Search Results

Search found 2481 results on 100 pages for 'hp'.

Page 26/100 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • Installing a new Motherboard in a HP xw6200 case

    - by thing2k
    I have a HP xw6200 Workstation, that is rather long in the tooth, and with 2 physical CPUs, it is quite inefficient. So, the plan was to upgrade the internals. Nothing special: AMD Athlon II X4 640 ASUS M4A78KT-M LE (mATX) 2x 2GB DDR3 1333MHz RAM. 3p under my £150 budget The issues: The pin connector for the front panel isn't a good fit, but I can trim it to size. The PSU has a 8-Pin Power connector, unsurprisingly, the new board has a 4 pin socket. The pins do line up, but I would have to cut it in half to fit. Finally, due to the weight of heat-sinks, they are screwed directly into the case. It turns out that these screws also lock the motherboard in place. As to remove it, you remove the heat-sinks, slide the motherboard across and lift it out. I tested the new board for fit, and while it slots in fine, it's not secure. There is nowhere to screw the board down, it is just held in place with plastic standoffs. The only idea I had, was to wedging something between the side of the motherboard and part of the case. Any suggestions?

    Read the article

  • Debian on HP ProLiant server hangs (disk i/o is my guess)

    - by Martin
    I installed Debian (2.6.32-5-amd64) on my HP ProLiant MicroServer (purchased recently.) I also added 3 2tb hd in zfs. I've experienced several server froze. Sometimes it showed Soft lockup CUP stuck for 61s! Today I experienced a different problem (I think) and the message looked like this [431336.200002] Call Trace: [431336.200002] [<ffffffff812fcc7c>] ? _write_lock+0xe/0xf [431336.200002] [<ffffffff810d7a86>] ? __vmalloc_node+0x99/0xe2 : : and (in different screen) [431354.222318] Node 0 DMA32 free: 2064kB min:5520kB low:69900kB high:8280kB active_anon:181648kB inactive_anon:61728kB active_file:313152kB inactive_file:832456kB unevictable: 0kB isolated(anon): 0kB isolated(file):0kB present:1922596kB mlocked:0kB dirty:72kB writeback:0kB mapped:25620kB shmem:344kB slab_reclaimable:34460kB slab_unreclaimable:31400kB kernel_stack:2288kB pagetables:7556kB unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no [431354.222431] lowmem_reserve[]: 0 0 0 0 : : Is this a hardware problem? What tools/methods can I find out the source of the problem? I've used Debian for years but never had problem like this.

    Read the article

  • Smart Array P400 - Accelerator Replacement Battery Failure

    - by inflammable
    TL;DR - Is the immediate failure of a replacement battery, for a failed battery, on a battery backed accelerator for a Smart Array P400 controller a common occurrence? Or are we likely to have an storage controller with an impending and critical fault? We have a slightly confusing situation with a Smart Array P400 storage controller with the 512mb battery backed accelerator addon on an HP DL380 server. The storage controller is (afaik) running the latest firmware and driver: Model: Smart Array P400 Controller Status: OK Firmware Version: 7.24 Serial Number: *snip* Rebuild Priority: Medium Expand Priority: Medium Number Of Ports: 2 The storage diagnostic (both on the both boot-up screen for the controller and within the 'Management Homepage' and the 'HP Array Diagnostic Utility') recently starting showing the following status a fault for the battery for the accelerator: Accelerator Status: Temporarily Disabled Error Code: Cache Disabled Low Batteries Serial Number: *snip* Total Memory: 524288 KB Read Cache: 25% Write Cache: 75% Battery Status: Failed Read Errors: 0 Write Errors: 0 We replaced the battery with a new unit (a visual inspection of the P400 card showing nothing unusual) and saw the same fault - but expected this to disappear over the course of a few hours/days as it charged. This didn't happy, and the fault status remains the same as above. Given the battery is a genuine part from HP, I wouldn't have expected a replacement battery to fail straight away, or to be dead-on-arrival (is that naivety on my part?). Is the immediate failure of a replacement battery, for a failed battery, on a battery backed accelerator a common occurrence? Or are we likely to have an storage controller with an impending and critical fault? Is there any diagnostic that could tell me more about the failed battery, without cracking the server open again? Many thanks!

    Read the article

  • I need scanning software to use with my scanner.

    - by D Connors
    So, I got this (HP F4280) printer/scanner about a year ago, and I'm really happy with it. The only thing is that I never really liked the HP scanning software that came with it. A few months ago I reformatted and reinstalled windows 7. Then, once I plugged in the printer, I noticed that windows recognized it automatically, and offered to install all the drivers by itself. So instead of manually installing the driver that came in the CD, I simply let windows automatically install it from its servers, and so far it's great. Instead of HP's scanning software (that really wasn't pleasing me), I got a very simplified interface that is more than enough for my ocasional scanning habits. Until today. Today I had to scan a bunch of old pictures for my father. And that simple interface felt like it was lacking quite a few features to make this repetitive task a little easier. And that's why I'm now looking for a good software to use for scanning. By "good" I mean anything well thought out, and specially anything that will make my life easier when repetitive-scanning. It doesn't need to have professional tweaking options, but having them is not a problem either. You guys got anything?

    Read the article

  • Having issue with OpenGL 1.0 for HP slate 7

    - by Roy Coder
    I have issue with HP slate when i am trying to draw Line in OpenGL Draw method. But working in other devices. In Hp Slate Green line not drawn properly as like in another device. My Code is: gl.glPushMatrix(); gl.glEnableClientState(GL10.GL_VERTEX_ARRAY); gl.glVertexPointer(2, GL10.GL_FLOAT, 0, vertexFloatBuffer); gl.glColorMask(true, true, true, true); gl.glDepthMask(true); gl.glLineWidth(8.0f); setColor(gl); gl.glDrawArrays(GL10.GL_LINES, 0, fPoints.length / 2); gl.glDisableClientState(GL10.GL_VERTEX_ARRAY); gl.glPopMatrix(); Suggest me at which place i am wrong or missing something? UpdateImage

    Read the article

  • WebCenter 11g (11.1.1.2) Certified with E-Business Suite Release 12

    - by Steven Chan
    Oracle WebCenter Suite is an integrated suite of products used to create social applications, enterprise portals, communities, composite applications, and Internet or intranet Web sites on a standards-based, service-oriented architecture (SOA).WebCenter 11g includes a multi-channel portal framework and a suite of horizontal Enterprise 2.0 applications which provide content, presence, and social networking capabilities.WebCenter 11g (11.1.1.2) is now certified with Oracle E-Business Suite Release 12.  For installation and configuration documentation, see:Using WebCenter 11.1.1 with Oracle E-Business Suite Release 12 (Note 1074345.1)

    Read the article

  • Portal 11g (11.1.1.2) Certified with E-Business Suite

    - by Steven Chan
    Oracle Portal 11g allows you to build, deploy, and manage enterprise portals running on Oracle WebLogic Server.  Oracle Portal 11g includes integration with Oracle WebCenter Services 11g and BPEL, support for open portlet standards JSR 168, WSRP 2.0, and JSR 301.Portal 11g (11.1.1.2) is now certified with Oracle E-Business Suite Release 11i and 12.If you're running a previous version of Portal, there are a number of certified and supported upgrade paths to Portal 11g (11.1.1.2):

    Read the article

  • Reassign the Right button functionality of touchpad

    - by Guandalino
    My notebook has a touchpad with two buttons. The touchpad works pretty well and I use it for vertical/horizontal scroll, two fingers scrolling etc. The Left button acts like the left button of a mouse. The Right button too, when clicked it makes appear the classic contextual menu (create new folder, move to trash etc...). The problem is that Right button doesn't work anymore for mechanical reasons, so pressing it has no effect. To recover the missing functionality, I'd like that pressing CTRL + Left button I get the same thing of pressing the Right button alone. Other combinations (CTRL + SHIFT + Left button) are also acceptable. Any way to do that?

    Read the article

  • 12.04 sound keeps auto-muting when idle

    - by fali
    I just installed 12.04 on an HP8510W. Everything works fine except for one weird behavior which I have noticed. When ever there is no audio playing, the audio mute indicator on the laptop is on. As soon as I start playing a you tube video the mute indicator turns off and I get sound. Here is my pulse audio output which says that the sink is suspended because it is idle: Welcome to PulseAudio! Use "help" for usage information. list-sinks 1 sink(s) available. index: 0 name: <alsa_output.pci-0000_00_1b.0.analog-stereo> driver: <module-alsa-card.c> flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE I tried running alsamixer, but I don't see the auto-mute option.

    Read the article

  • Ubuntu (i386 - 32bit) 12.04 LTS [DESKTOP] - Freezes During Preparing to Install

    - by Michael Ecklund
    I know this is for the Desktop version of Ubuntu, but I definitely plan on installing the server as well. I just want a GUI to manage my server. Here is what I have done: Placed Ubuntu i386/32bit 12.04 LTS [DESKTOP] disc in the disc tray. The disc loads fine. Clicked install Ubuntu. Without checking the download updates while installing or install this third-party software. Clicked continue. Mouse cursor turns to spinning circle and remains a spinning circle while the screen freezes its place at "Preparing to install Ubuntu". I tried not checking any of the boxes and clicking continue. I tried checking Download updates while installing. I tried checking Install this third-party software. I tried checking BOTH Download updates while installing AND Install this third-party software. Does anyone else face this very same issue? Is there a workaround for this problem? Do I need to use a lower version of Ubuntu? If so, which version do you recommend for my system specifications? My system meets the system requirements. Here are my exact system specifications. (Custom modifications: 320GBx2 HDD && 256MB AGP GFX card && 1GBx2 RAM)

    Read the article

  • Should I enable "Intel NIC DMA Channels"?

    - by javapowered
    I have HP DL360p Gen8 646902-xx1 I'm trying to optimize my config for low latency trading. Should I enable "Intel NIC DMA Channels"? Will that help/affect my system? From HP doc: Added a new ROM Based Setup Utility (RBSU) Advanced Performance Option menu that allows the user to enable Intel NIC DMA Channels (IOAT). This option is disabled by default. When enabled, certain networking devices may see an improvement in performance by utilizing Intel's DMA engine to offload network activity. Please consult documentation from the network adapter to determine if this feature is supported.

    Read the article

  • Proliant ML350 Won't Load Windows

    - by Mike
    I have a HP Proliant ML350 G4 running Windows 2003 Server Std Edition that will not load Windows on boot. It gave me a BSOD while running a recent Windows update and has not been able to boot since. The BSOD was a generic error, "Hardware Fault. Contact vendor." I am not getting any errors when the machine boots--it just hangs with a black screen when Windows starts to load. The machine will not boot into safe mode either--it gets stuck after beginning to load drivers. When trying to load the Windows recovery console I get the message that Windows cannot find any hard disks on the machine. This, despite having to load the driver for my storage controller. The HP Smart Start diagnostics finds no problems with my hard disks nor anything else. What should I try next? Mainly, I just want to be able to pull the data off my hard disks.

    Read the article

  • What happens when the USB key or SD card I've installed VMware ESXi on fails?

    - by ewwhite
    An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed. I encountered some rather ominous looking messages on the vCenter console and in the HP ProLiant ILO event log... Lost connectivity to the device ... backing the boot filesystem. As a result, host configuration changes will not be saved to persistent storage. Embedded Flash/SD-CARD: Error writing media 0, physical block 848880: Stack Exception. VMware advocates the use of USB and SD (SDHC) boot devices for ESXi. It was one of the main reasons the smaller footprint ESXi was developed (versus the older ESX). I've spent much time highlighting the differences between ESXi's installable and embedded modes to coworkers and clients. However, these failures do seem to happen. In this case, this is my third instance. Luckily, this is a vSphere cluster with SAN storage. What steps should be taken to remediate this failure?

    Read the article

  • Disable a Section of the Mousepad?

    - by Shahmeer Navid
    I purchased a hp envy 4 ultrabook. Its great but I'm infuriated at the touchpad. The click buttons and the touch pad are combined together but the click button area is touch sensitive. I usually rest my thumb on the right click but the mouse cursor goes completely crazy on this machine. Is there any way to disable a section of the touchpad? Basically make the click button area have nothing to do with the pointer function. I did see this post: Disable touch pad for mouse button region on new HP pavillion models? but the solution presented in that only limited the area from which the touchpad can begin. Since I rest my thumb on the click buttons, I would like to completely disable the click button area of the touchpad. Thank you.

    Read the article

  • VMWare - persistent "Host memory status" alarm in vSphere

    - by ewwhite
    I have a particular VMWare ESX 4.1 host that has a very persistent "Host memory status" alarm. This is running on an HP ProLiant DL360 G7 server. The HP ILO and System Management agents don't know any errors. If I clear the alarm in the vSphere client, it returns within a day. I've tried reseating DIMMs, however, the error does not indicate a problem with a specific module. There's another host in the cluster with an identical configuration. It's not exhibiting any issues. Any thoughts? This is touched on briefly on other forums (and here) with no clear resolution.

    Read the article

  • After installing Win7 on my laptop I'm having trouble extending the desktop to an external monitor

    - by devoured elysium
    I have a HP TX2000 laptop and a HP w2408 screen. Yesterday, I installed Win7 and I'm having trouble having the 24 inches screen work as a secondary screen. It seems like my laptop cannot detect both screens (its own and the 24 inches one). I think I already have all the drivers installed (I ran Win7's tool to detect and automatically update drivers and it said everything was up to date!), so what might be the problem? If I connect the 24 inch screen to my laptop, it will happily show a copy of what is being shown on that big screen too, but I'd like to have it ''extend'' the desktop to the big screen, instead.

    Read the article

  • Best Processor for MediaSmart Server?

    - by Kent Boogaart
    I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

    Read the article

  • Is proprietary vendor software required to use a wireless printer?

    - by sajee
    On Windows Vista, other than the driver, one can use a regular printer w/o any extra software, either plugged in via USB or over the network. I don't have to install extra software from the printer vendor to use the basic printer functionality. Is the same true for wireless printers? I need to install the HP 6000 wireless printer, and I hate installing vendor software other than the required drivers. So I'm wondering whether I need to install HP software on every PC that wants to use this printer? I haven't had a chance to read the manual but I'm hoping I don't have to. Can folks that have experience with wireless printers comment on whether vendor software, other than the printer driver, is required to use a wireless printer?

    Read the article

  • Admin mode on Procurve Switches

    - by stefan.at.wpf
    Not being a network expert, I spent some time configuring my network, until I found my mistake: On my HP ProCurve Switch 1810G, I thought that "Admin mode" means whether the administrative interface can be accessed from this port. Well, it means whether the port is enabled or not. Extract from the help function: Admin Mode - Select to enable the port-control administration state. Click to enable and have the port participate in the network.(Default : Enabled ) Well, of course I didn't read the help, because I didn't doubt it's for the adminsitrative interface and suspected an error somewhere else. Anyway, I am wondering if that is a commonly used term for enabling/disabling ports or if HP just wanted to make my life harder? I can't understand why this option isn't just called "Enable port"!? Here's a screenshot of how it looks in the web interface (yeah, shame on me for using a web interface)

    Read the article

  • Virtualization deployment for datacenter

    - by bogha
    Hi, my company is going to deploy an IT Infrastructure on a virtual platform, can you please help me with the following: 1- which one do you recommend, Cisco Unified computing system ( cisco + emc + vmware )or HP Blades( virtualization solution + HP Storage )? 2- i Need to install a DNS Server, Web server, cpanel for managing hosting packages and Microsoft layer of product for usingg in the corporate infrastructur ( active directory, Local DNS, Exchange server, DHCP, Global catalog ) what is the minimum requirments for these servers ( in terms of CPU and Memory ) . 3- what is the best way to implement a redundant solution in a virtual environment. thank you

    Read the article

  • Laptop hot after format

    - by Dany Khalife
    I recently formatted an HP G62 Laptop and installed all drivers from the HP site that should be installed for this model. But i noticed a very strange behavior, using Coretemp, the temp is always above 50 (on idle) and reaches 70 very quickly sometimes (Critical is 90) If i open youtube or skype alone, i can get temperatures as high as 83. Normally it was around 32 (on idle) and reaches 70 when i open games but not youtube.... I have a i3 processor and AMD graphics so i am wondering if somehow it's a graphics card issue (since i3 has integrated graphics as far as i know) Device manager shows only AMD graphics card tho, not sure if i3 graphics should appear here too. Any ideas what i might have forgotten to do after the format ?

    Read the article

  • Laptop hot after format

    - by Dany Khalife
    I recently formatted an HP G62 Laptop and installed all drivers from the HP site that should be installed for this model. But i noticed a very strange behavior, using Coretemp, the temp is always above 50 (on idle) and reaches 70 very quickly sometimes (Critical is 90) If i open youtube or skype alone, i can get temperatures as high as 83. Normally it was around 32 (on idle) and reaches 70 when i open games but not youtube.... I have a i3 processor and AMD graphics so i am wondering if somehow it's a graphics card issue (since i3 has integrated graphics as far as i know) Device manager shows only AMD graphics card tho, not sure if i3 graphics should appear here too. Any ideas what i might have forgotten to do after the format ?

    Read the article

  • Creating a vm using Hyper-V causes the host of BSOD

    - by Arcass
    Hi, Problem description: When I try to create a virtual machine, the host bsod part way through the process. From the logs in lookes to fail/hang on the "Creating new VirtualDisckDriver with new VHD" step. The BSOD error code is SYSTEM_SERVICE_EXCEPTION : STOP:0x0000003B When the machine has finished restarting, it looks to have created the vhd and XML files for the vm but it isn't accessable. I have two server bothing behaving in exactly the same way, so I don't believe it's a hardware fault. Has anyone had a similar experince? How did you resolve the problem? NOTES Hardware: HP DL380 G6 BIOS : 2010.03.30 (14 Apr 2010) [Latest from HP website] Inter Hyperthreading: Disabled Intel Virtuazation Technology : Enabled No-Execute Memory Protection: Enabled Mem check reports no errors OS: Windows 2008 Sp2 x64bit fully updated regards Arcass

    Read the article

  • data protector red tapes

    - by Caesar
    I am using HP Data Protector A.06.11 in my organization, with HP EML E-SeriesEML library, with 4 drives using LTO-4 tapes, and i am having some problems. Yesterday I put 5 new tapes in the robot and formatted them. At that time, the robot got just those empty 5 tapes with empty space. (all the rest of the tapes are red, or with protection) Today in the morning after the night (1 backup run at night), and 2 of the new tapes are red (the properties are): Writes : 2 Overwrites : 1 Errors : 9 I format one of them, and check for each drive if the tape become red, no one of the drives do it. In the main pool properties, in media condition got: Valid for : 36 (months) Maximum overwrites : 250

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >