Search Results

Search found 7976 results on 320 pages for 'sl dev'.

Page 25/320 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

  • volume group disappeared after xfs_check run

    - by John P
    EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

    Read the article

  • Can't boot in Ubuntu after windows upgrade

    - by VanceAnce
    After my lastest update for Ubuntu and Windows XP, I got a Grub error on booting the next day. ls lists the following (without () ): sd0 sd1, msdos sd2 sd5 sd6 When I tried to get into one with (sd0,xy)/ it doesn't detect system or unknown file system error. I tried to boot to a live session with a Knoppix live CD and found out that all data exists. I also tried to recover with TestDisk and it finds all systems. Here is the test disk result: Start End Size in sectors 1 * HPFS - NTFS 0 1 1 7079 254 63 113740137 2 E extended LBA 7080 0 1 12161 254 63 81642330 5 L HPFS - NTFS 7080 1 1 10266 254 63 51199092 [Schule] X extended 12031 30 1 12161 254 63 2102625 6 L Linux Swap 12031 31 33 12161 254 63 2102530 I've 1 winxp-home, 1x Ubuntu (ext3+swap) and 1 winxp prof and then I wrote on mbr with TestDisk but I always get the same errors with Grub. What should I do? I need both XP and Ubuntu. Help me please. more infos in answers below - sry for thos confusing style but im working on diff live system and browsers and have to reboot always the boot info script output is also down below maybe an advanced user can correct my fail posting - after i can solve my issuse i will register here thanx and pls help me with those weired issues ! as i still cant just comment my own answer or those on top i again has to put it here as a sepperate answer..... (or even edit - maybe an browser failur using the live cds ... cause this posti can edit) here the bootinfo script output - but the result is the same as with TestDisk ... but it looks worse - cause it also doesnt detect my old ubuntu ... but there wasnt a eares process or overwrite process visibile ending the last working session output: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== = Syslinux MBR (4.04 and higher) is installed in the MBR of /dev/sda. sda1: __________________________________________ File system: ntfs Boot sector type: Windows XP: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files: /boot.ini /ntldr /NTDETECT.COM sda2: __________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________ File system: ntfs Boot sector type: Windows XP: NTFS Boot sector info: According to the info in the boot sector, sda5 starts at sector 63. Operating System: Windows XP Boot files: sda6: __________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _______________________________________ Disk /dev/sda: 100.0 GB, 100030242816 bytes 255 heads, 63 sectors/track, 12161 cylinders, total 195371568 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 63 113,740,199 113,740,137 7 NTFS / exFAT / HPFS /dev/sda2 113,740,200 195,382,529 81,642,330 f W95 Extended (LBA) /dev/sda5 113,740,263 164,939,354 51,199,092 7 NTFS / exFAT / HPFS /dev/sda6 193,280,000 195,382,529 2,102,530 82 Linux swap / Solaris /dev/sda2 ends after the last sector of /dev/sda /dev/sda6 ends after the last sector of /dev/sda "blkid" output: ____________________________________ Device UUID TYPE LABEL /dev/loop0 squashfs /dev/sda1 6596D86768011128 ntfs /dev/sda5 1300D3B7744EC141 ntfs Schule /dev/sda6 5b95f2a1-4145-43a5-ac51-41d7dd32b213 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /rofs squashfs (ro,noatime) /dev/sr0 /cdrom iso9660 (ro,noatime) ================================ sda1/boot.ini: ================================ [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Home Edition" /fastdetect /NoExecute=OptOut multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Microsoft Windows XP Professional" /fastdetect [spybotsd] timeout.old=30 the last part shows that i now use the windows boot loader so that i can acces at least one OS but shouldnt i also get acces to my ubuntu partitions with live-linux-cds ? or do i have to boot with grub to get to those files only ??

    Read the article

  • disks not ready in array causes mdadm to force initramfs shell

    - by RaidPinata
    Okay, this is starting to get pretty frustrating. I've read most of the other answers on this site that have anything to do with this issue but I'm still not getting anywhere. I have a RAID 6 array with 10 devices and 1 spare. The OS is on a completely separate device. At boot only three of the 10 devices in the raid are available, the others become available later in the boot process. Currently, unless I go through initramfs I can't get the system to boot - it just hangs with a blank screen. When I do boot through recovery (initramfs), I get a message asking if I want to assemble the degraded array. If I say no and then exit initramfs the system boots fine and my array is mounted exactly where I intend it to. Here are the pertinent files as near as I can tell. Ask me if you want to see anything else. # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default (built-in), scan all partitions (/proc/partitions) and all # containers for MD superblocks. alternatively, specify devices to scan, using # wildcards if desired. #DEVICE partitions containers # auto-create devices with Debian standard permissions # CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays # This file was auto-generated on Tue, 13 Nov 2012 13:50:41 -0700 # by mkconf $Id$ ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae Here is fstab # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sdc2 during installation UUID=3fa1e73f-3d83-4afe-9415-6285d432c133 / ext4 errors=remount-ro 0 1 # swap was on /dev/sdc3 during installation UUID=c4988662-67f3-4069-a16e-db740e054727 none swap sw 0 0 # mount large raid device on /data /dev/md0 /data ext4 defaults,nofail,noatime,nobootwait 0 0 output of cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sda[0] sdd[10](S) sdl[9] sdk[8] sdj[7] sdi[6] sdh[5] sdg[4] sdf[3] sde[2] sdb[1] 23441080320 blocks super 1.2 level 6, 512k chunk, algorithm 2 [10/10] [UUUUUUUUUU] unused devices: <none> Here is the output of mdadm --detail --scan --verbose ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae devices=/dev/sda,/dev/sdb,/dev/sde,/dev/sdf,/dev/sdg,/dev/sdh,/dev/sdi,/dev/sdj,/dev/sdk,/dev/sdl,/dev/sdd Please let me know if there is anything else you think might be useful in troubleshooting this... I just can't seem to figure out how to change the boot process so that mdadm waits until the drives are ready to build the array. Everything works just fine if the drives are given enough time to come online. edit: changed title to properly reflect situation

    Read the article

  • LVM mirror attempt results in "Insufficient free space"

    - by MattK
    Attempting to add a disk to mirror an LVM volume on CentOS 7 always fails with "Insufficient free space: 1 extents needed, but only 0 available". Having searched for a solution, I have tried specifying disks, multiple logging options, adding 3rd log partition, but have not found a solution Not sure if I am making a rookie mistake, or there is something more subtle wrong (I am more familiar with ZFS, new to using LVM): # lvconvert -m1 centos_bi/home Insufficient free space: 1 extents needed, but only 0 available # lvconvert -m1 --corelog centos_bi/home Insufficient free space: 1 extents needed, but only 0 available # lvconvert -m1 --corelog --alloc anywhere centos_bi/home Insufficient free space: 1 extents needed, but only 0 available # lvconvert -m1 --mirrorlog mirrored --alloc anywhere centos_bi/home /dev/sda2 Insufficient free space: 1 extents needed, but only 0 available # lvconvert -m1 --corelog --alloc anywhere centos_bi/home /dev/sdi2 /dev/sda2 Insufficient free space: 1 extents needed, but only 0 available The two disks are of the same size, and have identical partition layouts via "sfdisk -d /dev/sdi part_table; sfdisk /dev/sda < part_table". The current configuration is detailed below. # pvs PV VG Fmt Attr PSize PFree /dev/sda1 centos_bi lvm2 a-- 496.00m 496.00m /dev/sda2 centos_bi lvm2 a-- 465.27g 465.27g /dev/sdi2 centos_bi lvm2 a-- 465.27g 0 # vgs VG #PV #LV #SN Attr VSize VFree centos_bi 3 3 0 wz--n- 931.02g 465.75g # lvs -a -o +devices LV VG Attr LSize Pool Origin Data% Move Log Cpy%Sync Convert Devices home centos_bi -wi-ao---- 391.64g /dev/sdi2(6050) root centos_bi -wi-ao---- 50.00g /dev/sdi2(106309) swap centos_bi -wi-ao---- 23.63g /dev/sdi2(0) # pvdisplay --- Physical volume --- PV Name /dev/sdi2 VG Name centos_bi PV Size 465.27 GiB / not usable 3.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 119109 Free PE 0 Allocated PE 119109 --- Physical volume --- PV Name /dev/sda2 VG Name centos_bi PV Size 465.27 GiB / not usable 3.00 MiB Allocatable yes PE Size 4.00 MiB Total PE 119109 Free PE 119109 Allocated PE 0 --- Physical volume --- PV Name /dev/sda1 VG Name centos_bi PV Size 500.00 MiB / not usable 4.00 MiB Allocatable yes PE Size 4.00 MiB Total PE 124 Free PE 124 Allocated PE 0 # vgdisplay --- Volume group --- VG Name centos_bi System ID Format lvm2 Metadata Areas 3 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 3 Open LV 3 Max PV 0 Cur PV 3 Act PV 3 VG Size 931.02 GiB PE Size 4.00 MiB Total PE 238342 Alloc PE / Size 119109 / 465.27 GiB Free PE / Size 119233 / 465.75 GiB # lvdisplay --- Logical volume --- LV Path /dev/centos_bi/swap LV Name swap VG Name centos_bi LV Write Access read/write LV Creation host, time localhost, 2014-08-07 16:34:34 -0400 LV Status available # open 2 LV Size 23.63 GiB Current LE 6050 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:1 --- Logical volume --- LV Path /dev/centos_bi/home LV Name home VG Name centos_bi LV Write Access read/write LV Creation host, time localhost, 2014-08-07 16:34:35 -0400 LV Status available # open 1 LV Size 391.64 GiB Current LE 100259 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:2 --- Logical volume --- LV Path /dev/centos_bi/root LV Name root VG Name centos_bi LV Write Access read/write LV Creation host, time localhost, 2014-08-07 16:34:37 -0400 LV Status available # open 1 LV Size 50.00 GiB Current LE 12800 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0

    Read the article

  • Ubuntu 12.04 on Amazon EC2: /dev/xvda1 will be checked for errors at next reboot?

    - by cwd
    I'm running the lastest Ubuntu 12.04 AMI (ami-a29943cb) from Canonical on Amazon EC2 and quite often when I log in I get the message: *** /dev/xvda1 will be checked for errors at next reboot *** I have read a bunch of documentation on this and seem to understand that every so many reboots (around 37 see Mount count / Maximum mount count below) Ubuntu wants to check a disk for errors. I can see that by using dumpe2fs -h /dev/xvda1 (reference) to get information such as: Last mounted on: / Filesystem UUID: 1ad27d06-4ecf-493d-bb19-4710c3caf924 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype needs_recovery extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 524288 Block count: 2097152 Reserved block count: 104857 Free blocks: 1778055 Free inodes: 482659 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 511 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 Flex block group size: 16 Filesystem created: Tue Apr 24 03:07:48 2012 Last mount time: Thu Nov 8 03:17:58 2012 Last write time: Tue Apr 24 03:08:52 2012 Mount count: 3 Maximum mount count: 37 Last checked: Tue Apr 24 03:07:48 2012 Check interval: 15552000 (6 months) Next check after: Sun Oct 21 03:07:48 2012 Lifetime writes: 2454 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: 0a25e04c-6169-4d68-bfa6-a1acd8e39632 Journal backup: inode blocks Journal features: journal_incompat_revoke Journal size: 128M Journal length: 32768 Journal sequence: 0x0000158b Journal start: 1 I've tried these things to get rid of the message and usually the badblocks is what does it for me: Run this command and reboot: sudo touch /forcefsck Run badblocks to check the disk: badblocks /dev/sda1 Edit /etc/fstab and change the last "0" which is the fs_passno column accordingly and then reboot: The root filesystem should be specified with a fs_passno of 1, and other filesystems should have a fs_passno of 2. I don't understand: If this is a virtual drive shouldn't it be less prone to errors? Was the image created with one of the flags set? If not what is triggering it? Why is fs_passno set to 0 on Amazon EC2 Ubuntu images? This is not the first one that is like this.

    Read the article

  • Why does a bash-zenity script has that title on Unity Panel and that icon on Unity Launcher?

    - by Sadi
    I have this small bash script which helps use Infinality font rendering options via a more user-friendly Zenity window. But whenever I launch it I have this "Color Picker" title on Unity Panel together with the icon assigned for "Color Picker" utility. I wonder why and how this is happening and how I can change it? #!/bin/bash # A simple script to provide a basic, zenity-based GUI to change Infinality Style. # v.1.2 # infinality_current=`cat /etc/profile.d/infinality-settings.sh | grep "USE_STYLE=" | awk -F'"' '{print $2}'` sudo_password="$( gksudo --print-pass --message 'Provide permission to make system changes: Enter your password to start or press Cancel to quit.' -- : 2>/dev/null )" # Check for null entry or cancellation. if [[ ${?} != 0 || -z ${sudo_password} ]] then # Add a zenity message here if you want. exit 4 fi # Check that the password is valid. if ! sudo -kSp '' [ 1 ] <<<"${sudo_password}" 2>/dev/null then # Add a zenity message here if you want. exit 4 fi # menu(){ im="zenity --width=500 --height=490 --list --radiolist --title=\"Change Infinality Style\" --text=\"Current <i>Infinality Style</i> is\: <b>$infinality_current</b>\n? To <i>change</i> it, select any other option below and press <b>OK</b>\n? To <i>quit without changing</i>, press <b>Cancel</b>\" " im=$im" --column=\" \" --column \"Options\" --column \"Description\" " im=$im"FALSE \"DEFAULT\" \"Use default settings - a compromise that should please most people\" " im=$im"FALSE \"OSX\" \"Simulate OSX rendering\" " im=$im"FALSE \"IPAD\" \"Simulate iPad rendering\" " im=$im"FALSE \"UBUNTU\" \"Simulate Ubuntu rendering\" " im=$im"FALSE \"LINUX\" \"Generic Linux style - no snapping or certain other tweaks\" " im=$im"FALSE \"WINDOWS\" \"Simulate Windows rendering\" " im=$im"FALSE \"WIN7\" \"Simulate Windows 7 rendering with normal glyphs\" " im=$im"FALSE \"WINLIGHT\" \"Simulate Windows 7 rendering with lighter glyphs\" " im=$im"FALSE \"VANILLA\" \"Just subpixel hinting\" " im=$im"FALSE \"CLASSIC\" \"Infinality rendering circa 2010 - No snapping.\" " im=$im"FALSE \"NUDGE\" \"Infinality - Classic with lightly stem snapping and tweaks\" " im=$im"FALSE \"PUSH\" \"Infinality - Classic with medium stem snapping and tweaks\" " im=$im"FALSE \"SHOVE\" \"Infinality - Full stem snapping and tweaks without sharpening\" " im=$im"FALSE \"SHARPENED\" \"Infinality - Full stem snapping, tweaks, and Windows-style sharpening\" " im=$im"FALSE \"INFINALITY\" \"Infinality - Standard\" " im=$im"FALSE \"DISABLED\" \"Act without extra infinality enhancements - just subpixel hinting\" " } # option(){ choice=`echo $im | sh -` # if echo $choice | grep "DEFAULT" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"DEFAULT\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "OSX" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"OSX\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "IPAD" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"IPAD\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "UBUNTU" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"UBUNTU\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "LINUX" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"LINUX\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "WINDOWS" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"WINDOWS\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "WIN7" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"WINDOWS7\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "WINLIGHT" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"WINDOWS7LIGHT\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "VANILLA" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"VANILLA\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "CLASSIC" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"CLASSIC\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "NUDGE" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"NUDGE\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "PUSH" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"PUSH\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "SHOVE" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"SHOVE\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "SHARPENED" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"SHARPENED\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "INFINALITY" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"INFINALITY\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # if echo $choice | grep "DISABLED" > /dev/null; then sudo -Sp '' sed -i "s/USE_STYLE=\"${infinality_current}\"/USE_STYLE=\"DISABLED\"/g" '/etc/profile.d/infinality-settings.sh' <<<"${sudo_password}" fi # } # menu option # if test ${#choice} -gt 0; then echo "Operation completed" fi # exit 0

    Read the article

  • Can I expand my /boot without upsetting the system?

    - by Kaustubh P
    This is the current state of my partition table. As can be seen, the boot is very small, and I cant upgrade the kernel, because the update-manager tells me there isnt enough space on /boot :( Which effectively means that I cant update my kernel. Can I change the size of my boot, without necessitating a reinstall of either of the installed system? Filesystem Size Used Avail Use% Mounted on /dev/sda5 12G 4.9G 6.2G 45% / none 2.0G 284K 2.0G 1% /dev none 2.0G 8.5M 2.0G 1% /dev/shm none 2.0G 92K 2.0G 1% /var/run none 2.0G 0 2.0G 0% /var/lock /dev/sda3 42G 21G 22G 49% /media/Erste /dev/sda2 5.1G 2.5G 2.7G 48% /media/Swap /dev/sda1 30G 25G 4.9G 84% /media/Windows7 /dev/sda9 47G 28G 20G 60% /media/Zweite /dev/sda6 11G 7.6G 2.0G 80% /home /dev/sda8 49M 31M 16M 66% /boot

    Read the article

  • How large should I make root, home, usr, var, and tmp partitions?

    - by Teddy Okidoki
    i install ubuntu server 10.04, have 64 Gb VHD. And want to separate partitions in this mode: /dev/xvda0 p on swap (2 Gb) /dev/xvda1a0 e on /boot (128 Mb) /dev/xvda1a1 e on / type ffs (local) /dev/xvda1a2 e on /usr type ffs (local, nodev) /dev/xvda1a3 e on /tmp type ffs (local, nodev) /dev/xvda1a4 e on /var/log type ffs (local, nodev) /dev/xvda1a5 e on /var type ffs (local, nodev, nosuid) /dev/xvda1a6 e on /home type ffs (local, nodev, nosuid, with quotas) /dev/xvda2 p on /new (local, nodev, nosuid, noexec) with rest of space ~50Gb. But i'ma stuck, and don't know what size to give to each folder. Also i want to encrypt partitions. Thank you for any tips. EDIT: System need minimum size, here will be installed about 10 apps like ufw, apache,mysql, chkrootkit and so on.

    Read the article

  • GetLongPathName Undeclared

    - by iwizardpro
    When I try to compile my code with the function GetLongPathName(), the compiler tells me that the function is undeclared. I have already read the MSDN documentation located @ http://msdn.microsoft.com/en-us/library/aa364980%28VS.85%29.aspx. But, even though I included those header files, I am still getting the undeclared function error. Which header file(s) am I supposed to include when using the function? #include <Windows.h> #include <WinBase.h> #define DLLEXPORT extern "C" __declspec(dllexport) DLLEXPORT char* file_get_long(char* path_original) { long length = 0; TCHAR* buffer = NULL; if(!path_original) { return "-10"; } length = GetLongPathName(path_original, NULL, 0); if(length == 0) { return "-10"; } buffer = new TCHAR[length]; length = GetLongPathName(path_original, buffer, length); if(length == 0) { return "-10"; } return buffer; } And, if it makes a difference, I am currently compiling using Dev-C++ on a Windows Vista 64-bit.

    Read the article

  • CentOS OpenVZ fail to boot after kernel update

    - by SkechBoy
    After upgrading to latest OpenVZ kernel CentOS server won't boot. When i try go boot the latest kernel server is stuck at this point: (note that images are taken from virtual kvm) http://i.stack.imgur.com/4lusz.jpg Then i try to start the server on some old kernels and than i get this error message: kernel panic - not syncing - attempted to kill init better shown on this image: http://i.stack.imgur.com/2SReF.jpg Here is some useful information fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2995.7 GB, 2995739688960 bytes 255 heads, 63 sectors/track, 364211 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004c4e4 Device Boot Start End Blocks Id System /dev/sda1 1 523 4199044+ 82 Linux swap / Solaris /dev/sda2 524 785 2104515 83 Linux /dev/sda3 786 261869 2097157230 83 Linux /dev/sda4 261870 364211 822062115 83 Linux /etc/fstab proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/sda1 none swap sw 0 0 /dev/sda2 /boot ext3 defaults 0 0 /dev/sda3 / ext3 defaults 0 0 /dev/sda4 /home ext3 defaults 0 0 and grub config file: title OpenVZ (2.6.18-274.18.1.el5.028stab098.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.18.1.el5.028stab098.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.18.1.el5.028stab098.1.img title OpenVZ (2.6.18-274.7.1.el5.028stab095.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.7.1.el5.028stab095.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.7.1.el5.028stab095.1.img title OpenVZ (2.6.18-194.8.1.el5.028stab070.4) root (hd0,1) kernel /vmlinuz-2.6.18-194.8.1.el5.028stab070.4 ro root=/dev/sda3 vga=0x317 initrd /initrd-2.6.18-194.8.1.el5.028stab070.4.img Any help is greatly appreciated Thanks.

    Read the article

  • Creating a partitioned raid1 array for booting a debian squeeze system

    - by gucki
    I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

    Read the article

  • Backup data from RAID 1 disk out of its server

    - by Doomsday
    I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

    Read the article

  • Debian: Unable to mount a second drive as a subdirectory inside of another partition.

    - by jkndrkn
    Hello. I have the following /etc/fstab: # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/md1 / ext3 defaults,errors=remount-ro 0 1 /dev/md0 /boot ext3 defaults 0 2 /dev/md5 /home ext3 defaults 0 2 /dev/md3 /opt ext3 defaults 0 2 /dev/md6 /tmp ext3 defaults 0 2 /dev/md2 /usr ext3 defaults 0 2 /dev/md4 /var ext3 defaults 0 2 /dev/md7 none swap sw 0 0 /dev/sdc /home/httpd ext3 defaults 0 2 /dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/sdc1 /mnt/usb/backup-1 auto defaults 0 0 I am unable to get /dev/sdc/ to mount at /home/httpd/ on reboot. The /home/httpd/ directory exists. Mounting via mount -t ext3 /dev/sdc /home/httpd works just fine. Mounting via mount -a generates the following error message: mount: you must specify the filesystem type This is, incidentally, the same message that I see while booting. The error message goes away if I comment out the line in fstab starting with /dev/sdc.

    Read the article

  • Route outbound connections from local network through VPN

    - by Sharkos
    I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

    Read the article

  • FileInfo..ctor(string fileName) throwing exception: bug in SL 4.0 or .NET 4.0?

    - by Duncan Bayne
    The following test case passes in .NET 4.0: var fiT = new FileInfo("myhappyfilename"); Assert.IsNotNull(fiT); ... but fails in Silverlight 4.0 with the following error: System.ArgumentNullException: Value cannot be null. Parameter name: format at System.String.Format(IFormatProvider provider, String format, Object[] args) at System.Environment.GetResourceString(String key, Object[] values) at System.IO.FileSecurityState.EnsureState() at System.IO.FileInfo.Init(String fileName, Boolean checkHost) at System.IO.FileInfo..ctor(String fileName) Either the failure is a bug in SL 4.0, or the non-failure is a bug in .NET 4.0. Anyone know which it is? (For the record, I'm running SL 4.0 on VS 2010 RC, which may be contributing to the problem).

    Read the article

  • How can we implement change notification propagation for WPF and SL in the MVVM pattern?

    - by Firoso
    Here's an example scenario targetting MVVM WPF/SL development: View data binds to view model Property "Target" "Target" exposes a field of an object called "data" that exists in the local application model, called "Original" when "Original" changes, it should raise notification to the view model and then propogate that change notification to the View. Here are the solutions I've come up with, but I don't like any of them all that much. I'm looking for other ideas, by the time we come up with something rock solid I'm certain Microsoft will have released .NET 5 with WPF/SL extensions for better tools for MVVM development. For now the question is, "What have you done to solve this problem and how has it worked out for you?" Option 1. Proposal: Attach a handler to data's PropertyChanged event that watches for string values of properties it cares about that might have changed, and raises the appropriate notification. Why I don't like it: Changes don't bubble naturally, objects must be explicitly watched, if data changes to a new source, events must be un-registered/registered. Why I kind of like it: I get explicit control over propogation of changes, and I don't have to use any types that belong at a higher level of the application such as dependancy properties. Option 2. Proposal: Attach a handler to data's PropertyChanged event that re-raises the event across all properties using the name property name. Why I don't like it: This is essentially the same as option 1, but less intelligent, and forces me to never change my property names, as they have to be the same as the property names on data Why I kind of like it: It's very easy to set up and I don't have to think about it... Then again if I try to think, and change names to things that make sense, I shoot myself in the foot, and then I have to think about it! Option 3. Proposal: Inherit my view model from dependancy object, and notify binding sources of changes directly. Why I don't like it: I'm not even 100% sure dependancy properties/objects can DO this, it was just a thought to look into. Also I don't personally feel that WPF/SL types like Dep Obj belong at the view model level. Why I kind of like it: IF it has the capability that I'm seeking then it's a good answer! minus that pesky layering issue. Option 4. Proposal: Use a consistant agent messaging system based off of Task Parallels DataFlow Library to propogate everything through linked pipelining. Why I don't like it: I've never tried this, and somehow I think it will be lacking, plus it requires me to think about my code completely differently all the way around. Why I kind of like it: It has the possiblity of allowing me to do some VERY fun manipulations with a push based data model and using ActionBlocks as validation AND setters to then privately change view model properties and explicitly control PropertyChanged notifications.

    Read the article

  • Redirect input from one terminal to another

    - by Niki Yoshiuchi
    I have sshed into a linux box and I'm using dvtm and bash (although I have also tried this with Gnu screen and bash). I have two terminals, current /dev/pts/29 and /dev/pts/130. I want to redirect the input from one to the other. From what I understand, in /dev/pts/130 I can type: cat </dev/pts/29 And then when I type in /dev/pts/29 the characters I type should show up in /dev/pts/130. However what ends up happening is that every other character I type gets redirected. For example, if I type "hello" I get this: /dev/pts/29 | /dev/pts/130 $ | $ cat </dev/pts/29 $ el | hlo This is really frustrating as I need to do this in order to redirect the io of a process running in gdb (I've tried both run /dev/pts/# and set inferior-tty /dev/pts/# and both resulted in the aforementioned behavior). Am I doing something wrong, or is this a bug in bash/screen/dvtm?

    Read the article

  • Redirect one input from one terminal to another

    - by Niki Yoshiuchi
    I have sshed into a linux box and I'm using dvtm and bash (although I have also tried this with Gnu screen and bash). I have two terminals, current /dev/pts/29 and /dev/pts/130. I want to redirect the input from one to the other. From what I understand, in /dev/pts/130 I can type: cat </dev/pts/29 And then when I type in /dev/pts/29 the characters I type should show up in /dev/pts/130. However what ends up happening is that every other character I type gets redirected. For example, if I type "hello" I get this: /dev/pts/29 | /dev/pts/130 $ | $ cat </dev/pts/29 $ el | hlo This is really frustrating as I need to do this in order to redirect the io of a process running in gdb (I've tried both run /dev/pts/# and set inferior-tty /dev/pts/# and both resulted in the aforementioned behavior). Am I doing something wrong, or is this a bug in bash/screen/dvtm?

    Read the article

  • Disk space suddenly 100% used?

    - by dannymcc
    I'm trying to identify why, suddenly, 100% of our disk space is in use. I have already rebooted but the issue persists. Here are the outputs of some commands that are showing some strange (for me) results: danny@hydrogen:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/cciss/c0d0p1 130G 122G 949M 100% / none 1.9G 196K 1.9G 1% /dev none 2.0G 0 2.0G 0% /dev/shm none 2.0G 40K 2.0G 1% /var/run none 2.0G 0 2.0G 0% /var/lock none 2.0G 0 2.0G 0% /lib/init/rw danny@hydrogen:/$ sudo du -chs / du: cannot access `/proc/1662/task/1662/fd/4': No such file or directory du: cannot access `/proc/1662/task/1662/fdinfo/4': No such file or directory du: cannot access `/proc/1662/fd/4': No such file or directory du: cannot access `/proc/1662/fdinfo/4': No such file or directory danny@hydrogen:/$ df Filesystem 1K-blocks Used Available Use% Mounted on /dev/cciss/c0d0p1 135342296 128144108 323104 100% / none 1991336 196 1991140 1% /dev none 1995788 0 1995788 0% /dev/shm none 1995788 40 1995748 1% /var/run none 1995788 0 1995788 0% /var/lock none 1995788 0 1995788 0% /lib/init/rw danny@hydrogen:/$ mount /dev/cciss/c0d0p1 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) danny@hydrogen:/$ sudo du -h --max-depth=1 634M ./premvet_sync 5.6M ./etc 4.0K ./opt 16K ./lost+found 7.4M ./bin 623M ./lib 196K ./dev 0 ./sys 4.0K ./srv 4.0K ./cdrom 8.0K ./media 52K ./tmp ... it hangs for ages here..... The server is running Ubuntu 10.04.4 LTS. System load: 2.85 Temperature: 8 C Usage of /: 94.7% of 129.07GB Processes: 132 Memory usage: 39% Users logged in: 0 Swap usage: 0% IP address for eth0: 192.168.1.124 => / is using 94.7% of 129.07GB I'm struggling to comprehend why this is happening! Any pointers would be appreciated.

    Read the article

  • External USB Drive

    - by ErocM
    I have a server that I hooked up an external USB drive. It was formatted in windows and has files on it already. I'm new to Ubuntu so please be patient... I have two questions: Will Ubuntu see the drive since it was formatted in windows? How do I mount this drive or rather, how do I know it's seen by Ubuntu? Thanks! I did fdisk -l and this is what I have but I don't see it. It's a 1tb drive: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001eb47 Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM Disk /dev/sdc: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table Disk /dev/sdb: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdb doesn't contain a valid partition table Disk /dev/mapper/ubuntu-root: 316.6 GB, 316577677312 bytes 255 heads, 63 sectors/track, 38488 cylinders, total 618315776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/ubuntu-root doesn't contain a valid partition table Disk /dev/mapper/ubuntu-swap_1: 3217 MB, 3217031168 bytes 255 heads, 63 sectors/track, 391 cylinders, total 6283264 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 this is an external USB hard drive not a thumb drive :)

    Read the article

  • How to mount an external HDD?

    - by Slash
    I have Ubuntu Linux 12.04 version the latest right now.I want to mount an external HDD NTFS 1TB.I have followed many guides but still no success.The error I'm getting is this: Failed to read last sector (1953523119): Invalid argument HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS), or the NTFS boot sector is corrupt (NTFS size is not valid). Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? Using Storage Device MAnager i get this error:Error mounting: mount exited with exit code 1: helper failed with: mount: only root can mount /dev/sdb1 on /media/Skliros_Diskos {external disk name} When I use sudo fdisk -l, this is the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e0bc6 Device Boot Start End Blocks Id System /dev/sda1 * 2048 618854399 309426176 83 Linux /dev/sda2 618856446 625141759 3142657 5 Extended /dev/sda5 618856448 625141759 3142656 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002093a Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 7 HPFS/NTFS/exFAT

    Read the article

  • I can't install Ubuntu on my Dell Inspiron 15R at all

    - by Kieran Rimmer
    I'm attempting to install Ubuntu 12.04LTS, 64 bit onto a Dell Inspiron 15R laptop. I've shrunk down one of the windows partitions and even used gparted to format the vacant space as ext4. However, the install disk simply does not present any options when it comes to the partitioning step. What I get is a non-responsive blank table As well as the above, I've changed the BIOS settings so that USB emulation is disabled (as per Can't install on Dell Inspiron 15R), and changed the SATA Operation setting to all three possible options. Anyway, the install CD will bring up the trial version of ubuntu, and if I open terminal and type sudo fdisk -l, I get this: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xb4fd9215 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/sda2 * 81920 29044735 14481408 7 HPFS/NTFS/exFAT /dev/sda3 29044736 1005142015 488048640 7 HPFS/NTFS/exFAT /dev/sda4 1005154920 1953520064 474182572+ 83 Linux Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb4fd923d Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive If I type 'sudo parted -l', I get: Model: ATA WDC WD10JPVT-75A (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 41.1MB 41.1MB primary fat16 diag 2 41.9MB 14.9GB 14.8GB primary ntfs boot 3 14.9GB 515GB 500GB primary ntfs 4 515GB 1000GB 486GB primary ext4 Model: ATA SAMSUNG SSD PM83 (scsi) Disk /dev/sdb: 32.0GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 8589MB 8588MB primary Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: Can't have a partition outside the disk! I've also tried a Kubuntu 12.04 and Linuxmint install disks, wityh the same problem. I'm completely lost here. Cheers, Kieran

    Read the article

  • disk space worngly displayed after installing LVM disk

    - by Ubuntuser
    I installed ubuntu server using LVM partitioning on a 1 TB hard disk. However, after installation, i can only see 10 Gig space here is the fidsk output ` # fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00041507 Device Boot Start End Blocks Id System /dev/sda1 * 1 10 71680 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 10 121602 976689152 8e Linux LVM Disk /dev/dm-0: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 2147 MB, 2147483648 bytes 255 heads, 63 sectors/track, 261 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table You have new mail in /var/mail/root and df -h output df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system-root 9.9G 6.6G 2.8G 71% / devtmpfs 1.9G 232K 1.9G 1% /dev tmpfs 1.9G 4.0K 1.9G 1% /dev/shm /dev/sda1 68M 22M 43M 34% /boot tmpfs 6.0G 0 6.0G 0% /var/spool/asterisk/monitor You have new mail in /var/mail/root ` any way to increase this space without reisntalling?

    Read the article

  • Ubuntu installer does not show drives

    - by Tanweer Rashid
    I am trying to install Ubuntu 12.04 LTS on my Inspiron laptio, but the installer does not show any drives. My system has a 1TB SATA drive and a 32GB SSD. As far as I can figure, the boot files are kept on the SSD for fast startup (for Windows). During Win7 installation, I had to manually load drivers for RAID controller to see all available drives. Running fdisk -l from the live CD shows the following: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b4782 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 81920 41627647 20772864 7 HPFS/NTFS/exFAT /dev/sda3 41627648 357019647 157696000 7 HPFS/NTFS/exFAT /dev/sda4 357019648 1953517567 798248960 f W95 Ext'd (LBA) /dev/sda5 672415744 1312966655 320275456 7 HPFS/NTFS/exFAT /dev/sda6 1312968704 1953517567 320274432 7 HPFS/NTFS/exFAT Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b474b Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive ubuntu@ubuntu:~$ In the Ubuntu installer, I can only choose /dev/sdb for "Device for boot loader installation", and sdb doesn't show any drives. I cannot select /dev/sda. Any ideas anyone? Thanks.

    Read the article

  • Disk Space Full

    - by Loki
    Setting up Ubuntu 10.04 server, the / disk space shows full under df, however the du does not show any of the space used. This has several mounts to Gluster FS'. I have tried a forced FSCK and to no avail. ~# df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 141G 132G 0 100% / none 3.0G 224K 3.0G 1% /dev none 3.0G 0 3.0G 0% /dev/shm none 3.0G 76K 3.0G 1% /var/run none 3.0G 0 3.0G 0% /var/lock none 3.0G 0 3.0G 0% /lib/init/rw /dev/sdb1 9.0T 7.1T 1.9T 80% /brick1 /dev/sdb2 9.0T 7.9T 1.1T 88% /brick2 localhost:/sanvol09 385T 330T 56T 86% /mnt/sanvol09 <- Gluster FS uses local software to contact the DFS I've attempted a tune2fs and same issue arises # du -h --max-depth=1 --one-file-system / 4.0K /selinux 0 /proc 47M /boot 31M /mnt 8.0K /brick1 8.0K /brick2 391M /lib 4.0K /opt 7.4M /bin 0 /sys 379M /var 5.6M /etc 16K /lost+found 43M /root 4.0K /srv 5.7M /home 4.0K /media 7.0M /sbin 0 /dev 4.0K /tmp 4.0K /cdrom 631M /usr 1.6G / more info # df -ih Filesystem Inodes IUsed IFree IUse% Mounted on /dev/md0 9.0M 91K 8.9M 1% / none 746K 770 745K 1% /dev none 747K 1 747K 1% /dev/shm none 747K 32 747K 1% /var/run none 747K 1 747K 1% /var/lock none 747K 3 747K 1% /lib/init/rw /dev/sdb1 583M 1.8M 581M 1% /brick1 /dev/sdb2 583M 1.9M 581M 1% /brick2 localhost:/sanvol09 25G 76M 25G 1% /mnt/sanvol09 The final question: df show's 100% used, and its not, any other known fixes?

    Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >