Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 266/286 | < Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >

  • Two DHCP interfaces asigned to two default gateways to OS

    - by user140600
    I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

    Read the article

  • C# sends SQL data 4 times less from one box than from another

    - by Bobb
    W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

    Read the article

  • Ubuntu network card problem.

    - by Steve Greene
    Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

    Read the article

  • Windows 7 ICS client web failure

    - by n8wrl
    I have several windows 7 PC's connected on a LAN via a hub. One has a Verizon 3G connection and works great. I have internet connection sharing enabled on it, which automagically set the LAN connection to 192.168.137.1 and enabled DHCP. I am trying to get the client PC's working one at a time. The others are off. The client is able to: Get an IP via DHCP with correct settings. Ping any web address I can throw at it, so DNS and routing are working. Windows update works. But web sites hang in IE. All but google.com! I type www.msn.com, microsoft.com, amazon.com, etc. etc. All ping via a cmd window but IE just hangs - it says web site found but the green progress bar just slowly creeps and no content displays. www.google.com comes up even after clearing browser and dns cache. I am pulling my hair out - what am I missing? EDIT: After some more gyrations with a router I'm back to ICS. Same symptoms, only now I have an answer to Andrew's question, YES I can do Google searches but clicking on any of the result links hangs! Let one sit for half an hour with no timeout or error.

    Read the article

  • dhcp3-server (dhcpd) is tampering with host NIC

    - by user61000
    Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

    Read the article

  • ipv6 with KVM on debian

    - by Eliasdx
    I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

    Read the article

  • Sparc Solaris 2.6 will not boot

    - by joshxdr
    I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

    Read the article

  • How to configure a large mtu (linux)

    - by Somejan
    I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

    Read the article

  • why Thinkpad T410s intermittent keyboard death?

    - by patrickmdnet
    I have a Thinkpad T410s running Windows 7 64-bit. I have had it for three months. It has the latest BIOS (1.41) and trackpad drivers. In the last week I have started to notice that the keyboard intermittently stops working. Specifically, keystrokes have no effect, including Fn-F12 (shutdown) and Ctrl-Alt-Del. The LED on the capslock key does not turn on or off. Whatever state the lighted keys (e.g. mute) were in remains. The trackpad and trackpoint work properly, and I can close apps and properly shut down the machine. When I attach a USB keyboard it is recognized, but no keys work. If I run the Lenovo keyboard test, all the keys register properly and the caps lock light works again. When I quit the test app, the caps lock light stops working. If I hit Fn-F12 while the keyboard test is running, it goes into hibernation. When the machine comes back from hibernation, once I exit the keyboard test I again cannot do any input on the keyboard. I'm pretty convinced there is a software or driver problem. I never saw this the first three months I had the laptop. I do not recall installing anything recently. I am sure I've received some Windows security updates. I tried using wired networking instead of wireless - no difference. There doesn't appear to be any inciting event; it usually happens when I am working over ssh. I switched from rxvt+ssh to Putty and the problem still occurs. Any ideas?

    Read the article

  • Trouble in Team Viewer VPN Connection

    - by Sumit Pal
    I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

    Read the article

  • Route return traffic to correct gateway depending on service

    - by Marnix van Valen
    On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

    Read the article

  • How to prevent asymmetric routing with multiple eBGP routers?

    - by Andy Shinn
    I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

    Read the article

  • Using Different Networks with Different Proxy Servers on Windows 7

    - by John
    Hi, I have a laptop running Windows 7 Professional. There are two wireless networks I connect to every day: Home: no proxy server Work: proxy server with authentication On my iPad and iPhone, I've got two WiFi network profiles (one for home, one for work). The work one has the proxy server settings specified. The home one has no proxy specified. It all works great and I don't need to go changing settings around whenever I move from home to work or vice versa. On my laptop, however, I can't seem to get this going. I can certainly connect to both networks, but when I'm at work I have to go and change the proxy settings (in Internet Options) to be able to use the network. When I'm at home, I have to then go and turn them off. It's a small thing, but considering this is something I have to do every day, it's a bit annoying. Is there any way I can make Windows automatically switch proxy settings on or off based on the network I'm connected to? Thanks, John

    Read the article

  • Known USB 2.0 devices don't install driver, but must be manually forced

    - by Darragh
    When a known USB 2.0 device is plugged in and detected, it doesn't install the driver correctly but shows a Code 28 error and lists the device under "Other Devices" in Device Manager. When view properties of this device , it shows the following status; The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver. When updating the driver manually and selecting the appropriate driver Windows doesn't believes it's the correct driver, but you can force the installation and it works! The other condition the driver will auto-install is when the same USB device is plugged into a USB 3.0 port. Power related issues are not also causing this as I have tried vi a Docking station, USB hub. etc.. Devices tried; Jabra Headset USB-Mass Storage Device (flash disk and ext HD) MS Wireless Keyboard & Mouse USB Ethernet controller (USB-MAC controller) This is on a laptop part of a Domain with Windows 7 Ent 7601, I am logged in as a local administrator. There isn't any Group Policies blocking not signed driver or whitelisted devices on the domain. Any suggestions please feel free

    Read the article

  • Network Security Device/Software

    - by Campo
    We currently run Symantec Antivirus Corporate 10.2. The software is really easy to manage on a network but the actual virus detection isn't bad but the malware detection is crap. We recently were infected with a email bot that got us put on some block lists. This has been resolved. I cannot have that happen again. I would like to find a program as easy to manage as symantec that I can install on all the user's workstations as well as the servers. We run a windows 2003 domain. We have a couple 2008 test servers in the environment. Most of the workstations are xp though I am using windows 7 and symantect is not compatible with this OS... So we need a solution that would cover all those operating systems. If it could be installed on macs too that would be a bonus though not necessary at all. This software must detect: Viruses AND Malware I am looking for something that combines the features in anti-malware programs like malwarebytes or spybot with an antivirus program like symantec or AVG. Alternatively if there is a piece of hardware that is a firewall, router, and packet inspection for virus/spam that would be the most ideal solution. I then could supplement with a piece of software that could pickup what the hardware misses. Thank you for your suggestions.

    Read the article

  • Windows 7 remote desktop encryption error every few minutes

    - by rfrankel
    Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

    Read the article

  • Strange network connectivity problem

    - by Marc
    Here is my network connectivity: cable modem | |(WAN) wrt54g (default gateway, 192.168.1.1) -- earth |(LAN) | Simple Switch1 | | | | | SimpleSwitch2- neptune | | | | mars mercury | |- venus | |- laptop | saturn (Windows AD DC) simpleSwitch2 was hanging off the wrt54g. I moved it to SW1 during troubleshooting. Nothing described below was any different. earth is connected via wireless to the wrt54g. I can ping from laptop to mars, neptune & mercury. I can ping from earth to venus, saturn & laptop. However, pinging mars, mercury or neptune from earth gives the following result. Pinging mars.XXX.XXX [192.168.1.105] with 32 bytes of data: Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Ping statistics for 192.168.1.105: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), .122 is the address of the machine from which I am pinging. earth is a Vista machine. Windows firewall is off. saturn is my DNS & DHCP server. Can anyone give me any ideas what the h*ll is going on? Clearly the topology is a factor And yes, I am a space geek.

    Read the article

  • Access server using IP on another interface

    - by Markos
    I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

    Read the article

  • "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

    - by salparadise
    I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

    Read the article

  • HP Laptop recognizes hard drive just long enough to install windows

    - by Joe
    I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

    Read the article

  • DNS lookup fails when with all the MAC workstations

    - by user39564
    Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

    Read the article

  • Track kids browsing history even when they know how to clear it manually

    - by Darren Newton
    I have a colleague with two teenage boys (yes, cue cliche's about 'I have this friend see...') He's currently having issues with them browsing pr0n and wants to do a little spying on their browsing (I'm staying clear of the philosophies/ethics on this.) The kids are savvy enough to clear their browsing history when they're done. As I'm his goto for IT he has asked me if there is a way to keep a hold of the browsing history. The family uses Macs, and the kids surf with Safari. I know that browsing history is kept here ~/Library/Safari/History.plist. I figure there should be a way to write either an AppleScript or other script (Python/Ruby/Bash) that can backup this file to a different location (/opt/local/history, etc.) Since the kids know to clear their history when they're done should the file be periodically backed up with something similar to a cron job or something like Hazel? While that could work it seems like it would create a ton of little incremental backups. Or is it possible to 'watch' ~/Library/Safari/History.plist and incrementally add changes to a backup file (saving a diff so to speak) but not lose any data? Any ideas/solutions appreciated. UPDATE/EDIT: Got the word from concerned dad that the oldest uses Firefox on a different PC, so the OpenDNS solution (preferably at the router level) is the best answer so far as it would capture usage for the whole house.

    Read the article

  • Setting Remote Desktop to allows IPv6 connections

    - by Garrett
    Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

    Read the article

  • Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

    - by tednewk
    I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

    Read the article

  • which vista services can be disabled with impunity?

    - by GwenKillerby
    I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. I've looked at the other questions but they didn't answer me. thanks, Gwen.

    Read the article

< Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >