Search Results

Search found 8472 results on 339 pages for 'boot'.

Page 262/339 | < Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• Startup Disk Creator tool for Debian

  - by user61954

  I was trying to create a USB bootable in Debian to install my new system. I couldnt find any easy to use tool in Debian. I tried downloading the hybrid iso image from the Debian site and copied it to the USB using the dd command as said in Debian site. But it didnt boot. Next I used the Startup Disk Creator tool in Ubuntu and it worked like a charm. Is there any similar tool in Debian? I know that there is Unetbootin but its difficult to install

  Read the article

• How do I disable alert beeps

  - by wheresrhys

  My HP pavilion laptop is getting pretty old and the speakers no longer work properly. So I've disabled all audio devices, including disabling the light-touch volume controls at boot-up. The one sound still here that I can't get rid of is teh alert beep whenever there's an error. It's annoying at the best of times, but when your laptop has no other sounds at all it's intensly irritating! Nothing I change in the windows settings or in the BIOS seems to have any effect. Any ideas how to switch them off?

  Read the article

• How to set CHKDSK for drive C: in Windows 7

  - by prashanth

  I recently got a 0xc000007b error whenever I tried to run some application software. I found that CHKDSK for C drive might be a solution. When I tried to do it from C drive properties, it said the drive was in use and asked to schedule CHKDSK at the next reboot. I clicked OK. When I restart, I experience a BSOD. I waited for 10 minutes but still nothing happens. So I forced a shutdown (laptop) and again booted up the computer and got a BSOD for just 5 or 10 seconds and system boots and works with no problem. I repeated all these steps four or four times and yet with the same results. Is there any other way other than CHKDSK to solve the 0xc000007b error? If not, why is CHKDSK not working at boot up? Can I force CHKDSK on drive C: to perform while the system is on? Platform: Windows 7 64-bit.

  Read the article

• Win7 safe mode pretends it's Xp?

  - by Joachim Kerschbaumer

  hi there, just a question in between. a friend of mine brougth me a laptop that does not work anymore and wanted me to check whether i can do something. she told me its windows 7, and startup screen and login screen look like it. howevere, as she gets a bluescreen on startup it is only possible to boot in safe mode where the system pretends to be windows xp sp3. the system also may have 1 gig of ram but the system itself states that it has 954 mb of ram which is a value i´ve never seen before. is there everything corrupt from operating system to hardware, or am i just a newbie that does not know that windows 7 pretends to be winxp sp3 in safe mode? or is this laptop just the victim of an illegal, crazy copy of xp sold as win7? maybe some strange chinese stuff? i also recognized that the startup screen of Outlook Express is pronounced as "Outllok Express" (no typo) i´m kinda confused, maybe someone could put light into this ;) thanks

  Read the article

• Why can't windows see mmcblk0p3? [closed]

  - by jacknad

  The partition is created on the embedded linux target like this # n - new # p - partition # 3 - partition 3 # 66 - starting cylinder # <blank> - maximum size for the ending cylinder # t - set file system type # 3 - partition 3 # c - set to windows vfat # w - write partition table and exit echo -e "n\np\n3\n66\n\nt\n3\nc\nw" | fdisk /dev/mmcblk0 The file system is then formatted on the embedded linux target as MS-DOS like this # -n volume-name # -F FAT-size mkfs.vfat -n DB -F 32 /dev/mmcblk0p3 A linux host can mount and access files in mmcblk0p3 without issue. Why can't windows? Edit: Although the default number of FATS is 2 I tried adding -f 2 [number-of-FATs] since this is actually being done by busybox on an embedded platform but this didn't help. I understand the Linux MS-DOS file system does not support more than 2 FATs but there are only 2 on this target (the boot is also FAT which is visible), along with and EXT3 (on p2) for the root file system.

  Read the article

• diagnose "corrupt file" problems

  - by Matthew

  My computer has been crashing the last couple weeks pretty regularly (at least once a day). A lot of times things I do will display a little notification in the bottom right saying something about a corrupt file. (I'm on Windows XP Pro Service Pack 3). When the computer does crash I get the "blue screen of death" usually. Some of the notifications also advise running the chkdsk utility. I cannot get it to successfully run. Using the command prompt (or even the "tools" menu after right clicking the drive and choosing properties), it will not run the utility (it says "do you want to schedule it to run next boot time" or whatever, which I confirm). The problem is that most of the time after restarting, it doesn't run at all. The few times it does run, it has an error (I can't remember the error right now, it at least says it's ntfs and such) and says disk checking will end. How can I get it to successfully run?

  Read the article

• iMac invalid memory access and then crash?

  - by Sam McAfee

  My iMac G5 from a few years ago (the square white one) dies now, with a message about an invalid memory access. It goes straight to an Open Firmware prompt and doesn't even load the Mac OS at all. Am I correct in guessing that the memory is probably the issue, and that if I replace it, we may be able to boot again as normal? That's my gut feeling anyway, so I ordered some more memory and plan to swap it today. Any thoughts? Ideas?

  Read the article

• How do I disable aalert beeps

  - by wheresrhys

  My HP pavilion laptop is getting pretty old and the speakers no longer work properly. So I've disabled all audio devices, including disabling the light-touch volume controls at boot-up. The one sound still here that I can't get rid of is teh alert beep whenever there's an error. It's annoying at the best of times, but when your laptop has no other sounds at all it's intensly irritating! Nothing I chaneg in the windows settings or in the BIOS seems to have any effect. Any ideas how to switch them off?

  Read the article

• Can KVM CPU assignment count differ from physical hosts CPU count?

  - by javano

  I have read this question. I knew already that I could for example, have a quad core machine with four guests each having two vCPUs. As they don't all be require 100% CPU usage all the time, the scheduler would handle this for me. My question is about how this relates to a fail-over or migration situation; If host1 has two dual-core CPUs, and I assign guest1 four vCPUs (so it accessed all four physical cores), what will happen if I try and migrate it to host2 which only has one dual-core CPU? Can qemu-kvm emulate more vCPUs than there are physical? Or would I have to shut down the virtual machine, change the CPU assignment, migrate it, and then boot it back up (so no live migration)? Many thanks.

  Read the article

• Booting Linux from External HDD, with persistence

  - by Moriarty

  I am trying to install Linux, specifically Lubuntu or BackTrack 5 on an external HDD (Seagate FreeAgent GoFlex) but I have had no luck using YUMI, or Untebootin to get it working. I want the hard drive to be able to save the data within Linux (As in, If I install a program, it will stay there). I also tried doing this with a flash drive, which does boot, but it does not save data (I tried following Pendrive's tutorial on creating a casper-rw file and adding "persistent" to various files, but I cannot get it to save files. Basically, I just want a form of linux on a portable device that will save files and settings between boots Note: I do not have a CD to install from. Any help would be greatly appreciated, Thanks!

  Read the article

• Change Linux Console's Default Monitor

  - by Tim M

  Is there any way to specify which monitor the console is displayed on in Linux? Details: I have a 3 monitor setup with 2 video cards. When I boot the computer, the BIOS displays on the PCI graphics card (which has a small monitor). When starting Linux, the console is displayed on the same monitor. Is there a way to have the console output on a different monitor? I'm using the vesafb framebuffer. I don't see a way in my BIOS to change the default video card.

  Read the article

• Java application crashes my computer. How do I troubleshoot?

  - by Oded

  I am using NetBeans 4.1 for my university course (this is an older version, but is the required version for the course - I can't use a newer version). Whenever I use it for longer than several minutes, my computer crashes - it either reboots or I need to reset it. I have tried running with all startup items disabled (to rule out other applications interfering with the app), but it did no good. I have used Sysinternals procmon logging and the logs are corrupt - the only way I was able to get a good log was by enabling boot logging. However these are huge and I don't know what to look for. I am using Windows XP SP3, fully patched up and this is the only application that I have any kind of problem with. Can anyone suggest troubleshooting steps that will help me pinpoint the cause of these crashes and fix them?

  Read the article

• How can I install OpenSolaris without Graphical Environment - just text console?

  - by Sanoj

  I would like to install OpenSolaris and use it as a home-server. I will interact with it just with SSH, so I don't need the Graphical Environment. How can I install OpenSolaris without the Graphical Environment? And preferably I would like to use the SSH-interface as much as possible, is it even possible to do the installation over SSH? I tried the SSH-boot alternative on the installation-CD, then I have to use a password, but I have no password since I haven't installed the system yet.

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• Debian Harddrive Fdisk - Same ID's and changing letters

  - by James Willson

  I am trying to create and install a debain NAS and ive been having a hard time because I am new to all of this. I used ntfs-3g in order to automount my 4 NTFS drives. I also have a partitioned harddrive which is for the OS. When I was working on it and I ran this command I got this: fdisk -l /dev/sdae1 fdisk -l | grep NTFS /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 The weird thing is, all of the NTFS harddrives listed had an ID of 7. The next time I boot up my machine, I get an error about mounting /dev/sda1 and I run this command, and get the following results: fdisk -l | grep NTFS /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 I havent plugged in any drives, so whats going on? How to I make sure that my drives are mounted with the same sdXX name every time, and is the reason for this because they dont have unique ID numbers, if so, how do I solve this?

  Read the article

• Debian Harddrive Fdisk - Same ID's and changing letters

  - by James Willson

  I am trying to create and install a debain NAS and ive been having a hard time because I am new to all of this. I used ntfs-3g in order to automount my 4 NTFS drives. I also have a partitioned harddrive which is for the OS. When I was working on it and I ran this command I got this: fdisk -l /dev/sdae1 fdisk -l | grep NTFS /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 The weird thing is, all of the NTFS harddrives listed had an ID of 7. The next time I boot up my machine, I get an error about mounting /dev/sda1 and I run this command, and get the following results: fdisk -l | grep NTFS /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 I havent plugged in any drives, so whats going on? How to I make sure that my drives are mounted with the same sdXX name every time, and is the reason for this because they dont have unique ID numbers, if so, how do I solve this?

  Read the article

• Windows 7 safe mode pretends it's Windows XP?

  - by Joachim Kerschbaumer

  Just a question in between. A friend of mine brought me a laptop that does not work anymore and wanted me to check whether I can do something. She told me it's Windows 7, and startup screen and login screen look like it. However, as she gets a bluescreen on startup it is only possible to boot in safe mode where the system pretends to be Windows XP SP3. The system also may have 1 GB of RAM but the system itself states that it has 954 MB of RAM which is a value I've never seen before. Is everything corrupt from operating system to hardware, or am I just a newbie that does not know that Windows 7 pretends to be Windows XP SP3 in safe mode? Or is this laptop just the victim of an illegal, crazy copy of Windows XP sold as Windows 7? Maybe some strange Chinese stuff? I also recognized that the startup screen of Outlook Express reads "Outllok Express" (no typo) I´m kind of confused, maybe someone could put light into this ;)

  Read the article

• Hypertransport sync flood error

  - by Carl B

  What is it? And what causes it? Is it only for uncorrectable DIMM Errors(Troubleshooting DIMM errors)? When an UCE occurs, the memory controller causes an immediate reboot of the system. During reboot, the BIOS checks the Machine Check registers and determines that the previous reboot was due to an UCE, then reports this in POST after the memtest stage: A Hypertransport Sync Flood occurred on last boot 3 BIOS reports this event in the service processor’s system event log (SEL) as shown in the sample IPMItool output There are what seems to be some suggested answers to include Bad Caps Bios verisons (happens in one version not the other) Graphics card issues Lack of power to the CPU The list of possible generators seems to target everything but the computer case. System Specs: Windows Home Premium 64 Motherboard - MSI790FX-GD70 (MS7577) / Bios v 1.9 (American Megatrensa Inc) Ram - Patriot G Series ‘Sector 5’ Edition 4GB DDR3 1600 CPU - AMD Phenom II X2 555 Black Edition Callisto 3.2GHz Socket AM3 80W (Note: unlocked 2 cores CPU Z ids it as phenom II x4 B55) Graphics - 2 x Radeon 5750 in crossfire PSU - ABS 900w HDDs - 2 Seagate 1.5 TB Sata SSD - 1 OCZ 120 GB Vertex Plus R2

  Read the article

• Dell poweredge 1850's - wont install os

  - by user1326789

  I have 3 of these dell 1850 rack servers. 1 has 3GB RAM and 2 73GB HDD's. 2 have 6GB RAM and each of them has 2 73GB HDD's. I am currently trying to install an os on them but when i boot with windows xp setup, it gives me an error saying no partition found. Now i have set these drives up in RAID on the server and i put them "online" so it should be working fine but they're not. Please assist me in installing an operating system on these, i have no clue as to if it's the BIOS or the RAID controller within it. Thanks in advance, -Matt.

  Read the article

• Installing Linux kernel 2.6.25.14 on RHEL 5.4

  - by aaron

  I have to install Linux kernel version 2.5.25.14 on a RHEL 5.4 server because of drive compatibility issues. I follow the RedHat "Building a Custom Kernel" instructions running the following: $ make mrproper $ make xconfig $ make clean $ make bzImage $ make modules $ make modules_install $ make install But I get a bunch of warnings like this: WARNING: No module ehci-hcd found for kernel 2.6.25.24, continuing anyway When I try to boot this kernel it is unable to mount the hard drive, and kernel panics on startup. As far as I can tell I'm using a standard configuration (I just accept the defaults and save a .config file). Is there something I'm missing? Thanks.

  Read the article

• Laptop monitor goes black under intense graphics

  - by drahcir

  I have a dell inspiron 1520 with a nvidia GeForce 8600M GT video card. I have Windows 7 professional as an operating system. Yesterday when I was using it the screen started to somewhat flicker then go completely black. I restarted it and in the boot screen everything seems fine, when I entered the login screen it became flickery again, and when I logged in, when a couple of windows popped up it went black again. I hooked it up to a tft monitor and the monitor works fine, and did some more tests that confirmed that under higher graphics causes the laptop monitor to go black. Is there a reason why this is happening?

  Read the article

• How to get Windows Server 2008 VM to use multiple cores

  - by David Fraser

  I have a Windows Server 2008 machine running in VirtualBox. On initial installation, only one processor was made available, but now I want to run it as a multiprocessor machine. I have made all four cores available in the VirtualBox settings (as well as enabling VT-x/AMD-V and Nested Paging), but Task Manager still only shows one CPU. However, the four CPU cores are visible in Device Manager under Processors. In the event log on startup, I can see the following relevant events: EventLog.6009 Microsoft (R) Windows (R) 6.00.6002 Service Pack 2 Multiprocessor Free Kernel-Processor-Power.4 Processor 0 exposes the following: 1 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) Kernel-Processor-Power.4 Processor 255 exposes the following: 0 idle state(s), 0 performance state(s), 0 throttle state(s) How can I make this system actually boot up as a multiprocessor machine?

  Read the article

• HALEVT troubleshooting: VFAT usb storage device gets mounted with root:root user:group

  - by Nova deViator

  Hi, i'm banging my head for number of days around this problem. using Halevt for automounting, everything mostly works, but the only thing is that Halevt mounts external USB storage devices as root. So, as user i cannot write to files on them. Halevt gets run as halevt user on boot through /etc/init.d script. This is Ubuntu Lucid with Awesome WM. No GDM. Running halevt as user seem to not work (halevt runs but doesn't respond on Insert) I know HAL is deprecated and removed and i should probably write my own UDEV rules, but until then it seems there must a be simple hack that enables mounting VFAT/NTFS devices with specific uid/gid. this question/answer helps a lot, but not specifically to the above.

  Read the article

• Blue Screen at booting Windows 2000 virtual

  - by darkdog

  well i hope this stackexchange site is the right for my issue. I've an Oracle VirtualBox running on some acer pc Settings for the Acer PC: Windows 7 SP1 64bit Intel G630 @ 2.7Ghz 2GB RAM i used a .vhd image which contains a windows 2000 system with some preconfigured stuff and software for a customer. At the Windows boot time immediately after the "Loading Windows 2000..." - Screen i get the following Error: Sorry for the German Text but it say's something like "Check the Size of your HDD. If the error contains a driver, deactivate it and try again. Or change the graficcard" The HDD Size shouldn't be a problem in my honest opinion. Can anyone give me an adivce what i can try to do? I just tested the same combination of the .vhd image and oracle virtualbox on another computer. Same issue. Greetings

  Read the article

< Previous Page | 258 259 260 261 262 263 264 265 266 267 268 269  | Next Page >