Search Results

Search found 18860 results on 755 pages for 'enigma machine'.

Page 268/755 | < Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275  | Next Page >

• Figuring out which PC part is faulty

  - by Davy8

  I have an odd scenario and I'm having trouble figuring out which is the faulty component. First of all, the video doesn't work, monitor says it's not getting a signal. Monitor's not faulty (works on other computer) so the first suspect was video card. However 2 things make me think it's not the video card. (Don't have another machine with PCIe around to test definitively) First, the GPU fan is spinning so it's getting power. Second, tried putting in an older PCI video card that is known to be working (pulled out of another working machine) and there's still no video. Normally if it's not the video card I'd suspect the motherboard, but everything's getting power on the mobo, so I'm not sure. The case apparently doesn't have system speakers, so can't hear any of the diagnostic beeps either. Also not sure whether a faulty CPU would cause no image at all either. The parts are brand new so something's going to get RMA'd but I'm not sure which component is to blame in this case. (Only slightly related, but I also accidentally put too much thermal paste on the CPU. The fan/heatsink instructions said to put the whole tube which seemed like a lot compared to previous experience, and as I started squeezing I knew it was definitely too much and stopped at about 1/3 but against my better judgement I didn't wipe any off. I'm not sure whether that would cause problems other than not cooling as effectively as it should)

  Read the article

• SQL - an error occurred during the pre-login handshake

  - by Rivka

  Until yesterday evening, I was able to connect to my server from my local machine. Now, I get the following error: A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The wait operation timed out.) (.Net SqlClient Data Provider) Note, I can log on to the actual server with no problem. Yesterday, I installed IIS on my machine and set up a site using my IP address - don't know if this has anything to do. I did come across this article, followed the steps, but didn't seem to help. http://www.escapekeys.com/blog/index.cfm/2011/1/26/Microsoft-SQL-Server-Error-64-A-connection-was-successfully-established-with-the-server I also went through the following article, changed TC/IP settings, restarted, but nothing. http://blog.sqlauthority.com/2009/05/21/sql-server-fix-error-provider-named-pipes-provider-error-40-could-not-open-a-connection-to-sql-server-microsoft-sql-server-error/ Started trying suggestions from comments too but stopped when I realized I might be messing things up more. So, why is this happening / how can I fix?

  Read the article

• Uninstall Glassfish and metro completely

  - by user775829

  I thought of updating my Glassfish server from 2.1 to 3.1.1 in a Linux machine. I downloaded the .ZIP package. However during uninstalling of Glassfish v2.1 I did not find the uninstall.sh file in "bin" directory. Following are a few steps which I did... I removed the glassfish folder (rm -rf ...) After removing files in the end it gave me a notification that it could not remove 2 files used by Metro. I cant recollect those file names, but I manually deleted that folder. I made a mistake by first not uninstalling Metro. I uninstalled metro completely after that. but it seemed pointless (it uninstalled successfully :P ) I transfered the Glassfish 3.1.1 ZIP file and unzipped and configured it. FOllow are a few Problems I am facing I cannot deploy any of my WAR file. Its giving errors saying " Error creating bean,Instantiation of bean failed etc etc." (However the WAR file is getting deployed successfully in other Linux Machine) When I try installing Metro v2.1 separately, it does not show the admin console or it timesout while starting the domain. The Log File of the Domain says it has started the domain successfully and the process is also created. But after running the command (asadmin) it takes like forever and times out without showing Domain Started Successfully, There is no uninstall.sh in Glassfishv3.1.1 bin directory. How do I completely uninstall Glassfish v 3.1.1 and Metro 2.1 ??? What are the files which I will have to manually remove?

  Read the article

• Rails 3 + Nginx + Passenger -- Routing index

  - by Bijan

  I have no index.html file in my public folder. My rails routes file routes this, and it works fine when I run 'rails server' on my machine. I'm trying to deploy the app. I have passenger and nginx running When I run rails server on my local machine, it works fine. But it's just trying to access static file when I try to access it on the production server. Here's my nginx conf: worker_processes 1; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.9.1/gems/passenger-3.0.2; passenger_ruby /usr/bin/ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { listen 80; server_name mmjconsult.com; root /www/mmjs/public; access_log logs/host.access.log; passenger_enabled on; } } Thank you for any help. I really appreciate it.

