Search Results

Search found 2050 results on 82 pages for 'c 03'.

Page 26/82 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

• Unable to list contents/remove directory (linux ext3)

  - by RedKrieg

  System is CentOS5 x86_64, completely up to date. I've got a folder that can't be listed (ls just hangs, eating memory until it is killed). The directory size is nearly 500k: root@server [/home/user/public_html/domain.com/wp-content/uploads/2010/03]# stat . File: `.' Size: 458752 Blocks: 904 IO Block: 4096 directory Device: 812h/2066d Inode: 44499071 Links: 2 Access: (0755/drwxr-xr-x) Uid: ( 3292/ user) Gid: ( 3287/ user) Access: 2012-06-29 17:31:47.000000000 -0400 Modify: 2012-10-23 14:41:58.000000000 -0400 Change: 2012-10-23 14:41:58.000000000 -0400 I can see the file names if I use ls -1f, but it just repeats the same 48 files ad infinitum, all of which have non-ascii characters somewhere in the file name: La-critic\363-al-servicio-la-privacidad-300x160.jpg When I try to access the files (say to copy them or remove them) I get messages like the following: lstat("/home/user/public_html/domain.com/wp-content/uploads/2010/03/Sebast\355an-Pi\361era-el-balc\363n-150x120.jpg", 0x7fff364c52c0) = -1 ENOENT (No such file or directory) I tried altering the code found on this man page and modified the code to call unlink for each file. I get the same ENOENT error from the unlink call: unlink("/home/user/public_html/domain.com/wp-content/uploads/2010/03/Marca-naci\363n-Madrid-150x120.jpg") = -1 ENOENT (No such file or directory) I also straced a "touch", grabbed the syscalls it makes and replicated them, then tried to unlink the resulting file by name. This works fine, but the folder still contains an entry by the same name after the operation completes and the program runs for an arbitrarily long time (strace output ended up at 20GB after 5 minutes and I stopped the process). I'm stumped on this one, I'd really prefer not to have to take this production machine (hundreds of customers) offline to fsck the filesystem, but I'm leaning toward that being the only option at this point. If anyone's had success using other methods for removing files (by inode number, I can get those with the getdents code) I'd love to hear them. (Yes, I've tried find . -inum <inode> -exec rm -fv {} \; and it still has the problem with unlink returning ENOENT) For those interested, here's the diff between that man page's code and mine. I didn't bother with error checking on mallocs, etc because I'm lazy and this is a one-off: root@server [~]# diff -u listdir-orig.c listdir.c --- listdir-orig.c 2012-10-23 15:10:02.000000000 -0400 +++ listdir.c 2012-10-23 14:59:47.000000000 -0400 @@ -6,6 +6,7 @@ #include <stdlib.h> #include <sys/stat.h> #include <sys/syscall.h> +#include <string.h> #define handle_error(msg) \ do { perror(msg); exit(EXIT_FAILURE); } while (0) @@ -17,7 +18,7 @@ char d_name[]; }; -#define BUF_SIZE 1024 +#define BUF_SIZE 1024*1024*5 int main(int argc, char *argv[]) { @@ -26,11 +27,16 @@ struct linux_dirent *d; int bpos; char d_type; + int deleted; + int file_descriptor; fd = open(argc > 1 ? argv[1] : ".", O_RDONLY | O_DIRECTORY); if (fd == -1) handle_error("open"); + char* full_path; + char* fd_path; + for ( ; ; ) { nread = syscall(SYS_getdents, fd, buf, BUF_SIZE); if (nread == -1) @@ -55,7 +61,24 @@ printf("%4d %10lld %s\n", d->d_reclen, (long long) d->d_off, (char *) d->d_name); bpos += d->d_reclen; + if ( d_type == DT_REG ) + { + full_path = malloc(strlen((char *) d->d_name) + strlen(argv[1]) + 2); //One for the /, one for the \0 + strcpy(full_path, argv[1]); + strcat(full_path, (char *) d->d_name); + + //We're going to try to "touch" the file. + //file_descriptor = open(full_path, O_WRONLY|O_CREAT|O_NOCTTY|O_NONBLOCK, 0666); + //fd_path = malloc(32); //Lazy, only really needs 16 + //sprintf(fd_path, "/proc/self/fd/%d", file_descriptor); + //utimes(fd_path, NULL); + //close(file_descriptor); + deleted = unlink(full_path); + if ( deleted == -1 ) printf("Error unlinking file\n"); + break; //Break on first try + } } + break; //Break on first try } exit(EXIT_SUCCESS);

  Read the article

• How to get the child elementsvalue , when the parent element contains different number of child Elem

  - by Subhen

  Hi, I have the following XML Structure: <DIDL-Lite xmlns="urn:schemas-upnp-org:metadata-1-0/DIDL-Lite/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:upnp="urn:schemas-upnp-org:metadata-1-0/upnp/" xmlns:dlna="urn:schemas-dlna-org:metadata-1-0/"> <item id="1268" parentID="20" restricted="1"> <upnp:class>object.item.audioItem.musicTrack</upnp:class> <dc:title>Hey</dc:title> <dc:date>2010-03-17T12:12:26</dc:date> <upnp:albumArtURI dlna:profileID="PNG_TN" xmlns:dlna="urn:schemas-dlna-org:metadata-1-0">URL/albumart/22.png</upnp:albumArtURI> <upnp:icon>URL/albumart/22.png</upnp:icon> <dc:creator>land</dc:creator> <upnp:artist>sland</upnp:artist> <upnp:album>Change</upnp:album> <upnp:genre>Rock</upnp:genre> <res protocolInfo="http-get:*:audio/mpeg:DLNA.ORG_PN=MP3;DLNA.ORG_OP=01;DLNA.ORG_CI=0;DLNA.ORG_FLAGS=01700000000000000000000000000000" size="9527987" duration="0:03:58">URL/1268.mp3</res> <res protocolInfo="http-get:*:image/png:DLNA.ORG_PN=PNG_TN;DLNA.ORG_CI=01;DLNA.ORG_FLAGS=00f00000000000000000000000000000" colorDepth="24" resolution="160x160">URL/albumart/22.png</res> </item> <item id="1269" parentID="20" restricted="1"> <upnp:class>object.item.audioItem.musicTrack</upnp:class> <dc:title>Indian </dc:title> <dc:date>2010-03-17T12:06:32</dc:date> <upnp:albumArtURI dlna:profileID="PNG_TN" xmlns:dlna="urn:schemas-dlna-org:metadata-1-0">URL/albumart/13.png</upnp:albumArtURI> <upnp:icon>URL/albumart/13.png</upnp:icon> <dc:creator>MC</dc:creator> <upnp:artist>MC</upnp:artist> <upnp:album>manimal</upnp:album> <upnp:genre>Rap</upnp:genre> <res protocolInfo="http-get:*:audio/mpeg:DLNA.ORG_PN=MP3;DLNA.ORG_OP=01;DLNA.ORG_CI=0;DLNA.ORG_FLAGS=01700000000000000000000000000000" size="8166707" duration="0:03:24">URL/1269.mp3</res> <res protocolInfo="http-get:*:image/png:DLNA.ORG_PN=PNG_TN;DLNA.ORG_CI=01;DLNA.ORG_FLAGS=00f00000000000000000000000000000" colorDepth="24" resolution="160x160">URL/albumart/13.png</res> </item> <item id="1277" parentID="20" restricted="1"> <upnp:class>object.item.videoItem.movie</upnp:class> <dc:title>IronMan_TeaserTrailer-full_NEW.mpg</dc:title> <dc:date>2010-03-17T12:50:24</dc:date> <upnp:genre>Unknown</upnp:genre> <res protocolInfo="http-get:*:video/mpeg:DLNA.ORG_PN=(NULL);DLNA.ORG_OP=01;DLNA.ORG_CI=0;DLNA.ORG_FLAGS=01700000000000000000000000000000" size="98926592" resolution="1920x1080" duration="0:02:30">URL/1277.mpg</res> </item> </DIDL-Lite> Here in the last Elemnt Item , there are few missing elements like icon,albumArtURi ..etc. Now whhile Ity to access the Values by following LINQ to XML query, var vAudioData = from xAudioinfo in xResponse.Descendants(ns + "DIDL-Lite").Elements(ns + "item").Where(x=>!x.Elements(upnp+"album").l orderby ((string)xAudioinfo.Element(upnp + "artist")).Trim() select new RMSMedia { strAudioTitle = ((string)xAudioinfo.Element(dc + "title")).Trim(),//((string)xAudioinfo.Attribute("audioAlbumcoverImage")).Trim()=="" ? ((string)xAudioinfo.Element("Song")).Trim():"" }; It show object reference is not set to reference of object. I do undersrand this is because of missing elements, is there any way I can pre-check if the elements exist , or check the number of elemnts inside item or any other way. Any help is deeply appreciated. Thanks, Subhen

  Read the article

• Trac FastCGI + Python on dreamhost leaves zombie python running

  - by Katsuke

  Hello there, Recently I installed trac in one of my dreamhost domains. I followed the instructions of http://trac.mlalonde.net/wiki/CreamyTrac and everything worked perfectly. At least i thought that was the case. After a few days, i started to notice that i was getting random 500 pages. I quickly checked the error log, and found a bunch of: [Fri Apr 16 14:35:34 2010] [error] [client *.*.*.*] Premature end of script headers: dispatch.fcgi [Fri Apr 16 14:35:54 2010] [error] [client *.*.*.*] Premature end of script headers: dispatch.fcgi, referer: http://www.trac.****.com/login [Fri Apr 16 16:05:58 2010] [error] [client *.*.*.*] Premature end of script headers: dispatch.fcgi, referer: http://www.trac.****.com/timeline The trac instance has very low traffic so it is possible that this might have been triggered faster if there was more use of it. So next step i went to look at top and am amazed by what i see: (this is NOT exactly what i saw, i just reproduced this from memory) 23730 rl_inst 20 0 44516 15m 4012 S 0.0 0.4 0:00.17 python2.4 23731 rl_inst 20 0 44616 15m 4012 S 0.0 0.4 0:03.17 python2.4 23732 rl_inst 20 0 44116 15m 4012 S 0.0 0.4 0:01.17 python2.4 23733 rl_inst 20 0 44826 15m 4012 S 0.0 0.4 0:04.17 python2.4 23734 rl_inst 20 0 44216 15m 4012 S 0.0 0.4 0:02.17 python2.4 23735 rl_inst 20 0 44416 15m 4012 S 0.0 0.4 0:01.17 python2.4 I opened the trac site again and that changed to this: 23730 rl_inst 20 0 44516 15m 4012 S 0.0 0.4 0:00.17 python2.4 23731 rl_inst 20 0 44616 15m 4012 S 0.0 0.4 0:03.17 python2.4 23732 rl_inst 20 0 44116 15m 4012 S 0.0 0.4 0:01.17 python2.4 23733 rl_inst 20 0 44826 15m 4012 S 0.0 0.4 0:04.17 python2.4 23734 rl_inst 20 0 44216 15m 4012 S 0.0 0.4 0:02.17 python2.4 23735 rl_inst 20 0 44416 15m 4012 S 0.0 0.4 0:01.17 python2.4 28378 rl_inst 20 0 2608 1208 1008 S 0.0 0.0 0:00.00 dispatch.fcgi 28382 rl_inst 20 0 44248 15m 4012 S 0.0 0.4 0:02.19 python2.4 So the dispatch.fcgi was being called correctly and was spawning correctly other python2.4 process. After the IDLE time passed this is the results: 23730 rl_inst 20 0 44516 15m 4012 S 0.0 0.4 0:00.17 python2.4 23731 rl_inst 20 0 44616 15m 4012 S 0.0 0.4 0:03.17 python2.4 23732 rl_inst 20 0 44116 15m 4012 S 0.0 0.4 0:01.17 python2.4 23733 rl_inst 20 0 44826 15m 4012 S 0.0 0.4 0:04.17 python2.4 23734 rl_inst 20 0 44216 15m 4012 S 0.0 0.4 0:02.17 python2.4 23735 rl_inst 20 0 44416 15m 4012 S 0.0 0.4 0:01.17 python2.4 28382 rl_inst 20 0 44248 15m 4012 S 0.0 0.4 0:02.19 python2.4 dispatch.fcgi was gone but the corresponding python2.4 was still there o_O. I had started with 5 sleeping processes of python and after idle time i ended up with 6. I repeated this and found that it kept spawning more and more python2.4, this was indeed what was causing my 500s indirectly. Let me explain my findings. Am on a shared hosting so my processes get killed if they are way too many. So everytime i opened trac 2 new processes spawned and one remained, to the point that dreamhost was killing a random process when i reached my limit. Sometimes killing the python2.4 that actually was rendering the current page. Hence header premature ending, python is gone the .fcgi doesnt know what to do and throws an 500. I found a dirty solution to this. I changed my dispatch.fcgi to contain a line that killed any currently running python2.4 process and then spawn a new one. Since then i dont get any rogues what so ever. But i dont think this is the best solution, calling killall in every fcgi just seems wrong. Anyone has run into this issue and found a cleaner solution? Is there anything that i have overlooked?

  Read the article

• g++ symbol versioning. Set it to GCC_3.0 using version 4 of g++

  - by Ismael

  Hi all I need to implemente a Java class which uses JNI to control a fiscal printer in XUbuntu 8.10 with sun-java6-jdk installed. The structure is the following: EpsonDriver.java loads libEpson.so libEpson is linked dynamically with EpsonFiscalProtocol.so ( provided by Epson, no source available ) and pthread I use javah to generate the header file, and the code compiles. Then I put the libEpson.so in $JAVA_HOME/jre/lib/i386, and EpsonDriver.java uses an static initializar System.loadLibrary("libEpson") That part works, however, when I try to use any of the methods I get an unsatisfiedLinkError exception. Some time ago, a coworker did a version that works, and using objdump -Dslx I got the following: Program Header: LOAD off 0x00000000 vaddr 0x00000000 paddr 0x00000000 align 2**12 filesz 0x0000ccc4 memsz 0x0000ccc4 flags r-x LOAD off 0x0000d000 vaddr 0x0000d000 paddr 0x0000d000 align 2**12 filesz 0x00000250 memsz 0x00044a5c flags rw- DYNAMIC off 0x0000d014 vaddr 0x0000d014 paddr 0x0000d014 align 2**2 filesz 0x000000f0 memsz 0x000000f0 flags rw- NOTE off 0x000000d4 vaddr 0x000000d4 paddr 0x000000d4 align 2**2 filesz 0x00000024 memsz 0x00000024 flags r-- STACK off 0x00000000 vaddr 0x00000000 paddr 0x00000000 align 2**2 filesz 0x00000000 memsz 0x00000000 flags rw- Dynamic Section: NEEDED EpsonFiscalProtocol.so NEEDED libpthread.so.0 NEEDED libstdc++.so.6 NEEDED libm.so.6 NEEDED libc.so.6 SONAME libcom_tichile_jpos_EpsonSerialDriver.so INIT 0x00007254 FINI 0x0000ba08 GNU_HASH 0x000000f8 STRTAB 0x00001f50 SYMTAB 0x00000ae0 STRSZ 0x00002384 SYMENT 0x00000010 PLTGOT 0x0000d108 PLTRELSZ 0x00000008 PLTREL 0x00000011 JMPREL 0x0000724c REL 0x000045c4 RELSZ 0x00002c88 RELENT 0x00000008 TEXTREL 0x00000000 VERNEED 0x00004564 VERNEEDNUM 0x00000002 VERSYM 0x000042d4 RELCOUNT 0x000000ac Version References: required from libstdc++.so.6: 0x056bafd3 0x00 05 CXXABI_1.3 0x08922974 0x00 04 GLIBCXX_3.4 required from libc.so.6: 0x0b792650 0x00 03 GCC_3.0 0x0d696910 0x00 02 GLIBC_2.0 In the recently compiled file I get: Program Header: LOAD off 0x00000000 vaddr 0x00000000 paddr 0x00000000 align 2**12 filesz 0x00005300 memsz 0x00005300 flags r-x LOAD off 0x00005300 vaddr 0x00006300 paddr 0x00006300 align 2**12 filesz 0x00000274 memsz 0x00010314 flags rw- DYNAMIC off 0x00005314 vaddr 0x00006314 paddr 0x00006314 align 2**2 filesz 0x000000e0 memsz 0x000000e0 flags rw- EH_FRAME off 0x00004a00 vaddr 0x00004a00 paddr 0x00004a00 align 2**2 filesz 0x00000154 memsz 0x00000154 flags r-- Dynamic Section: NEEDED libstdc++.so.5 NEEDED libm.so.6 NEEDED libgcc_s.so.1 NEEDED libc.so.6 SONAME EpsonFiscalProtocol.so INIT 0x00001cb4 FINI 0x00004994 HASH 0x000000b4 STRTAB 0x00000da4 SYMTAB 0x000004f4 STRSZ 0x00000acf SYMENT 0x00000010 PLTGOT 0x0000640c PLTRELSZ 0x00000270 PLTREL 0x00000011 JMPREL 0x00001a44 REL 0x000019dc RELSZ 0x00000068 RELENT 0x00000008 VERNEED 0x0000198c VERNEEDNUM 0x00000002 VERSYM 0x00001874 RELCOUNT 0x00000004 Version References: required from libstdc++.so.5: 0x056bafd2 0x00 04 CXXABI_1.2 required from libc.so.6: 0x09691f73 0x00 03 GLIBC_2.1.3 0x0d696910 0x00 02 GLIBC_2.0 So I suspect the main diference is the GCC_3.0 symbol I compile libcom_tichile_EpsonSerialDriver.so with the following command ( from memory as I not at work right now ) g++ -Wl,-soname=.... -shared -I/*jni libraries*/ -o libcom_tichile_jpos_EpsonSerialDriver -lEpsonFiscalProtocol -lpthread Is there any way to tell g++ to use that symbol version? Or any idea in how to make it work? EDIT: I have another non-working version with the followin dump: Program Header: LOAD off 0x00000000 vaddr 0x00000000 paddr 0x00000000 align 2**12 filesz 0x0000bf68 memsz 0x0000bf68 flags r-x LOAD off 0x0000cc0c vaddr 0x0000cc0c paddr 0x0000cc0c align 2**12 filesz 0x000005e8 memsz 0x00044df0 flags rw- DYNAMIC off 0x0000cc20 vaddr 0x0000cc20 paddr 0x0000cc20 align 2**2 filesz 0x000000f8 memsz 0x000000f8 flags rw- EH_FRAME off 0x0000b310 vaddr 0x0000b310 paddr 0x0000b310 align 2**2 filesz 0x000002bc memsz 0x000002bc flags r-- STACK off 0x00000000 vaddr 0x00000000 paddr 0x00000000 align 2**2 filesz 0x00000000 memsz 0x00000000 flags rw- RELRO off 0x0000cc0c vaddr 0x0000cc0c paddr 0x0000cc0c align 2**0 filesz 0x000003f4 memsz 0x000003f4 flags r-- Dynamic Section: NEEDED EpsonFiscalProtocol.so NEEDED libpthread.so.0 NEEDED libstdc++.so.6 NEEDED libm.so.6 NEEDED libgcc_s.so.1 NEEDED libc.so.6 SONAME libcom_tichile_jpos_EpsonSerialDriver.so INIT 0x000055d8 FINI 0x0000a968 HASH 0x000000f4 GNU_HASH 0x00000a30 STRTAB 0x00002870 SYMTAB 0x00001410 STRSZ 0x00002339 SYMENT 0x00000010 PLTGOT 0x0000cff4 PLTRELSZ 0x00000168 PLTREL 0x00000011 JMPREL 0x00005470 REL 0x00004ea8 RELSZ 0x000005c8 RELENT 0x00000008 VERNEED 0x00004e38 VERNEEDNUM 0x00000002 VERSYM 0x00004baa RELCOUNT 0x00000001 Version References: required from libstdc++.so.6: 0x056bafd3 0x00 05 CXXABI_1.3 0x08922974 0x00 03 GLIBCXX_3.4 required from libc.so.6: 0x09691f73 0x00 06 GLIBC_2.1.3 0x0d696914 0x00 04 GLIBC_2.4 0x0d696910 0x00 02 GLIBC_2.0 Now I think the main difference is in the GCC_3.0 symbol/ABI EDIT: Luckily, a coworker found a way to talk to the printer using Java

  Read the article

• fetching rss feed, mktime problem (wordpress plugin)

  - by krike

  sorry for the weird question but actually I'm not sure how to ask this. the code works fine but the problem is the following. I fetch items from feeds and compare them to a specific date which is stored into the database as an option. I see if the fetched item is more recent or not and if it is I create a new pending post. however there is one item that just keeps being added because there is something wrong with the date and I don't understand what is wrong because all other items (before and after) are blocked once they are being added as post (so when they are not recent anymore compared with the date I store as an option) I then echo'ed that line and this is the result: yes it exist! 27-03-2010-04-03 Free Exclusive Vector Icon Pack: Web User Interface 29-01-2010-03-01 if(1330732800 < 1335830400) 01 05 2012 the first line is to see if the option still exist and what data was stored in it the second is the actual items that's causing all the problem, it's initial date is less recent then the date but still passes as more recent.... this is the code I use, any help would be great: if(!get_option('feed_last_date')): echo "nope doesn't exist, but were creating one"; $time = time()-60*60*24*30*3; add_option("feed_last_date", date('d-m-Y-h-m', $time)); else: echo "yes it exist! ".get_option('feed_last_date'); endif; //Create new instance of simple pie and pass in feed link $feed = new SimplePie($feeds); //Call function handle_content_type() $feed->handle_content_type(); $last_date = explode("-", get_option('feed_last_date')); $day = $last_date[0]; $month = $last_date[1]; $year = $last_date[2]; $hour = $last_date[3]; $minute = $last_date[4]; $last_date = mktime(0,0,0, $day, $month, $year); //4 - Loop through received items foreach($feed->get_items(0, 500) as $item) : $feed_date = explode("-", $item->get_date('d-m-Y-h-m')); $day = $feed_date[0]; $month = $feed_date[1]; $year = $feed_date[2]; $hour = $feed_date[3]; $minute = $feed_date[4]; $feed_date = mktime(0,0,0,$day, $month, $year); if($last_date < $feed_date): echo $item->get_title()." ". $item->get_date('d-m-Y-h-m') ." if(".$last_date." < ".$feed_date.") <b>".date("d m Y", $feed_date)."</b><br />"; //if datum is newer then stored in database, then create new post $description = "<h3>download the resource</h3><p><a href='".$item->get_permalink()."' target='_blank'>".$item->get_permalink()."</a></p><h3>Resource description</h3><p>".$item->get_description()."</p>"; $new_post = array( 'post_title' => $item->get_title(), 'post_content' => $description, 'post_status' => 'pending', 'post_date' => date('Y-m-d H:i:s'), 'post_author' => $user_ID, 'post_type' => 'post', 'post_category' => array(0) ); $post_id = wp_insert_post($new_post); endif; endforeach; update_option("feed_last_date", date('d-m-Y-h-m', time()));

  Read the article

• Sorting an XML file through XSL

  - by jbugeja

  I have an XML file that I want to sort by an attribute. The file is structured as shown below: <wb xmlns:cf="http://www.macromedia.com/2004/cfform"> <a:form name="chart"> <a:input FIELDNUMBER="09" INDEX="2" LEFT="200" /> <a:input FIELDNUMBER="08" INDEX="3" LEFT="200" /> <a:fieldset FIELD="a" FIELDNAME="FieldSet1"> <a:input FIELDNUMBER="02" INDEX="4" LEFT="200" /> <a:select1 FIELDNUMBER="01" /> </a:fieldset> <a:fieldset FIELD="b" FIELDNAME="FieldSet1"> <a:input FIELDNUMBER="04" INDEX="7" LEFT="200" /> <a:select1 FIELDNUMBER="03" /> <a:fieldset FIELD="c" FIELDNAME="FieldSet1"> <a:input FIELDNUMBER="06" INDEX="8" LEFT="200" /> <a:input FIELDNUMBER="05" INDEX="6" LEFT="200" /> </a:fieldset> </a:fieldset> </a:form> </wb> I would like to sort the above XML all throughout by @fieldnumber, but at the same I want to keep the same structure of the XML. I have managed to sort other XML file but they did not have such nesting levels. Is this possible with XSL alone and if so how can this be done? The output should be as follows: <wb xmlns:cf="http://www.macromedia.com/2004/cfform"> <a:form name="chart"> <a:input FIELDNUMBER="08" INDEX="3" LEFT="200" /> <a:input FIELDNUMBER="09" INDEX="2" LEFT="200" /> <a:fieldset FIELD="a" FIELDNAME="FieldSet1"> <a:select1 FIELDNUMBER="01" /> <a:input FIELDNUMBER="02" INDEX="4" LEFT="200" /> </a:fieldset> <a:fieldset FIELD="b" FIELDNAME="FieldSet1"> <a:select1 FIELDNUMBER="03" /> <a:input FIELDNUMBER="04" INDEX="7" LEFT="200" /> <a:fieldset FIELD="c" FIELDNAME="FieldSet1"> <a:input FIELDNUMBER="05" INDEX="6" LEFT="200" /> <a:input FIELDNUMBER="06" INDEX="8" LEFT="200" /> </a:fieldset> </a:fieldset> </a:form> </wb> As another example, should the FIELDNUMBER 04 be changed to a value greater than 7 such as 10 (let's assume 10 in this example) then the output of the fieldset with FIELD value b becomes: <a:fieldset FIELD="b" FIELDNAME="FieldSet1"> <a:select1 FIELDNUMBER="03" /> <a:fieldset FIELD="c" FIELDNAME="FieldSet1"> <a:input FIELDNUMBER="05" INDEX="6" LEFT="200" /> <a:input FIELDNUMBER="06" INDEX="8" LEFT="200" /> </a:fieldset> <a:input FIELDNUMBER="10" INDEX="7" LEFT="200" /> </a:fieldset>

  Read the article

• SATA errors reported during boot: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0

  - by digby280

  I have noticed some error during the Linux boot. They seem to continue to occur after the boot adding lines to the log every few seconds. Once booted this normally does not appear to be causing any problems. However, around 1 in 10 boots results in a kernel panic and the computer has on two or three occasions suddenly rebooted after being powered on for a number of hours. I presume the cause of the reboot is a kernel panic as well. I am running Ubuntu 11.10 and I have had Ubuntu installed on the computer for around a year. I have googled around and not found anything useful. I have provided the kernel log lines and the output of smartctl. Can anyone explain exactly what these errors mean, or better still how to resolve them? Apr 2 16:51:27 dell580 kernel: [ 19.831140] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:27 dell580 kernel: [ 19.934194] tg3 0000:03:00.0: eth0: Link is down Apr 2 16:51:28 dell580 kernel: [ 20.929468] tg3 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex Apr 2 16:51:28 dell580 kernel: [ 20.929471] tg3 0000:03:00.0: eth0: Flow control is on for TX and on for RX Apr 2 16:51:28 dell580 kernel: [ 20.929727] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Apr 2 16:51:29 dell580 kernel: [ 21.609381] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:29 dell580 kernel: [ 21.616515] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:29 dell580 kernel: [ 21.616519] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:29 dell580 kernel: [ 21.616525] ata2.00: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 21.934036] ata2.01: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 22.408890] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.408907] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.440934] ata2.00: configured for UDMA/100 Apr 2 16:51:29 dell580 kernel: [ 22.449040] ata2.01: configured for UDMA/133 Apr 2 16:51:29 dell580 kernel: [ 22.449818] ata2: EH complete Apr 2 16:51:33 dell580 kernel: [ 26.122664] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:33 dell580 kernel: [ 26.122670] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:33 dell580 kernel: [ 26.122677] ata2.00: hard resetting link Apr 2 16:51:33 dell580 kernel: [ 26.442684] ata2.01: hard resetting link Apr 2 16:51:34 dell580 kernel: [ 26.925545] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.925561] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.961542] ata2.00: configured for UDMA/100 Apr 2 16:51:34 dell580 kernel: [ 26.969616] ata2.01: configured for UDMA/133 Apr 2 16:51:34 dell580 kernel: [ 26.970400] ata2: EH complete Apr 2 16:51:35 dell580 kernel: [ 28.111180] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:35 dell580 kernel: [ 28.111184] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:35 dell580 kernel: [ 28.111191] ata2.00: hard resetting link Apr 2 16:51:35 dell580 kernel: [ 28.429674] ata2.01: hard resetting link Apr 2 16:51:36 dell580 kernel: [ 28.904557] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.904572] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.936609] ata2.00: configured for UDMA/100 Apr 2 16:51:36 dell580 kernel: [ 28.944692] ata2.01: configured for UDMA/133 Apr 2 16:51:36 dell580 kernel: [ 28.945464] ata2: EH complete Apr 2 16:51:38 dell580 kernel: [ 31.581756] eth0: no IPv6 routers present Apr 2 16:51:38 dell580 kernel: [ 32.103066] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:38 dell580 kernel: [ 32.103074] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:38 dell580 kernel: [ 32.103085] ata2.00: hard resetting link Apr 2 16:51:38 dell580 kernel: [ 32.419669] ata2.01: hard resetting link Apr 2 16:51:39 dell580 kernel: [ 32.894518] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.894533] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.926536] ata2.00: configured for UDMA/100 Apr 2 16:51:39 dell580 kernel: [ 32.934715] ata2.01: configured for UDMA/133 Apr 2 16:51:39 dell580 kernel: [ 32.935578] ata2: EH complete Here's the output of smartctl for the drive. smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-17-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD103UJ Serial Number: S13PJ90QC19706 LU WWN Device Id: 5 0000f0 00b1c7960 Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Mon Apr 2 17:13:48 2012 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: (11772) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 197) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 7940 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 521 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 642 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 482 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 759 184 End-to-End_Error 0x0033 100 100 000 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 073 069 000 Old_age Always - 27 (Min/Max 16/27) 194 Temperature_Celsius 0x0022 073 067 000 Old_age Always - 27 (Min/Max 16/28) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 320028 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 099 099 000 Old_age Always - 1494 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 211 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 211 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 0f 31 63 8f e1 Error: ICRC, ABRT 15 sectors at LBA = 0x018f6331 = 26174257 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 40 62 8f e1 08 00:01:00.460 READ DMA c8 00 20 00 7c 30 e0 08 00:01:00.450 READ DMA c8 00 00 10 49 8f e1 08 00:01:00.440 READ DMA c8 00 e0 20 d0 30 e0 08 00:01:00.420 READ DMA c8 00 00 c0 59 90 e1 08 00:01:00.400 READ DMA Error 210 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 cf e9 cf 66 e0 Error: ICRC, ABRT 207 sectors at LBA = 0x0066cfe9 = 6737897 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 b8 cf 66 e0 08 00:08:29.780 READ DMA c8 00 60 60 c9 18 e0 08 00:08:29.770 READ DMA c8 00 40 20 c9 18 e0 08 00:08:29.770 READ DMA c8 00 20 00 c9 18 e0 08 00:08:29.760 READ DMA c8 00 20 98 cf 66 e0 08 00:08:29.750 READ DMA Error 209 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 2f d1 74 e0 e0 Error: ICRC, ABRT 47 sectors at LBA = 0x00e074d1 = 14709969 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 00 74 e0 e0 08 00:00:30.940 READ DMA c8 00 20 18 36 de e0 08 00:00:30.930 READ DMA c8 00 08 48 f1 dd e0 08 00:00:30.930 READ DMA c8 00 08 a8 f0 dd e0 08 00:00:30.930 READ DMA c8 00 08 90 f0 dd e0 08 00:00:30.930 READ DMA Error 208 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 7f 21 88 9d e0 Error: ICRC, ABRT 127 sectors at LBA = 0x009d8821 = 10324001 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 a0 00 88 9d e0 08 00:00:27.610 READ DMA c8 00 58 a8 e7 9c e0 08 00:00:27.610 READ DMA c8 00 00 28 e6 9c e0 08 00:00:27.610 READ DMA c8 00 00 e0 e4 9c e0 08 00:00:27.610 READ DMA c8 00 00 90 e0 9c e0 08 00:00:27.600 READ DMA Error 207 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 26 6a 6a c3 e0 Error: ABRT at LBA = 0x00c36a6a = 12806762 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 00 90 69 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 68 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 50 65 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 d0 64 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 63 c3 e0 08 00:29:39.350 WRITE DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 638 - # 2 Short offline Interrupted (host reset) 90% 638 - # 3 Extended offline Interrupted (host reset) 90% 638 - # 4 Short offline Interrupted (host reset) 90% 638 - # 5 Extended offline Interrupted (host reset) 90% 638 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

  Read the article

• Using a portable USB monitor in Ubuntu 13.04 (AOC e1649Fwu - DisplayLink)

  Having access to a little bit of IT hardware extravaganza isn't that easy here in Mauritius for exactly two reasons - either it is simply not available or it is expensive like nowhere. Well, by chance I came across an advert by a local hardware supplier and their offer of the week caught my attention - a portable USB monitor. Sounds cool, and the specs are okay as well. It's completely driven via USB 2.0, has a light weight, the dimensions would fit into my laptop bag and the resolution of 1366 x 768 pixels is okay for a second screen. Long story, short ending: I called them and only got to understand that they are out of stock - how convenient! Well, as usual I left some contact details and got the regular 'We call you back' answer. Surprisingly, I didn't receive a phone call as promised and after starting to complain via social media networks they finally came back to me with new units available - and *drum-roll* still the same price tag as promoted (and free delivery on top as one of their employees lives in Flic en Flac). Guess, it was a no-brainer to get at least one unit to fool around with. In worst case it might end up as image frame on the shelf or so... The usual suspects... Ubuntu first! Of course, the packing mentions only Windows or Mac OS as supported operating systems and without hesitation at all, I hooked up the device on my main machine running on Ubuntu 13.04. Result: Blackout... Hm, actually not the situation I was looking for but okay can't be too difficult to get this piece of hardware up and running. Following the output of syslogd (or dmesg if you prefer) the device has been recognised successfully but we got stuck in the initialisation phase. Oct 12 08:17:23 iospc2 kernel: [69818.689137] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 12 08:17:23 iospc2 kernel: [69818.800306] usb 2-4: device descriptor read/64, error -32Oct 12 08:17:24 iospc2 kernel: [69819.043620] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 08:17:24 iospc2 kernel: [69819.043630] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 08:17:24 iospc2 kernel: [69819.043636] usb 2-4: Product: e1649FwuOct 12 08:17:24 iospc2 kernel: [69819.043642] usb 2-4: Manufacturer: DisplayLinkOct 12 08:17:24 iospc2 kernel: [69819.043647] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 08:17:24 iospc2 kernel: [69819.046073] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 08:17:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 08:17:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 12 08:17:30 iospc2 kernel: [69825.411220] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 12 08:17:30 iospc2 kernel: [69825.498778] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 12 08:17:30 iospc2 kernel: [69825.498786] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 12 08:17:30 iospc2 kernel: [69825.498909] usbcore: registered new interface driver udl The device has been recognised as USB device without any question and it is listed properly: # lsusb...Bus 002 Device 005: ID 17e9:4107 DisplayLink ... A quick and dirty research on the net gave me some hints towards the udlfb framebuffer device for USB DisplayLink devices. By default this kernel module is blacklisted $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udl#blacklist udlblacklist udlfb and it is recommended to load it manually. So, unloading the whole udl stack and giving udlfb a shot: Oct 12 08:22:31 iospc2 kernel: [70126.642809] usbcore: registered new interface driver udlfb But still no reaction on the external display which supposedly should have been on and green. Display okay? Test run on Windows Just to be on the safe side and to exclude any hardware related defects or whatsoever - you never know what happened during delivery. I moved the display to a new position on the opposite side of my laptop, installed the display drivers first in Windows Vista (I know, I know...) as recommended in the manual, and then finally hooked it up on that machine. Tada! Display has been recognised correctly and I have a proper choice between cloning and extending my desktop. Testing whether the display is working properly - using Windows Vista Okay, good to know that there is nothing wrong on the hardware side just software... Back to Ubuntu - Kernel too old Some more research on Google and various hits recommend that the original displaylink driver has been merged into the recent kernel development and one should manually upgrade the kernel image (and both header) packages for Ubuntu. At least kernel 3.9 or higher would be necessary, and so I went out to this URL: http://kernel.ubuntu.com/~kernel-ppa/mainline/ and I downloaded all the good stuff from the v3.9-raring directory. The installation itself is easy going via dpkg: $ sudo dpkg -i linux-image-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb$ sudo dpkg -i linux-headers-3.9.0-030900_3.9.0-030900.201304291257_all.deb$ sudo dpkg -i linux-headers-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb As with any kernel upgrades it is necessary to restart the system in order to use the new one. Said and done: $ uname -r3.9.0-030900-generic And now connecting the external display gives me the following output in /var/log/syslog: Oct 12 17:51:36 iospc2 kernel: [ 2314.984293] usb 2-4: new high-speed USB device number 6 using ehci-pciOct 12 17:51:36 iospc2 kernel: [ 2315.096257] usb 2-4: device descriptor read/64, error -32Oct 12 17:51:36 iospc2 kernel: [ 2315.337105] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 17:51:36 iospc2 kernel: [ 2315.337115] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 17:51:36 iospc2 kernel: [ 2315.337122] usb 2-4: Product: e1649FwuOct 12 17:51:36 iospc2 kernel: [ 2315.337127] usb 2-4: Manufacturer: DisplayLinkOct 12 17:51:36 iospc2 kernel: [ 2315.337132] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338292] udlfb: DisplayLink e1649Fwu - serial #FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338299] udlfb: vid_17e9&pid_4107&rev_0129 driver's dlfb_data struct at ffff880117e59000Oct 12 17:51:36 iospc2 kernel: [ 2315.338303] udlfb: console enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338306] udlfb: fb_defio enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338309] udlfb: shadow enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338468] udlfb: vendor descriptor length:17 data:17 5f 01 0015 05 00 01 03 00 04Oct 12 17:51:36 iospc2 kernel: [ 2315.338473] udlfb: DL chip limited to 1500000 pixel modesOct 12 17:51:36 iospc2 kernel: [ 2315.338565] udlfb: allocated 4 65024 byte urbsOct 12 17:51:36 iospc2 kernel: [ 2315.343592] hid-generic 0003:17E9:4107.0009: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 17:51:36 iospc2 mtp-probe: checking bus 2, device 6: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 17:51:36 iospc2 mtp-probe: bus: 2, device: 6 was not an MTP deviceOct 12 17:51:36 iospc2 kernel: [ 2315.426583] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.426589] udlfb: Reallocating framebuffer. Addresses will change!Oct 12 17:51:36 iospc2 kernel: [ 2315.428338] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.428343] udlfb: set_par mode 1366x768Oct 12 17:51:36 iospc2 kernel: [ 2315.430620] udlfb: DisplayLink USB device /dev/fb1 attached. 1366x768 resolution. Using 4104K framebuffer memory Okay, that's looks more promising but still only blackout on the external screen... And yes, due to my previous modifications I swapped the blacklisted kernel modules: $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udlblacklist udl#blacklist udlfb Silly me! Okay, back to the original situation in which udl is allowed and udlfb blacklisted. Now, the logging looks similar to this and the screen shows those maroon-brown and azure-blue horizontal bars as described on other online resources. Oct 15 21:27:23 iospc2 kernel: [80934.308238] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 15 21:27:23 iospc2 kernel: [80934.420244] usb 2-4: device descriptor read/64, error -32Oct 15 21:27:24 iospc2 kernel: [80934.660822] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 15 21:27:24 iospc2 kernel: [80934.660832] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 15 21:27:24 iospc2 kernel: [80934.660838] usb 2-4: Product: e1649FwuOct 15 21:27:24 iospc2 kernel: [80934.660844] usb 2-4: Manufacturer: DisplayLinkOct 15 21:27:24 iospc2 kernel: [80934.660850] usb 2-4: SerialNumber: FJBD7HA000778Oct 15 21:27:24 iospc2 kernel: [80934.663391] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 15 21:27:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 15 21:27:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 15 21:27:25 iospc2 kernel: [80935.742407] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 15 21:27:25 iospc2 kernel: [80935.834403] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 15 21:27:25 iospc2 kernel: [80935.834416] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 15 21:27:25 iospc2 kernel: [80935.836389] usbcore: registered new interface driver udlOct 15 21:27:25 iospc2 kernel: [80936.021458] [drm] write mode info 153 Next, it's time to enable the display for our needs... This can be done either via UI or console, just as you'd prefer it. Adding the external USB display under Linux isn't an issue after all... Settings Manager => Display Personally, I like the console. With the help of xrandr we get the screen identifier first $ xrandrScreen 0: minimum 320 x 200, current 3200 x 1080, maximum 32767 x 32767LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm...DVI-0 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm   1366x768       60.0*+ and then give it the usual shot with auto-configuration. Let the system decide what's best for your hardware... $ xrandr --output DVI-0 --off$ xrandr --output DVI-0 --auto And there we go... Cloned output of main display: New kernel, new display... The external USB display works out-of-the-box with a Linux kernel > 3.9.0. Despite of a good number of resources it is absolutely not necessary to create a Device or Screen section in one of Xorg.conf files. This information belongs to the past and is not valid on kernel 3.9 or higher. Same hardware but Windows 8 Of course, I wanted to know how the latest incarnation from Redmond would handle the new hardware... Flawless! Most interesting aspect here: I did not use the driver installation medium on purpose. And I was right... not too long afterwards a dialog with the EULA of DisplayLink appeared on the main screen. And after confirmation of same it took some more seconds and the external USB monitor was ready to rumble. Well, and not only that one... but see for yourself. This time Windows 8 was the easiest solution after all. Resume I can highly recommend this type of hardware to anyone asking me. Although, it's dimensions are 15.6" it is actually lighter than my Samsung Galaxy Tab 10.1 and it still fits into my laptop bag without any issues. From now on... no more single screen while developing software on the road!

  Read the article

• ?????Exadata????

  - by Liu Maclean(???)

  ??check Exadata Image & OS versions , GI & DB patches sundiag exacheck cellserv ==> imageinfo dbhost ==> /usr/local/bin/imagehistory Also check the version of the switch. Login to Switch and execute the following command [root@myswitch-1 sbin]# version [root@dmorlsw-ib2 sbin]# cd /usr/local/bin [root@dmorlsw-ib2 bin]# ls -lrt version -rwxr-xr-x 1 root root 20356 Apr 4 2011 version Output will look as below. [root@dmorlsw-ib2 ~]# version SUN DCS 36p version: 1.3.3-2 Build time: Apr 4 2011 11:15:19 SP board info: Manufacturing Date: 2009.05.05 Serial Number: "NCD3X0178" Hardware Revision: 0x0006 Firmware Revision: 0x0102 BIOS version: NOW1R112 BIOS date: 04/24/2009 ib8# cat /sys/class/infiniband/is4_0/fw_ver 7.2.300 ib8 # cat /sys/class/dmi/id/bios_version NOW1R112 ib8 # nm2version NM2-36p version: 1.0.1-1 Build time: Sep 14 2009 12:52:51 ComExpress info: Manufacturing Date: 2009.08.19 Serial Number: Hardware Revision: 0x0006 Firmware Revision: 0x0102 { case `uname` in Linux ) ILOM="/usr/bin/ipmitool sunoem cli" ;; SunOS ) ILOM="/opt/ipmitool/bin/ipmitool sunoem cli" ;; esac ; ImageInfo="/opt/oracle.cellos/imageinfo" ; uname -srm ; head -1 /etc/*release ; uptime | cut -d, -f1 ; $ILOM "show /SP system_description system_identifier" | grep = ; $ImageInfo -activated -node -status -ver | grep -v ^$ ; } | tee /tmp/ExaInfo.log $GRID_HOME/OPatch/opatch lsinv -all -oh $GRID_HOME | tee /tmp/OPatchInv.log $ORACLE_HOME/OPatch/opatch lsinv -all | tee -a /tmp/OPatchInv.log cat /tmp/ExaInfo.log Linux 2.6.18-128.1.16.0.1.el5 x86_64 ==> /etc/enterprise-release <== Enterprise Linux Enterprise Linux Server release 5.3 (Carthage) ==> /etc/redhat-release <== Enterprise Linux Enterprise Linux Server release 5.3 (Carthage) 20:37:56 up 458 days system_description = SUN FIRE X4170 SERVER, ILOM v3.0.6.10.b, r52264 system_identifier = Sun Oracle Database Machine Active image version: 11.2.1.2.3 Active image activated: XXXX-XX-XX 12:27:12 +0800 Active image status: success Active node type: COMPUTE Inactive image version: undefined FileName: OPatchInv.log ---------------- ... Oracle Home       : /u01/app/11.2.0/grid Central Inventory : /u01/app/oraInventory   from           : /etc/oraInst.loc OPatch version    : 11.2.0.1.2 OUI version       : 11.2.0.1.0 OUI location      : /u01/app/11.2.0/grid/oui ... -------------------------------------------------------------------------------- List of Oracle Homes:   Name                                       Location   Ora11g_gridinfrahome1         /u01/app/11.2.0/grid   OraDb11g_home1                  /u01/app/oracle/product/11.2.0/dbhome_1 -------------------------------------------------------------------------------- Installed Top-level Products (1): Oracle Grid Infrastructure                                           11.2.0.1.0 ... Interim patches (2) : Patch  9524394      : applied on Thu Jun 03 20:46:05 CST 2010 ... {TRACKING BUG FOR 11.2.0.1 DB MACHINE BUNDLE PATCH 3} Patch  9455587      : applied on Fri Apr 02 18:27:47 CST 2010 ... {MERGE REQUEST ON TOP OF 11.2.0.1.0 FOR BUGS 8483425 8667622 8702731 8730804} Rac system comprising of multiple nodes  Local node = dbserv01  Remote node = dbserv02  Remote node = dbserv03  Remote node = dbserv04 -------------------------------------------------------------------------------- OPatch succeeded. ... Oracle Home       : /u01/app/oracle/product/11.2.0/dbhome_1 ... Oracle Database 11g                                                  11.2.0.1.0 ... Interim patches (5) : Patch  8888434      : applied on Sat Jan 08 00:27:33 CST 2011 ... {AIX-ASM-CF: LMHB TERMINATE INSTANCE WHEN OFFLINE ONE FAILGROUP IN ASM DG} Patch  8730312      : applied on Thu Jun 03 21:30:03 CST 2010 ... {FWD MERGE FOR BASE BUG 8715387 FOR 12G} Patch  9502717      : applied on Thu Jun 03 21:25:54 CST 2010 ... {LMS HIT ORA-600 [KJBLDRMNEXTPKEY:SEEN] AND CRASHED THE INSTANCE} { + same 2 as GI above} ?? cell server Cache Policy cell08# MegaCli64 -LDInfo -Lall -aALL | grep 'Current Cache Policy' Current Cache Policy: WriteThrough, ReadAheadNone, Direct, No Write Cache if Bad BBU cell09# MegaCli64 -LDInfo -Lall -aALL | grep 'Current Cache Policy' Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAheadNone, Direct, No Write Cache if Bad BBU Cache policy is in WB Would recommend proactive  battery repalcement. Example : a. /opt/MegaRAID/MegaCli/MegaCli64 -LDGetProp  -Cache -LALL -aALL ####( Will list the cache policy) b. /opt/MegaRAID/MegaCli/MegaCli64 -LDSetProp  -WB  -LALL -aALL ####( Will try to change teh policy from xx to WB)     So policy Change to WB will not come into effect immediately     Set Write Policy to WriteBack on Adapter 0, VD 0 (target id: 0) success     Battery capacity is below the threshold value ??cell BBU??????: cell08# /opt/MegaRAID/MegaCli/MegaCli64 -AdpBbuCmd -GetBbuStatus -a0 BBU status for Adapter: 0 BatteryType: iBBU Voltage: 4061 mV Current: 0 mA Temperature: 36 C BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : Yes Periodic Learn Required : No Battery state: GasGuageStatus: Fully Discharged : No Fully Charged : Yes Discharging : Yes Initialized : Yes Remaining Time Alarm : No Remaining Capacity Alarm: No Discharge Terminated : No Over Temperature : No Charging Terminated : No Over Charged : No Relative State of Charge: 99 % Charger System State: 49168 Charger System Ctrl: 0 Charging current: 0 mA Absolute state of charge: 21 % Max Error: 2 % Exit Code: 0x00 ????BBU ??: dcli -g ~/cell_group -l root -t '{ uname -srm ; head -1 /etc/*release ; uptime | cut -d, -f1 ; imagehistory ; ipmitool sunoem cli "show /SP system_description system_identifier" | grep = ; ipmitool sunoem cli "show /SP/policy FLASH_ACCELERATOR_CARD_INSTALLED /opt/MegaRAID/MegaCli/MegaCli64 -AdpBbuCmd -GetBbuStatus -a0 | egrep -i 'BBU|Battery|Charge:|Fully|Low|Learn' ; }' | tee /tmp/ExaInfo.log Target cells: ['cellserv01', 'cellserv02', 'cellserv03', 'cellserv04', 'cellserv05', 'cellserv06', 'cellserv07'] cellserv01: Linux 2.6.18-128.1.16.0.1.el5 x86_64 cellserv01: ==> /etc/enterprise-release <== cellserv01: Enterprise Linux Enterprise Linux Server release 5.3 (Carthage) cellserv01: cellserv01: ==> /etc/redhat-release <== cellserv01: Enterprise Linux Enterprise Linux Server release 5.3 (Carthage) cellserv01: 01:17:39 up 635 days cellserv01: Version : 11.2.1.2.1 cellserv01: Image activation date : 2011-03-25 11:59:34 -0800 cellserv01: Imaging mode : fresh cellserv01: Imaging status : success cellserv01: cellserv01: Version : 11.2.1.2.3 cellserv01: Image activation date : 2011-04-13 12:15:46 +0800 cellserv01: Imaging mode : patch cellserv01: Imaging status : success cellserv01: cellserv01: Version : 11.2.1.2.6 cellserv01: Image activation date : 2011-05-27 23:08:22 +0800 cellserv01: Imaging mode : patch cellserv01: Imaging status : success cellserv01: cellserv01: system_description = SUN FIRE X4275 SERVER, ILOM v3.0.6.10.b, r52264 cellserv01: system_identifier = Sun Oracle Database Machine cellserv01: Connected. Use ^D to exit. cellserv01: -> show /SP/policy FLASH_ACCELERATOR_CARD_INSTALLED cellserv01: show: No matching properties found. cellserv01: cellserv01: -> Session closed cellserv01: Disconnected cellserv01: BBU status for Adapter: 0 cellserv01: BatteryType: iBBU cellserv01: BBU Firmware Status: cellserv01: Learn Cycle Requested : No cellserv01: Learn Cycle Active : No cellserv01: Learn Cycle Status : OK cellserv01: Learn Cycle Timeout : No cellserv01: Battery Pack Missing : No cellserv01: Battery Replacement required : No cellserv01: Remaining Capacity Low : Yes cellserv01: Periodic Learn Required : No cellserv01: Battery state: cellserv01: Fully Discharged : No cellserv01: Fully Charged : Yes cellserv01: Relative State of Charge: 99 % cellserv01: Absolute state of charge: 21 % dcli -l root -g /root/all_group '/opt/MegaRAID/MegAaCli/MegaCli64 -AdpBbuCmd -a0' > BBU.out check ipmi: dcli -g ~/cell_group -l root -t '{ > ipmitool sunoem cli "show /SP/policy FLASH_ACCELERATOR_CARD_INSTALLED" | grep = ; MegaCli64 -LDInfo -Lall -aALL | grep 'Current Cache Policy' ; }' | tee /tmp/ExaCells.log

  Read the article

• Install Quartz.Net as a windows service and Test installation

  - by Tarun Arora

  In this blog post I’ll be covering, 01: Where to download Quartz.net from 02: How to install Quartz.net as a Windows service 03: Test the Quartz.net Installation If you are new to Quartz.net I would recommend reading the blog post on a brief introduction to Quartz.net. 01 – Where to download Quartz.net? http://sourceforge.net/projects/quartznet/files/quartznet/       Currently version  Quartz.Net 2.0.1 is the recommended download version. 02 – How to install Quartz.net as a Windows service         Go to the download location and unzip the Quartz.net package Navigate to the folder Quartz.Net \ Server \ bin – This is where you will find different .net version installers of the quartz.net packages. For example in the screen shot above, you can see the Quartz.net .net 3.5 and .net 4 packages. Open up the Quartz.net .net 4.0 folder, this folder contains the files you need to install Quartz.net as a windows service Copy the contents of the folder Downloads\Quartz.NET-2.0.1\server\bin\4.0 to the folder %program files%\Quartz.net   5. Open up a new CMD as an administrator and run the below command to install Quartz.net as a windows service /> Quartz.Server.exe install 6. How do I know that Quartz.Net service has installed as a Windows service? Go to run prompt and type ‘services.msc’ you should now see all the windows services installed on your machine. Navigate down to look for Quartz.Net. The service installs itself as an automatic startup Type and log on as ‘Local System’. You can easily change this to your prefer account that you would like to run the service as. If you wanted to name the Quartz service something else then that’s also possible… Can I change the default display name of the quartz.net windows service? Yes, you can! Navigate to C:\Program Files (x86)\Quartz.Net\ and open up the config file ‘quartz.config’ - You can change the instance name - You can change the default thread count of 10 - The port that the service listens to (by default this is port 555) A blog post on more configuration details can be found here. 03 – Test Quartz.Net windows service installation So, I have installed Quartz.Net as a windows service, how do I test whether my installation has been successful. Open up cmd as an administrator and run the below command, C:\Program Files (x86)\Quartz.Net> Quartz.Server.exe –i Since by default the Quartz.net windows service writes INFO level diagnostics (this can be changed from Quartz.Server.exe.config) you should see the service information show up on the console. For instance in the example above I can see that the service is running in a NON CLUSTERED mode, its currently not started and is currently in standby mode with 0 number of jobs executed so far… This was second in the series of posts on enterprise scheduling using Quartz.net, in the next post I’ll be covering how to run your first scheduled task using Quartz.net windows service. Thank you for taking the time out and reading this blog post. If you enjoyed the post, remember to subscribe to http://feeds.feedburner.com/TarunArora. Stay tuned!

  Read the article

• Java Resources for Windows Azure

  - by BuckWoody

  Windows Azure is a Platform as a Service – a PaaS – that runs code you write. That code doesn’t just mean the languages on the .NET platform – you can run code from multiple languages, including Java. In fact, you can develop for Windows and SQL Azure using not only Visual Studio but the Eclipse Integrated Development Environment (IDE) as well.  Although not an exhaustive list, here are several links that deal with Java and Windows Azure: Resource Link Windows Azure Java Development Center http://www.windowsazure.com/en-us/develop/java/  Java Development Guidance http://msdn.microsoft.com/en-us/library/hh690943(VS.103).aspx  Running a Java Environment on Windows Azure http://blogs.technet.com/b/port25/archive/2010/10/28/running-a-java-environment-on-windows-azure.aspx  Running a Java Environment on Windows Azure http://blogs.technet.com/b/port25/archive/2010/10/28/running-a-java-environment-on-windows-azure.aspx  Run Java with Jetty in Windows Azure http://blogs.msdn.com/b/dachou/archive/2010/03/21/run-java-with-jetty-in-windows-azure.aspx  Using the plugin for Eclipse http://blogs.msdn.com/b/craig/archive/2011/03/22/new-plugin-for-eclipse-to-get-java-developers-off-the-ground-with-windows-azure.aspx  Run Java with GlassFish in Windows Azure http://blogs.msdn.com/b/dachou/archive/2011/01/17/run-java-with-glassfish-in-windows-azure.aspx  Improving experience for Java developers with Windows  Azure http://blogs.msdn.com/b/interoperability/archive/2011/02/23/improving-experience-for-java-developers-with-windows-azure.aspx  Java Access to SQL Azure via the JDBC Driver for SQL  Server http://blogs.msdn.com/b/brian_swan/archive/2011/03/29/java-access-to-sql-azure-via-the-jdbc-driver-for-sql-server.aspx  How to Get Started with Java, Tomcat on Windows Azure http://blogs.msdn.com/b/usisvde/archive/2011/03/04/how-to-get-started-with-java-tomcat-on-windows-azure.aspx  Deploying Java Applications in Azure http://blogs.msdn.com/b/mariok/archive/2011/01/05/deploying-java-applications-in-azure.aspx  Using the Windows Azure Storage Explorer in Eclipse http://blogs.msdn.com/b/brian_swan/archive/2011/01/11/using-the-windows-azure-storage-explorer-in-eclipse.aspx  Windows Azure Tomcat Solution Accelerator http://archive.msdn.microsoft.com/winazuretomcat  Deploying a Java application to Windows Azure with  Command-line Ant http://java.interoperabilitybridges.com/articles/deploying-a-java-application-to-windows-azure-with-command-line-ant  Video: Open in the Cloud: Windows Azure and Java http://channel9.msdn.com/Events/PDC/PDC10/CS10  AzureRunMe  http://azurerunme.codeplex.com/  Windows Azure SDK for Java http://www.interoperabilitybridges.com/projects/windows-azure-sdk-for-java  AppFabric SDK for Java http://www.interoperabilitybridges.com/projects/azure-java-sdk-for-net-services  Information Cards for Java http://www.interoperabilitybridges.com/projects/information-card-for-java  Apache Stonehenge http://www.interoperabilitybridges.com/projects/apache-stonehenge  Channel 9 Case Study on Java and Windows Azure http://www.microsoft.com/casestudies/Windows-Azure/Gigaspaces/Solution-Provider-Streamlines-Java-Application-Deployment-in-the-Cloud/400000000081   

  Read the article

• Auto-cancel reason not found (6, 13906)

  - by Rajesh Sharma

  There are many errors in the application which are never invoked because of appropriate application configuration done at the time of implementation by the solution architects. So typically, as an application end user you would never stumble upon such errors. But what if the application administrator inadvertently changes the configuration/setup in the development, test, QA, or production environment? This is the time when you as an end user are introduced to a brand-new error for which you may not have a clue or understanding to what it means and neither the access/privilege to rectify it.    In this post we'll focus on one such error '6, 13906 - Auto-cancel reason not found'.   You get this error if you have not defined a Bill (Segment) Cancel Reason (Admin Menu, B, Bill Cancel Reason) code with System Default value of Turn off auto-cancel.   Consider a scenario when you are about to final bill an 'Account' for which the bill period's cut-off date you selected is falling on or after the Service Agreement's (SA) end/stop date (basically SA is Stopped with a date earlier than it was billed previously). And for the same 'Account' either: Bill segments exists that end after the SA's end date OR Non-closing bill segments exists that end on the SA's end date (OR closing bill segments that do not end on SA's end date or do not exist at all - remember closing/final bill segment is generated if the SA is in Stopped status).   CC&B detects such scenario and attempts to cancel all such violating bill segments automatically, but NOT if you are generating the bill Online. If online, the system assumes that you know what you are doing, and prompts you with error 2, 13716 - Bill segments that violate the SA (%1) End Date (%2) exist to take necessary action.   If in batch, system automatically cancels these kinds of bill segment(s).   Since this happens in the background, you have to define within the application which System Default Bill (Segment) cancellation reason code identified as Turn off auto-cancel, should be used by the process when it attempts to cancel any such violating bill segments (You already know that you cannot cancel a bill segment without giving a reason for cancellation).   So what exactly happens during batch billing?   Bill Segment generation routine at first determines billing eligibility of the service agreement being billed. One of the billing eligibility criteria is to check the SA's previous bill segments which have end dates greater than the current cut-off date/end date. Technically, the routine retrieves a count of such violating bill segments.     SELECT COUNT (*) FROM CI_BSEG WHERE SA_ID = :SA-ID AND BSEG_STAT_FLG = '50' -- Frozen AND END_DT IS NOT NULL AND (END_DT > '03-JUN-2010' -- Bill segment greater than SA's End Date OR OR (END_DT = '03-JUN-2010' AND CLOSING_BSEG_SW = 'N')) -- Non-closing bill segment ending on SA's end date   If the count is greater than zero, Bill segment generation routine executes another program to auto-cancel such bill segments. Auto-cancel program retrieves the 'Bill Cancel Reason' code which is identified as Turn off auto-cancel. Retrieved cancel reason code is then placed on the bill segments that are being cancelled automatically.   During this process if the routine fails to determine the bill cancel reason code having System Default Turn off auto-cancel because it was not been configured, you get a bill exception 6, 13906 - Auto-cancel reason not found.   Also note that duplicate or multiple System Default codes identified as Turn off auto-cancel are not allowed. CC&B would complain with an error 2, 54201.   Duplicate validation/check is also performed within Auto-cancel routine, if suppose for test purposes you executed a DML statement updating CI_BILL_CAN_RSN.BSCAN_SYS_DFLT_FLG with a value 'T'.

  Read the article

• Java Resources for Windows Azure

  - by BuckWoody

  Windows Azure is a Platform as a Service – a PaaS – that runs code you write. That code doesn’t just mean the languages on the .NET platform – you can run code from multiple languages, including Java. In fact, you can develop for Windows and SQL Azure using not only Visual Studio but the Eclipse Integrated Development Environment (IDE) as well.  Although not an exhaustive list, here are several links that deal with Java and Windows Azure: Resource Link Windows Azure Java Development Center http://www.windowsazure.com/en-us/develop/java/  Java Development Guidance http://msdn.microsoft.com/en-us/library/hh690943(VS.103).aspx  Running a Java Environment on Windows Azure http://blogs.technet.com/b/port25/archive/2010/10/28/running-a-java-environment-on-windows-azure.aspx  Running a Java Environment on Windows Azure http://blogs.technet.com/b/port25/archive/2010/10/28/running-a-java-environment-on-windows-azure.aspx  Run Java with Jetty in Windows Azure http://blogs.msdn.com/b/dachou/archive/2010/03/21/run-java-with-jetty-in-windows-azure.aspx  Using the plugin for Eclipse http://blogs.msdn.com/b/craig/archive/2011/03/22/new-plugin-for-eclipse-to-get-java-developers-off-the-ground-with-windows-azure.aspx  Run Java with GlassFish in Windows Azure http://blogs.msdn.com/b/dachou/archive/2011/01/17/run-java-with-glassfish-in-windows-azure.aspx  Improving experience for Java developers with Windows  Azure http://blogs.msdn.com/b/interoperability/archive/2011/02/23/improving-experience-for-java-developers-with-windows-azure.aspx  Java Access to SQL Azure via the JDBC Driver for SQL  Server http://blogs.msdn.com/b/brian_swan/archive/2011/03/29/java-access-to-sql-azure-via-the-jdbc-driver-for-sql-server.aspx  How to Get Started with Java, Tomcat on Windows Azure http://blogs.msdn.com/b/usisvde/archive/2011/03/04/how-to-get-started-with-java-tomcat-on-windows-azure.aspx  Deploying Java Applications in Azure http://blogs.msdn.com/b/mariok/archive/2011/01/05/deploying-java-applications-in-azure.aspx  Using the Windows Azure Storage Explorer in Eclipse http://blogs.msdn.com/b/brian_swan/archive/2011/01/11/using-the-windows-azure-storage-explorer-in-eclipse.aspx  Windows Azure Tomcat Solution Accelerator http://archive.msdn.microsoft.com/winazuretomcat  Deploying a Java application to Windows Azure with  Command-line Ant http://java.interoperabilitybridges.com/articles/deploying-a-java-application-to-windows-azure-with-command-line-ant  Video: Open in the Cloud: Windows Azure and Java http://channel9.msdn.com/Events/PDC/PDC10/CS10  AzureRunMe  http://azurerunme.codeplex.com/  Windows Azure SDK for Java http://www.interoperabilitybridges.com/projects/windows-azure-sdk-for-java  AppFabric SDK for Java http://www.interoperabilitybridges.com/projects/azure-java-sdk-for-net-services  Information Cards for Java http://www.interoperabilitybridges.com/projects/information-card-for-java  Apache Stonehenge http://www.interoperabilitybridges.com/projects/apache-stonehenge  Channel 9 Case Study on Java and Windows Azure http://www.microsoft.com/casestudies/Windows-Azure/Gigaspaces/Solution-Provider-Streamlines-Java-Application-Deployment-in-the-Cloud/400000000081   

  Read the article

• Slow wifi on Ubuntu 12.04 wifi driver ath9k

  - by lunar

  For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• EnOcean -> USB Serial Communication (C++)

  - by regorianer

  I guess it is not the right place to ask here for enocean specific details, but maybe I am doing something wrong by using serial connections and you can help me no matter if there is knowledge about this technology or not. I have a problem to communicate with the RCM152 Module. I have written a C++ program to communicate with the RCM152 by emulating packets of the PTM 200. I teach the RCM152 to listen to the following packets: [06/19/12 04:21:44.546] INFO: SENDING BYTE : 55 <-- start byte [06/19/12 04:21:44.546] INFO: SENDING BYTE : 00 <-- head begin [06/19/12 04:21:44.546] INFO: SENDING BYTE : 07 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 07 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 01 <-- head end [06/19/12 04:21:44.546] INFO: SENDING BYTE : 7a <-- CRC Check [06/19/12 04:21:44.546] INFO: SENDING BYTE : f6 <-- packet type [06/19/12 04:21:44.546] INFO: SENDING BYTE : 20 <-- My action (00 and 10 -> OFF, 20 and 30 -> ON) [06/19/12 04:21:44.546] INFO: SENDING BYTE : 00 <-- serial.byte 3 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 24 <-- serial.byte 2 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 21 <-- serial.byte 1 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 87 <-- serial.byte 0 [06/19/12 04:21:44.546] INFO: SENDING BYTE : 30 <-- status [06/19/12 04:21:44.546] INFO: SENDING BYTE : 03 <-- 03 for send, 01 for receiver [06/19/12 04:21:44.546] INFO: SENDING BYTE : ff <-- begin destination [06/19/12 04:21:44.546] INFO: SENDING BYTE : ff [06/19/12 04:21:44.546] INFO: SENDING BYTE : ff [06/19/12 04:21:44.546] INFO: SENDING BYTE : ff <-- end destination [06/19/12 04:21:44.546] INFO: SENDING BYTE : ff <-- Transmission quality (sender ff) [06/19/12 04:21:44.546] INFO: SENDING BYTE : 00 [06/19/12 04:21:44.547] INFO: SENDING BYTE : 10 <-- CRC Check A PTM200 Device or a SG-FUS-24-230 Device are sending equivalent packets like: [06/19/12 04:30:31.106] INFO: Received Byte: 55 [06/19/12 04:30:31.106] INFO: Received Byte: 00 [06/19/12 04:30:31.106] INFO: Received Byte: 07 [06/19/12 04:30:31.106] INFO: Received Byte: 07 [06/19/12 04:30:31.106] INFO: Received Byte: 01 [06/19/12 04:30:31.106] INFO: Received Byte: 7a [06/19/12 04:30:31.106] INFO: Received Byte: f6 [06/19/12 04:30:31.106] INFO: Received Byte: 40 [06/19/12 04:30:31.106] INFO: Received Byte: 00 [06/19/12 04:30:31.106] INFO: Received Byte: 24 [06/19/12 04:30:31.106] INFO: Received Byte: 6c [06/19/12 04:30:31.106] INFO: Received Byte: 2f [06/19/12 04:30:31.106] INFO: Received Byte: 30 [06/19/12 04:30:31.106] INFO: Received Byte: 01 [06/19/12 04:30:31.106] INFO: Received Byte: ff [06/19/12 04:30:31.106] INFO: Received Byte: ff [06/19/12 04:30:31.108] INFO: Received Byte: ff [06/19/12 04:30:31.108] INFO: Received Byte: ff [06/19/12 04:30:31.108] INFO: Received Byte: 37 [06/19/12 04:30:31.108] INFO: Received Byte: 00 [06/19/12 04:30:31.108] INFO: Received Byte: d1 I can control the device connected to the RCM152 like I want to with my sending packets (thats a good fact and means that the RCM152 has learned my packets and can use them. Also the actions (0x10 - ON, 0x30 - OFF) are working fine), but the problem is, that no matter which serial I choose, the RCM152 reacts to these packets. I only want to have actions if the teached-in serial is send and all other packets with different serials to be ignored. The RCM152 is not reacting to the packets sent by the PTM200 nor by the SG-FUS-24-230 because these are not teached-in. Thats exactly what I want to have with the packets created myself. What am I doing wrong? The libraries I am using are these for C++ http://pvbrowser.de/pvbrowser/sf/manual/rllib/html/ The enocean EEP says: For this purpose of a determined relationship between transmitter and receiver each transmitting device has a unique Sender-ID which is part of each radio telegram. The receiving device detects from the Sender-ID whether the device is known, i.e., was already learned, or unknown. A telegram with unknown Sender-ID is disregarded.

  Read the article

• how do i fix this: the networking and wireless are enabled. but list of networks under wireless networks not available

  - by Ayesha Ahmad

  i started working with ubuntu 11.10 last year. i upgraded to 12.04 a week back. since then i have had all sorts of problems with network connection. first had to install the new driver. the hardware switch somehow got disabled then the above problem arrived. even tho the options are all enabled, the OS is not able to detect scan available network connections. also i have to bring to notice that once in a while it does get connected, can not explain how it happens. I want to fix this problem once and for all. please help. ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:51:b3:c8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:44 eth1 Link encap:Ethernet HWaddr 1c:65:9d:67:d5:e1 inet6 addr: fe80::1e65:9dff:fe67:d5e1/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:170 TX packets:0 errors:27 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:344 errors:0 dropped:0 overruns:0 frame:0 TX packets:344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20336 (20.3 KB) TX bytes:20336 (20.3 KB) lshw -c network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 1c:65:9d:67:d5:e1 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: f0:4d:a2:51:b3:c8 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:196 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) I hope this information is of some help.

  Read the article

• Radeon Mobility HD 5470 Not Working on Ubuntu 10.10

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Radeon Mobility HD 5470 Not Working

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Errors when trying to compile the driver for the rtl8192su wireless adapter

  - by Tom Brito

  I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• How do I configure WakeOnUSB properly?

  - by wishi

  How do I configure Wake-On-USB properly on a 10.04 or 10.10 Ubuntu (2.6.36 and higher if needed)? (Wake-on-USB is when the computer is asleep and for example a USB Keyboard event wakes up the machine!) The notebook is an Acer Aspire Timeline X 1830T. I don't know in which way the Linux Kernel supports the controllers. There are different ways to approach this, for example /proc/acpi/wakeup... or UDEV... or something with HAL? /proc/acpi/wakeup shows every device in S4, but I need S3. Device S-state Status Sysfs node P0P2 S4 *disabled PEGP S4 *disabled P0P1 S0 *disabled pci:0000:00:1e.0 EHC1 S4 *disabled pci:0000:00:1d.0 USB1 S4 *enabled USB2 S4 *disabled USB3 S4 *disabled USB4 S4 *disabled EHC2 S4 *disabled pci:0000:00:1a.0 USB5 S4 *disabled USB6 S4 *disabled USB7 S4 *disabled HDEF S0 *disabled pci:0000:00:1b.0 RP01 S5 *disabled pci:0000:00:1c.0 PXSX S5 *disabled pci:0000:01:00.0 RP02 S0 *disabled pci:0000:00:1c.1 PXSX S5 *disabled pci:0000:02:00.0 RP03 S0 *disabled PXSX S5 *disabled RP04 S0 *disabled PXSX S5 *disabled RP05 S0 *disabled PXSX S5 *disabled RP07 S0 *disabled PXSX S5 *disabled RP08 S0 *disabled PXSX S5 *disabled GLAN S0 *disabled PEG3 S4 *disabled PEG5 S4 *disabled PEG6 S4 *disabled SLPB S3 *enabled S4, which is Suspend-To-Disk afaik... doesn't seem to work either if I echo USB1 into the wakeup table. It just sets an S4 flag. can I get the USB ports in S3? I want to make the machine wakeup from Suspend-To-Ram (S3, ACPI standard) in case a key on my external keyboard is pressed. It only wakes up if a key on the internal Laptop keyboard is pressed... from Suspend To Ram. It seems if I plug in a USB mouse, that the USB port isn't even powered. I have no BIOS option to change this. Further specific information regarding the device: usb-devices T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 13 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=04d9 ProdID=1603 Rev=03.10 S: Manufacturer= S: Product=USB Keyboard C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid root@underwater-laptop:/# lsusb [...] Bus 001 Device 013: ID 04d9:1603 Holtek Semiconductor, Inc. Bus 001 Device 004: ID 0bda:0138 Realtek Semiconductor Corp. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub [...] If this doesn't work I have to properly explain why :( - but I think it is very hard to research this kernel internal. Any hints for good information here? I hope it's possible... I'm just looking for any solution. edit: this, waking up on USB, works on Windows! Thanks a lot, Marius

  Read the article

• Getting the JSESSIONID from the response Headers in C#

  - by acadia

  Hello, In my C# Windows application I am building a web request and getting the response back Uri uri = null; string workplaceURL = "http://filenet:9081/WorkPlaceXT"; uri = new Uri(workplaceURL + "/setCredentials?op=getUserToken&userId=" + encodeLabel(userName) + "&password=" + encodeLabel(pwd) + "&verify=true"); System.Net.WebRequest webRequest = System.Net.WebRequest.Create(uri); System.Net.WebResponse webResponse = webRequest.GetResponse(); StreamReader streamReader = new StreamReader(webResponse.GetResponseStream()); and I am getting the headers back as shown below ?webResponse.Headers {ResultXml: <?xml version="1.0"?><response><errorcode>0</errorcode><description>Success.</description></response> Content-Language: en-US Content-Length: 201 Cache-Control: no-cache="set-cookie, set-cookie2" Date: Thu, 03 Jun 2010 16:10:12 GMT Expires: Thu, 01 Dec 1994 16:00:00 GMT Set-Cookie: JSESSIONID=0000GiPPR9PPceZSv6d0FC4-vcT:-1; Path=/ Server: WebSphere Application Server/6.1 } base {System.Collections.Specialized.NameValueCollection}: {ResultXml: <?xml version="1.0"?><response><errorcode>0</errorcode><description>Success.</description></response> Content-Language: en-US Content-Length: 201 Cache-Control: no-cache="set-cookie, set-cookie2" Date: Thu, 03 Jun 2010 16:10:12 GMT Expires: Thu, 01 Dec 1994 16:00:00 GMT Set-Cookie: JSESSIONID=0000GiPPR9PPceZSv6d0FC4-vcT:-1; Path=/ Server: WebSphere Application Server/6.1 How do I fetch just the JSESSIONID? as I need to pass the JSESSIOID to a different URL. Please help

  Read the article

• Problem with TimeZoneInfo.ConvertTime: missed the Daylight Saving switch.

  - by SirMoreno

  My web app runs on .Net 3.5, all of the dates are saved on the DB in UTC time (not in user time). When I want to display a date I convert it to user date (from UTC) //Get the current datetime of the user exp: GMT TO ISRAEL +2 public static DateTime GetUserDateTime(DateTime dateUTC) { string userTzId = "Israel Standard Time"; TimeZoneInfo userTZ = TimeZoneInfo.FindSystemTimeZoneById(userTzId); dateUTC = DateTime.SpecifyKind(dateUTC, DateTimeKind.Utc); DateTime ret = TimeZoneInfo.ConvertTime(dateUTC, TimeZoneInfo.Utc, userTZ); return ret; } Until now it worked fine but I have users from Israel (GMT +2), and Israel switched to Daylight saving time on 26/3/10 so now it's (GMT +3). For some reason the TimeZoneInfo.ConvertTime don't know the Daylight saving time switch is on 26/3/10 so it still converts to GMT +2. The strange thing is that on localhost it works fine, I set up a test page: DateTime userdate = GetUserDateTime(DateTime.UtcNow); string str2 = "UserDateTime = " + userdate.ToString("dd/MM/yy") + " " + userdate.ToString("HH:mm"); On the Server (windows 2003 set to UTC time) it shows the wrong time (+2): UserDateTime = 27/03/10 21:38 On localhost (windows XP set to Israel Time) it shows the correct time (+3): UserDateTime = 27/03/10 22:38 How can I update the TimeZoneInfo that the Daylight saving time switch in Israel was on the 26/3/10? Thanks.

  Read the article

• android DES decrypt file : pad block corrupted

  - by Kenny Chang

  public class TestDES { Key key; public TestDES(String str) { getKey(str); } public void getKey(String strKey) { try { KeyGenerator _generator = KeyGenerator.getInstance("DES"); _generator.init(new SecureRandom(strKey.getBytes())); this.key = _generator.generateKey(); _generator = null; } catch (Exception e) { throw new RuntimeException("Error initializing SqlMap class. Cause: " + e); } } public void decrypt(String file, String dest) throws Exception { Cipher cipher = Cipher.getInstance("DES"); cipher.init(Cipher.DECRYPT_MODE, this.key); InputStream is = new FileInputStream(file); OutputStream out = new FileOutputStream(dest); CipherOutputStream cos = new CipherOutputStream(out, cipher); byte[] buffer = new byte[1024 * 1024 * 6]; int r; while ((r = is.read(buffer)) >= 0) { cos.write(buffer, 0, r); } cos.close();a out.close(); is.close(); } } The code works well on PC JAVA Program, but not on android.The error "pad block corrupted" happended at 'cos.close();' LogCat shows:" 03-10 07:43:04.431: WARN/System.err(23765): java.io.IOException: pad block corrupted 03-10 07:43:04.460: WARN/System.err(23765): at javax.crypto.CipherOutputStream.close(CipherOutputStream.java:157) "

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >