Search Results

Search found 5946 results on 238 pages for 'heavy bytes'.

Page 27/238 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

  • Restoring a Ubuntu Linux LVM drive

    - by user848106
    Scenario: I have a hard disk with a bootable sda1 partition and an Linux LVM. I seem to have corrupted the MBR? or Grub? not sure. I know it no longer boots and even with boot-repair and a Ubuntu live usb I was able to restore it. Following a "fix" with boot-repair I get "missing operating system" Can't i just reinstall grub or a new menu.lst? Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0007b68f Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM

    Read the article

  • ubuntu eth0 not reconnecting after cable unplugged

    - by Alex
    I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

    Read the article

  • Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

    - by skriatok
    I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start Active ruleset: bash-4.1# iptables -L -n -v Chain INPUT (policy DROP 38 packets, 2228 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 844 542K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 38 2228 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4 prefix `FIREWALL:INPUT' 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 38 2228 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4 prefix `FIREWALL:INPUT' Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 1158 111K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Active ruleset: (after editing iptables into below sugested form) bash-4.1# iptables -L -n -v Chain INPUT (policy DROP 2567 packets, 172K bytes) pkts bytes target prot opt in out source destination 49 4157 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 412K 441M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2567 172K LOG all -- * * 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4 prefix `FIREWALL:INPUT' 0 0 DROP icmp -- * * 0.0.0.0/0 0.0.0.0/0 icmp type 8 Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 312K packets, 25M bytes) pkts bytes target prot opt in out source destination ping and syslog simultaneous screenshots from phone (pinger) and from laptop (being pinged) http://dl.dropbox.com/u/4160051/slckwr/pingfrom%20mobile.jpg http://dl.dropbox.com/u/4160051/slckwr/tailsyslog.jpg

    Read the article

  • Has anyone achieved true differential sync with rsync in ESXi?

    - by Julius
    Berate me later on the fact that I'm using the service console to do anything in ESXi... I've got a working rsync binary (v3.0.4) that I can use in ESXi 4.1U1. I tend to use rsync over cp when copying VM's or backups from one local datastore to another local datastore. I've used rsync to copy data from one ESXi box to another but that was just for small files. In now trying to do true differential syncs of backups taken via ghettoVCB between my primary ESXi machine and a secondary one. But even when I do this locally (one datastore to another datastore on the same ESXi machine) rsync appears to copy the files in their entirety. I've got two VMDK's totally 80GB in size, and rsync still takes anywhere between 1 and 2 hours but the VMDK's aren't growing that much daily. Below is the rsync command I'm executing. I am copying locally because ultimately these files will get copied onto a datastore created from a LUN on a remote system. Its not an rsync that'll be serviced by an rsync daemon on a remote system. rsync -avPSI VMBACKUP_2011-06-10_02-27-56/* VMBACKUP_2011-06-01_06-37-11/ --stats --itemize-changes --existing --modify-window=2 --no-whole-file sending incremental file list >f..t...... VM-flat.vmdk 42949672960 100% 15.06MB/s 0:45:20 (xfer#1, to-check=5/6) >f..t...... VM.vmdk 556 100% 4.24kB/s 0:00:00 (xfer#2, to-check=4/6) >f..t...... VM.vmx 3327 100% 25.19kB/s 0:00:00 (xfer#3, to-check=3/6) >f..t...... VM_1-flat.vmdk 42949672960 100% 12.19MB/s 0:56:01 (xfer#4, to-check=2/6) >f..t...... VM_1.vmdk 558 100% 2.51kB/s 0:00:00 (xfer#5, to-check=1/6) >f..t...... STATUS.ok 30 100% 0.02kB/s 0:00:01 (xfer#6, to-check=0/6) Number of files: 6 Number of files transferred: 6 Total file size: 85899350391 bytes Total transferred file size: 85899350391 bytes Literal data: 2429682778 bytes Matched data: 83469667613 bytes File list size: 129 File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 2432530094 Total bytes received: 5243054 sent 2432530094 bytes received 5243054 bytes 295648.92 bytes/sec total size is 85899350391 speedup is 35.24 Is this because ESXi is itself making so many changes to the VMDK's that as far as rsync is concerned the entire file has to be retransmitted? Has anyone actually achieved actual diff sync with ESXi?

    Read the article

  • Odd Suhosin memory alerts

    - by slice
    I am getting a lot of odd suhosin alerts in my syslog. The following are example entries: Jun 9 08:46:11 suhosin[9764]: ALERT - script tried to increase memory_limit to 2145386496 bytes which is above the allowed value (attacker '157.55.39.180', file '/var/www/site/index.php') Jun 9 08:46:11 suhosin[9744]: ALERT - script tried to increase memory_limit to 2145386496 bytes which is above the allowed value (attacker '109.74.2.136', file '/var/www/site/test.php') Jun 9 08:46:13 suhosin[9779]: ALERT - script tried to increase memory_limit to 0 bytes which is above the allowed value (attacker 'REMOTE_ADDR not set', file 'unknown') Jun 9 08:46:13 suhosin[9779]: ALERT - script tried to increase memory_limit to 2145386496 bytes which is above the allowed value (attacker 'REMOTE_ADDR not set', file 'unknown') What is happening here? Why 0 bytes or 2145386496 bytes (2046 GB!!??)? Why does it sometimes state the attacker and the requested script and sometimes state 'REMOTE_ADDR not set' and file 'unknown'? How do I proceed to figure this out?

    Read the article

  • Firewall still blocking port 53 despite listing otherwise?

    - by Tom
    I have 3 nodes with virtually the same iptables rules loaded from a bash script, but one particular node is blocking traffic on port 53 despite listing it's accepting it: $ iptables --list -v Chain INPUT (policy DROP 8886 packets, 657K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo any anywhere anywhere 2 122 ACCEPT icmp -- any any anywhere anywhere icmp echo-request 20738 5600K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- eth1 any anywhere node1.com multiport dports http,smtp 0 0 ACCEPT udp -- eth1 any anywhere ns.node1.com udp dpt:domain 0 0 ACCEPT tcp -- eth1 any anywhere ns.node1.com tcp dpt:domain 0 0 ACCEPT all -- eth0 any node2.backend anywhere 21 1260 ACCEPT all -- eth0 any node3.backend anywhere 0 0 ACCEPT all -- eth0 any node4.backend anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 15804 packets, 26M bytes) pkts bytes target prot opt in out source destination nmap -sV -p 53 ns.node1.com // From remote server Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2011-02-24 11:44 EST Interesting ports on ns.node1.com (1.2.3.4): PORT STATE SERVICE VERSION 53/tcp filtered domain Nmap finished: 1 IP address (1 host up) scanned in 0.336 seconds Any ideas? Thanks

    Read the article

  • Can't ping Ip over bridge

    - by tmn29a
    I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

    Read the article

  • iptables block everything except http

    - by arminb
    I'm trying to configure my iptables to block any network traffic except HTTP: iptables -P INPUT DROP #set policy of INPUT to DROP iptables -P OUTPUT DROP #set policy of OUTPUT to DROP iptables -A INPUT -p tcp --sport 80 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT The iptables output (iptables -L -v) gives me: Chain INPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 4 745 ACCEPT tcp -- any any anywhere anywhere tcp spt:http state RELATED,ESTABLISHED Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 2 330 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http state NEW,ESTABLISHED When I try to wget 127.0.0.1 (yes i do have a web server and it works fine) i get: --2012-11-14 16:29:01-- http://127.0.0.1/ Connecting to 127.0.0.1:80... The request never finishes. What am I doing wrong? I'm setting iptables to DROP everything by default and add a rule to ACCEPT HTTP.

    Read the article

  • Enlarge partition on SD card

    - by chenwj
    I have followed Cloning an SD card onto a larger SD card to clone a 2G SD card to a 32G SD card, and the file system is ext4. However, on the 32G SD card I only can see 2G space available. Is there a way to maximize it out? Here is the output of fdisk: Command (m for help): p Disk /dev/sdb: 32.0 GB, 32026656768 bytes 64 heads, 32 sectors/track, 30543 cylinders, total 62552064 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e015a Device Boot Start End Blocks Id System /dev/sdb1 * 32 147455 73712 c W95 FAT32 (LBA) /dev/sdb2 147456 3994623 1923584 83 Linux I want to make /dev/sdb2 use up the remaining space. I try resize2fs /dev/sdb after dd, but get message below: $ sudo resize2fs /dev/sdb resize2fs 1.42 (29-Nov-2011) resize2fs: Bad magic number in super-block while trying to open /dev/sdb Couldn't find valid filesystem superblock. Any idea on what I am doing wrong? Thanks.

    Read the article

  • Is JPA + EJB to much slow (or heavy) for over Internet transactions?

    - by Xavier Callejas
    Hi, I am developing a stand-alone java client application that connects to a Glassfish v3 application for JPA/EJB facade style transactions. In other words, my client application do not connect directly to the database to CRUD, but it transfers JPA objets using EJB stateless sessions. I have scenarios where this client application will be used in an external network connected with a VPN over Internet with a client connection of 512kbp/DSL, and a simple query takes so much time, I'm seeing the traffic graph and when I merge a entity in the client application I see megabytes of traffic (I couldn't believe how a purchase order entity could weight more than 1 mb). I have LAZY fetch in almost every many-to-many relationship, but I have a lot of many-to-one relationships between entities (but this is the great advantage of JPA!). Could I do something to accelerate the the speed of transactions between JPA/EJB server and the remote java client? Thank you in advance.

    Read the article

  • How to schedule heavy work for later display for Listviews?

    - by Pentium10
    I have a listview with 200 items. I use a custom view for each row. There is a code that takes some time to calculate, and because of this the list hangs out on scrolling and loads in slow (2-3sec). I have subclassed SimpleCursorAdapter, and using Filterable and SectionIndexer. I have in mind to show initially the name of the record, and put in a thread the calculation, and will show up later when it's done. How do I push back some work, and later update the listview to include the calculated data? This should show up on fly without user interaction.

    Read the article

  • Dual Boot issues with Windows 7 and Ubuntu

    - by Michael
    I'm finding myself in a rather unique situation. I've read through just about every resource I can find about this and while things have helped me understand some background, I haven't yet been able to find a solution. So I'm asking here. I originally had just a Windows 7 64-bit OS installation on my desktop. Learning that I couldn't do anything with Apache, PHP and MySql from within a 64-bit system, I did some research and found out that I could use Ubuntu. I've installed the latest version: 11.04. I created a CD to install Ubuntu from and the install went just fine. I installed it side-by-side with Windows 7. I can boot into Ubuntu just fine through the dual-boot option. When I reboot to load Windows though, the Grub2 list shows Windows 7 (loader) and when I select this option the Windows System Recovery loads instead of the actual OS. I haven't made it past there because I didn't know what to do. I just shut the computer down and rebooted into Ubuntu. I've been working for the last hour and a half to try to figure out how to boot into the Windows 7 OS and I haven't got a clue. While I'm somewhat proficient with Windows 7, I'm totally new to Ubuntu, so if you do know what needs to happen, please keep it simple enough that I'll be able to understand. Thanks for all your help in advance. Here's the results after using the Boot Info Script: Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #5 for cbh. => Windows is installed in the MBR of /dev/sdb => Grub 2 is installed in the MBR of /dev/mapper/pdc_bdadcfbdif and looks on the same drive in partition #5 for cbh. sda1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD sdb2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /boot/BCD sdb4: _________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb6: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: pdc_bdadcfbdif1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD pdc_bdadcfbdif2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files/dirs: /bootmgr /Boot/BCD /Windows/System32/winload.exe pdc_bdadcfbdif3: _________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy mount: unknown filesystem type '' =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sda2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/sda3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sdb2 206,911 1,342,554,688 1,342,347,778 7 HPFS/NTFS /dev/sdb3 1,930,344,448 1,953,521,663 23,177,216 7 HPFS/NTFS /dev/sdb4 1,342,556,158 1,930,344,447 587,788,290 5 Extended /dev/sdb5 1,342,556,160 1,896,806,399 554,250,240 83 Linux /dev/sdb6 1,896,808,448 1,930,344,447 33,536,000 82 Linux swap / Solaris Drive: pdc_bdadcfbdif ___________________ _____________________________________________________ Disk /dev/mapper/pdc_bdadcfbdif: 750.0 GB, 749999947776 bytes 255 heads, 63 sectors/track, 91182 cylinders, total 1464843648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/mapper/pdc_bdadcfbdif1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 ends after the last sector of /dev/mapper/pdc_bdadcfbdif blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/mapper/pdc_bdadcfbdif1 888E54CC8E54B482 ntfs SYSTEM /dev/mapper/pdc_bdadcfbdif2 C2766BF6766BEA1D ntfs OS /dev/mapper/pdc_bdadcfbdif: PTTYPE="dos" /dev/sda1 888E54CC8E54B482 ntfs SYSTEM /dev/sda2 C2766BF6766BEA1D ntfs OS /dev/sda3 BE6CA31D6CA2CF87 ntfs HP_RECOVERY /dev/sda promise_fasttrack_raid_member /dev/sdb1 20B65685B6565B7C ntfs SYSTEM /dev/sdb2 B4467A314679F508 ntfs HP /dev/sdb3 6E10B7A410B77227 ntfs FACTORY_IMAGE /dev/sdb4: PTTYPE="dos" /dev/sdb5 266f9801-cf4f-4acc-affa-2092be035f0c ext4 /dev/sdb6 1df35749-a887-45ff-a3de-edd52239847d swap /dev/sdb: PTTYPE="dos" error: /dev/mapper/pdc_bdadcfbdif3: No such file or directory error: /dev/sdc: No medium found error: /dev/sdd: No medium found error: /dev/sde: No medium found error: /dev/sdf: No medium found error: /dev/sdg: No medium found ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sdb5 / ext4 (rw,errors=remount-ro,commit=0) =========================== sdb5/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc- affa-2092be035f0c ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic-pae } menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c echo 'Loading Linux 2.6.38-8-generic-pae ...' linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc-affa-2092be035f0c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic-pae } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sdb1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos1)' search --no-floppy --fs-uuid --set=root 20B65685B6565B7C chainloader +1 } menuentry "Windows Recovery Environment (loader) (on /dev/sdb3)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos3)' search --no-floppy --fs-uuid --set=root 6E10B7A410B77227 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sdb5/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdb5 during installation UUID=266f9801-cf4f-4acc-affa-2092be035f0c / ext4 errors=remount-ro 0 1 # swap was on /dev/sdb6 during installation UUID=1df35749-a887-45ff-a3de-edd52239847d none swap sw 0 0 =================== sdb5: Location of files loaded by Grub: =================== 900.1GB: boot/grub/core.img 825.0GB: boot/grub/grub.cfg 688.7GB: boot/initrd.img-2.6.38-8-generic-pae 688.0GB: boot/vmlinuz-2.6.38-8-generic-pae 688.7GB: initrd.img 688.0GB: vmlinuz =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on pdc_bdadcfbdif3 =======Devices which don't seem to have a corresponding hard drive============== sdc sdd sde sdf sdg =============================== StdErr Messages: =============================== ERROR: dos: partition address past end of RAID device hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory ERROR: dos: partition address past end of RAID device

    Read the article

  • How to tell if SPARC T4 crypto is being used?

    - by danx
    A question that often comes up when running applications on SPARC T4 systems is "How can I tell if hardware crypto accleration is being used?" To review, the SPARC T4 processor includes a crypto unit that supports several crypto instructions. For hardware crypto these include 11 AES instructions, 4 xmul* instructions (for AES GCM carryless multiply), mont for Montgomery multiply (optimizes RSA and DSA), and 5 des_* instructions (for DES3). For hardware hash algorithm optimization, the T4 has the md5, sha1, sha256, and sha512 instructions (the last two are used for SHA-224 an SHA-384). First off, it's easy to tell if the processor T4 crypto instructions—use the isainfo -v command and look for "sparcv9" and "aes" (and other hash and crypto algorithms) in the output: $ isainfo -v 64-bit sparcv9 applications crc32c cbcond pause mont mpmul sha512 sha256 sha1 md5 camellia kasumi des aes ima hpc vis3 fmaf asi_blk_init vis2 vis popc These instructions are not-privileged, so are available for direct use in user-level applications and libraries (such as OpenSSL). Here is the "openssl speed -evp" command shown with the built-in t4 engine and with the pkcs11 engine. Both run the T4 AES instructions, but the t4 engine is faster than the pkcs11 engine because it has less overhead (especially for smaller packet sizes): t-4 $ /usr/bin/openssl version OpenSSL 1.0.0j 10 May 2012 t-4 $ /usr/bin/openssl engine (t4) SPARC T4 engine support (dynamic) Dynamic engine loading support (pkcs11) PKCS #11 engine support t-4 $ /usr/bin/openssl speed -evp aes-128-cbc # t4 engine used by default . . . The 'numbers' are in 1000s of bytes per second processed. type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes aes-128-cbc 487777.10k 816822.21k 986012.59k 1017029.97k 1053543.08k t-4 $ /usr/bin/openssl speed -engine pkcs11 -evp aes-128-cbc engine "pkcs11" set. . . . The 'numbers' are in 1000s of bytes per second processed. type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes aes-128-cbc 31703.58k 116636.39k 350672.81k 696170.50k 993599.49k Note: The "-evp" flag indicates use the OpenSSL "EnVeloPe" API, which gives more accurate results. That's because it tells OpenSSL to use the same API that external programs use when calling OpenSSL libcrypto functions, evp(3openssl). DTrace Shows if T4 Crypto Functions Are Used OK, good enough, the isainfo(1) command shows the instructions are present, but how does one know if they are being used? Chi-Chang Lin, who works on Oracle Solaris performance, wrote a Dtrace script to show if T4 instructions are being executed. To show the T4 instructions are being used, run the following Dtrace script. Look for functions named "t4" and "yf" in the output. The OpenSSL T4 engine uses functions named "t4" and the PKCS#11 engine uses functions named "yf". To demonstrate, I'll first run "openssl speed" with the built-in t4 engine then with the pkcs11 engine. The performance numbers are not valid due to dtrace probes slowing things down. t-4 # dtrace -Z -n ' pid$target::*yf*:entry,pid$target::*t4_*:entry{ @[probemod, probefunc] = count();}' \ -c "/usr/bin/openssl speed -evp aes-128-cbc" dtrace: description 'pid$target::*yf*:entry' matched 101 probes . . . dtrace: pid 2029 has exited libcrypto.so.1.0.0 ENGINE_load_t4 1 libcrypto.so.1.0.0 t4_DH 1 libcrypto.so.1.0.0 t4_DSA 1 libcrypto.so.1.0.0 t4_RSA 1 libcrypto.so.1.0.0 t4_destroy 1 libcrypto.so.1.0.0 t4_free_aes_ctr_NIDs 1 libcrypto.so.1.0.0 t4_init 1 libcrypto.so.1.0.0 t4_add_NID 3 libcrypto.so.1.0.0 t4_aes_expand128 5 libcrypto.so.1.0.0 t4_cipher_init_aes 5 libcrypto.so.1.0.0 t4_get_all_ciphers 6 libcrypto.so.1.0.0 t4_get_all_digests 59 libcrypto.so.1.0.0 t4_digest_final_sha1 65 libcrypto.so.1.0.0 t4_digest_init_sha1 65 libcrypto.so.1.0.0 t4_sha1_multiblock 126 libcrypto.so.1.0.0 t4_digest_update_sha1 261 libcrypto.so.1.0.0 t4_aes128_cbc_encrypt 1432979 libcrypto.so.1.0.0 t4_aes128_load_keys_for_encrypt 1432979 libcrypto.so.1.0.0 t4_cipher_do_aes_128_cbc 1432979 t-4 # dtrace -Z -n 'pid$target::*yf*:entry{ @[probemod, probefunc] = count();}   pid$target::*yf*:entry,pid$target::*t4_*:entry{ @[probemod, probefunc] = count();}' \ -c "/usr/bin/openssl speed -engine pkcs11 -evp aes-128-cbc" dtrace: description 'pid$target::*yf*:entry' matched 101 probes engine "pkcs11" set. . . . dtrace: pid 2033 has exited libcrypto.so.1.0.0 ENGINE_load_t4 1 libcrypto.so.1.0.0 t4_DH 1 libcrypto.so.1.0.0 t4_DSA 1 libcrypto.so.1.0.0 t4_RSA 1 libcrypto.so.1.0.0 t4_destroy 1 libcrypto.so.1.0.0 t4_free_aes_ctr_NIDs 1 libcrypto.so.1.0.0 t4_get_all_ciphers 1 libcrypto.so.1.0.0 t4_get_all_digests 1 libsoftcrypto.so.1 rijndael_key_setup_enc_yf 1 libsoftcrypto.so.1 yf_aes_expand128 1 libcrypto.so.1.0.0 t4_add_NID 3 libsoftcrypto.so.1 yf_aes128_cbc_encrypt 1542330 libsoftcrypto.so.1 yf_aes128_load_keys_for_encrypt 1542330 So, as shown above the OpenSSL built-in t4 engine executes t4_* functions (which are hand-coded assembly executing the T4 AES instructions) and the OpenSSL pkcs11 engine executes *yf* functions. Programmatic Use of OpenSSL T4 engine The OpenSSL t4 engine is used automatically with the /usr/bin/openssl command line. Chi-Chang Lin also points out that if you're calling the OpenSSL API (libcrypto.so) from a program, you must call ENGINE_load_built_engines(), otherwise the built-in t4 engine will not be loaded. You do not call ENGINE_set_default(). That's because "openssl speed -evp" test calls ENGINE_load_built_engines() even though the "-engine" option wasn't specified. OpenSSL T4 engine Availability The OpenSSL t4 engine is available with Solaris 11 and 11.1. For Solaris 10 08/11 (U10), you need to use the OpenSSL pkcs311 engine. The OpenSSL t4 engine is distributed only with the version of OpenSSL distributed with Solaris (and not third-party or self-compiled versions of OpenSSL). The OpenSSL engine implements the AES cipher for Solaris 11, released 11/2011. For Solaris 11.1, released 11/2012, the OpenSSL engine adds optimization for the MD5, SHA-1, and SHA-2 hash algorithms, and DES-3. Although the T4 processor has Camillia and Kasumi block cipher instructions, these are not implemented in the OpenSSL T4 engine. The following charts may help view availability of optimizations. The first chart shows what's available with Solaris CLIs and APIs, the second chart shows what's available in Solaris OpenSSL. Native Solaris Optimization for SPARC T4 This table is shows Solaris native CLI and API support. As such, they are all available with the OpenSSL pkcs11 engine. CLIs: "openssl -engine pkcs11", encrypt(1), decrypt(1), mac(1), digest(1), MD5sum(1), SHA1sum(1), SHA224sum(1), SHA256sum(1), SHA384sum(1), SHA512sum(1) APIs: PKCS#11 library libpkcs11(3LIB) (incluDES Openssl pkcs11 engine), libMD(3LIB), and Solaris kernel modules AlgorithmSolaris 1008/11 (U10)Solaris 11Solaris 11.1 AES-ECB, AES-CBC, AES-CTR, AES-CBC AES-CFB128 XXX DES3-ECB, DES3-CBC, DES2-ECB, DES2-CBC, DES-ECB, DES-CBC XXX bignum Montgomery multiply (RSA, DSA) XXX MD5, SHA-1, SHA-256, SHA-384, SHA-512 XXX SHA-224 X ARCFOUR (RC4) X Solaris OpenSSL T4 Engine Optimization This table is for the Solaris OpenSSL built-in t4 engine. Algorithms listed above are also available through the OpenSSL pkcs11 engine. CLI: openssl(1openssl) APIs: openssl(5), engine(3openssl), evp(3openssl), libcrypto crypto(3openssl) AlgorithmSolaris 11Solaris 11SRU2Solaris 11.1 AES-ECB, AES-CBC, AES-CTR, AES-CBC AES-CFB128 XXX DES3-ECB, DES3-CBC, DES-ECB, DES-CBC X bignum Montgomery multiply (RSA, DSA) X MD5, SHA-1, SHA-256, SHA-384, SHA-512 XX SHA-224 X Source Code Availability Solaris Most of the T4 assembly code that called the new T4 crypto instructions was written by Ferenc Rákóczi of the Solaris Security group, with assistance from others. You can download the Solaris source for this and other parts of Solaris as a few zip files at the Oracle Download website. The relevant source files are generally under directories usr/src/common/crypto/{aes,arcfour,des,md5,modes,sha1,sha2}}/sun4v/. and usr/src/common/bignum/sun4v/. Solaris 11 binary is available from the Oracle Solaris 11 download website. OpenSSL t4 engine The source for the OpenSSL t4 engine, which is based on the Solaris source above, is viewable through the OpenGrok source code browser in directory src/components/openssl/openssl-1.0.0/engines/t4 . You can download the source from the same website or through Mercurial source code management, hg(1). Conclusion Oracle Solaris with SPARC T4 provides a rich set of accelerated cryptographic and hash algorithms. Using the latest update, Solaris 11.1, provides the best set of optimized algorithms, but alternatives are often available, sometimes slightly slower, for releases back to Solaris 10 08/11 (U10). Reference See also these earlier blogs. SPARC T4 OpenSSL Engine by myself, Dan Anderson (2011), discusses the Openssl T4 engine and reviews the SPARC T4 processor for the Solaris 11 release. Exciting Crypto Advances with the T4 processor and Oracle Solaris 11 by Valerie Fenwick (2011) discusses crypto algorithms that were optimized for the T4 processor with the Solaris 11 FCS (11/11) and Solaris 10 08/11 (U10) release. T4 Crypto Cheat Sheet by Stefan Hinker (2012) discusses how to make T4 crypto optimization available to various consumers (such as SSH, Java, OpenSSL, Apache, etc.) High Performance Security For Oracle Database and Fusion Middleware Applications using SPARC T4 (PDF, 2012) discusses SPARC T4 and its usage to optimize application security. Configuring Oracle iPlanet WebServer / Oracle Traffic Director to use crypto accelerators on T4-1 servers by Meena Vyas (2012)

    Read the article

  • Delete eth0 avahi from the ifconfig list

    - by sai
    Hello this is the response I get from ifconfig. Now I have two eth0 things being showed up. I need to delete the second one which says eth0:avahi. I posted my ifconfig's response on a site as I has problem using wired internet, and they suggested to remove the eth0 avahi, to get internet. But I am a newbie to linux networking and have no idea how to delete this. response for ifconfig eth0 Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x4000 eth0:avahi Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 inet addr:169.254.10.43 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:28 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:796 errors:0 dropped:0 overruns:0 frame:0 TX packets:796 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:64016 (64.0 KB) TX bytes:64016 (64.0 KB) wlan0 Link encap:Ethernet HWaddr 00:26:82:3c:ac:27 inet6 addr: fe80::226:82ff:fe3c:ac27/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:52142 errors:0 dropped:0 overruns:0 frame:0 TX packets:30404 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:60816983 (60.8 MB) TX bytes:4160159 (4.1 MB)

    Read the article

  • How do I configure networking when using XEN on 12.04 Server

    - by Ingram
    I'm following this guide, https://help.ubuntu.com/community/XenProposed, and I'd like to setup a static IP address, but I don't know how. I'm using 12.04 Server. This is the step I'm having trouble at (I'm using eth1): Edit /etc/network/interfaces, and make it look like this: auto lo iface lo inet loopback auto xenbr0 iface xenbr0 inet dhcp bridge_ports eth0 auto eth0 iface eth0 inet manual I do this, and here is my output from ifconfig: eth1 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:478264 errors:0 dropped:0 overruns:0 frame:0 TX packets:2895 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46470058 (46.4 MB) TX bytes:214620 (214.6 KB) Interrupt:17 Memory:fa000000-fa012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) xenbr0 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 inet addr:192.168.1.122 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::217:a4ff:fef8:7920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:471842 errors:0 dropped:0 overruns:0 frame:0 TX packets:2795 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:37005780 (37.0 MB) TX bytes:182010 (182.0 KB) So how do I give this system a static IP address? Sorry, I'm not that familiar with networking on Ubuntu.

    Read the article

  • Wired Network not working on Ubuntu 11.10 + Strange Behavior with Manual Conf

    - by Mauricio Cruz
    I'm new to Ubuntu - to be honest this is my very first day trying it... and I've already spent hours trying to make my wired connection work. I've been using this wired network with Windows and OSX, and in both systems I also had some trouble trying to connect in the past (and the troubleshooters did their magic and helped me get connected). Today, this is what I got: I'm running Ubuntu 11.10; ifconfig: eth0 Link encap:Ethernet HWaddr 78:2b:cb:c3:bf:8f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:343 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:70 (70.0 B) TX bytes:63273 (63.2 KB) Interrupt:20 Memory:e2e00000-e2e20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1859 errors:0 dropped:0 overruns:0 frame:0 TX packets:1859 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:149368 (149.3 KB) TX bytes:149368 (149.3 KB) wlan0 Link encap:Ethernet HWaddr 10:0b:a9:82:55:c0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:15484 errors:0 dropped:0 overruns:0 frame:0 TX packets:16871 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12048377 (12.0 MB) TX bytes:2677679 (2.6 MB) I also have some information from Windows ipconfig /all that I ran at my friend's machine Ipv6 Address: <address> preferential Ipv4 Address: 172.26.65.23 <preferential> Netmask: 255.255.254.0 Default Gateway: 172.26.64.1 DHCP Server : <address> DNS Servers : <address> DNS Suffix : <suffix> The weird thing is that I've tried to configure everything manually, using "Network Connections". When I add everything inside IPv4 Settings, the connection is finally successful, but only for 4~5 seconds before getting disconnected again... Update:I just changed the Connection Method to "Local-Link Only", and the same described above happens: At first, it says "Connection Stablished", but after a few seconds, the wired network gets disconnected. I hope someone can help me get connected! Thanks!

    Read the article

  • no disk space, cant use internet

    - by James
    after trying to install drivers using sudo apt-get update && sudo apt-get upgrade, im faced with a message saying no space left on device, i ran disk usage analyzer as root and there was three folders namely, main volume, home folder, and my 116gb hard drive (which is practically empty) yet both other folders are full, which is stopping me installing drivers because of space, how do i get ubuntu to use this space on my hard drive? its causing problems because i cant gain access to the internet as i cant download drivers when i havnt got enough space, this happens every time i try it sudo fdisk -l Disk /dev/sda: 120.0GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003eeed Device Boot Start End Blocks Id System /dev/sda1 * 2048 231315455 115656704 83 Linux /dev/sda2 231317502 234440703 1561601 5 Extended /dev/sda5 231317504 234440703 1561600 82 Linux swap / solaris Output of df -h df: '/media/ubuntu/FB18-ED76': No such file or directory Filesysytem Size Used Avail Use% Mounted on /cow 751M 751M 0 100% / udev 740M 12K 740M 1% /dev tmpfs 151M 792K 150M 1% /run /dev/sr0 794M 794M 0 100% /cdrom /dev/loop0 758M 758M 0 100% /rofs none 4.0K 0 4.0K 0% /sys/fs/cgroup tmpfs 751M 1.4M 749M 1% /tmp none 5.0M 4.0K 5.0M 1% /run/lock none 751M 276K 751M 1% /run/shm none 100M 40K 100M 1% /run/user

    Read the article

  • Error mounting: mount exited with exit code 13

    - by Mike Williamson
    I keep a windows partition on my laptop for the occaisional bit of Photoshop work. A while ago I noticed that Windows had disappeared from my grub boot menu and when I try to mount the windows partion, my system hangs for a bit and then I get this: Unable to mount 105 GB Filesystem Error mounting: mount exited with exit code 13: ntfs_attr_pread_i: ntfs_pread failed: Input/output error Failed to calculate free MFT records: Input/output error NTFS is either inconsistent, or there is a hardware fault, or it's a SoftRAID/FakeRAID hardware. In the first case run chkdsk /f on Windows then reboot into Windows twice. The usage of the /f parameter is very important! If the device is a SoftRAID/FakeRAID then first activate it and mount a different device under the /dev/mapper/ directory, (e.g. /dev/mapper/nvidia_eahaabcc1). Please see the 'dmraid' documentation for more details. It seems that chkdsk is a windows command but since I can't boot into windows (since its the windows partition that is the problem) I'm not sure what to do. Here is the output of fdisk to give you the lay of the land: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x98000000 Device Boot Start End Blocks Id System /dev/sda1 1 10199 81923436 83 Linux /dev/sda2 * 10200 22947 102398310 7 HPFS/NTFS /dev/sda3 22948 29164 49938052+ 83 Linux /dev/sda4 29165 30401 9936202+ 5 Extended /dev/sda5 29165 30401 9936171 82 Linux swap / Solaris Any guidance would be appreciated!

    Read the article

  • How to connect to DSL modem using PPPoE?

    - by VJo
    Hello, I am connecting to the internet through a pppoe connection, but for some reason I can not connect to my modem (it's address is 192.168.1.1). Before I set my pppoe connection, I could connect. So, is there a way? EDIT The output of ifconfig is : r@PlaviZec:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:13:d4:f7:02:d4 inet6 addr: fe80::213:d4ff:fef7:2d4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2811 errors:0 dropped:0 overruns:0 frame:0 TX packets:2801 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2538831 (2.5 MB) TX bytes:448591 (448.5 KB) Interrupt:21 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:28 errors:0 dropped:0 overruns:0 frame:0 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1600 (1.6 KB) TX bytes:1600 (1.6 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:92.229.42.177 P-t-P:213.191.64.59 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:2794 errors:0 dropped:0 overruns:0 frame:0 TX packets:2741 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:2476277 (2.4 MB) TX bytes:381240 (381.2 KB)

    Read the article

  • Accessing host LVM partition from Windows XP through Virt.manager 0.8.5 / Qemu / KVM

    - by Nico de Smidt
    Hi, requested use case is having a Windows XP SP3 guest running in 64bit Ubuntu. (Linux pcs 2.6.35-22-server #35-Ubuntu SMP Sat Oct 16 22:02:33 UTC 2010 x86_64 GNU/Linux) I want this guest to access an LVM LV on the Ubuntu disk. I've setup the following LVM config: --- Logical volume --- LV Name /dev/storage/sdc1 VG Name storage LV UUID Zg5IMC-OlqB-prL5-fgg4-3A9A-OgKP-oZ0QkJ LV Write Access read/write LV Status available # open 0 LV Size 1.01 GiB Current LE 259 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 251:3 -- 1) I've setup a storage pool for /dev/storage 2) I've mkfs.vfat /dev/storage/sdc1 3) and made a virtual IDE disk in the virt-manager setup for the guest. Target device: IDE Disk 2 Source path: /dev/storage/sdc1 -- Now when running XP (guest) Windows sees a new disk in Disk Manager and want's to install a partition on it, since it believes the drive is empty. After formatting from within Windows I can put data on the new disk volume. -- Back in Ubuntu however I cannot access this this any more since it created a partition within an LVM Logical Volume. Running fdisk -l shows the following: root@pcs:/media# fdisk -l /dev/storage/sdc1 Disk /dev/storage/sdc1: 1086 MB, 1086324736 bytes 32 heads, 63 sectors/track, 1052 cylinders Units = cylinders of 2016 * 512 = 1032192 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x8d72e4f4 Device Boot Start End Blocks Id System /dev/storage/sdc1p1 1 1050 1058368+ c W95 FAT32 (LBA) -- which seems fine to me, but when trying to mount /dev/storage/sdc1p1 I get the following error: mount /dev/storage/sdc1p1 /media/xp mount: special device /dev/storage/sdc1p1 does not exist which makes sense since in lvdisplay sdc1p1 does not exist Main question: I want to mount the vfat partition in both Ubuntu and XP What am I missing here????? regards, and thanks for your consideration. Nico

    Read the article

  • Missing Operating System after trying to upgrade to Ubuntu 11

    - by Mauricio
    there! After trying to upgrade from Ubuntu 10.04 to 11, the upgrading process stopped when running and then I got an "out of disk, grub rescue" message when booting. After running Boot Repair, I got this results. Now I get "Missing Operating System" whent trying to boot. Bellow I show some results from some commands I gather from help foruns, but I still reached no solution. Could you please help me? Any enlightment will be very helpful! Disk Utility says "Disk has a few bad sectors". When trying to run the Self-test I get "FAILED (Read)" Here we have what Gparted says about the /dev/sda1 partition (ext4): Flags: boot Status: not mounted Warning: e2label: Attempt to read block from filesystem resulted in short read while trying to open /dev/sda1Couldn`t find valid filesystem superblockUnable to read the contents of this filesystem! From sudo fdisk -lI got: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytesDisk identifier: 0x000e0596 Device Boot Start End Blocks Id System/dev/sda1 * 2048 607428607 303713280 83 Linux/dev/sda2 607430654 625141759 8855553 5 Extended/dev/sda5 607430656 625141759 8855552 82 Linux swap / SolarisDisk /dev/sdb: 320.1 GB, 320072933376 bytes255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c3c41 Device Boot Start End Blocks Id System /dev/sdb1 * 63 625137344 312568641 c W95 FAT32 (LBA) " and fromsudo fdisk /dev/sda1I got fdisk: unable to read /dev/sda1: Inappropriate ioctl for device` From sudo mount /dev/sda1 /mntI got: mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so From sudo update-grubI got: error: cannot read from `/dev/sda'. /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?).

    Read the article

  • How to know which partition is which?

    - by user206870
    Well I was just wondering what partition belongs to which. On my computer I have Windows 7 and two Ubuntu systems (it was an accident, which is why I need to know which partition is which). So how do I know which one is which?? PS here's the codes: jp@jp-Satellite-L555D:~$ sudo update-grub [sudo] password for jp: Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.11.0-12-generic Found initrd image: /boot/initrd.img-3.11.0-12-generic Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/sda1 Found Windows 7 (loader) on /dev/sda2 Found Windows Recovery Environment (loader) on /dev/sda3 Found Ubuntu 13.10 (13.10) on /dev/sda7 done jp@jp-Satellite-L555D:~$ sudo fdisk -l Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf6f5148e Device Boot Start End Blocks Id System /dev/sda1 * 2048 3074047 1536000 27 Hidden NTFS WinRE /dev/sda2 3074048 213421022 105173487+ 7 HPFS/NTFS/exFAT /dev/sda3 469676032 488396799 9360384 17 Hidden HPFS/NTFS /dev/sda4 213422078 469676031 128126977 5 Extended /dev/sda5 300185600 463910911 81862656 83 Linux /dev/sda6 463912960 469676031 2881536 82 Linux swap / Solaris /dev/sda7 213422080 300185599 43381760 83 Linux Partition table entries are not in disk order Thanks to whoever can answer this. Another quick question, what is the extended partition??

    Read the article

  • SD-CARD reader does not show in ubuntu

    - by shantanu
    I bought Acer asipre 4250. It have built-in SD card reader. But it is not working. Nothing show in /media or fdisk but something in dmesg. dmesg: new high-speed USB device number 3 using ehci_hcd [ 127.396733] scsi5 : usb-storage 2-2:1.0 [ 128.526562] scsi 5:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 128.532512] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 129.008110] ohci_hcd 0000:00:12.0: PCI INT A disabled [ 129.032083] ohci_hcd 0000:00:13.0: PCI INT A disabled [ 129.056411] ohci_hcd 0000:00:16.0: PCI INT A disabled [ 129.338026] sd 5:0:0:0: [sdb] Attached SCSI removable disk [ 129.808328] ohci_hcd 0000:00:14.5: PCI INT C disabled [ 167.728616] usb 2-2: USB disconnect, device number 3 [ 169.872284] ehci_hcd 0000:00:13.2: PCI INT B disabled [ 169.872340] ehci_hcd 0000:00:13.2: PME# enabled fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0006bc6d Device Boot Start End Blocks Id System /dev/sda1 * 2048 48828415 24413184 7 HPFS/NTFS/exFAT /dev/sda2 48828416 50829311 1000448 82 Linux swap / Solaris /dev/sda3 50829312 99657727 24414208 83 Linux /dev/sda4 99659774 625141759 262740993 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 99659776 275439615 87889920 7 HPFS/NTFS/exFAT /dev/sda6 275441664 451221503 87889920 7 HPFS/NTFS/exFAT /dev/sda7 451223552 625141759 86959104 7 HPFS/NTFS/exFAT I found another problem just right now. I format last three drives as EXT4 with disk utility. But they are showing as NTFS/exFAT in fdisk. :-(

    Read the article

  • how can I fix error: hd0 out of disk?

    - by rux
    I am running Ubuntu 12.04 on a netbook - Acer AS 1410. After a download session, I restarted the computer and it said: error: hd0 out of disk. Press any key to continue... I pressed everything, but it's just frozen there. Any idea what's wrong with it and what I can do to fix it? I haven't been able to run my computer at all since it's frozen like that. Help please! I booted the live cd and ran sudo fdisk -lu into terminal, and here's what it gave me: Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a696263 Device Boot Start End Blocks Id System /dev/sda3 2048 117229567 58613760 5 Extended /dev/sda5 * 71647232 109039615 18696192 83 Linux /dev/sda6 109041664 117229567 4093952 82 Linux swap / Solaris /dev/sda7 4096 71645183 35820544 83 Linux Partition table entries are not in disk order I am somewhat of a beginner in this, so don't know what this means. any ideas? Thanks!

    Read the article

  • GParted in UBUNTU shows entire disk as UNALLOCATED SPACE

    - by msPeachy
    Good day to everyone. I hope someone can help me with my problem. I have a dual boot Windows and Ubuntu system. I recently encountered an hd0 out of disk error and wasn't able to boot Ubuntu. So I booted into Windows, after 2 to 3 times of booting and rebooting Windows, I tried booting Ubuntu but still I get the hd0 out of disk error. I decided to run Ubuntu from LIVEUSB to try to fix my Ubuntu partition using GParted, but when I run GParted, it shows my entire disk as UNALLOCATED SPACE! The strange thing is that Nautilus still shows and mounts my partitions. Also every time I boot into Windows , my partitions exists and I am able to read and write to them. I have no idea what is wrong. Please help! I can't stand using Windows since most of the tools I use are in Ubuntu. I don't mind reinstalling Ubuntu. In fact I already tried reinstalling using the LIVEUSB but I wasn't able to, since GParted or the Ubuntu installer itself does not recognized my partitions and shows the entire disk as unallocated space. I am currently running Ubuntu from LIVEUSB. Here's the outpuf of sudo fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb30ab30a Device Boot Start End Blocks Id System /dev/sda1 * 2048 104869887 52433920 83 Linux /dev/sda2 104869888 105074687 102400 7 HPFS/NTFS/exFAT /dev/sda3 105074688 156149759 25537536 7 HPFS/NTFS/exFAT /dev/sda4 156151800 625153409 234500805 f W95 Ext'd (LBA) /dev/sda5 156151808 169156591 6502392 82 Linux swap / Solaris /dev/sda6 169158656 294991871 62916608 7 HPFS/NTFS/exFAT /dev/sda7 294993920 471037944 88022012+ 7 HPFS/NTFS/exFAT /dev/sda8 471041928 625121152 77039612+ 7 HPFS/NTFS/exFAT When I run, sudo parted -l, I got this error message: ubuntu@ubuntu:~$ sudo parted -l Error: Can't have a partition outside the disk!

    Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >