Search Results

Search found 3710 results on 149 pages for 'protocol analyzer'.

Page 25/149 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• Exchange 2003 mail non-delivery (NDR), spam activity? events 7002 & 7004

  - by HighTechGeek

  Windows Server 2003 Small Business Server SP2 Exchange Version 6.5 (Build 7638.2: Service Pack 2) This network has been neglected and has been having email problems for years and was on many blacklists. I was called in after the server eventually crashed... I got the server back up and running, but email problems persist. Outgoing mail delivery is sporadic. Sometimes the mail goes through, sometimes a delayed delivery report is generated after a day or more, and sometimes it seems to go through, but the recipient never receives it. Not sure if spammers are successfully using the server as a relay (see event entries below after turning on maximum SMTP logging)... User PCs infected with viruses and server was blacklisted on many sites (I used mxtoolbox.com) I have cleaned all the PCs and changed all passwords (including administrator) I have requested removal from all of the blacklists - most have removed the listing, some take more time. I have setup rDNS pointer records with the ISP (Comcast) - that was one reason for some of the blacklistings. I have tested that it's not an open relay using telnet as described here: www.amset.info/exchange/smtp-openrelay.asp I followed the advise of a Spamhaus & Microsoft article to enable maximum SMTP logging. http://www.spamhaus.org/faq/answers.lasso?section=isp%20spam%20issues#320 which directed me to Microsoft KB article 895853, specifically, the part 2/3 down titled: "If mail relay occurs from an account on an Exchange computer that is not configured as an open relay" . The Application Event Log is filling with this type of activity (Event ID 7002, 7002 & 3018 errors): Event Type: Error Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7004 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol error log for virtual server ID 1, connection #621. The remote host "212.52.84.180", responded to the SMTP command "rcpt" with "550 #5.1.0 Address rejected [email protected] ". The full command sent was "RCPT TO: ". This will probably cause the connection to fail. and this: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #620. The remote host "212.52.84.170", responded to the SMTP command "rcpt" with "452 Too many recipients received this hour ". The full command sent was "RCPT TO: ". This may cause the connection to fail. or a variant of: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 8:39:21 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #661. The remote host "82.57.200.133", responded to the SMTP command "rcpt" with "421 Service not available - too busy ". The full command sent was "RCPT TO: ". This may cause the connection to fail. also Event Type: Error Event Source: MSExchangeTransport Event Category: NDR Event ID: 3018 Date: 1/18/2011 Time: 9:49:37 AM User: N/A Computer: SERVER Description: A non-delivery report with a status code of 5.4.0 was generated for recipient rfc822;[email protected] (Message-ID ). Causes: This message indicates a DNS problem or an IP address configuration problem Solution: Check the DNS using nslookup or dnsq. Verify the IP address is in IPv4 literal format. Data: 0000: ef 02 04 c0 ï..À Any guidance and/or suggestions and/or tests to perform would be greatly appreciated.

  Read the article

• ARM TechCon 2013: Oracle, ARM expand collaboration on servers, Internet of Things

  - by Henrik Stahl

  If you have been following Java news, you are already aware of the fact that there has been a lot of investment in Java for ARM-based devices and servers over the last couple of years (news, more news, even more, and lots more). We have released Java ME Embedded binaries for ARM Cortex-M micro controllers, Java SE Embedded for ARM application processors, and a port of the Oracle JDK for ARM-based servers. We have been making Java available to the Beagleboard, Raspberry Pi and Lego Mindstorms/LeJOS communities and worked with them and the Java User Groups to evangelize Java as a great development environment for IoT devices. We have announced commercial relationships with Freescale, Qualcomm, Gemalto M2M, SIMCom to name a few. ARM and Freescale on their side have joined the JCP, recently been voted in as members of the Executive Committee, and have worked with Oracle to evangelize Java in their ecosystem. It is with this background, Nandini Ramani, Vice President, Java Platform at Oracle, announced a expanded collaboration with ARM in a TechCon 2013 keynote titled "Enabling Compelling Services for IoT". To summarize the announcement: ARM and Oracle will work together on interoperability between the ARM Sensinode communications stack (based on CoAP, DTLS and 6LoWPAN) and Oracle's Java ME, Java SE and middleware products. ARM will donate the Sensinode CoAP protocol engine to OpenJDK to stimulate broad adoption of the CoAP protocol, and work with Oracle to extend the relevant Java specifications with CoAP support. CoAP (Constrained Application Protocol) is an IETF specification that provides a low-bandwidth request/response protocol suitable for IoT applications. ARM will work with Oracle and Freescale to enable the mbed Hardware Abstraction Layer (HAL) to act as a portability layer for Java ME Embedded. Oracle will enable mbed as a tier one platform for Java ME Embedded. Over time, this effort will allow any mbed-enabled platforms (mostly based on Cortex-M microcontrollers) to work with off the shelf Java ME Embedded binaries, extending the reach of Java ME into IoT edge nodes. In Nandini's keynote, Oracle showed a roadmap to port the Oracle JDK for Linux on 64-bit ARMv8 servers in the 2015 time frame, preceded by an extended early access program. We expect this binary to have full feature parity with Oracle JDK on other platforms, and be available under the same royalty-free license. This effort has been going on for some time, but is now accelerated due to availability of hardware from Applied Micro. Oracle will be working with Applied Micro on the ARMv8 port, and on optimizing Java for their X-Gene products. Oracle and ARM will work closely on IoT architecture, and on evangelizing Java on ARM for both servers and IoT devices. These announcements reinforce Java's position as a first-class citizen in the ARM ecosystem, and signal a commitment from us to collaborate on driving standards and open ecosystem for the Internet of Things. If you are active in this area and not already in touch with us, or interested in learning more - please reach out to us!

  Read the article

• Live Mail folder and Thunderbird

  - by Umair Mustafa

  Me Friends Hello, Guys I'm facing a small issue and that is, I created a New account(MS live Email account) on Thunderbird and set the incoming protocol to IMAP and "pop3.live.com" Port No 995 , SSL to SSL/TLS and Outgoing protocol to SMTP and "smtp.live.com" Port No 25 , SSL to STARTTLS Now What I want is that there are sub folders in my Web based Live Email account which are not appearing when I create the account in Thunderbird. Please tell me how to get this thing done

  Read the article

• Payments - Chase Paymentech PTK Decomissioning FTP After July 2014

  - by LuciaC

  Customers who have integrated Oracle Payments with Chase Paymentech payment system are being contacted by Paymentech informing them about the impending desupport of standard File Transfer Protocol (FTP).  Customers are being advised to look for alternate protocol to connect to Paymentech for credit card and direct debit payment processing.  Oracle Payments product management and development is aware of Paymentech PTK decomissioning FTP after July 2014. They are currently evaluating using SFTP as an alternative.  Please monitor Doc ID 1586425.1 for the latest updates.

  Read the article

• How to find an ip of connected vnc client from vncserver log?

  - by Kittipat Tatsanakit

  I run the vncserver using vncserver:1 I take a look in ~/.vnc/ubuntu:1.log I only show something like this. Sat Oct 6 20:40:12 2012 Connections: accepted: 0.0.0.0::2043 SConnection: Client needs protocol version 3.8 SConnection: Client requests security type VncAuth(2) Sat Oct 6 20:40:14 2012 SConnection: AuthFailureException: Authentication failure Connections: closed: 0.0.0.0::2043 (Authentication failure) Sat Oct 6 20:40:16 2012 Connections: accepted: 0.0.0.0::2048 SConnection: Client needs protocol version 3.8 SConnection: Client requests security type VncAuth(2) How do I find the ip of connected vnc client?

  Read the article

• Welcome to ubiquitous file sharing (December 08, 2009)

  - by user12612012

  The core of any file server is its file system and ZFS provides the foundation on which we have built our ubiquitous file sharing and single access control model.  ZFS has a rich, Windows and NFSv4 compatible, ACL implementation (ZFS only uses ACLs), it understands both UNIX IDs and Windows SIDs and it is integrated with the identity mapping service; it knows when a UNIX/NIS user and a Windows user are equivalent, and similarly for groups.  We have a single access control architecture, regardless of whether you are accessing the system via NFS or SMB/CIFS.The NFS and SMB protocol services are also integrated with the identity mapping service and shares are not restricted to UNIX permissions or Windows permissions.  All access control is performed by ZFS, the system can always share file systems simultaneously over both protocols and our model is native access to any share from either protocol.Modal architectures have unnecessary restrictions, confusing rules, administrative overhead and weird deployments to try to make them work; they exist as a compromise not because they offer a benefit.  Having some shares that only support UNIX permissions, others that only support ACLs and some that support both in a quirky way really doesn't seem like the sort of thing you'd want in a multi-protocol file server.  Perhaps because the server has been built on a file system that was designed for UNIX permissions, possibly with ACL support bolted on as an add-on afterthought, or because the protocol services are not truly integrated with the operating system, it may not be capable of supporting a single integrated model.With a single, integrated sharing and access control model: If you connect from Windows or another SMB/CIFS client: The system creates a credential containing both your Windows identity and your UNIX/NIS identity.  The credential includes UNIX/NIS IDs and SIDs, and UNIX/NIS groups and Windows groups. If your Windows identity is mapped to an ephemeral ID, files created by you will be owned by your Windows identity (ZFS understands both UNIX IDs and Windows SIDs). If your Windows identity is mapped to a real UNIX/NIS UID, files created by you will be owned by your UNIX/NIS identity. If you access a file that you previously created from UNIX, the system will map your UNIX identity to your Windows identity and recognize that you are the owner.  Identity mapping also supports access checking if you are being assessed for access via the ACL. If you connect via NFS (typically from a UNIX client): The system creates a credential containing your UNIX/NIS identity (including groups). Files you create will be owned by your UNIX/NIS identity. If you access a file that you previously created from Windows and the file is owned by your UID, no mapping is required. Otherwise the system will map your Windows identity to your UNIX/NIS identity and recognize that you are the owner.  Again, mapping is fully supported during ACL processing. The NFS, SMB/CIFS and ZFS services all work cooperatively to ensure that your UNIX identity and your Windows identity are equivalent when you access the system.  This, along with the single ACL-based access control implementation, results in a system that provides that elusive ubiquitous file sharing experience.

  Read the article

• TLS/SSL and .NET Framework 4.0

  The Secure Socket Layer is now essential for the secure exchange of digital data, and is most generally used within the HTTPS protocol. .NET now provides the Windows Communication Foundation (WCF) to implement secure communications directly. Matteo explains the TLS/SSL protocol, and takes a hands-on approach to investigate the SslStream class to show how to implement a secure communication channel

  Read the article

• Configure SQL Express 2005 for remote access

  Please follow the below steps as shown in pictures to configure SQL Server Express 2005 for remote access. Fig1: Open SQL Serve Configuration Manager Fig2: Navigate to SQL Serve 2005 N/W configuration and click on Protocols node Fig3: Enable TCP/IP Protocol Fig4: Enable Named Pipes Protocol Fig5: After enabling TCP/IP and Named Pipes protocols Fig6: Finally click on TCP/IP to configure the port number to listen N/W requests to SQL Express 2005. span.fullpost {display:none;}

  Read the article

• RIA Services - exposing OData service

  Open Data Protocol (OData) is a web protocol which is used for querying and updating data. In this article we will see how to enable OData service in our RIA services.

  Read the article

• Unable to start Tomcat6 with HTTPS enabled

  - by ram

  I have the following server.xml settings for my tomcat6 server <!-- COMMENTED <Connector port="8080" maxThreads="150" enableLookups="false" acceptCount="100" scheme="http" redirectPort="8443"/> --> <!-- COMMENTED <Connector port="80" maxThreads="150" enableLookups="false" acceptCount="100" scheme="http" redirectPort="443"/> --> <Connector port="443" maxHttpHeaderSize="8192" maxThreads="150" enableLookups="false" disableUploadTimeout="true" acceptCount="100" scheme="https" secure="true" SSLEnabled="true" SSLCertificateFile="%SSL_CERT%" SSLCertificateKeyFile="%SSL_KEY%" SSLCipherSuite="ALL:!ADH:!kEDH:!SSLv2:!EXPORT40:!EXP:!LOW" compression="on" compressableMimeType="text/html,text/xml,text/plain,application/javascript,application/json,text/javascript"/> Complete server.xml is here but when I try to start the application I get the following error in catalina.*.log file INFO: Initializing Coyote HTTP/1.1 on http-80 Apr 7, 2013 8:38:38 PM org.apache.coyote.http11.Http11AprProtocol init SEVERE: Error initializing endpoint java.lang.Exception: Invalid Server SSL Protocol (error:00000000:lib(0):func(0):reason(0)) at org.apache.tomcat.jni.SSLContext.make(Native Method) at org.apache.tomcat.util.net.AprEndpoint.init(AprEndpoint.java:729) at org.apache.coyote.http11.Http11AprProtocol.init(Http11AprProtocol.java:107) at org.apache.catalina.connector.Connector.initialize(Connector.java:1049) at org.apache.catalina.core.StandardService.initialize(StandardService.java:703) at org.apache.catalina.core.StandardServer.initialize(StandardServer.java:838) at org.apache.catalina.startup.Catalina.load(Catalina.java:538) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Apr 7, 2013 8:38:38 PM org.apache.catalina.core.StandardService initialize SEVERE: Failed to initialize connector [Connector[HTTP/1.1-443]] LifecycleException: Protocol handler initialization failed: java.lang.Exception: Invalid Server SSL Protocol (error:00000000:lib(0):func(0):reason(0)) at org.apache.catalina.connector.Connector.initialize(Connector.java:1051) at org.apache.catalina.core.StandardService.initialize(StandardService.java:703) at org.apache.catalina.core.StandardServer.initialize(StandardServer.java:838) at org.apache.catalina.startup.Catalina.load(Catalina.java:538) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) I've checked the following things already I have given read permissions for everyone for .crt and .key files I copied server.xml to a different working tomcat6 server and it works there, server.xml from the mentioned working tomcat5 webserver doesn't work here and it fails with the same error Works well with just HTTP enabled explicitly mentioning protocol in the Connector i.e. protocol="org.apache.coyote.http11.Http11AprProtocol" results in the same exception Please help me if I am missing something. Thanks in advance

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Windows 2008 R2 IPsec encryption in tunnel mode, hosts in same subnet

  - by fission

  In Windows there appear to be two ways to set up IPsec: The IP Security Policy Management MMC snap-in (part of secpol.msc, introduced in Windows 2000). The Windows Firewall with Advanced Security MMC snap-in (wf.msc, introduced in Windows 2008/Vista). My question concerns #2 – I already figured out what I need to know for #1. (But I want to use the ‘new’ snap-in for its improved encryption capabilities.) I have two Windows Server 2008 R2 computers in the same domain (domain members), on the same subnet: server2 172.16.11.20 server3 172.16.11.30 My goal is to encrypt all communication between these two machines using IPsec in tunnel mode, so that the protocol stack is: IP ESP IP …etc. First, on each computer, I created a Connection Security Rule: Endpoint 1: (local IP address), eg 172.16.11.20 for server2 Endpoint 2: (remote IP address), eg 172.16.11.30 Protocol: Any Authentication: Require inbound and outbound, Computer (Kerberos V5) IPsec tunnel: Exempt IPsec protected connections Local tunnel endpoint: Any Remote tunnel endpoint: (remote IP address), eg 172.16.11.30 At this point, I can ping each machine, and Wireshark shows me the protocol stack; however, nothing is encrypted (which is expected at this point). I know that it's unencrypted because Wireshark can decode it (using the setting Attempt to detect/decode NULL encrypted ESP payloads) and the Monitor Security Associations Quick Mode display shows ESP Encryption: None. Then on each server, I created Inbound and Outbound Rules: Protocol: Any Local IP addresses: (local IP address), eg 172.16.11.20 Remote IP addresses: (remote IP address), eg 172.16.11.30 Action: Allow the connection if it is secure Require the connections to be encrypted The problem: Though I create the Inbound and Outbound Rules on each server to enable encryption, the data is still going over the wire (wrapped in ESP) with NULL encryption. (You can see this in Wireshark.) When the arrives at the receiving end, it's rejected (presumably because it's unencrypted). [And, disabling the Inbound rule on the receiving end causes it to lock up and/or bluescreen – fun!] The Windows Firewall log says, eg: 2014-05-30 22:26:28 DROP ICMP 172.16.11.20 172.16.11.30 - - 60 - - - - 8 0 - RECEIVE I've tried varying a few things: In the Rules, setting the local IP address to Any Toggling the Exempt IPsec protected connections setting Disabling rules (eg disabling one or both sets of Inbound or Outbound rules) Changing the protocol (eg to just TCP) But realistically there aren't that many knobs to turn. Does anyone have any ideas? Has anyone tried to set up tunnel mode between two hosts using Windows Firewall? I've successfully got it set up in transport mode (ie no tunnel) using exactly the same set of rules, so I'm a bit surprised that it didn't Just Work™ with the tunnel added.

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• SSH: Port Forwarding, Firewalls, & Plesk

  - by Kian Mayne

  I edited my SSH configuration to accept connections on Port 213, as it was one of the few ports that my work firewall allows through. I then restarted sshd and everything was going well. I tested the ssh server locally, and checked the sshd service was listening on port 213; however, I still cannot get it to work outside of localhost. PuTTY gives a connection refused message, and some of the sites that allow check of ports I tried said the port was closed. To me, this is either firewall or port forwarding. But I've already added inbound and outbound exceptions for it. Is this a problem with my server host, or is there something I've missed? My full SSH config file, as requested: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 Port 213 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• What is the difference between an Abstract Syntax Tree and a Concrete Syntax Tree?

  - by Jason Baker

  I've been reading a bit about how interpreters/compilers work, and one area where I'm getting confused is the difference between an AST and a CST. My understanding is that the parser makes a CST, hands it to the semantic analyzer which turns it into an AST. However, my understanding is that the semantic analyzer simply ensures that rules are followed. I don't really understand why it would actually make any changes to make it abstract rather than concrete. Is there something that I'm missing about the semantic analyzer, or is the difference between an AST and CST somewhat artificial?

  Read the article

• Convert Chunk of Data into Tabular Format Using Perl

  - by neversaint

  I have a data that looks like this 1:SRX000566 Submitter: WoldLab Study: RNASeq expression profiling for ENCODE project(SRP000228) Sample: Human cell line GM12878(SRS000567) Instrument: Solexa 1G Genome Analyzer Total: 4 runs, 62.7M spots, 2.1G bases Run #1: SRR002055, 11373440 spots, 375323520 bases Run #2: SRR002063, 22995209 spots, 758841897 bases Run #3: SRR005091, 13934766 spots, 459847278 bases Run #4: SRR005096, 14370900 spots, 474239700 bases 2:SRX000565 Submitter: WoldLab Study: RNASeq expression profiling for ENCODE project(SRP000228) Sample: Human cell line GM12878(SRS000567) Instrument: Solexa 1G Genome Analyzer Total: 3 runs, 51.2M spots, 1.7G bases Run #1: SRR002052, 12607931 spots, 416061723 bases Run #2: SRR002054, 12880281 spots, 425049273 bases Run #3: SRR002060, 25740337 spots, 849431121 bases 3:SRX012407 Submitter: GEO Study: GSE17153: Illumina sequencing of small RNAs from C. elegans embryos(SRP001363) Sample: Caenorhabditis elegans(SRS006961) Instrument: Illumina Genome Analyzer II Total: 1 run, 3M spots, 106.8M bases Run #1: SRR029428, 2965597 spots, 106761492 bases Is there a compact way to convert them into tabular format (tab separated). Hence 1 entry/row per chunk. In these case 3 rows. I tried this but doesn't seem to work. perl -laF/\n/ -000ne"print join chr(9),@F" myfile.txt

  Read the article

• Using Nortel Netdirect on Windows 7 64bit

  - by Matt Lewis

  Does anyone know how to use Nortel Netdirect (Version 7.1.3.0) with Windows 7 64 bit (Home Premium)? There are several ways available to me for connecting, all of which work for me on a 32-bit XP machine: Nortel Contivity VPN client (v6_02.022). The installer appears to be 16-bit, so I can't even install it on a 64-bit machine. Web-based SSL via IE Web-based SSL via Firefox The Web-based SSL process is supposed to load Netdirect and start it up, establishing the VPN connection. Using Firefox, I'm able to authenticate with my smartcard, but when it tries to download the applet, the process stops with a message box saying that it couldn't download the zip file. If I run Firefox in Vista compatibility mode, it gets a little farther, and manages to start Netdirect, but then exits after notifying me that the netdirect adapter was not installed. Using IE, I'm able to authenticate with my smartcard, then the java applet starts, but dies with the following sent to the java console: load: class NetDirect not found. java.lang.ClassNotFoundException: NetDirect at sun.plugin2.applet.Applet2ClassLoader.findClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) at sun.plugin2.applet.Plugin2ClassLoader.loadCode(Unknown Source) at sun.plugin2.applet.Plugin2Manager.createApplet(Unknown Source) at sun.plugin2.applet.Plugin2Manager$AppletExecutionRunnable.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Caused by: javax.net.ssl.SSLHandshakeException: Received fatal alert: unknown_ca at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source) at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.recvAlert(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.startHandshake(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.startHandshake(Unknown Source) at sun.net.www.protocol.https.HttpsClient.afterConnect(Unknown Source) at sun.net.www.protocol.https.AbstractDelegateHttpsURLConnection.connect(Unknown Source) at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source) at java.net.HttpURLConnection.getResponseCode(Unknown Source) at sun.net.www.protocol.https.HttpsURLConnectionImpl.getResponseCode(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader.getBytes(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader.access$000(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader$1.run(Unknown Source) at java.security.AccessController.doPrivileged(Native Method) ... 7 more Exception: java.lang.ClassNotFoundException: NetDirect I've tried installing certificates using java's keytool, but that didn't change the outcome.

  Read the article

• How to add commands of windows to local shell of XShell 4

  - by dylanninin

  XShell is a very powerful tools to ssh remote computers such as Unix/Linux. And it has built some internal commands for you to run within your Windows. Xshell:\> help Internal Commands: new: Creates a new session. open: Opens a session or the session dialog box. edit: Opens the Session Property dialog box for a session. list: Lists information of all available sessions. 'ls' and 'dir' do the same. cd: Changes the current working directory. clear: Clears the screen/address/command history. help: Displays this help. '?' does the same. quit: Quits Local Shell. 'exit' does the same. ssh: Connects to a host using the SSH protocol. telnet: Connects to a host using the TELNET protocol. rlogin: Connects to a host using the RLOGIN protocol. sftp: Connects to a host to transfer files securely. ftp: Connects to a host to transfer files. External Commands: ipconfig: Configures TCP/IP network interfaces. ping: Sends ICMP ECHO_REQUEST packets to network hosts. tracert: Prints the route packets take to network host. netstat: Displays current protocol statistics and current TCP/IP network connections. nslookup: Resolves a hostname to IP address. For more information, type 'help command' for each command. ex) help telnet But these commands are limited, so how to add commands of windows to local shell of XShell 4

  Read the article

• Problem using a public key when connecting to a SSH server running on Cygwin

  - by binary255

  We have installed Cygwin on a Windows Server 2008 Standard server and it working pretty well. Unfortunately we still have a big problem. We want to connect using a public key through SSH which doesn't work. It always falls back to using password login. We have appended our public key to ~/.ssh/authorized_keys on the server and we have our private and public key in ~/.ssh/id_dsa respective ~/.ssh/id_dsa.pub on the client. When debugging the SSH login session we see that the key is offered by the server apparently rejects it by some unknown reason. The SSH output when connecting from an Ubuntu 9.10 desktop with debug information enabled: $ ssh -v 192.168.10.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /home/myuseraccount/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for debug1: Connecting to 192.168.10.11 [192.168.10.11] port 22. debug1: Connection established. debug1: identity file /home/myuseraccount/.ssh/identity type -1 debug1: identity file /home/myuseraccount/.ssh/id_rsa type -1 debug1: identity file /home/myuseraccount/.ssh/id_dsa type 2 debug1: Checking blacklist file /usr/share/ssh/blacklist.DSA-1024 debug1: Checking blacklist file /etc/ssh/blacklist.DSA-1024 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '192.168.10.11' is known and matches the RSA host key. debug1: Found key in /home/myuseraccount/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: /home/myuseraccount/.ssh/id_dsa debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: /home/myuseraccount/.ssh/identity debug1: Trying private key: /home/myuseraccount/.ssh/id_rsa debug1: Next authentication method: keyboard-interactive debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: password [email protected]'s password: The version of Cygwin: $ uname -a CYGWIN_NT-6.0 servername 1.7.1(0.218/5/3) 2009-12-07 11:48 i686 Cygwin The installed packages: $ cygcheck -c Cygwin Package Information Package Version Status _update-info-dir 00871-1 OK alternatives 1.3.30c-10 OK arj 3.10.22-1 OK aspell 0.60.5-1 OK aspell-en 6.0.0-1 OK aspell-sv 0.50.2-2 OK autossh 1.4b-1 OK base-cygwin 2.1-1 OK base-files 3.9-3 OK base-passwd 3.1-1 OK bash 3.2.49-23 OK bash-completion 1.1-2 OK bc 1.06-2 OK bzip2 1.0.5-10 OK cabextract 1.1-1 OK compface 1.5.2-1 OK coreutils 7.0-2 OK cron 4.1-59 OK crypt 1.1-1 OK csih 0.9.1-1 OK curl 7.19.6-1 OK cvs 1.12.13-10 OK cvsutils 0.2.5-1 OK cygrunsrv 1.34-1 OK cygutils 1.4.2-1 OK cygwin 1.7.1-1 OK cygwin-doc 1.5-1 OK cygwin-x-doc 1.1.0-1 OK dash 0.5.5.1-2 OK diffutils 2.8.7-2 OK doxygen 1.6.1-2 OK e2fsprogs 1.35-3 OK editrights 1.01-2 OK emacs 23.1-10 OK emacs-X11 23.1-10 OK file 5.04-1 OK findutils 4.5.5-1 OK flip 1.19-1 OK font-adobe-dpi75 1.0.1-1 OK font-alias 1.0.2-1 OK font-encodings 1.0.3-1 OK font-misc-misc 1.1.0-1 OK fontconfig 2.8.0-1 OK gamin 0.1.10-10 OK gawk 3.1.7-1 OK gettext 0.17-11 OK gnome-icon-theme 2.28.0-1 OK grep 2.5.4-2 OK groff 1.19.2-2 OK gvim 7.2.264-1 OK gzip 1.3.12-2 OK hicolor-icon-theme 0.11-1 OK inetutils 1.5-6 OK ipc-utils 1.0-1 OK keychain 2.6.8-1 OK less 429-1 OK libaspell15 0.60.5-1 OK libatk1.0_0 1.28.0-1 OK libaudio2 1.9.2-1 OK libbz2_1 1.0.5-10 OK libcairo2 1.8.8-1 OK libcurl4 7.19.6-1 OK libdb4.2 4.2.52.5-2 OK libdb4.5 4.5.20.2-2 OK libexpat1 2.0.1-1 OK libfam0 0.1.10-10 OK libfontconfig1 2.8.0-1 OK libfontenc1 1.0.5-1 OK libfreetype6 2.3.12-1 OK libgcc1 4.3.4-3 OK libgdbm4 1.8.3-20 OK libgdk_pixbuf2.0_0 2.18.6-1 OK libgif4 4.1.6-10 OK libGL1 7.6.1-1 OK libglib2.0_0 2.22.4-2 OK libglitz1 0.5.6-10 OK libgmp3 4.3.1-3 OK libgtk2.0_0 2.18.6-1 OK libICE6 1.0.6-1 OK libiconv2 1.13.1-1 OK libidn11 1.16-1 OK libintl3 0.14.5-1 OK libintl8 0.17-11 OK libjasper1 1.900.1-1 OK libjbig2 2.0-11 OK libjpeg62 6b-21 OK libjpeg7 7-10 OK liblzma1 4.999.9beta-10 OK libncurses10 5.7-18 OK libncurses8 5.5-10 OK libncurses9 5.7-16 OK libopenldap2_3_0 2.3.43-1 OK libpango1.0_0 1.26.2-1 OK libpcre0 8.00-1 OK libpixman1_0 0.16.6-1 OK libpng12 1.2.35-10 OK libpopt0 1.6.4-4 OK libpq5 8.2.11-1 OK libreadline6 5.2.14-12 OK libreadline7 6.0.3-2 OK libsasl2 2.1.19-3 OK libSM6 1.1.1-1 OK libssh2_1 1.2.2-1 OK libssp0 4.3.4-3 OK libstdc++6 4.3.4-3 OK libtiff5 3.9.2-1 OK libwrap0 7.6-20 OK libX11_6 1.3.3-1 OK libXau6 1.0.5-1 OK libXaw3d7 1.5D-8 OK libXaw7 1.0.7-1 OK libxcb-render-util0 0.3.6-1 OK libxcb-render0 1.5-1 OK libxcb1 1.5-1 OK libXcomposite1 0.4.1-1 OK libXcursor1 1.1.10-1 OK libXdamage1 1.1.2-1 OK libXdmcp6 1.0.3-1 OK libXext6 1.1.1-1 OK libXfixes3 4.0.4-1 OK libXft2 2.1.14-1 OK libXi6 1.3-1 OK libXinerama1 1.1-1 OK libxkbfile1 1.0.6-1 OK libxml2 2.7.6-1 OK libXmu6 1.0.5-1 OK libXmuu1 1.0.5-1 OK libXpm4 3.5.8-1 OK libXrandr2 1.3.0-10 OK libXrender1 0.9.5-1 OK libXt6 1.0.7-1 OK links 1.00pre20-1 OK login 1.10-10 OK luit 1.0.5-1 OK lynx 2.8.5-4 OK man 1.6e-1 OK minires 1.02-1 OK mkfontdir 1.0.5-1 OK mkfontscale 1.0.7-1 OK openssh 5.4p1-1 OK openssl 0.9.8m-1 OK patch 2.5.8-9 OK patchutils 0.3.1-1 OK perl 5.10.1-3 OK rebase 3.0.1-1 OK run 1.1.12-11 OK screen 4.0.3-5 OK sed 4.1.5-2 OK shared-mime-info 0.70-1 OK tar 1.22.90-1 OK terminfo 5.7_20091114-13 OK terminfo0 5.5_20061104-11 OK texinfo 4.13-3 OK tidy 041206-1 OK time 1.7-2 OK tzcode 2009k-1 OK unzip 6.0-10 OK util-linux 2.14.1-1 OK vim 7.2.264-2 OK wget 1.11.4-4 OK which 2.20-2 OK wput 0.6.1-2 OK xauth 1.0.4-1 OK xclipboard 1.1.0-1 OK xcursor-themes 1.0.2-1 OK xemacs 21.4.22-1 OK xemacs-emacs-common 21.4.22-1 OK xemacs-sumo 2007-04-27-1 OK xemacs-tags 21.4.22-1 OK xeyes 1.1.0-1 OK xinit 1.2.1-1 OK xinput 1.5.0-1 OK xkbcomp 1.1.1-1 OK xkeyboard-config 1.8-1 OK xkill 1.0.2-1 OK xmodmap 1.0.4-1 OK xorg-docs 1.5-1 OK xorg-server 1.7.6-2 OK xrdb 1.0.6-1 OK xset 1.1.0-1 OK xterm 255-1 OK xz 4.999.9beta-10 OK zip 3.0-11 OK zlib 1.2.3-10 OK zlib-devel 1.2.3-10 OK zlib0 1.2.3-10 OK The ssh deamon configuration file: $ cat /etc/sshd_config # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/bin:/usr/sbin:/sbin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh_host_rsa_key #HostKey /etc/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes StrictModes no #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. #UsePAM no AllowAgentForwarding yes AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes X11DisplayOffset 10 X11UseLocalhost no #PrintMotd yes #PrintLastLog yes TCPKeepAlive yes #UseLogin no UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /usr/sbin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs #X11Forwarding yes #AllowTcpForwarding yes #ForceCommand cvs server I hope this information is enough to solve the problem. In case any more is needed please comment and I'll add it. Thank you for reading!

  Read the article

• Problem using a public key when connecting to a SSH server running on Cygwin

  - by Deleted

  We have installed Cygwin on a Windows Server 2008 Standard server and it working pretty well. Unfortunately we still have a big problem. We want to connect using a public key through SSH which doesn't work. It always falls back to using password login. We have appended our public key to ~/.ssh/authorized_keys on the server and we have our private and public key in ~/.ssh/id_dsa respective ~/.ssh/id_dsa.pub on the client. When debugging the SSH login session we see that the key is offered by the server apparently rejects it by some unknown reason. The SSH output when connecting from an Ubuntu 9.10 desktop with debug information enabled: $ ssh -v 192.168.10.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /home/myuseraccount/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for debug1: Connecting to 192.168.10.11 [192.168.10.11] port 22. debug1: Connection established. debug1: identity file /home/myuseraccount/.ssh/identity type -1 debug1: identity file /home/myuseraccount/.ssh/id_rsa type -1 debug1: identity file /home/myuseraccount/.ssh/id_dsa type 2 debug1: Checking blacklist file /usr/share/ssh/blacklist.DSA-1024 debug1: Checking blacklist file /etc/ssh/blacklist.DSA-1024 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '192.168.10.11' is known and matches the RSA host key. debug1: Found key in /home/myuseraccount/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: /home/myuseraccount/.ssh/id_dsa debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: /home/myuseraccount/.ssh/identity debug1: Trying private key: /home/myuseraccount/.ssh/id_rsa debug1: Next authentication method: keyboard-interactive debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: password [email protected]'s password: The version of Cygwin: $ uname -a CYGWIN_NT-6.0 servername 1.7.1(0.218/5/3) 2009-12-07 11:48 i686 Cygwin The installed packages: $ cygcheck -c Cygwin Package Information Package Version Status _update-info-dir 00871-1 OK alternatives 1.3.30c-10 OK arj 3.10.22-1 OK aspell 0.60.5-1 OK aspell-en 6.0.0-1 OK aspell-sv 0.50.2-2 OK autossh 1.4b-1 OK base-cygwin 2.1-1 OK base-files 3.9-3 OK base-passwd 3.1-1 OK bash 3.2.49-23 OK bash-completion 1.1-2 OK bc 1.06-2 OK bzip2 1.0.5-10 OK cabextract 1.1-1 OK compface 1.5.2-1 OK coreutils 7.0-2 OK cron 4.1-59 OK crypt 1.1-1 OK csih 0.9.1-1 OK curl 7.19.6-1 OK cvs 1.12.13-10 OK cvsutils 0.2.5-1 OK cygrunsrv 1.34-1 OK cygutils 1.4.2-1 OK cygwin 1.7.1-1 OK cygwin-doc 1.5-1 OK cygwin-x-doc 1.1.0-1 OK dash 0.5.5.1-2 OK diffutils 2.8.7-2 OK doxygen 1.6.1-2 OK e2fsprogs 1.35-3 OK editrights 1.01-2 OK emacs 23.1-10 OK emacs-X11 23.1-10 OK file 5.04-1 OK findutils 4.5.5-1 OK flip 1.19-1 OK font-adobe-dpi75 1.0.1-1 OK font-alias 1.0.2-1 OK font-encodings 1.0.3-1 OK font-misc-misc 1.1.0-1 OK fontconfig 2.8.0-1 OK gamin 0.1.10-10 OK gawk 3.1.7-1 OK gettext 0.17-11 OK gnome-icon-theme 2.28.0-1 OK grep 2.5.4-2 OK groff 1.19.2-2 OK gvim 7.2.264-1 OK gzip 1.3.12-2 OK hicolor-icon-theme 0.11-1 OK inetutils 1.5-6 OK ipc-utils 1.0-1 OK keychain 2.6.8-1 OK less 429-1 OK libaspell15 0.60.5-1 OK libatk1.0_0 1.28.0-1 OK libaudio2 1.9.2-1 OK libbz2_1 1.0.5-10 OK libcairo2 1.8.8-1 OK libcurl4 7.19.6-1 OK libdb4.2 4.2.52.5-2 OK libdb4.5 4.5.20.2-2 OK libexpat1 2.0.1-1 OK libfam0 0.1.10-10 OK libfontconfig1 2.8.0-1 OK libfontenc1 1.0.5-1 OK libfreetype6 2.3.12-1 OK libgcc1 4.3.4-3 OK libgdbm4 1.8.3-20 OK libgdk_pixbuf2.0_0 2.18.6-1 OK libgif4 4.1.6-10 OK libGL1 7.6.1-1 OK libglib2.0_0 2.22.4-2 OK libglitz1 0.5.6-10 OK libgmp3 4.3.1-3 OK libgtk2.0_0 2.18.6-1 OK libICE6 1.0.6-1 OK libiconv2 1.13.1-1 OK libidn11 1.16-1 OK libintl3 0.14.5-1 OK libintl8 0.17-11 OK libjasper1 1.900.1-1 OK libjbig2 2.0-11 OK libjpeg62 6b-21 OK libjpeg7 7-10 OK liblzma1 4.999.9beta-10 OK libncurses10 5.7-18 OK libncurses8 5.5-10 OK libncurses9 5.7-16 OK libopenldap2_3_0 2.3.43-1 OK libpango1.0_0 1.26.2-1 OK libpcre0 8.00-1 OK libpixman1_0 0.16.6-1 OK libpng12 1.2.35-10 OK libpopt0 1.6.4-4 OK libpq5 8.2.11-1 OK libreadline6 5.2.14-12 OK libreadline7 6.0.3-2 OK libsasl2 2.1.19-3 OK libSM6 1.1.1-1 OK libssh2_1 1.2.2-1 OK libssp0 4.3.4-3 OK libstdc++6 4.3.4-3 OK libtiff5 3.9.2-1 OK libwrap0 7.6-20 OK libX11_6 1.3.3-1 OK libXau6 1.0.5-1 OK libXaw3d7 1.5D-8 OK libXaw7 1.0.7-1 OK libxcb-render-util0 0.3.6-1 OK libxcb-render0 1.5-1 OK libxcb1 1.5-1 OK libXcomposite1 0.4.1-1 OK libXcursor1 1.1.10-1 OK libXdamage1 1.1.2-1 OK libXdmcp6 1.0.3-1 OK libXext6 1.1.1-1 OK libXfixes3 4.0.4-1 OK libXft2 2.1.14-1 OK libXi6 1.3-1 OK libXinerama1 1.1-1 OK libxkbfile1 1.0.6-1 OK libxml2 2.7.6-1 OK libXmu6 1.0.5-1 OK libXmuu1 1.0.5-1 OK libXpm4 3.5.8-1 OK libXrandr2 1.3.0-10 OK libXrender1 0.9.5-1 OK libXt6 1.0.7-1 OK links 1.00pre20-1 OK login 1.10-10 OK luit 1.0.5-1 OK lynx 2.8.5-4 OK man 1.6e-1 OK minires 1.02-1 OK mkfontdir 1.0.5-1 OK mkfontscale 1.0.7-1 OK openssh 5.4p1-1 OK openssl 0.9.8m-1 OK patch 2.5.8-9 OK patchutils 0.3.1-1 OK perl 5.10.1-3 OK rebase 3.0.1-1 OK run 1.1.12-11 OK screen 4.0.3-5 OK sed 4.1.5-2 OK shared-mime-info 0.70-1 OK tar 1.22.90-1 OK terminfo 5.7_20091114-13 OK terminfo0 5.5_20061104-11 OK texinfo 4.13-3 OK tidy 041206-1 OK time 1.7-2 OK tzcode 2009k-1 OK unzip 6.0-10 OK util-linux 2.14.1-1 OK vim 7.2.264-2 OK wget 1.11.4-4 OK which 2.20-2 OK wput 0.6.1-2 OK xauth 1.0.4-1 OK xclipboard 1.1.0-1 OK xcursor-themes 1.0.2-1 OK xemacs 21.4.22-1 OK xemacs-emacs-common 21.4.22-1 OK xemacs-sumo 2007-04-27-1 OK xemacs-tags 21.4.22-1 OK xeyes 1.1.0-1 OK xinit 1.2.1-1 OK xinput 1.5.0-1 OK xkbcomp 1.1.1-1 OK xkeyboard-config 1.8-1 OK xkill 1.0.2-1 OK xmodmap 1.0.4-1 OK xorg-docs 1.5-1 OK xorg-server 1.7.6-2 OK xrdb 1.0.6-1 OK xset 1.1.0-1 OK xterm 255-1 OK xz 4.999.9beta-10 OK zip 3.0-11 OK zlib 1.2.3-10 OK zlib-devel 1.2.3-10 OK zlib0 1.2.3-10 OK The ssh deamon configuration file: $ cat /etc/sshd_config # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/bin:/usr/sbin:/sbin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh_host_rsa_key #HostKey /etc/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes StrictModes no #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. #UsePAM no AllowAgentForwarding yes AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes X11DisplayOffset 10 X11UseLocalhost no #PrintMotd yes #PrintLastLog yes TCPKeepAlive yes #UseLogin no UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /usr/sbin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs #X11Forwarding yes #AllowTcpForwarding yes #ForceCommand cvs server I hope this information is enough to solve the problem. In case any more is needed please comment and I'll add it. Thank you for reading!

  Read the article

• Can nginx be an mail proxy for a backend server that does not accept cleartext logins?

  - by 84104

  Can Nginx be an mail proxy for a backend server that does not accept cleartext logins? Preferably I'd like to know what directive to include so that it will invoke STARTTLS/STLS, but communication via IMAPS or POP3S is sufficient. relevant(?) section of nginx.conf mail { auth_http localhost:80/mailproxy/auth.php; proxy on; ssl_prefer_server_ciphers on; ssl_protocols TLSv1 SSLv3; ssl_ciphers HIGH:!ADH:!MD5:@STRENGTH; ssl_session_cache shared:TLSSL:16m; ssl_session_timeout 10m; ssl_certificate /etc/ssl/private/hostname.crt; ssl_certificate_key /etc/ssl/private/hostname.key; imap_capabilities "IMAP4rev1" "UIDPLUS"; server { protocol imap; listen 143; starttls on; } server { protocol imap; listen 993; ssl on; } pop3_capabilities "TOP" "USER"; server { protocol pop3; listen 110; starttls on; pop3_auth plain; } server { protocol pop3; listen 995; ssl on; pop3_auth plain; } }

  Read the article

• Hyper-V VM's cannot access Host resources, and vice-versa

  - by Agent

  I have several Hyper-V vm's running on this Win2008 R2 Server box, and up until a reboot of the host server, all the VM's were able to access shared folders on the host. Now, they can't even ping the host server. From what I've seen, I need to setup an Internal only network through Virtual Network Manager in Hyper-V. I set this up, then tried to enable the Microsoft Virtual Network Switch Protocol option in this Internal Only NIC, but I get popups saying: Your current selection will also disable the following features: Microsoft virtual network switch protocol Which is absolutely stupid, considering the protocol is what I'm ticking the checkbox to Enable! As of now, on the host, I have 2 NICs: Physical - This NIC on the host machine does have the MVNS protocol enabled Virtual Network Adapter - Created through Hyper-V Virtual Network Manager as an External type of network. Trying to enable MVNS on this NIC also produces the error above. I've tried enabling Client for Microsoft Networks on the physical NIC for IPv6, but everytime I do that, all the VMs lose Internet connectivity and I cannot RDP into them. Anything else I can try?

  Read the article

• Relevance and Necessity of SNMP

  - by Adam Tannon

  Edit: I am in the process of designing a Java-based monitoring tool that will send back periodic "health checks" of a Java app deployed to a cluster of GlassFish servers. I am trying to figure out the best protocol for this monitoring tool to send information back to the monitoring server on. After an initial research effort on my part, it seems like SNMP is just a protocol for monitor-type applications to communicate the "health status" of something (a part of a network, a server, a cluster, an application, etc.) to the rest of the network. If the above is incorrect, please correct me!!! Assuming the generalization is more or less accurate, my next question is: why is this a protocol!?!? In the age of REST/SOAP/TCP protocols, why is there the need for a standardized protocol that only fits one type of application (monitoring)? In other words, if I'm a developer assigned to building a new monitoring tool that periodically polls a server and reports on its CPU and available memory, what advantages does SNMP give me over just POSTing to a RESTful API via plain 'ole HTTP? I'm sure I'm missing something here - I just need someone to help connect the dots! Thanks in advance!

  Read the article

• Enforce SSIS naming conventions using BI-xPress

  - by jamiet

  A long long long time ago (in 2006 in fact) I published a blog post entitled Suggested Best Practises and naming conventions in which I suggested a bunch of acronyms that folks could use to prefix object names in their SSIS packages, thus allowing easier identification of those objects in log records, here is a sample of some of those suggestions: If you have adopted these naming conventions (and I am led to believe that a bunch of people have) then you might like to know that you can now check for adherence to these conventions using a tool called BI-xPress from Pragmatic Works. BI-xPress includes a feature called the Best Practices Analyzer that scans your packages and assess them according to some rules that you specify. In addition Pragmatic Works have made available a collection of these rules that adhere to the naming conventions I specified in 2006 You can download this collection however I recommend you first read the accompanying article that demonstrates the capabilities of the Best Practices Analyzer. Pretty cool stuff. @Jamiet

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >