Search Results

Search found 6445 results on 258 pages for 'indicator power'.

Page 26/258 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Computer wont start, just blinks on and off

  - by Ryan

  This is really strange. I had a comp that was working fine for over a year, then suddenly it started to shut off, it got so bad that I press the power button and in around 30 secs while booting windows it would shut off, then 20 secs... then 10 secs, then it refused to start all together. So I bought a new PSU (850w Thermaltake, the old one was 550w corsair) thinking that was the problem, I fitted the new PSU now and its the same thing, I press the power button and my fans start for a split second (they have led lights on them, so the lights come on) and then everything goes off again. I thought maybe it was my power button that was loose on my comp, luckily I had another chassis near by so I disconnected the powerSW from the old one and put ran the powerSW from the new chassis, press the power on the new chassis and same thing, it blinks for a split second and off again. Double checked connections from the PSU to the cpu power as well as board mobo power, its tight. It's pretty unlikely both the PSUs have the same exact problem so am lost... Suggestions?

  Read the article

• GRUB 2 freezing at OS selection screen, what could be the cause?

  - by Michael Kjörling

  Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

  Read the article

• Why is Flash power-hungry?

  - by Doug

  Apple historically argued that Flash was power-hungry, which made it inappropriate for use on mobile devices. I always thought that was just bluster excusing Apple's exclusion of Flash support from their mobile devices. But now I see that Adobe acknowledges that Flash is a pig. Why is it a pig? Are there bad programming approaches (that can be explained in layman's terms) that make it so power-hungry?

  Read the article

• Screen is greyed out after power failure shutdown: Mac OSX

  - by Don MacLachlan

  When the battery power is down and the unit not plugged in the computer is forced into a sleep mode requiring pushing the start button when power is re-connected. The initial desktop screen appears to be greyed out and is unresponsive with a timer bar which, when the timing sequence is complete restores an active desktop. I can't find any reference to this phenomenon in the OSX literature I have. Any pointers to where I can get more information? Perhaps I am using the wrong search criteria?

  Read the article

• Optimal brightness for laptop screen while on AC power

  - by Mehper C. Palavuzlar

  Does using the laptop screen at the maximum brightness level while on AC power have any disadvantages? May it decrease the lifespan of LCD screen, or convey more heat and cause more heating of laptop and battery? What should be the optimal brightness level while on AC power?

  Read the article

• Printing to Power point

  - by manojpcw

  Hi, Similar to the print to pdf option, where we can choose PDF to be the output format in the print dialog box when printing something from a browser or other applications, I am searching for something which can print to a Power Point file. Is there any such plugin or tool? Also link to a relilable print to pdf tool would be helpful. This essentially would eliminate the export to power point option that the users are asking for in my Silverlight application. Thanks...

  Read the article

• Journaled filesystems and power failure

  - by Yoga

  I heard that even a journaled filesystems such as EXT3/EXT4 might corrupted during power failure, e.g. from wikipedia [1]: In the event of a system crash or power failure, such file systems are quicker to bring back online and less likely to become corrupted. Can anyone provide more detail by giving examples such that when corruption can occur corruption is avoided by journaled filesystems [1] http://en.wikipedia.org/wiki/Journaling_file_system

  Read the article

• How can unity-panel-service be disabled?

  - by Amos Annoy

  From the unity-panel-service manpages: DESCRIPTION The unity-panel-service program is normally started automatically by the Unity shell (which gets started as a compiz module) and is used to draw panels which can then be used for the global menu, or to hold indicators. How can the unity-panel-service be non-automatically started abnormally? In other words, how is it arbitrarily manually started and/or stopped? The manpage implication is that this can be done without stopping the Unity shell. This answer seems promising: Is it possible to restart the unity panel without restarting compiz? but ... not. The process can be killed from System Monitor but it restarts automatically. references: How can menu bars that require a right click be activated like Ubuntu versions <10.10? How do I disable the global application menu?

  Read the article

• Can I blacklist an appindicator?

  - by d3vid

  I've whitelisted some indicators for apps that don't yet have Unity-compliant appindicators. Is there any way to blacklist appindicators for apps that are Unity-compliant (not old-style indicators) but don't provide a "Don't show in the system tray" option? Any solutions to ban an appindicator from being displayed, GUI- or CLI-based, are welcome. (I'm not looking for a way to just hide them like you can hide system tray icons in Windows.) (New-style appindicators can't be removed from the systray-whitelist.)

  Read the article

• How do I install sensors-applet?

  - by honestann

  I want to install sensors-applet onto my Ubuntu 12.04 computer. The instructions on this (and other) webpages says to enter this command in a command terminal: sudo apt-get install sensors-applet This is a gnome applet and gnome isn't exactly obscure. Why can sensors-applet package not be found? Before you say "no", note that I was able to execute "gnome-panel" to add a bar/panel along the bottom of my desktop, add 8 cpu-frequency applets to the bar (one per CPU core), and add gnome-panel to my startup applications. So I've already done the basics, and believe all I need now is to be able to download and install the sensors-applet to have that temperature applet available on the panel too. See here.

  Read the article

• How do I install the old sensors-applet package?

  - by honestann

  I want to install sensors-applet onto my Ubuntu 12.04 computer. The instructions on this (and other) webpages says to enter this command in a command terminal: sudo apt-get install sensors-applet This is a gnome applet and gnome isn't exactly obscure. Why can sensors-applet package not be found? Before you say "no", note that I was able to execute "gnome-panel" to add a bar/panel along the bottom of my desktop, add 8 cpu-frequency applets to the bar (one per CPU core), and add gnome-panel to my startup applications. So I've already done the basics, and believe all I need now is to be able to download and install the sensors-applet to have that temperature applet available on the panel too. See here.

  Read the article

• Are there plans to use the empty space in the SoundMenu?

  - by Kyle Clarke

  There seems to be roughly 4 lines of space next to the album art. However only 3 are used. Song Title Artist Album If nothing is planned for the 4th line. I propose that it is used for track time/length. This way you can tell how far along a song is without the need of a scrub bar. Unrelated, but I feel that the play-lists section should display how many songs are in that play list. Some of my play lists have no songs, and without realising this, it seems like a bug that the songs wont play.

  Read the article

• Upgrade to 12.04 results to empty Dash, no date & time either on the top panel

  - by Nicolas

  I've upgraded from Ubuntu netbook remix something to 12.04 LTS, and I've got two issues. (Got an Asus eeePc 32bits, Intel 945GME x86/MMX/SSE2 and Intel Atom CPU N270 @ 1.6Ghz x2) Nothing in the Dash. Only the "home" tab, other tabs are missing. No search results whatsoever. Missing elements in the system panel, privacy and date & time. No date & time on the right corner either. I've tried to reset unity with the terminal but the process was a whole mess full of errors. It did show date & time in the system panel (not on the top-right corner) while the process was going on in the terminal. But then it was such a mess (no more icons on the right corner amongst other things), and the process wouldn't complete, so I had to reboot the computer and get Unity as before, still no date & time and privacy.

  Read the article

• Disk mounter applet for Unity?

  - by sdaau

  Well - just because I cannot find this asked anywhere else on the net - is there something like a "Disk Mounter" applet for Unity interface, or are there any alternatives? (By 'alternatives' I mean: I wouldn't mind doubleclicking an icon, and have what used to be a toolbar applet start up as a separate window; as long as don't have to grapple with mount command lines, and filesystem arguments and such) Thanks, Cheers!

  Read the article

• 11.10 desktop alerts (volume change and terminal bell) stopped working but all other audio still works

  - by FlabbergastedPickle

  All, My sound works just fine in 11.10 64-bit install on HP dm1-4050 Sandy Bridge notebook (e.g. audio works in Banshee, flash, games, browser, Thunderbird email notification, etc.), but the core desktop notifications (e.g. pressing a tab in a terminal where there is more than one option should trigger a terminal bell, or changing volume using volume keys should be accompanied with the supporting "quack" that the volume app makes) do not work. I've intentionally disabled login sound as explained here on ask ubuntu but even enabling it back makes no difference. These notifications did work before just fine and I am not sure when did the actually stop working but it must've been fairly recently. Only things I did were trying to install some ppa edge xorg drivers for my intel card (a separate issue) but also reverted them all with ppa-purge once I discovered they did not improve anything. Other thing I did was check volume settings with alsamixer and did alsactl store for the soundcard after I did some experimenting with volume settings for PCM (on my laptop PCM at 100% crackles so I had to lower it and make pulseaudio ignore its setting as per ask ubuntu's page). That said, neither of these should have any bearing on the said notifications since the volume is up and they clearly work everywhere else but the core desktop events. The system ready drum sound when Ubuntu boots and user reaches the login screen also does not work. The guest login behaves exactly same as mine. Audio works (including the login sound since I've not disabled it for the guest account), but no quacks when changing the volume or terminal bell sounds... I've tried copying ubuntu sounds to /usr/share/sounds/ as suggested on ask ubuntu and that did not work. I also tried using dconf-editor to check sound theme settings and tried both freedesktop (which is what it was set to) and ubuntu, as suggested on ask ubuntu. This did not work either. I tried purging the ~/.pulse folder and the /tmp/*pulse* entries, rebooting and restarting pulseaudio with -D flag. While audio came back on and behaved just fine in all aspects (e.g. one can adjust volume levels, play music, games, in-browser sound stuff, and other app alerts) except for the system ready drum sound (at the login screen), and any system event (terminal bell and volume change quack sound). It is interesting that the quack sound works inside system settings-sound when adjusting levels there, but it does not when volume is changed via top bar's volume settings... I do recall that at one point yesterday when I was restarting pulseaudio the quacks that accompany volume change did start working but I have no idea what caused that. This was also when I first realized those alerts were not working. After rebooting it was again gone. I did compile my own 3.0.14-rt31 kernel a little while ago as instructed on one of the wiki's for the 11.10 rt kernel. Everything works as before except for the said sound alerts. I am not sure if this began happening since I started using the rt kernel though and yesterday's momentary ability to hear those quacks while changing the volume make me believe that the kernel is not one responsible for this problem. One more thing I can think of is that I used alsoft-conf tool to configure buffering on the OpenAL (due to TA Spring's choppy audio) and changed in there default audio device to ALSA. I also tried reverting it to Pulseaudio as the only allowed output but the bottom part of the Backend tab always reverts to ALSA even when I select Pulseaudio. The pulseaudio does remain as the only active choice on top. This, however, once again does not make any sense in terms of preventing desktop audio alerts when everything else including OpenAL games plays sound just fine... So, there you have it, as verbose as I could make it :-). I tried all I could find on this issue and had no luck so far... Any ideas?

  Read the article

• "Waiting for Sound System to respond." error dialog

  - by Paulo Truta

  Hello guys. I'm having a nasty problem with the Sound Menu on my Ubuntu 10.10 Installation. What happens is that the sound control icon is blocked, and i can't control the master volume. If i try to get to the Sound Preferences i get a little Pop-Up Window saying: "Waiting for Sound System to respond...". Don't know what to do... Apart of that, sound works great. Thanks a lot ;) PS: I made 2 screenshot uploads. Hope it helps.

  Read the article

• List of Appindicators

  - by user8592

  I installed Ubuntu 11.04 on one of my systems and I am using Unity interface. Unity is working quite nice so far but i really miss panel applets for net speed, cpu temp, and system monitor. These applets show useful quickinfo and unlike 10.10 there is no way to get these on panel or unity launcher. There are solutions like screenlets and conky but they don't feel appropriate for a clean desktop look. If you know then please list out any third party indicators with links so that they can be found at one place.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• How can menu bars that require a right click be activated?

  - by Amos Annoy

  I've noticed that NetworkManager only has a single, left or right, click menu and no longer has an About menu option to show it's splash screen. In fact all the top bar mini short cut icons have been amputated and crippled leaving them with no rights. This severely impacts on our custom aps., similar to FireFox bookmarks, which can no longer be right clicked to bring up a context menu. It is possible to disengage FF's File|Edit|... menu bar from the top by running it in safe-mode so the menu bar is resident in a window, restoring right clicks, but our aps. do not have "safe modes". How can right clicks in menu bars be restored? reference

  Read the article

• How to get average network load instead of instant

  - by Adam Ryczkowski

  Welcome, I use conky to see network load statistics with sampling every 8 seconds in order to get somewhat more smooth history chart. Unfortunately, all values i get are not average for this 8 second period, but they are sampled from much smaller time span, so charts are the same choppy, as if they were sampled from 1 second or less. Is there any way to get conky (or at least System Monitor) display system properties averaged over specified amount of time, just like Windows' task manager does? I would like to have conky display hard drive usage from iostat, but there will be little use if it, if conky reports instant values not averaged over time.

  Read the article

• Where are the systray icons for Dropbox in Ubuntu desktop 13.04 (minimal)?

  - by samvv

  I reinstalled Ubuntu desktop using the minimal CD image and the following command: $ sudo apt-get install ubuntu-desktop --no-install-recommends After that I used Ubuntu Software Center to make sure Unity supports application indicators: http://i.imgur.com/bYF162w.png. Everything works great, except for Dropbox. For some reason the icon doesn't appear in the tray, even though the application is running. Steam on the other hand runs just fine, so it seems like there is nothing wrong with the tray itself. According to this post the tray icons should be in /usr/shared/icons/hicolor/22x22/status but it doesn't contain any Dropbox icons. Neither do any of the other resolutions. The answer is a bit outdated, so I'm not entirely sure it is still applicable to the current version of Dropbox. I did the usual thing of reinstalling dropbox with: sudo apt-get purge nautilus-dropbox sudo apt-get install nautilus-dropbox But that didn't solve anything either. Does somebody know how to fix this issue?

  Read the article

• Notification / tray icon / applet drop downs disappear or flicker when clicked

  - by postfuturist

  For some reason, after upgrading to 11.10, the tray icon drop-down menus don't persist after a single click about 2/3 of the time. They always work if I click-and-hold, but I'm used to just clicking once to examine the menu. The behavior is not consistent, so the drop down menus will stay after click about 1 in 3 times. I'm running 64 bit Ubuntu on a dual-monitor setup. EDIT: from lspci: 01:00.0 VGA compatible controller: nVidia Corporation M116N (rev a2)

  Read the article

• How do I access and enable more icons to be in the system tray?

  - by Jon

  So I'm messing around with Natty a little, and I noticed that all the apps that would normally use the system tray (or "notification area"?) aren't displaying there. Is that a bug, or is that the way it's going to be? I heard something about Ubuntu getting rid of that feature entirely. Is there a way to add it back? I mean, I didn't really like it, either, especially when there were apps that used it unnecessarily, but I can't use CryptKeeper at all now, or easycrypt, and I don't know whether Dropbox has synced without opening Nautilus.

  Read the article

• How can menu bars that require a right click be activated like Ubuntu versions <10.10?

  - by Amos Annoy

  I've noticed that NetworkManager only has a single, left or right, click menu and no longer has an About menu option to show it's splash screen. In fact all the top bar mini short cut icons have been amputated and crippled leaving them with no rights. This severely impacts on our custom aps., similar to FireFox bookmarks, which can no longer be right clicked to bring up a context menu. It is possible to disengage FF's File|Edit|... menu bar from the top by running it in safe-mode so the menu bar is resident in a window, restoring right clicks, but our aps. do not have "safe modes". How can right clicks in menu bars be restored? reference

  Read the article

• Upgrade to 12.04, nothing in dash, no date&time

  - by Nicolas

  I've upgraded from ubuntu netbook remix something to 12.04 lts, and I've got two issues. (Got an Asus eeePc 32bits, Intel 945GME x86/MMX/SSE2 and Intel Atom CPU N270 @ 1.6Ghz x2) Nothing in the dash. Only the "home" tab, other tabs are missing. No search result whatsoever. Missing elements in the system panel, privacy and date&time. No date&time on the right corner either. I've tried to reset unity with the terminal but the process was a whole mess full of errors. It did show date&time in the system panel (not on the top-right corner) while the process was going on in the terminal. But then it was such a mess (no more icons on the right corner amongst other things), and the process wouldn't complete: so I had to reboot the computer and get unity as before, still no date&time and privacy. Thanks for any help. nic

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >