Search Results

Search found 9286 results on 372 pages for 'transfer speed'.

Page 258/372 | < Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Moving a lot of small files between servers using rsync

  - by Adirael

  Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

  Read the article

• Mac OS X will only upload zero-byte files through FTP

  - by tabacitu

  I'm using Mac OS X Lion and i've been having this problem with FTP (any FTP client, mind you. I tried Transmit, FileZilla, Cyberduck and the Terminal, all with the same result) I can browse files in my FTP Client, but when I upload files, the client hangs for a few seconds, then thinks it uploaded the files successfully, but it only creates a new file with one blank line in it. Sometimes, it manages to upload 4-5 lines. It then returns: 226 - Error during read from data connection 226 Transfer aborted But 2xx is a success message. It is not a server issue, since any Windows machine will upload just fine using the same network. Can anybody figure out what the problem is? It renders my mac useless for web development. The problem persists with SFTP and FTP with SSL/TLS. Later edit: Solved! Ok, turns out the problem goes away when I take out my router and connect directly through PPPoE. So the problem is with the router, I thought. But no, the problem is with the mac that connects through a router that connects through a PPPoE and tries to upload using FTP. Pretty specific, I know. The problem is with the MTU (maximum transmission unit). Apparently, mac os x breaks the file into chunks that are too large for the router to send, because the router's MTU was set lower than Mac OS X's. My router's was 1492, which is ok, but my Mac's MTU was 1500, which is unacceptable. I don't even understand why it works directly with PPPoE. Anyway, if you encounter the same problem, this is how you diagnose and fix it: In terminal, run: ifconfig | grep mtu to see what the MTU is for en0 (or en1, mine was en0) If it's 1500, run sudo ifconfig en0 mtu 1300 This should solve it. If so, it may only be until the next restart. You can also change the MTU in System Preferences \ Network \ Ethernet - Advanced \ Hardware

  Read the article

• Servers/Websites Keep Going Down

  - by Tyler Johnson

  Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

  Read the article

• Force delivery retry without restarting the SMTP Service on Windows Server 2008 R2

  - by Mathias R. Jessen

  I have a Windows Server 2008 R2 box hosting 3 virtual SMTP servers; vSMTP01, vSMTP02 and vSMTP03. The first two are configured to deliver all messages to dedicated smarthosts, while the last is set to just deliver the messages on its own. All other delivery settings are as default ----(vSMTP01)-----> {SMARTHST01} / ----Inbound mail--->---SMTPSRV01---[----(vSMTP02)-----> {SMARTHST02} \ ----(vSMTP03)-----> { Internet } Now I want to take SMARTHST01 out for maintenance, but I don't want to reject submissions to vSMTP01 while doing so, so I just let it continue running. When SMARTHST01 is no longer responding, vSMTP01 queues the messages and wait for the first retry interval to pass (15 minutes). So far so good. Let's say SMARTHST01 gets online again after 20 minutes. The first interval has passed, and I'll have to wait another 25 minutes for the second retry interval to pass. If I stop and start the SMTP Service (Services.msc - Simple Mail Transfer Protocol service - Stop), the server will retry all deliveries, but that would cause a service interruption for ALL virtual SMTP servers on the machine, which is highly undesirable. How can I manually force vSMTP01 to retry delivery of all queued messages without interrupting the service of vSMTP02 and vSMTP03?

  Read the article

• Apache, logerror and logrotate: what is the best method?

  - by OlivierDofus

  Hi! Here's a vhost example of my sites: <VirtualHost *:80> DocumentRoot /datas/web/woog ServerName woog.com ServerAlias www.woog.com ErrorLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/error_log 86400" CustomLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/access_log 86400" combined DirectoryIndex index.php index.htm <Location /> Allow from All </Location> <Directory /*> Options FollowSymLinks AllowOverride Limit AuthConfig </Directory> </VirtualHost> I've got 12 sites running now. This gives something like: [Shake]:/sources/software/mod_log_rotate# ps x | grep rotate /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 [snap (as many error_log as virtual hosts)] /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 [snap (as many access_log as virtual hosts)] grep rotate [Shake]:/sources/software/mod_log_rotate# !!! I've been looking everywhere but I've only found mod_log_rotate. The "little" problem is that the author (very good C developper) explains: "Unfortunately Apache error logs are handled in such a way that we can't work the same log rotation magic on them. Like transfer logs they support piped logging though so you can still use rotatelogs for them. " So my question is: what would be the best way to handle multiple logs? If I just do a very classical log and I use the system's "logrotate" program couldn't this be a good deal? How would/do you deal with that? Thank you!

  Read the article

• How to install wordpress without a web browser

  - by bvandrunen

  What I am trying to do is to automate wordpress website creation for the company I am working on. We have lots of information in our database for our customers and we want to create a wordpress website for each customer. The process works great and we have no trouble with the creation of websites/transfer of data or anything like that. The problem we do have is when we buy a new domain (http://www.newdomain.com) our process breaks (we call a stored procedure which installs all the data after the URL is called to install wordpress) if the domain takes more than 15min to resolve. We have tried doing looping (where the process checks to see if the domain resolves and keeps trying - but eventually if fails). So what we are looking for is to see if there is a way to install an URL without actually having the domain resolve yet. I have seen where possibilities where you can change the wp-config file but this doesn't work since we have more than one domain and it changes the source URL for all the domains. What we really need is just a way for us to manually start the install script through a call either through a database or some other way that doesn't check to see if the domain is resolved or pointing at the server or not. Thank for any suggestions. EDIT: All we do to install wordpress is call this URL: http://"newdomain".com/wp-admin/install.php?step=2 - if you change settings in the backend calling this URL will install wordpress without having to go through the wp-admin/install.php form

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Nginx server 301 Moved permanently

  - by user145714

  When I did a curl -v http://site-wordpress.com:81 I received this result: About to connect() to site-wordpress.com port 81 (#0) Trying ip... connected Connected to site-wordpress.com (ip) port 81 (#0) GET / HTTP/1.1 User-Agent: curl/7.19.7 (x86_64-unknown-linux-gnu) libcurl/7.19.7 NSS/3.12.6.2 zlib/1.2.3 libidn/1.18 libssh2/1.2.2 Host: site-wordpress.com:81 Accept: / < HTTP/1.1 301 Moved Permanently < Server: nginx/1.2.4 < Date: Fri, 16 Nov 2012 16:28:19 GMT < Content-Type: text/html; charset=UTF-8 < Transfer-Encoding: chunked < Connection: keep-alive < X-Pingback: The URL above/xmlrpc.php < Location: The URL above Seems like this line in my fastcgi_params is causing grief. fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; If I remove this line , I get HTTP/1.1 200 OK but I get a blank page. This is my config: server { listen 81; server_name site-wordpress.com; root /var/www/html/site; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; index index.php; if (!-e $request_filename){ rewrite ^(.*)$ /index.php break; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; # port where FastCGI processes were spawned fastcgi_index index.php; include /etc/nginx/fastcgi_params; include /etc/nginx/mime.types; } location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; } } This config works with ip and port 80. But now I need to use a domain name and port 81, which doesn't work. Could someone please help. Thanks.

  Read the article

• How to Set Up an SMTP Submission Server on Linux

  - by Kevin Cox

  I was trying to set up a mail server with no luck. I want it to accept mail from authenticated users only and deliver them. I want the users to be able to connect over the internet. Ideally the mail server wouldn't accept any incoming mail. Essentially I want it to accept messages on a receiving port and transfer them to the intended recipient out port 25. If anyone has some good links and guides that would be awesome. I am quite familiar with linux but have never played around with MTA's and am currently running debian 6. More Specific Problem! Sorry, that was general and postfix is complex. I am having trouble enabling the submission port with encryption and authentication. What Works: Sending mail from the local machine. (sendmail [email protected]). Ports are open. (25 and 587) Connecting to 587 appears to work, I get a "need to starttls" warning and starttls appears to work. But when I try to connect with the next command I get the error below. # openssl s_client -connect localhost:587 -starttls smtp CONNECTED(00000003) depth=0 /CN=localhost.localdomain verify error:num=18:self signed certificate verify return:1 depth=0 /CN=localhost.localdomain verify return:1 --- Certificate chain 0 s:/CN=localhost.localdomain i:/CN=localhost.localdomain --- Server certificate -----BEGIN CERTIFICATE----- MIICvDCCAaQCCQCYHnCzLRUoMTANBgkqhkiG9w0BAQUFADAgMR4wHAYDVQQDExVs b2NhbGhvc3QubG9jYWxkb21haW4wHhcNMTIwMjE3MTMxOTA1WhcNMjIwMjE0MTMx OTA1WjAgMR4wHAYDVQQDExVsb2NhbGhvc3QubG9jYWxkb21haW4wggEiMA0GCSqG SIb3DQEBAQUAA4IBDwAwggEKAoIBAQDEFA/S6VhJihP6OGYrhEtL+SchWxPZGbgb VkgNJ6xK2dhR7hZXKcDtNddL3uf1YYWF76efS5oJPPjLb33NbHBb9imuD8PoynXN isz1oQEbzPE/07VC4srbsNIN92lldbRruDfjDrAbC/H+FBSUA2ImHvzc3xhIjdsb AbHasG1XBm8SkYULVedaD7I7YbnloCx0sTQgCM0Vjx29TXxPrpkcl6usjcQfZHqY ozg8X48Xm7F9CDip35Q+WwfZ6AcEkq9rJUOoZWrLWVcKusuYPCtUb6MdsZEH13IQ rA0+x8fUI3S0fW5xWWG0b4c5IxuM+eXz05DvB7mLyd+2+RwDAx2LAgMBAAEwDQYJ KoZIhvcNAQEFBQADggEBAAj1ib4lX28FhYdWv/RsHoGGFqf933SDipffBPM6Wlr0 jUn7wler7ilP65WVlTxDW+8PhdBmOrLUr0DO470AAS5uUOjdsPgGO+7VE/4/BN+/ naXVDzIcwyaiLbODIdG2s363V7gzibIuKUqOJ7oRLkwtxubt4D0CQN/7GNFY8cL2 in6FrYGDMNY+ve1tqPkukqQnes3DCeEo0+2KMGuwaJRQK3Es9WHotyrjrecPY170 dhDiLz4XaHU7xZwArAhMq/fay87liHvXR860tWq30oSb5DHQf4EloCQK4eJZQtFT B3xUDu7eFuCeXxjm4294YIPoWl5pbrP9vzLYAH+8ufE= -----END CERTIFICATE----- subject=/CN=localhost.localdomain issuer=/CN=localhost.localdomain --- No client certificate CA names sent --- SSL handshake has read 1605 bytes and written 354 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: E07926641A5EF22B15EB1D0E03FFF75588AB6464702CF4DC2166FFDAC1CA73E2 Session-ID-ctx: Master-Key: 454E8D5D40380DB3A73336775D6911B3DA289E4A1C9587DDC168EC09C2C3457CB30321E44CAD6AE65A66BAE9F33959A9 Key-Arg : None Start Time: 1349059796 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN read:errno=0 If I try to connect from evolution I get the following error: The reported error was "HELO command failed: TCP connection reset by peer".

  Read the article

• Windows 7 - SBS - Why does copying a directory not include all subdirectories and files?

  - by indeed005

  Using Windows 7, fully updated... I have had some strange behaviour copying a whole user directory (e.g. "c:\users\bob" to "c:\backups\bob") I understand now that I should have used Easy Transfer or at least robocopy, but at the time all I wanted to do was backup the user's data before using the "Delete account" button. Unfortunately, I didn't check that my copy-paste had actually worked; all it had actually done was copied the appdata subdirectory of the user account. At the time of doing this backup I was logged in as the same user, bob (a local admin) in this example. When I discovered the missing files, I tried again using the domain admin account -- same story. Only appdata copied. No documents folders, nothing else. Then my boss tried, and it worked fine -- it copied all the files. Ctrl+C, Ctrl+V. I tried again... same profile... copied all the files. Same profile, same destination, same rights and permissions, same ownership, but different behaviour. Has anyone encountered this before and come up with a solution? BTW this was not using roaming profiles and the accounts are stored locally.

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Shoretel Upgrade Path

  - by Brian

  I currently have a Shoretel Server running Server 2003 x32 as a virtual machine paired with a ShoreGear 90 switch and another unused switch of the same model being reserved for manual failover. I am getting the software mailed to me from my partner, but with limited support since the server is in a relatively remote area. I am tempted to upgrade the OS at the same time as performing the upgrade, but want to know if there are any horror stories or advice I should know about before diving in. I'm upgrading from Shoretel 9.2 Build. I will be upgrading first to version 10.1 then finally to 11.1. The system has been bullet proof since it was installed and we are upgrading mainly to get a client that is a little more modern. My question boils down to: Should I even bother with an OS upgrade or even possibly a fresh install of Windows with an install of Shoretel 11.1 and just transfer the configuration? Should I just stay with Server 2003 since it is supported in my target version of Shoretel and the upgrade will be more than enough to keep me busy as a novice?

  Read the article

• backup an existing linux server to a virtualbox virtual machine

  - by user146526

  I have some servers and VPSs to many companies across the world. I want to back them up locally. I have some backup solutions enabled to remote hosts, but I want to have a local backup on a computer at home. What I am thinking is: 1) Create a virtualbox virtual machine, install the same version linux as the server. 2) Use rsync to backup the server to the local virtualbox machine. (something like rsync -av --delete --progress --exclude '/dev/' --exclude '/proc/' root@server_ip:// / ) 3) Repeat the command every few days update files. 4) In case of a hard disk failure, or any other bad event, reverse the rsync command and get the files back and continue my bussiness. I tried it with 2 openvz VPS, the one was a backup of the other. I also tried to transfer normal linux server host to openvz machine and it worked great. That way looks pretty clean and easy to me, this is the kind of solution I am looking for. However I need to be sure that this will work if I am going to do it. The question is, will that work ok ? Does anyone see any problem with that ? Do you have any other suggestions ? Thanks

  Read the article

• Apache, logerror and logrotate: what is the best method?

  - by OlivierDofus

  Here's a vhost example of my sites: <VirtualHost *:80> DocumentRoot /datas/web/woog ServerName woog.com ServerAlias www.woog.com ErrorLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/error_log 86400" CustomLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/access_log 86400" combined DirectoryIndex index.php index.htm <Location /> Allow from All </Location> <Directory /*> Options FollowSymLinks AllowOverride Limit AuthConfig </Directory> </VirtualHost> I've got 12 sites running now. This gives something like: [Shake]:/sources/software/mod_log_rotate# ps x | grep rotate /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 [snap (as many error_log as virtual hosts)] /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 [snap (as many access_log as virtual hosts)] grep rotate [Shake]:/sources/software/mod_log_rotate# !!! I've been looking everywhere but I've only found mod_log_rotate. The "little" problem is that the author (very good C developper) explains: "Unfortunately Apache error logs are handled in such a way that we can't work the same log rotation magic on them. Like transfer logs they support piped logging though so you can still use rotatelogs for them. " So my question is: what would be the best way to handle multiple logs? If I just do a very classical log and I use the system's "logrotate" program couldn't this be a good deal? How would/do you deal with that? Thank you!

  Read the article

• Loadbalancing with nginx and tomcat

  - by London

  Hello this should be fairly easy to answer for any system admin, the problem is that I'm not server admin but I have to complete this task, I'm very close but still not managing to do it. Here is what I mean, I have two tomcat instance running on machine1 and machine2. People usually access those by visiting urls : http://machine1:8080/appName http://machine2:9090/appName The problem is when I setup nginx with domain name i.e domain.com, nginx sends requests to http://machine1:8080/ and http://machine2:9090/ instead of http://machine1:8080/ and http://machine2:9090/appName Here is my configuration (very basic as it can be noted) : upstream backend { server machine1:8080; server machine2:9090; } server { listen 80; server_name www.mydomain.com mydomain.com; location / { # needed to forward user's IP address to rails proxy_set_header X-Real-IP $remote_addr; # needed for HTTPS proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://backend; } #end location } #end server What changes must I do to do the following : - when user visits mydomain.com - transfer him to either machine1:8080/appName or machine2:9090 Thank you

  Read the article

• Mysqld shutting down by itself

  - by AJ Naidas

  I'm running a Wordpress Blog that gets medium-high traffic. It is hosted in an Ubuntu Server 2GB Memory 2 Core Processor 40GB SSD Disk, 3TB Transfer. The problem is that MySQL shuts down by itself after an hour or two. I had to restart mysql each and every time this happens. I checked the logs and this is what I found: 140612 6:48:14 [Warning] Using unique option prefix myisam-recover instead of myisam-recover-options is deprecated and will be removed in a future release. Please use the full name instead. 140612 6:48:14 [Note] Plugin 'FEDERATED' is disabled. 140612 6:48:14 InnoDB: The InnoDB memory heap is disabled 140612 6:48:14 InnoDB: Mutexes and rw_locks use GCC atomic builtins 140612 6:48:14 InnoDB: Compressed tables use zlib 1.2.3.4 140612 6:48:14 InnoDB: Initializing buffer pool, size = 1.4G InnoDB: mmap(1502412800 bytes) failed; errno 12 140612 6:48:14 InnoDB: Completed initialization of buffer pool 140612 6:48:14 InnoDB: Fatal error: cannot allocate memory for the buffer pool 140612 6:48:14 [ERROR] Plugin 'InnoDB' init function returned error. 140612 6:48:14 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 140612 6:48:14 [ERROR] Unknown/unsupported storage engine: InnoDB 140612 6:48:14 [ERROR] Aborting 140612 6:48:14 [Note] /usr/sbin/mysqld: Shutdown complete judging by this line: 140612 6:48:14 InnoDB: Fatal error: cannot allocate memory for the buffer pool I suspect that this is a memory problem, but I would like to hear from the experts here before I conclude. Is this a lack of memory problem? Do you think the value of max_connections in my.cnf (currently 100) is a potential cause and needs increasing? TIA.

  Read the article

• Does having TRIM enabled affect other hard drives on a computer (and how do you know when Windows is using it)?

  - by Breakthrough

  I recently purchased a solid state drive (an OCZ Vertex 2 (80 GB)) to use as my primary operating system partition. I also have three other SATA hard drives of assorted sizes. I successfully installed Windows 7 Professional onto the SSD (works awesome, great response time and transfer rate), and used the other three HDDs for data storage. I was browsing through the Bible of OCZ SSDs, and noticed the following in Section 60-76 - Tweaks and TRIM: Q. How do I know if TRIM is enabled on my OCZ SSD? A. In Windows 7, go to start/run/cmd), type the following: fsutil.exe behaviour query DisableDeleteNotify It should respond back with: DisableDeleteNotify=0 if TRIM support is ready and active. If it's not, then type: fsutil.exe behavior set DisableDeleteNotify 0 After a bit of searching on Google, I found similar results elsewhere (set DisableDeleteNotify to 0, which makes sense since for TRIM to work, the solid-state drive needs to be notified when deletes occur (for the garbage collector) unlike a normal hard drive). When I run the query on fsutil, I get the following result: DisableDeleteNotify = 48 Following the instructions I found, I set this to 0 instead of 48. However, I am beginning to wonder. Is this all the proof I really need that the OS is using TRIM? Also, since this applies globally for the computer, is TRIM data being sent to the other hard drives connected to the computer? And if so, would this cause any degradation in disk performance?

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Apache https is slow

  - by raucous12

  Hey, I've set apache up to use SSL with a self signed certificate. With https (KeepAlive on), I can get over 3000 requests per second. However, with https (KeepAlive off), I can only get 13 requests per second. I know there is supposed to be a bit of an overhead, but this seems abnormal. Can anyone suggest how I might go about debugging this. Here is the ab log for https: Server Software: Apache/2.2.3 Server Hostname: 127.0.0.1 Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,DHE-RSA-AES256-SHA,4096,256 Document Path: /hello.html Document Length: 29 bytes Concurrency Level: 5 Time taken for tests: 30.49425 seconds Complete requests: 411 Failed requests: 0 Write errors: 0 Total transferred: 119601 bytes HTML transferred: 11919 bytes Requests per second: 13.68 [#/sec] (mean) Time per request: 365.565 [ms] (mean) Time per request: 73.113 [ms] (mean, across all concurrent requests) Transfer rate: 3.86 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 190 347 74.3 333 716 Processing: 0 14 24.0 1 166 Waiting: 0 11 21.6 0 165 Total: 191 361 80.8 345 716 Percentage of the requests served within a certain time (ms) 50% 345 66% 377 75% 408 80% 421 90% 468 95% 521 98% 578 99% 596 100% 716 (longest request)

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

• What does the 'Burst Rate' stat mean in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• Server Hosting + AWS

  - by ledy

  Since my dedicated servers are hosted at a "normal" hosting service, I wonder if there is a really cheap way to extend the server farm with AWS instances. E.g. it seems to be a effient and flexible solution with data storage and ressources for ocassional data processing, too. However, it might be very in-efficient to mix two data centres and transfering data from current webhoster to amazon and vice-versa. In my case, the traffic for this continuous data exchange seems to be expensive and the delay for moving the data back to the hoster leads into a lack or delay. How are best practises for mixing non-aws and aws systems? E.g.: How to move the hosters data to aws as log file storage to run urchin analysis and/or port the log file data into a bigtable for exhausting analysis there. After working with the data: how to bring it back to the hoster and use the data with the webservers there? I am not going to move all the server farm to amazon, only "separate" parts or tasks if the transfer/exchange does not lead to increased cost.

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

< Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >