Today I installed FreeBSD 9.0 PPC on my Mac mini G4 with 40GB HDD. During installation, (using the FSBD utility 'gpart') I have allocated a total of about 23GB for FreeBSD leaving 17GB totally free (neither partitioned, nor formatted) for a later Linux installation. Now, when try to install Linux (Ubuntu 10.10 PPC) on the remaining 17GB, the Linux/Ubuntu installer (or Linux's Disk Utility for the same matter) wants presumably a linux partition and when I try to add a (Linux) partition on that area using Linux DU it fails with this message: Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/hda, start=23363101696, size=16644660224, type= Entering MS-DOS parser (offset=0, size=40007761920) No MSDOS_MAGIC found Exiting MS-DOS parser Entering Apple parser Mac MAGIC found, block_size=512 map_count = 17 Leaving Apple parser Apple partition table detected containing partition table scheme = 2 got it Error: The partition's data region doesn't occupy the entire partition. ped_disk_new() failed Now, I'm trying to add a Linux partition on FreeBSD running on the harddisk. I use seemingly most suitable tool for this job: gpart. Here is the 'gpart show ad0' But it seems unable to add a Linux partition because "man gpart" doesn't list either "Linux Partition" nor anything like Ext2 or Ext3/Ext4. The closest thing to Linux Partition in gpart is "mbr" but it doesn't work: #gpart add -t mbr ado So, how to add properly a Linux Partition on FreeBSD? Thanks.

  Read the article

• Trying to run QEMU with a file as hda

  - by Felix

  I'm trying to run QEMU and use a simple file on the host system as the guest's hard drive. Here's what I attempted so far: $ dd if=/dev/zero of=/home/felix/vm/archlinux.img bs=1MB count=8192 8192+0 records in 8192+0 records out 8192000000 bytes (8.2 GB) copied, 86.6054 s, 94.6 MB/s $ qemu -hda /home/felix/vm/archlinux.img -cdrom archlinux-2009.08-netinstall-i686.iso -boot d Then I try to install Archlinux to that file. It goes pretty well (it's able to format it from what I can tell) until I start installing packages, when I get errors like this: And, of course, everything goes downhill from there (unable to mount the partition, corrupted files, ...). What am I doing wrong? Note: I'm just doing this for entertainment purposes. I don't intend to actually use this on servers or anything. The only use I can think of for this kind of installation would be to actually get an 8GB USB stick and dd that file to it and wham! You have a bootable stick with a fully fledged and customized OS, and without torturing the stick through the installation.

  Read the article

• Flash Media Server won't run on RHEL 6.2 EC2 instance - _defaultRoot__edge1 experienced 1 failure

  - by edoloughlin

  I've got a fresh Redhat Enterprise 6.2 64-bit instance on EC2. I've turned off the firewall and have installed an FMS 4.5 dev server. The FMS install failed, complaining about a missing libcap.so until I installed the libcap.i686 package. The following libcap packages are now installed: libcap.i686 2.16-5.5.el6 @rhui-us-east-1-rhel-server-releases libcap.x86_64 2.16-5.5.el6 @koji-override-0/$releasever libcap-ng.x86_64 0.6.4-3.el6_0.1 @koji-override-0/$releasever libpcap.x86_64 14:1.0.0-6.20091201git117cb5.el6 In the logs directory I have admin and master logs (only). The admin logs look ok: #Fields: date time x-pid x-status x-ctx x-comment 2012-02-29 09:24:26 1144 (i)2581173 FMS detected IPv6 protocol stack! - 2012-02-29 09:24:26 1144 (i)2581173 FMS config <NetworkingIPv6 enable=false> - 2012-02-29 09:24:26 1144 (i)2581173 FMS running in IPv4 protocol stack mode! - 2012-02-29 09:24:26 1144 (i)2581173 Host: ip-10-204-143-55 IPv4: 10.204.143.55 - 2012-02-29 09:24:26 1144 (i)2571011 Server starting... - 2012-02-29 09:24:26 1144 (i)2631174 Listener started ( FCSAdminIpcProtocol ) : localhost:11110/v4 - 2012-02-29 09:24:27 1144 (i)2631174 Listener started ( FCSAdminAdaptor ) : 1111/v4 - 2012-02-29 09:24:28 1144 (i)2571111 Server started (./conf/Server.xml). - I can't connect an RTMP client to the FMS. The master logs contain these lines, repeating every 5 seconds: 2012-02-29 10:43:17 1076 (i)2581226 Edge (2790) is no longer active. - 2012-02-29 10:43:17 1076 (w)2581255 Edge (2790) _defaultRoot__edge1 experienced 1 failure[s]! - 2012-02-29 10:43:17 1076 (i)2581224 Edge (2793) started, arguments : -edgeports ":1935,80" -coreports "localhost:19350" -conf "/opt/adobe/fms/conf/Server.xml" -adaptor "_defaultRoot_" -name "_defaultRoot__edge1" -edgename "edge1". -

  Read the article

• Arch linux - strange behaviour after installing fglrx

  - by kosto

  I have a problem with drivers on arch linux. I installed catalyst through unnoficial catalyst repo as wiki says. pacman -S catalyst catalyst-utils aticonfig --initial After this operation i rebooted the system. KDM loaded succesfully, but when i tried to switch to console (ctrl+alt+1/2/3) i saw only some strange dots, like pixels from the text were splitted on the whole screen. I was able to go back to kdm and enter the account details tho. This gave me a hang just before kde loaded. Here's a video where i'm showing above actions. Anybody knows what caused the problem? I can still chroot to fix some issues. Thanks for interest. http://glothriel.org/arch/arch_problem.ogg same thing on gnome / gdm, that's my second try on installing catalyst on arch. Open drivers suck the battery 2x faster. ___________EDIT_____________ Ok, i found a sollution, so i'm posting if someone else shares my problem. Catalyst does not support KMS, so you need to disable it from grub. You must know where are your /etc and /boot paritions mounted. If you have only one partition for / it's even simplier. Mount / on /mnt mount /dev/sdaX /mnt where X is number of the partition where is your / installed arch-chroot /mnt nano /etc/default/grub and add line: GRUB_CMDLINE_LINUX="nomodeset" save and quit then run (this will delete your windows grub configuration) grub-mkconfig -o /boot/grub/grub.cfg exit umount /mnt reboot

  Read the article

• How to find cause of main file system going to read only mode

  - by user606521

  Ubuntu 12.04 File system goes to readonly mode frequently. First of all I have read this question file system is going into read only mode frequently already. But I have to know if it's not caused by something else than dying hard drive. This is server provided by my client and I am just runing there some node.js workers + one node.js server and I am using mongodb. From time to time (every 20-50h) system suddenly makes filesystem read only, mongodb process fails (due read-only fs) and my node workers/server (which are started by forever) are just killed. Here is the log from dmesg - I can see there some errors and messages that FS is going to read-only, and there is also some JOURNAL error but I would like to find cause of those errors.. http://speedy.sh/Ux2VV/dmesg.log.txt edit smartctl -t long /dev/sda smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.5.0-23-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net SMART support is: Unavailable - device lacks SMART capability. A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. What I am doing wrong? Same is for sda2. Morover now when I type any command that not exists in shell I get this: Sorry, command-not-found has crashed! Please file a bug report at: https://bugs.launchpad.net/command-not-found/+filebug Please include the following information with the report:

  Read the article

• Why is my RapidSSL Certificate chain is not trusted on ubuntu?

  - by olouv

  I have a website that works perfectly with Chrome & other browser but i get some errors with PHP in CLI mode so i'm investigating it, running this: openssl s_client -showcerts -verify 32 -connect dev.carlipa-online.com:443 Quite suprisingly my HTTPS appears untrusted with a Verify return code: 27 (certificate not trusted) Here is the raw output : verify depth is 32 CONNECTED(00000003) depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=20:unable to get local issuer certificate verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=27:certificate not trusted verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 So GeoTrust Global CA appears to be not trusted on the system (Ubuntu 11.10). Added Equifax_Secure_CA to try to solve this... But i get in this case Verify return code: 19 (self signed certificate in certificate chain) ! Raw output : verify depth is 32 CONNECTED(00000003) depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify error:num=19:self signed certificate in certificate chain verify return:1 depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 Edit Looks like my server does not trust/provide the Equifax Root CA, however i do correctly have the file in /usr/share/ca-certificates/mozilla/Equifax...

  Read the article

• Postfix: change sender in queued messages

  - by ring0

  Following a complete re-installation we got a problem with the configuration: the sender address was wrong and some recipients (mail servers) rejected them. So there is a bunch of mails stuck in the Postfix queue. Ideally, a change of the sender address directly in the queued mails, and then flushing the queue would be optimal. I tried this answer that addresses this very problem. But messages don't seem to be easily modifiable in the version I have (2.11.0). For instance there is no /var/spool/mqueue dir, but, instead, /var/spool/postfix/... active bounce corrupt defer deferred dev etc flush hold incoming lib maildrop pid private public saved trace usr and the dir of interest is deferred. I tried to modify a few files there changing the wrong domain with the correct one (and was careful to ensure only those were changed). But then, those mails were moved to corrupt, meaning that a simple text change doesn't seem to work (done with vi). Any other cleaner way to change the sender in queued mails?

  Read the article

• SQL Server Express backup/restore error: The Media Family on Device is Incorrectly Formed.

  - by Chris

  Basically, I'm having this issue: http://www.sqlcoffee.com/Troubleshooting047.htm What I'm doing is running a script I found online (http://pastebin.com/3n0ZfybL) to do a full backup, then rar'ing up the file and moving it to my computer. The CRC of the backup file inside the rar is correct on both computers, so there is no problem with data being corrupted when I transfer it. But then I go and try to restore the database on my dev computer here and I get the errors "sql server cannot process this media family" ... "msg 3013". Why is this happening? I'd test out the backup on the server I'm getting it from, but it's a production server. Edit: I was about to say how I wasn't doing anything stupid like trying to restore the database to an earlier version of SQL Server, but apparently I am: From: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) To: Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Feb 9 2007 22:47:07 Copyright (c) 1988-2005 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6001: Service Pack 1) Let me get back to this post after I reinstall this.

  Read the article

< Previous Page | 245 246 247 248 249 250 251 252 253 254 255 256  | Next Page >