  Read the article

• Physical Debian to VMWare: vmware-converter, dd-image or otherwise?

  - by Dabu

  we have two debian Lenny production machines, both running larger commercial websites. Now these machines need to be moved, and in the process, they need to be virtualized to VMWare ESX. If you believe the internet information, there are several ways to accomplish this. The easiest for us would be to use our weekly dd backup where the whole disk, however, I have no experience with this kind of technology and if it is really possible. The second best way would be via an application on the source machine virtualizing it and generating an ESX compatible VM. However, the software is beta and unsupported, and after installation, nothing really works (the /etc/init.d/vmware-converter script doesn't actually do anything, start and stop reply with success messages, yet ps shows that there are no new processes). The worst way with the most work would be to install a new machine and set it up manually, copying files and databases as needed. This part is clear in it's execution, and my question(s) do not touch this. Is my 1st way possible? Has anyone done this yet, or better, has a page with instructions? Or is there a help page that explains how to correctly install, run and use the vmware-converter tool using a Debian installation (it's possible that I dod something wrong during installation already)? Thank you.

  Read the article

• when to upgrade server to include more cores, versus more processors, versus additional server?

  - by gkdsp

  The server hosting market is separated into single, double, qual, etc., processors, where each processor has several cores, or CPUs. My company will offer a Linux-based web application that relies on an Apache web server and a middle tier for business logic. The middle tier is used to crunch math, and return result to a client. Many clients may access the application simultaneously. The company will start with one processor having 4 cores. I'm trying to understand how the app uses the cores and then how to scale the application as business grows, in terms of servers/processors/cores. For example, I'd assume initially one core would be used for Apache, and the other 3 used to process client's requests for math crunching... Question 1: does that mean, with the 3 cores available, I can handle 3 separate client requests simultaneously (e.g. 1 for each of 3 cores)? I mean, except for the shared RAM, is this effectively like having 3 individual machines (from pt of view or processing client requests simulaneously)? Or, only one client's request may be processed at any one time, but that client's request is divided up into up to 3 cores depending on the type of process running that does the math crunching and whether or not it can take advantage of multi threading (so the # of cores impacts how fast any one client request completes)? I'm confused about what the cores mean to the application here. Question 2: As the business grows and more client requests need to be processed, should the server be upgraded to (A) a new machine with more cores, (B) a new machine with two processors, 4 cores each, or (C) keep the original server and add another server with a single processor? Which route provides the most efficient way to scale the application, in terms of processing more client requests per time interval? Is the choice, for example, limited by RAM (when you need more RAM than box can handle it's time to add another server), or something else? Question 3: Is the total number of client requests processed simultaneously equal to the number of cores times the number of servers (minus the one core for Apache)?

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• Mounting fuse sshfs fails when invoked by Cron on FreeBSD 9.0

  - by Tal

  I have a remote server filesystem that I'm attempting to mount locally on a FreeBSD 9 machine via FUSE sshfs, and Cron for a backup routine. I have ssh keys between the boxes setup to allow for passwordless login as the root user on the local machine. Cron is set to run the following script (in Root's crontab): #!/bin/sh echo "Mounting Share" /usr/local/bin/sshfs -C -o reconnect -o idmap=user -o workaround=all <remote user>@<remote domain>.com: /mnt/remote_server As root, I can run this script on the command line without issue, and without being asked for a password the share mounts successfully. Yet, when run by Cron the script fails. The path to sshfs is identical to the value of which sshfs Here is the email root receives from the Cron Daemon: X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <HOME=/root> X-Cron-Env: <PATH=/usr/bin:/bin> X-Cron-Env: <LOGNAME=root> X-Cron-Env: <USER=root> Mounting Share fuse: failed to exec mount program: No such file or directory fuse: failed to mount file system: No such file or directory I'm stumped as to why I'm receiving No such file or directory in this instance. It further seems odd given that the paths appear to be correct. I've also attempted to compare the output of env on the shell with env inserted into the script. I don't see any environment variables that should cause this trouble. At bootup, FUSE reports its version as: fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8 Help me ServerFault wizards, you're my only hope!

  Read the article

• Can Dovecot IMAP automatically create Maildir folders for new (virtual) users?

  - by user233441

  everyone. I am learning to set up a dovecot home IMAP server using a virtual Ubuntu 12.04 machine. My intention is eventually to have a home server that uses POP3 to take email from several addresses and remove them from my ISP's servers, while making them accessible through a home IMAP server (this is similar to the setup described at https://help.ubuntu.com/community/POP3Aggregator, which explains how to set up the system with dovecot version 1, and is thus outdated). I intend to use the ISP's server directly when sending messages, and to BCC all sent messages to myself. I've completed the basic set up of the test server: getmail uses POP3 to fetch messages from two test email accounts, and successfully delivers them to the respective Maildir-style new folders on the virtual machine. Dovecot then successfully sees these messages. I have two questions: 1) I had to set up new, cur, and tmp folders for both of the test accounts manually to get this setup to work. Is there a way to get dovecot to create these Maildir folders automatically when I create a new virtual user account (e.g., when I add a user and password combination to my dovecot password file), or is it expected that I write a bash script to automate that task? 2) I would welcome any comments you have on how this approach could be improved as I learn to set it up. My motivations with this approach are 1) to enable archiving/storing emails from several hosting providers that impose a cap on server storage, and 2) to give me somewhat greater control over email storage without requiring that I set up and administrate a mail server from scratch (which I'm not yet prepared to do) (this follows the recommendations at https://ssd.eff.org/tech/email). Thank you!

  Read the article

• Ubuntu inside VirtualBox is slow

  - by Kapsh

  I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

  Read the article

• Audio server with best API?

  - by Wintermute

  I'm a web dev, working in a small studio with a couple of other devs and some crayon-munchers (or, "designers"). Like all the best and trendiest creative studios, we have tunes. Our tunes consists of a set of speakers that whoever wants to can plug into their machine, and DJ their little socks off via iTunes, Spotify, VLC or whatever their music player of choice happens to be. Obviously, this lacks finesse. What we WANT is this: a single, dedicated machine running some sort of audio player (ideally Win-based, but a Linux flavour isn't impossible), that exposes an API. We (ie: me and the other devs) want to write a web-based client onto it, that'll let us remotely do all sorts of funky stuff like generating on-the-fly genre-based playlists, and voting for tracks, and making tea. My question - and please forgive me if this isn't the place for such a question, I was going to ask on Stackoverflow but that didn't seem right either - is this: what's the best player to start with? What can do all of this? I know VLC can function as a streaming server, but know nothing of any API it may have. I'd rather chop my pinky off than use iTunes, but if it does what we want, then... Anyhow, thanks for reading. All comments and suggestions gratefully received.

  Read the article

• Any ideas why Ettercap filters aren't seeing packet data?

  - by Bryan

  I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

  Read the article

• Servers - Buying New vs Buying Second-hand

  - by Django Reinhardt

  We're currently in the process of adding additional servers to our website. We have a pretty simple topology planned: A Firewall/Router Server infront of a Web Application Server and Database Server. Here's a simple (and technically incorrect) diagram that I used in a previous question to illustrate what I mean: We're now wondering about the specs of our two new machines (the Web App and Firewall servers) and whether we can get away with buying a couple of old servers. (Note: Both machines will be running Windows Server 2008 R2.) We're not too concerned about our Firewall/Router server as we're pretty sure it won't be taxed too heavily, but we are interested in our Web App server. I realise that answering this type of question is really difficult without a ton of specifics on users, bandwidth, concurrent sessions, etc, etc., so I just want to focus on the general wisdom on buying old versus new. I had originally specced a new Dell PowerEdge R300 (1U Rack) for our company. In short, because we're going to be caching as much data as possible, I focussed on Processor Speed and Memory: Quad-Core Intel Xeon X3323 2.5Ghz (2x3M Cache) 1333Mhz FSB 16GB DDR2 667Mhz But when I was looking for a cheap second-hand machine for our Firewall/Router, I came across several machines that made our engineer ask a very reasonable question: If we stuck a boat load of RAM in this thing, wouldn't it do for the Web App Server and save us a ton of money in the process? For example, what about a second-hand machine with the following specs: 2x Dual-Core AMD Opteron 2218 2.6Ghz (2MB Cache) 1000Mhz HT 16GB DDR2 667Mhz Would it really be comparable with the more expensive (new) server above? Our engineer postulated that the reason companies upgrade their servers to newer processors is often because they want to reduce their power costs, and that a 2.6Ghz processor was still a 2.6Ghz processor, no matter when it was made. Benchmarks on various sites don't really support this theory, but I was wondering what server admin thought. Thanks for any advice.

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Full Apache config migration

  - by Victor Rashkov

  I searched alot and didn't find an applicable answer. I have a working LAMP setup on Ubuntu machine and I have to migrate to a new server in a different country. The old server is 11.10, the new server is 12.04LTS. My problem is that I simply can not remember the steps I followed when I configured the current server which is not the basic LAMP install. It is Apache with FastCGI, SuEXEC, a GD library, worker MPM and all sitting on top of a mhddfs system. There are also other configs I've changed and I can not recall what they are. Because of the complexity of the setup, my attempts to migrate to the new server fail. I get permissions errors, cgi problems etc. Therefore my question is : Is there a sane way to simply tar a full backup of the current web server installation, including MySQL, Php amd the apache server with all configs, and then move it to the new machine? I shall be forever thankful on any advise. So far non of thise I found here gave me an answer. Thanks!

  Read the article

• Hyper-V vss-writer not making current copies [migrated]

  - by Martinnj

  I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

  Read the article

• How can I rapidly switch hosts?

  - by EAMann

  I'm in the process of migrating a forum setup from one version of the software on one machine (older shared Windows host) to a new VPS (Windows Server 2008). To install the software, I used my hosts file to temporarily point the domain at the new IP address. To see the old site, I obviously re-edit the hosts file to remove the reference. But this leaves me constantly adding/removing a # from my hosts file just so I can switch back and forth between the two servers. Is there a way to do this more rapidly? I've found a handful of toggling batch scripts, but all they do is automate the addition/removal of the # character ... so there's still a noticeable lag where I have to repeatedly hit F5 to force my system to detect the new settings. Ideally, I could view both servers at the same time on the same machine. Maybe one through a regular browser session and one through some kind of a proxy. Unfortunately, I don't have the first idea how to set that up. Ideas?

  Read the article

• Network problems that might be related to NAT

  - by nenne

  Hello, I have an odd setup where there is a router(Router 2) routing between network network 1 and network 2. One router(Router 1) with nat for internet access that routes between internet and network 1. There are people in both of these networks. All the clients in network 1 can access the internet, the clients in network 2 can access the clients in network 1 and can also access the router 1. Router 1 can also access clients in network 2. However, the clients in network 2 cannot reach the internet. I cannot think about anything in the routing tables that would hinder this, since Router 1 can reach the clients in network 2 and vice versa. Can it be that nat starts the session between router 2 and the internet site/machine instead of the client and the internet machine? Does anyone have any ideas? I have very little control over router 2(its basicly an ISP vpn net service) but full access to router 1. Its an ubuntu 10.04 with iptables for nat/firewall setup.

  Read the article

• As an admin, what tools do you use to log what you do to your boxes?

  - by Jerry

  I am more of a linux applications developer than an admin. Over time, I've built servers and maintained them, sometimes to offer services, mostly just to develop the applications I work on. Way back when I would create a file in my account to keep notes on what I did on each machine, so that I could replicate that when I migrated to other machines. Nowadays, I install something a private trac installation, install it's blog plugin, and then use that to make notes of everything I install, and most commands that I run, as well as the output. This provides me a combination wiki and blog that I find very useful as a "captain's log". I do this mostly so that when I migrate to a new clean machine, I have a much easier time in bringing it up. And yet, I am always amazed when I see others just install this, delete that, run this, setup this config, ... without seeming to use any way to actually note what they are doing. What do YOU do, and what tools are available? I am especially interested in the transition between maintaining a few machines for a few people and maintaining several to dozens of machines providing a real service. What are the best practices, and where can I find good resources? Thanks!

  Read the article

• (Windows 7) Shared External Drive Permission Issues

  - by connec

  So, say I share my system (C) drive through windows (E.g. properties -> Sharing -> Advanced Sharing -> Share this Folder). I can then access this drive at \\Comp\C on another networked computer - all is well. However, if I insert a removable (USB) disk, say "E", and proceed to share it the same way, when I attempt to access \\Comp\E (either directly or through browsing) I get an error: Windows cannot access \\Comp\E You do not have permission to access \\Comp\E. Contact your network administrator to request access. Now, the permissions (Advanced Sharing -> Permissions) are set with "Everyone" having read access (same as the internal drive), so this doesn't make a lot of sense. Also of note, I have an SSH server on my computer (through Cygwin) and even through SSH (logging in as an administrator user) I cannot access /cygdrive/e (although /cygdrive/c is accessible). As a final note, the drive is of course accessible on the host machine (E:\), and also at \\Comp\E on the host machine.

  Read the article

• Possible for linux bridge to intercept traffic?

  - by A G

  I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also have an application listening on port 8080 of this machine. Is it possible to have traffic destined for port 80 to be passed to my application? I have done some research and it looks like it could be done using ebtables and iptables. Here is the rest of my setup: //set the ebtables to pass this traffic up to ip for processing; DROP on the broute table should do this ebtables -t broute -A BROUTING -p ipv4 --ip-proto tcp --ip-dport 80 -j redirect --redirect-target DROP //set iptables to forward this traffic to my app listening on port 8080 iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 8080 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1/1 //once the flows are marked, have them delivered locally via loopback interface ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 //enable ip packet forwarding echo 1 > /proc/sys/net/ipv4/ip_forward However nothing is coming into my application. Am I missing anything? My understanding is that the target DROP on the broute BROUTING chain will push it up to be processed by iptables. Secondly, are there any other alternatives I should investigate? Edit: IPtables gets it at nat PREROUTING, but it looks like it drops after that; the INPUT chain (in either mangle or filter) doesn't see the packet.

  Read the article

• Proxmox: VMs and different public IPs

  - by Raj

  I have a server which has two NICs and both are directly connected to internet. I have five different public IP addresses available for the VMs. The host machine (Proxmox) doesn't need to use any (it'll use a private IP and that's all) but will have internet connection. I've gone through the Proxmox documentation and I'm not able to understand the big picture to set up the right network configuration for my needs. In short, what I have is: One server (Proxmox, host machine) On that server, 5 VMs are created 5 public IP addresses available (one for each VM), let's say: 80.123.21.1, 80.123.21.2, 80.123.21.3, 80.123.21.4, 80.123.21.5 What I have now for the host is the following: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto eth1 iface eth1 inet manual auto vmbr0 iface vmbr0 inet static address 192.168.1.101 netmask 255.255.255.0 bridge_ports eth0 bridge_stp off bridge_fd 0 auto vmbr1 iface vmbr1 inet manual It can be reached from the internal network, so that's OK. It has internet connection, which is also OK. vmbr1 is going to be used by the VMs. Each VM will have its own IP on his network interfaces configuration file. For some reason, VMs will not have internet and they won't be able to have public IP address. If I use NAT, it will work correctly, but they will not use the public allocated IP addresses for them. Am I missing something?

  Read the article

• How do I configure IIS to allow access to network resources for PHP scripts?

  - by Dereleased

  I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

  Read the article

• Is there a way to log commands that a user runs in Windows 7?

  - by camster342

  I manage a large enterprise environment, and while we try to advise users not to, there are inevitably users that need to have local admin access to their machines. The problem is that some of these users like to "fiddle" and sometimes screw up their machines in "wonderful" ways. Is there an easy way to log what a user does on a machine, specifically in the command prompt? Maybe there is 3rd party tools I could use to log this information? With Linux that I used to use in past ages, you could look at a users bash history file to see what commands they have run. While I realise that specific log could also be altered by the user if they wanted to cover their tracks, that is the sort of log I'm looking for. If there are other ways I can also log what other system configuration type changes they make as well (not necessarily command line based), that's also useful. I know about event/system logs and so on, but that doesn't necessarily catch all the information I need to figure out how the user has buggered their machine this time.

  Read the article

< Previous Page | 264 265 266 267 268 269 270 271 272 273 274 275  | Next Page >