Search Results

Search found 804 results on 33 pages for 'dylan wan'.

Page 26/33 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Passing OpenVPN road-warrior traffic through tunnel pfsense

  - by Chris

  I have a local LAN (10.100.100.0/24) and OpenVPN road-warriors (10.99.99.0/24). pfSense is regulating all this as follows: LAN: 10.100.100.105 WAN: 10.100.99.1 (connected to DSL Router which connects to internet). OPT1: 10.99.99.0 (OpenVPN tun0). There is an IPSec connection between my office and another office where my LAN can work on a specific IP address (sql server to be exact) on 192.168.30.41. My problem is that I wish my OpenVPN road-warrior clients to be able to use the IPSec service on 192.168.30.41 as well (which at present they cannot despite the fact that I am pushing the route 192.168.30.0 255.255.255.0). The other site's administrator cannot add the extra route for my openvpn clients for a lot of reasons which I am not going to enter at this stage. Is there a possibility that I could NAT all of my openVPN road-warriors requests through a local LAN IP address (something like 10.100.100.250 which is not used by anything on my LAN). The problem is that I am a newbie with pfSense so as much step-by-step help as possible would be very much appreciated! Thank you. C.

  Read the article

• Apache mod_rewrite weird behavior in Internet Explorer

  - by morrty

  I'm attempting to setup redirection for a couple of root domains. Firstly, here is the code in my httpd-vhosts.conf file: <VirtualHost *:80> ServerAdmin ****@example.com ServerName example.com ServerAlias example2.com RewriteEngine On RewriteCond %{HTTP_HOST} !^192\.168\.0\.1$ # This is our WAN IP RewriteCond %{HTTP_HOST} !^www\. [NC] RewriteCond %{HTTP_HOST} !^$ RewriteRule ^/?(.*) http://www.%{HTTP_HOST}/$1 [L,R,NE] </VirtualHost> What this does is redirect the root domain of example.com or example2.com or any host other than www to www.example(2).com The part I'm having a problem with is the RewriteRule itself. the $1 is supposed to match the pattern of the RewriteRule and add it in the substitution. For example: "http://example.com/test.html" should rewrite to "http://www.example.com/test.html" It works in all modern browsers like it's supposed to except for IE8 or IE9 (I didn't test other IE versions). In IE, this works: "http://example.com" to "http://www.example.com" In IE, this does not work: "http://example.com/test.html" to "http://www.example.com/test.html" Does anyone have an explanation for this behavior? I hope I've explained it well enough. Thank you.

  Read the article

• Ping: sendmsg: operation not permitted error after installing iptables on Arch GNU/Linux

  - by estol

  Yesterday I got a new computer as my homeserver, a HP Proliant Microserver. Installed Arch Linux on it, with kernel version 3.2.12. After installing iptables (1.4.12.2 - the current version afaik) and changing the net.ipv4.ip_forward key to 1, and enabling forwarding in the iptables configuration file (and rebooting), the system cannot use any of its network itnerfaces. Ping fails with Ping: sendmsg: operation not permitted If I remove iptables completely, networking is okay, but I need to share the Internet connection to the local network. eth0 - wan NIC integrated on the motherboard (no idea of vendor, probably HP). eth1 - lan NIC in a pci-express slot (Intel Gigabit CT Desktop http://www.intel.com/content/www/us/en/network-adapters/gigabit-network-adapters/gigabit-ct-desktop-adapter.html) Since it works without iptables(server can access the internet, and I can login with ssh from the internal network), I assume it has something to do with iptables. I do not have much experience with iptables, so I used these as reference (separate from each other of course...): wiki.archlinux.org/index.php/Simple_stateful_firewall#Setting_up_a_NAT_gateway revsys.com/writings/quicktips/nat.html howtoforge.com/nat_iptables On my previous server, I used the revsys guide to set up nat, worked like a charm. Anyone experienced anything like this before? What am I doing wrong? Thanks, estol

  Read the article

• Is one server on a vlan unnecessary?

  - by moomoochoo

  DETAILS I've been researching web hosting solutions in Japan. Based on this question one of the services available seems to be a VLAN. I've read about the advantages of such a system for a large organization, but there doesn't seem to be much information regarding smaller setups. I take that to mean that for one server it is likely to be unnecessary? My concern is that I don't know how many other servers are on the WAN, so regardless of how many servers I use a VLAN might still be a good idea. SERVER INFO One dedicated server would be used. It would not be virtualized. My Research so far Based on comments here, a VLAN would be useful for mitigating these problems. A user on another server could, either mistakenly or maliciously, assign one of your IP addresses to their server, resulting in a "duplicate IP" situation that would cause connectivity issues. A user on another server could poison the arp cache and potentially redirect traffic to snoop on communication intended to/from your server. (later in the discussion this point was said to be unrealistic.) QUESTION Is it worthwhile getting a vlan for one dedicated server? Will it be easier/the same/ harder to manage?

  Read the article

• Joining two routers together, but I have no access to the second router, although I know it's IP address and Gateway

  - by JohnnyVegas

  I have temporarily moved into a rented apartment for 4 months, which has wireless. The trouble I am having is that the access points here are wifi only and no RJ45 and I need to use RJ45 to connect some equipment that I am working with. I have purchased an RT-N66U and installed Tomato (shibby ver. 1.28) and successfully replaced the existing access point, but now I want to enable the access point that I have replaced as it links wirelessly to 3 others. Can I plug in a cable from the access point to my RT-N66U and get it to access the internet via my router? I have no access to the existing wireless access point, and don't want to reset it as it's not mine. There is another router situated in the roof somewhere which I also have no access to, but it's supplying my RT-N66U internet and I most definitely have a double-nat, which although isn't the best way of doing things I am limited with what I can do. Any suggestions on routing tables, vlans etc would be helpful, but I have no experience in these fields before - but I know the tomato firmware can cater for this. My router is set to IP 10.0.1.1 and dhcp is 10.0.1.100-200 The wireless access point address was 192.168.1.2 but this was assigned by the router in the roof which has the address 192.168.1.1. There is a cable from this router going to a wall socket which I now have my RT-N66u attached to via the WAN port. I understand it's scruffy and it isn't the way to do things but I have tried to ask for the admin details but as the wireless network is looked after by a third party and nobody knows their details I am stuck with this dilemma. I could buy three wireless access points and replace the existing but this isn't what I want to do, and although I have installed plenty of DD-WRT wireless repeater bridges they simply don't work here for some unknown reason. The phone line here is very noisy too and I don't have the rights to install ADSL in a building that isn't mine, and 3G coverage isn't good enough either. Thanks for your time

  Read the article

• DHCP not responding from laptop or router, but works on directly plugged PC?

  - by Matt H

  I'm at my sister in law's place in Singapore. I'm not from Singapore but am here for a few months. She has some sort of cable modem made by motorolla (SB5101 Surfboard). I think it goes, through starhub or similar provider. Anyhow, her PC is directly attached by cable (not wireless) and she can access the internet. There is no wireless router connected to it. The PC is configured with DHCP and appears to be working. However, the moment I unplug her PC and plug in my laptop, it doesn't get an address. The interesting thing here is that I also see this toredo tunnel adaptor etc. I'm not familiar with what that is. It appears to be being assigned an IP v6 address and an IP v4 address. I thought perhaps it's my laptop, but also when I plug in my DDWRT based router, it also fails to get a DHCP assigned address on the WAN port. I can't also seem to connect into any web configuration on the motorolla modem either. Any ideas? what kind of setup is this? all I'd like to do is plug in my wireless router so I can roam around the house and also access the internet.

  Read the article

• Terminal server performance over high latency links

  - by holz

  Our datacenter and head office is currently in Brisbane, Australia, and we have a branch office in the UK. We have a private WAN with a 768k link to our UK office and the latency is at about 350ms. The terminal server performance is reeeeealy bad. Applications that don't have too much animation or any images seem to be okay. But as soon as they do, the session is almost unusable. Powerpoint and internet explorer are good examples of apps that make it run slow. And if there is an image in your email signature, outlook will hang for about 10 seconds each time a new line is inserted, while the image gets moved down a few pixels. We are currently running server 2003. I have tried Server 2008 R2 RDS, and also a third party solution called Blaze by a company called Ericom, but it is still not too much better. We currently have a 5 levels dynamic class of service with the priority in the following order. VoIP Video Terminal Services Printing Everything else When testing the terminal server performance, the link monitored using net-flows, and have plenty we of bandwidth available, so I believe that it is a latency issue rather than bandwidth. Is there anything that can be done to improve performance. Would citrix help at all?

  Read the article

• Route forwarded traffic through eth0 but local traffic through tun0

  - by Ross Patterson

  I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

  Read the article

• Convert a Linksys WAG54GP2 ADSL router into Access point only to extend my Wifi range

  - by Preet Sangha

  I have a wireless lan running on my ASDL2 connection. The router (Seimens Gigaset sx763) is provided by the ISP and is generally good. However I have couple of dead spots at the far end of the house and since I have my old router sitting in the drawer I thought that I'd try to convert it into simple WAP. However downloading the manual from linksys it seems to be that the manual is from an earlier firmware, but the very first option on the very first page seems promising: Wan Mode: Router or ADSL However after this I'm a bit lost. I know that the wireless card on this box will need a mac address and it must get its address from the master router (I thought static might be best). However the again the manual is out of date I have the option of DHCP: ON or OFF or RELAY I've not even got to the more complex options yet. Question is can this device even work this way (seems like it but I cannot find any docs on it), and if so how? Edit: Having now fiddled around I'm of the opinion that this cannot be done.

  Read the article

• How this could happen to my ftp server?

  - by srisar

  hi, again me, i just dont get why i m getting this message, when i try to connect my ftp server thorugh my wan address (112.135.26.115) its saying me, 530 user access denied but when i give the same data to http://ftptest.net the result is as follows... Status: Resolving address of 112.135.26.115 Status: Connecting to 112.135.26.115 Status: Connected, waiting for welcome message Reply: 220-FileZilla Server version 0.9.34 beta Reply: 220-written by Tim Kosse ([email protected]) Reply: 220 Please visit http://sourceforge.net/projects/filezilla/ Status: CLNT http://ftptest.net on behalf of 112.135.26.115 Reply: 200 Don't care Status: USER saravana Reply: 331 Password required for saravana Status: PASS ********* Reply: 230 Logged on Status: SYST Reply: 215 UNIX emulated by FileZilla Status: FEAT Reply: 211-Features: Reply: MDTM Reply: REST STREAM Reply: SIZE Reply: MLST type*;size*;modify*; Reply: MLSD Reply: AUTH SSL Reply: AUTH TLS Reply: UTF8 Reply: CLNT Reply: MFMT Reply: 211 End Status: PWD Reply: 257 "/" is current directory. Status: Current path is / Status: TYPE I Reply: 200 Type set to I Status: PASV Reply: 227 Entering Passive Mode (112,135,26,115,43,9) Status: MLSD Reply: 150 Connection accepted Listing: type=dir;modify=20100322113235; it_is_working!_Andrejs_Cainikovs_from_serverfault.com Listing: type=file;modify=20100322110559;size=5; New Text Document.txt Reply: 226 Transfer OK Status: Success can anyone say why this happens to me? please im trying the whole day!!

  Read the article

• Linux Port 80 to redirect to a Windows box

  - by Richard Staehler

  I have 2 servers here at work. One is a Windows 2008 Server R2 (for safety's sake, lets use 192.168.1.100) and the other is a Fedora 14 (192.168.1.101). Currently when you hit our subdomain, x.test.com, our routers tell it to go to our Fedora box, and since Apache is installed and listening to port 80, it displays the Fedora Apache Test Page. It's obvious that I don't use port 80 for this machine, however I do use NAGIOS on it and its always nice to be able to access that from anywhere in the world. So when I want to access it, I just type x.test.com/nagios. Now here comes the dilemma.... On the Windows R2 box, we recently have installed a program that requires us to setup a web server using IIS7. Because of this application, I'm going to be creating a new subdomain called y.test.com, but since we only have 1 WAN/router, it will still get pointed to our Fedora box. That being said, it wants to use port 80 as well (or whatever port I damn well wish to assign it). So my question is: since our router is pointing to the Fedora 14 box (.101), and I want to make sure I can access NAGIOS from anywhere in the world, how do I tell Apache (httpd) to redirect port 80 to the other server (.100)? If not possible, what are my other options? I have rinetd installed on Fedora and have even tried the option 192.168.1.101 80 192.168.1.100 80 and it didn't seem to work "because port 80 was already bound" Thoughts? and Thanks!

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Hints on diagnosing performance issue in OpenBSD firewall

  - by Tom

  My OpenBSD 4.6 pf firewall has started having really bad performance in the past few weeks. I've isolated the firewall (as opposed to the WAN connection, switch, cable, etc.) as the problem, but need a hint on how to further diagnose or fix the problem. The facts: Normal setup is: DSL Modem - FW Ext. NIC - FW Int. NIC - Switch - Laptop Normal setup described above gives only 25 Kbps! Plugging the laptop straight from the DSL modem gives a 1 MBps connection (full speed, as advertised). Therefore, the DSL connection seems to be OK. Plugging the laptop directly into the firewall's internal NIC (bypassing the switch) also gives only 25 Kbps. Therefore, the switch does not seem to be a problem. I've replaced the ethernet cables, but it didn't help. Here's the weird thing. Reloading the ruleset (/sbin/pfctl -Fa -f /etc/pf.conf) causes the laptop's connection to go up to 1 Mbps (i.e. full speed) for a few minutes before it gradually degrades back down to 25Kbps again. Any ideas on what's wrong or how I could further diagnose the problem?

  Read the article

• Using two ports on my ZyXel USG gateway to patch two devices together?

  - by Matthew Beza

  I don't know if this is possible but it would save me many long drives! I have drawn, with my epic MS Paint skills, my current setup. I have a ZyXel USG300 Gateway with a built in 5 port switch. It supports bridging, tunnles, VLANs, etc.. I have a Cisco WLC2112 plugged into port 6 (P6). The cisco is set to 192.168.6.2 and P6 is set to 192.168.6.1. This works but I need to incorporate a Nomadix AG3000 to handle guests. (Router (A) in the picture). So I need the Cisco WLC2112 to use the Nomadix as if it where plugged into it's LAN port. Right now the Nomadix WAN Port is plugged into (P2) on the ZyXel, and the Nomadix LAN port is plugged into (P3). Is it possible to set something up where (P3) and (P6) are somehow "Patched" as if the Cisco was plugged directly into the Nomadix LAN port? Basically making the ZyXel a fancy Cat5e coupler?

  Read the article

• two computers on same network cannot ping eachother nor view NetBios resources

  - by slava

  I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

  Read the article

• PHP/MySQL Performance Testing with Just PHP

  - by Mike Gifford

  I'm trying to diagnose a server where the website is loading very slowly, but unfortunately my client has only provided me with FTP access. I've got FTP access so I can upload PHP scripts, but can't set up any other server side tools. I have access to phpMyAdmin, but not direct access to the MySQL server. It is also unfortunately a Windows server (and we've been a Linux shop for over a decade now). So, if I wan to evaluate MySQL & disk speed performance through PHP on a generic server, what is the best way to do this? There are already tools like: https://github.com/raphaelm/php-benchmark or https://github.com/InfinitySoft/php-benchmark But I'm surprised there isn't something that someone has already set up & configured to just run through and do some basic testing of a server's responsiveness. Every time we evaluate a new server environment it's handy to be able to compare it to an existing one quickly to see if there are any anomalies. I guess I'd just hoped that someone else had written up a script to do this already. I know I have, but that was before Github when there was a handy place to post scraps of code like this. Originally posted in http://stackoverflow.com/questions/12321498/php-mysql-performance-testing-with-just-php but it was recommended that I re-post it here.

  Read the article

• New AD-DC in a new Site is refusing cross-site IPv4 connections

  - by sysadmin1138

  We just added a new Server 2008 (sp2) Domain Controller in a new Site, our first such config. It's over a VPN gateway WAN (10Mbit). Unfortunately it is displaying a strange network symptom. Connections to the SMB ports (TCP/139 and TCP/445) are being actively refused... if the connection is coming in on pure IPv4. If the incoming connection is coming by way of the 6to4 tunnel those connections establish and work just fine. It isn't the Firewall, since this behavior can be replicated with the firewall turned off. Also, it's actually issuing RST packets to connection attempts; something that only happens with a Windows Firewall if there is a service behind a port and the service itself denies access. I doubt it's some firewall device on the wire, since the server this one replaced was running Samba and access to it from our main network functioned just fine. I'm thinking it might have something to do with the Subnet lists in AD Sites & Services, but I'm not sure. We haven't put any IPv6 addresses in there, just v4, and it's the v4 connections that are being denied. Unfortunately, I can't figure this out. We need to be able to talk to this DC from the main campus. Is there some kind of site-based SMB-level filtering going on? I can talk to the DC's on campus just fine, but that's over that v6 tunnel. I don't have access to a regular machine on that remote subnet, which limits my ability to test.

  Read the article

• Internet doesn't work when enable local network

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: Lan A) WAN interface (192.168.51.50) ( Used for internet) Lan B) LAN interface (192.168.30.228) ( used for local connectivity ) When I keep both LAN Enabled than my internet doesn't work, but if I disable my local LAN then internet works fine. How can I resolve this issue? Do I need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• what web based tool, to allow a non-technical user to manage authorized keys files on a Linux (fedora/centos/ubuntu/debian) server

  - by Tom H

  (Edit: clarification below) We have a number of groups of developers that change frequently, and a security policy to require individual logins to servers using rsa or dsa public keys, which is achieved via the standard method of adding id_dsa.pub to their authorized keys file. I am using chef to sync the user accounts across machines, however our previous method of using webmin to manage the user passwords is not designed for key based auth, and hence is not easy to use for non-technical users. The developers are logging in from the WAN using ssh, they can either provide their own key, or an administrator will send them a private key. The development machines are located in the cloud and we have a single server available to host the master set of accounts. Obviously I could deploy ldap or other centralised authentication system, but that seems a bit over blown when webmin worked well for the simple case. It is easy to achieve synchronised users, groups and passwords across a bunch of low security development boxes using webmin clustered users and groups. However looking at the currently installed webmin it is not so easy to create the authorized keys as it is to create user accounts and passwords. (its possible, but its not easy - some functionality is in the usermin module, or would required some tedious steps) Ideally I'd like a web interface that is pretty much dedicated to creating users and groups, and can generate key pairs on the fly, and can accepted pasted in public keys to add to the users authorized keys file. If the tool sync'ed the users and keys as well, that would be great, but I can use chef to do that part if the accounts are created correctly on the "master" server.

  Read the article

• VMWare Newbie - looking for hardware recommendations and help :) [closed]

  - by Dan

  I am looking for some hardware recommendations on an upcoming virtualization project. We are a small company (80 users - 25 in site 1, 55 in site 2) currently using Windows Server 2003 - no VM servers yet. Our AD is setup where site 1 is the root domain and site 2 is a subdomain/subnet - connected by T1 and VPN for failover. The current DC's also server as file servers, print servers, AntiVirus servers. Email is in the cloud. Additionally then in site 1 we have 3 additional member servers - one running IBM Websphere for a customer specific app, one running Infor PowerLink (no real heavy load) and another that we use for Virtual Studio apps and also runs DirSync for Exchange Online. No heavy workloads on any of these machines really. We also have an AS400 box that we run ERP/CRM software on that site 2 connects to over the WAN link. In site 2 we also have a SQL machine that runs on Win2K server. Database files are not large less than 5 GB. Light to Medium workload on this machine. File servers in each site store less than 500 GB data and probably won't grow to more than 1TB in the next 5 years. I am looking to go to VMWare in both sites and virtualize all servers. What recommendations do you have for server, storage hardware? Is it safe to virtualize all of your DC's? Any help or advice would be greatly appreciated. Thanks.

  Read the article

• SCM8014 to FVS338

  - by Jack

  I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Mac and L2TP VPN no problems, xp, vista and 7 no go :s

  - by The_cobra666

  Hi all, I've got some weird problem and I'm out off options. The situation: When connecting from my mac to the VPN server (Windows Server 2003 R2) with L2TP PSK, everything works like it should. However, when I connect from a Windows PC, nothing happens. it spits out error 809 and sometimes 789. Now I know that my ports are OK, since the mac can connect without any problems. It's the same for: XP, Vista SP2 and 7. None can connect. If I connect to the VPN server directly (to the internal IP instead of WAN from the router), it connect's without a problem. Connecting using PPTP works... now if only L2TP would work thank you very much Windows! I have checked the counters on my linux router with iptables -L -nv and they do not raise when connecting. Not on ACCEPT and not on DROP. Only when connecting from the mac. I've found the guide from Microsoft to enable: AssumeUDPEncapsulationContextOnSendRule in the registery. I have set it to "2", on the server and client. Still no go. After that registery key it started giving me error 789 instead of 809. The IPSEC services are running on the client and server. Is there anyone that ppleease can help me with this! I've been working on this for 2 days and I'm out of options. Thanks!

  Read the article

• Programmer configuring a new network

  - by David Lively

  I'm in the process of expanding my home network from a couple of laptops on a wireless Verizon FiOS router to include: Linksys 24-port switch Cisco Pix 515 Cisco 3640 router One new development desktop and three new machines to act as a db server, web server and a backup system. My company is moving offices and we've decommissioned some older hardware, which I was able to pick up for the cost of the labor to move it home from the office. The benefits to working with dedicated web and db servers are very valuable to me. I know very little about network topology, other than that everything plugs into the switch, which then plugs into the cheap Verizon router. (Verizon provides a coax connection that the router must translate into Ethernet before I can use it with any of this equipment). Questions: What is the recommended topology for this equipment? Verizon router - Pix - 3600 - switch? Is the 3600 even necessary or desirable? The Verizon router has one WAN port and 4 client ports, all 10/100. Is there any performance benefit at all to wiring multiple connections from the verizon router to the switch, assuming I don't use the Pix? Should I use the Pix? Software firewalls are a pain, and seem silly if I have a device like this lying around. Anything else I should know? Am I wasting my time with this? I also obtained a 7 foot rack, shelves, patch panels, UPS, patch panels, etc, which are going into a conveniently air conditioned closet. All constructive advice appreciated.

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >