Search Results

Search found 8184 results on 328 pages for 'kostas menu'.

Page 271/328 | < Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >

• Dell XPS m1530 system cannot boot need 130w or greater

  - by KPS

  I have a Dell XPS M1530 and I lost my old AC adapter but ordered a new one. For the longest time it always had a battery charge so I was able to boot into the OS but now it is completely dead. I have a generic charger that slowly charged the laptop when it was in the OS but does not when the computer is off. When I boot up I get the following error: The AC power adapter type cannot be determined. The system can only boot with a 130 W power adapter or greater. Strike F1 key to shutdown. I cannot even enter the BIOs setup screen or boot menu, is there a way around this? I heard from the local tech that Dell has a special feature to boot from thumb drive before getting past the initial logo. I am doing my best to avoid purchasing a new charger since it worked just fine when the OS was running, I am hoping to get this thing going. Is there a way to charge the battery externally? Thanks in advance for any help!

  Read the article

• "Open file location" is broken for Win Live Photo Gallery and Chrome

  - by Arnold Spence

  Symptoms: Windows Live Photo Gallery: Right clicking on an image (.jpg, .png) and selecting the context menu item "Open file location" should open the containing folder in explorer. Instead, I get an error dialog stating "This file does not have a program associated with it for performing this action. Please install a program or, if one is already installed, create an association in the Default Programs control panel." Chrome: After downloading a file (of any type), clicking the down arrow on the download status bar at the bottom and clicking "Show in folder" results in the same error dialog mentioned above. I'm using Windows 7. I'm pretty sure this is a registry entry gone bad but I've been unable to locate any information about this specific problem. It's not a file type association problem as I am not trying to open the files concerned, I'm trying to open an explorer window at the location for the file. I've found a similar issue that somebody had with explorer itself. However, the suggested registry fixes here for "Folder", "Directory" and "Drive" did not solve the problem. Also, If I use the searchbar in explorer to do a search, right click on a file and choose "Open file location", explorer jumps to that location without any trouble. I have not yet identified other programs with this issue.

  Read the article

• What are some alternatives to word processing with Markdown?

  - by Hassan

  I've used MS Word-style editors for a long time, but I never got used to how unintuitive and cumbersome they are. I'm not talking specifically about MS Word, but also other editors that seem to mimic Word, like OpenOffice, NeoOffice, etc. I've found myself preferring to write in Markdown (much like on this site). I've found a few good Markdown editors, and I like using them a lot more than using Word-style editors. Here is what they generally look like: As you can see, it works much differently than a Word-style editor. This is a generally cleaner way of writing, since formatting is done right in the text, and is extremely simple to use (no highlighting some text, then clicking a button in some menu you have to find). Although editing text this way is great, I've realized that the syntax can only be used for very specific needs (bullets, numbered lists, headings and sub-headings, bold, italic, and some other common ones). However, many features are missing. Here are some features that would be nice in a word processor: Tables. Indenting paragraphs. Good image support (you can link to images, but not add them, since Markdown is just text). More simple to use than Word and its cronies. Cross-platform. Some of these can be fixed with in-line HTML, but nobody wants to do that. It seems Markdown was designed for editing text on the internet. Is there a similar setup that works better for desktop word processors?

  Read the article

• How to Refresh or Reset Windows 8 without the System Reserved partition?

  - by Karan

  The article Refresh and reset your PC mentions exactly what happens during the refresh and reset operations in Windows 8: Refresh The PC boots into Windows RE. Windows RE scans the hard drive for your data, settings, and apps, and puts them aside (on the same drive). Windows RE installs a fresh copy of Windows. Windows RE restores the data, settings, and apps it has set aside into the newly installed copy of Windows. The PC restarts into the newly installed copy of Windows. Reset The PC boots into the Windows Recovery Environment (Windows RE). Windows RE erases and formats the hard drive partitions on which Windows and personal data reside. Windows RE installs a fresh copy of Windows. The PC restarts into the newly installed copy of Windows. It is my understanding that Windows RE (Recovery Environment) is included as part of the System Reserved partition created by default on the first hard disk. The size of this partition has gone up to 350 MB from the 100 MB it used to be in Vista/Windows 7, no doubt as a result of adding these features. Now we have already discussed how to skip the creation of this System Reserved partition during Setup. Basically, the same techniques that used to work with Windows 7 work with Windows 8 as well. What I want to know is, what will be the exact repercussions of not having the System Reserved partition in place? I assume Troubleshoot / Advanced options should still be available as before: But what about the Troubleshoot menu itself? Will the Refresh and Reset options disappear? Will they remain but be unavailable? Or possibly they will throw an error if selected? Also, will it be possible to access and successfully execute these options if installation media is available? Anything else that might be affected?

  Read the article

• How To Map Fn+Key (Multiple Keys) To Other Key in Windows?

  - by Mohamed Meligy

  I've got a ThinkPad W530 laptop, which replaces the Application Key (also known as Menu Key or Mouse Right Click key, usually between Right Alt and Right Ctrl) with the Print Screen key. So, I need to replace Prt/Scr with Application key. That's easy, all key mapping software like SharpKeys or whatever can do that. There are even a few threads in SuperUser about dozen of those. But then, the different part to this question from the others (which is why it's not a duplicate, I think) is that I also don't want to completely lose the Prt/Scr key. I'm thinking about replacing it with either: Fn + Prt/Scr Fn + F2 These seemed to have no special meaning, so, I'm not overriding anything, just adding functionality to either of them (one of them, not both), to be the new Prt/Scr key. I couldn't find any key mapping software that can detect or let me select more than one key to map, even when the other key is something like Fn key (although they all can map Fn key itself, without combination). I know it may make sense why this restriction exists, but it'll be really useful if I can override it though. Do you know any program that can do that? Thanks a lot.

  Read the article

• Windows XP Language, explorer.exe

  - by nmuntz

  Hi, I was given by my company a laptop with Windows XP Professional in Spanish. I would like to translate it to English, since I really DISLIKE to use localized versions of programs. I have read about Windows MUI packs, however you MUST have Windows XP Pro in English in order to translate it to other language, you can't translate it TO English from other language. Since reinstalling the OS using a Win XP CD in english is not an option (don't have the license nor the CD, and don't have domain privileges to rejoin my computer to the domain), I was wondering what are the essential files that contain localized strings of text. I was doing some research, and apparently explorer.exe has many of the Windows Error Messages and other strings. Will replacing my original explorer.exe with one from Windows XP in English be enough (and work) for having a "basic" english version of windows? Im mainly interested in having error messages, start menu, and the control panel in english. Also, does it HAVE to be the same version as the Service Pack im running? Besides explorer.exe are there any other essential files that i should try to get and replace? Do you see any "dangers" in replacing this files with english version ones? Thanks in advance for your help.

  Read the article

• Changing dual-monitor settings without closing the laptop lid on OS X

  - by hekevintran

  I have a Unibody MacBook hooked up to an external display. By default when I boot up, the system will go to dual-monitor mode. I want to use only the external display. The Apple supplied solution to this problem is to close the lid of the laptop which puts the machine into sleep mode and then move the mouse around to wake it up again. Because the machine is being woken up with the lid closed, when the displays are detected the system finds only the external. After the system is functional again, you can open the lid if you want and the laptop screen will be non-functional until you either tell the system to detect displays from the system preferences or you turn off the external display. Every time I want to use only the external display, I must reach my hand over to close the lid, wait for the machine to sleep, jigger the mouse, wait for the machine to wake up, and finally open the lid again because I don't want the machine to overheat. I feel that this is very stupid to have to do. Why is there no button or menu option that says "don't use this screen"? Is there any third-party software way to change the screen setup that does not involve physically closing the lid and playing a game of "are you sleeping" in order to switch such a simple software setting? We are in the 21st Century and honestly this is childish.

  Read the article

• Can gnome windows (in Ubuntu) be individually themed?

  - by Peter.O

  (Yes, "individually themed" is an oxymoron, but I still want it.) I've just moved from Windows to Ubuntu Linux, and although I am enjoying this new adventure playground, I've encountered something quite unexpected... and its bugging me. It is probably because there are so many gnome apps in Ubuntu (... how strange :) This is great. and the range of available apps is excellent! ...but because of this one-stop-shop scenario, most of the windows look remarkably similar. I'm certainly not after bling-maximus, but I would like a few differentiating colours for my not-so-young eyes to help identify an app at a glance (especially in the compiz lists) ... I love compiz :) I thought it was just a bit of razzle-dazzle, and that alone would be enough, but it is actually very practical to boot. So, basically, I'm wondering if there is a way to theme individual window components on a per app basis... especially the window decoration; menu bar, etc. Thanks.

  Read the article

• Can't Install msysgit/tortoisegit

  - by Jay

  I ran msysGit-netinstall-1.7.0.2-preview20100407-2.exe.   (http://code.google.com/p/msysgit/downloads/list) Then I ran TortoiseGit-1.4.4.0-64bit.msi.   (http://code.google.com/p/tortoisegit/downloads/list) msysgit was installed in C:\ TortioseGit appears to have been installed in C:\Program Files\TortoiseGit I have: "Git Clone..." "Git Create repository here" "TortoiseGit" in Explorer context menu. When I try to clone, I get "git have not installed" [sic]. I have tried setting the MSysGit path, in the TortioseGit settings, to everything imaginable. Nothing works. Neither C:\Program Files or C:\Program Files (x86) have a Git folder. The git command gives "command not found" from both cmd.exe and bash (that msysgit installed) I don't not see msysgit in - Control Panel - Programs - Program Features, but I do see TortioseGit in there. I would like a procedure for verifying that msysgit is properly installed. A procedure for uninstalling msysgit would be an added bonus. I would like a procedure for getting TortoiseGit to work. I am running Windows 7 on a MacBook Pro.

  Read the article

• Browser history, by window

  - by Alex

  I use Chrome --but can switch to another browser if the feature I am about to describe is available. Browsing history, AFAIK in Chrome is sorted exclusively chronologically. Very often however, I will be working on a particular task on my laptop and have multiple (read: a lot) of tabs open in a single Chrome window for that task. Before finishing that task, I may need to work on something else --so I will open another window and minimize the other one, and start researching an entirely different issue. Over the course of a day, I may end up with 10-15 windows with many tabs each. This raises two issues: (a) memory usage and (b) quickly switching between the most relevant two or three windows. I solve these two problems like any regular guy probably would --closing windows. I want to be able to reopen specific windows that I have closed, such that the tabs that were open in that window at the time the window was closed will reopen. Ideally, closed windows will be sorted by the time they were closed and identified by the tabs that were open (even more ideally, I would be able to name these windows (contemporaneously or in the history menu)). Now that I describe this, what I am asking is: does any browser offer the ability to "save and close" windows? (This is distinct from an option to auto-restore tabs upon reopening the browser) Thank you.

  Read the article

• Issue booting Linux Mint from Live CD?

  - by Vee

  I had Windows 8 and Linux Mint 15 dual booted on my laptop. When I first installed Linux, I wasn't able to load into because the grub would not show. To fix this, I used boot-repair from a Live CD. This time, I updated to Windows 8.1 and it showed a watermark telling me my secure boot wasn't configured properly. I then went and enabled secure boot (BIOS) and I believe it was after that that the Grub would not show once again. I tried to boot from a Linux CD again but when I try, it gives me the following errors: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... Before, it was giving me an error with sector 0x6d200 or something instead of 0x0. I am completely unsure of what to do. I do not know what other details to give except that this my have happened after I enabled secure boot, and I actually clicked reset to default setting so I am unsure if any other settings were changed in the BIOS menu.

  Read the article

• Prevent Roaming profiles from syncing certain elements

  - by user29919

  Hello everyone, I'm somewhat new to the Server 2008 front, and I'm afraid I've hit my first snag: I've set up roaming profiles, and they appear to be working too well. Is there a way to limit, ideally on a folder/object basis, what gets synced with a roaming profile? What I'm trying to do is: 1) stop my roaming profile from syncing desktop layout - I run a dual-screen desktop and a laptop, and it's really annoying to have to reposition everything after logging onto the laptop, because it forces everything onto one screen. 2) stop it from syncing registry variables - specifically, I want Visual Studio to load different setting files on each computer. Currently, the variable that contains that path is getting synced whenever I log in, so I get the settings from whatever box I last logged out from. 3) stop syncing the start menu - this one's not as big, but I'm noticing 'program not found' icons even for programs that are installed. they work when I click them - they just look ugly. I'm running Windows SBS 2008 x64 with two Win7 clients (x86 Pro, and X64 Ultimate). Is there a simple way to do that? Or am I trying to work too much against what roaming profiles are designed for? I could, of course, set up different profiles for the desktop and laptop, but that seems to defeat the point of roaming profiles entirely... Thanks in advance! Any help will be much appreciated =)

  Read the article

• OSX root user keeps re-enabling itself on reboot

  - by geodave

  Running Snow Leopard. Completely inexplicably, I seem to have enabled the OSX root user by accident. I honestly have no idea how it happened, but if memory serves I was looking at the login pane (with my two user accounts) when I must have hit something, and suddenly the two accounts were replaced by one that just said "Other..." Clicking the "Other..." account allows me to type a username and password, but neither of the normal two accounts would work. Since I never set a root password, it wouldn't let me in that way either. So I booted into Single User mode and ran these commands: /sbin/mount -uw / fsck -fy launchctl load /System/Library/LaunchDaemons/com.apple.DirectoryServices.plist dscl . -passwd /Users/root newpassword and that let me login as root. Then, I went to System Preferences, Accounts, Login Options, clicked Join, Open Directory Utility, and lastly in the Edit menu I clicked "Disable Root User" Great, I thought, back to normal. Except rebooting, I still only have the Other... account visible, and the root password I set beforehand doesn't work anymore! I have to reboot into Single User Mode and go through the whole process again just to get back into the system (as root) How on Earth did I accidentally enable this? I didn't even know about the Directory Utility before now. And most importantly, why the heck would it be re-enabling the root user on boot? Thanks in advance to any help!

  Read the article

• Debian software raid 1: boot from both disk

  - by bsreekanth

  I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

  Read the article

• No OS will boot, all freeze

  - by Gyan

  This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

  Read the article

• Laptop sleep: How to go into S3 easily?

  - by monov

  Laptop: Fujitsu-Siemens Amilo Pi-3525 OS: Vista When my laptop is plugged in and I close the lid, it goes into S1 sleep. This means that there is still: fan noise (annoying when trying to sleep at night) lots of power consumed (so if I then unplug the laptop and toss it in the bag, by the time I'm at school it's already drained and beeping ominously). What I want is S3 sleep, it solves both problems. I've found a roundabout way to go into S3 sleep: Unplug laptop Close lid (or click Sleep in Start menu) Plug laptop back in if needed The question: How do I force Windows to use always use S3 sleep when I close the lid? One thing I've tried is: dumppo admin minsleep=s3 (dumppo from here) Afterwards running just dumppo admin confirms that minsleep has been set, but closing the lid still goes into S1. Also, after a reboot, minsleep is reset to s1. I think dumppo is incompatible with Vista... MCE Standby Tool was recommended as a Vista-compatible alternative to dumppo, but it doesn't have any effect either. I looked in the BIOS settings, but there are no settings relating to ACPI sleeps/suspends there.

  Read the article

• How to set up a serial connection to a Windows 7 computer

  - by oli_arborum

  I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

  Read the article

• vCenter 5.1 SSO Configuration option not available in Web Client?

  - by goober

  Problem I just finished separately installing vCenter Server 5.1. I installed the components separately but on the same machine using a local SQL 2008 R2 DB (not SQL express). Everything appears to be working correctly with the exception of SSO. It doesn't find the AD server. This is to be expected (see below) but I don't know how to fix it. Potential Leads / Steps taken During the install of SSO, I was logged on as a local administrator (waiting on central IT dept to create a service account). As a result, I received a message saying that SSO wouldn't be able to automatically locate the AD. (fair eonugh) After I read up on it a little bit, I believed I could go into the SSO Configuration option in the Web client, like so: However, what I actually see is: I also notice that the "SSO Users and Groups" entry is not there. Betting that has something to do with it as well. Question How can I get the "Configure" Option to show up for SSO? Overall goal: How can I manually enter the AD server in this scenario while logged in as a local administrator? References VMWare vCenter 5.1 Installation: Part 9 (Optional SSO Configuration) [Derek Seaman's Blog] (used the image of correct configuration menu)

  Read the article

• None of usb-controllers are working after a crash

  - by Cray

  So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

  Read the article

• Extract archive here, autodetect subfolder

  - by lorancou

  I use 7-Zip under Windows 7 to extract all kind of archives. The ever-running problem is that there is not a single way to handle subfolders. Some people create their archives like this (let's call it type A): . +-- subfolder ¦   +-- file 1 ¦   +-- file 2 ¦   +-- ... "Extract Here" will extract everything to subfolder/, which is fine; "Extract to <Folder>" will create an extra subfolder level, which is annoying. And other people create them like that (let's call it type B): . +-- file1 +-- file 2 +-- ... "Extract Here" will populate the current folder, which can bring a lot of mess if this folder already contains tons of other files, and which is very annoying; "Extract to <Folder>" will create a subfolder and conveniently stuff it with the archive content, which is fine. So this leaves two options: always choose to "Extract to <Folder>" and live with the extra subfolder for type A archives. Or open the archive before extracting it to check if this is a type A or B, and then appropriately select "Extract Here" or "Extract to <Folder>". I usually do the latter, but I just discovered that KDE is offering a very handy Extract Archive Here, Autodetect Subfolder feature that automates that. It'll "Extract Here" if there's only one subfolder in the archive, otherwise it'll "Extract to <Folder>". I love this idea. Is there a Windows 7 tool offering this option? Preferably integrated in the explorer context menu? Maybe it's hidden somewhere in 7-Zip and I just didn't find it?

  Read the article

• How do I only dp or do just the lines, not the entire block in Vim diff?

  - by hobbes3

  I'm currently using MacVim (Snapshot 64) "Split Diff by..." menu option. The file is Django's my settings.py from version 1.3.1 to a fresh file from version 1.4. (Open the image on a separate window/tab to enlarge.) I know two basic commands do to "obtain" (and replace) a block from the other side. dp to "put" (and replace) a block to the other side. But those two commands writes the entire block, which in MacVim is the purple highlights. If you look at the 2nd block, you can see that from line 2 and 3 only has 2 words that are different: mysite and hobbes3. I just want to replace per line not the entire block. So what is there a command to replace do do and dp per line as oppose to an entire block or do I have to manually type it out? Bonus question: I noticed that once I manually edit a block, I lose the purple highlighting. How do I "refresh" the diff again to include the highlights without reopening the file? Please try to keep the answers Vim-general as oppose to MacVim-specific. Thanks!

  Read the article

• i7 overclocking problem

  - by benwebdev

  Hi everyone, I've got an overclocked system that seems to be misbehaving. When trying to boot up from cold the system just hangs and nothing is output to the screen. Fans are on as they should but nothing happens to finish the boot. From here I have to switch it off then on again and the boot completes. If I go into the tweak menu in the BIOS I'm informed that a boot has failed I've been in touch with Overclockers UK support a bit and theres not yet been a solution. We've mainly been tweaking the voltage for the CPU. Any suggestions? I'm new to Overclocking which is why I got a bundle with OCUK. With this issue happening on Cold Boot too its tricky to test as I have to make a change then wait till the next day. My system is here: Intel Core i7 930 2.80Ghz overclocked to 4GHz Gigabyte X58A-UD3R (BIOS Version: FC) 6GB RAM Power Supply - CoolerMaster Silent Pro M series 700W One suggestion made by OCUK was that maybe its the power supply but I'm not sure and dont have a spare - it's brand new and a pretty expensive piece of kit. Any thoughts on this? Other recomendations for Power? thanks Ben

  Read the article

• Windows XP seemingly out of resources but plenty of free RAM and swap available

  - by Artem Russakovskii

  This one has been bothering me for years and so far I couldn't find an adequate solution. The problem occurs on pretty much every XP install I've done. After opening a variety of programs or the system running existing programs for a while, Windows seemingly runs out of resources, without telling me. There's ALWAYS free RAM. For example, it just happened to me and I had over a gig of free RAM. There are no viruses, spyware, or other nonsense - it is a Windows resource problem, but the question is which resource is it running out of, how does one pinpoint it, and how does one prevent it? Sometimes, this happens after running specific programs - for example, today it happened when I started Photoshop CS4 and Flash CS4 at the same time. I also noticed that restarting The Bat (email client by Ritlabs) seems to get rid of this problem for a while but again, this happens on machines that don't even have The Bat installed. So what does exactly happen? The symptoms are: pressing alt-tab doesn't bring up the list anymore - it just jumps to the next window instantly, very similar to the way Alt-Esc works, however in this case, it's due to not having enough resources to bring up the alt-tab menu random programs would randomly crash, citing random errors, out of memory errors, system resources, inabilities to do system calls, etc. random programs would start missing random parts - for example, Firefox top menus might disappear, pull up partial selections, or not pull up anymore altogether. IE might lose a few of its toolbars. Some programs might fail to redraw or would just plain go gray where the UI used to be. Windows itself never complains about running out of RAM, virtual memory, or anything at all, yet it's running out of something. The only clue I was able to find and apply the fix today was this Desktop Heap Limitation. I haven't confirmed the fix working as not enough time passed. In the meantime, what are everyone's thoughts?

  Read the article

• A tiered approach to cloning linux partitons

  - by Djurdjura

  I'm looking at a strategy for cloning Linux (root) partitions without having to use a Live CD. Literature suggests rightly that the source and target partitions must be umounted to be able to get a clean clone. This assumes that you need to use a LiveCD. I was wondering if instead of requiring a LiveCD, if using a 3rd partition that would emulate the LiveCD functionality, if we can't achieve the same functionality. In other words, at a high level a system with 3 partitions (all bootable): Rescue Partition (LiveCD emulation) Running Partition (Source) Backup Partition (Destination) All 3 partitions are LVMS. When it's time to clone the source partition to the backup (destination) partition, we would boot to the rescue partition, unmount the other 2 partitions (is it required?), run disk check on the source, copy to the destination (dd or simple copy to avoid replicating the defragmentation from the source), run disk check on the destination partition, update Grub menu list to force boot from either partition, and reboot into that partition. My question, is it an approach that you'd recommend? MBR in all this? Any gotchas or extra checks required? Thanks, D. PS. On recommendation from members, posting here instead of stackoverflow.com.

  Read the article

• What are useful .screenrc settings?

  - by gyaresu

  Basically like some of my own that I've posted below. I'm looking for added functionality to the programme 'screen'. At the very least have a look at the last line for a fantastic 'menu bar' at the bottom of a screen session. ## gyaresu's .screenrc 2008-03-25 # http://delicious.com/search?p=screenrc # Don't display the copyright page startup_message off # tab-completion flash in heading bar vbell off # keep scrollback n lines defscrollback 1000 # Doesn't fix scrollback problem on xterm because if you scroll back # all you see is the other terminals history. # termcapinfo xterm|xterms|xs|rxvt ti@:te@ # These will let you use bind -c selectHighs 0 select 10 #these three commands are bind -c selectHighs 1 select 11 #added to the command-class bind -c selectHighs 2 select 12 #selectHighs bind -c selectHighs 3 select 13 bind -c selectHighs 4 select 14 bind -c selectHighs 5 select 15 bind - command -c selectHighs #bind the hyphen to #command-class selectHighs screen -t rtorrent 0 rtorrent #screen -t tunes 1 ncmpc --host=192.168.1.4 --port=6600 #was for connecting to MPD music server. screen -t stuff 1 screen -t irssi 2 irssi screen -t dancing 4 screen -t python 5 python screen -t giantfriend 6 these_are_ssh_to_server_scripts.sh screen -t computerrescue 7 these_are_ssh_to_server_scripts.sh screen -t BMon 8 bmon -p eth0 screen -t htop 9 htop screen -t hellanzb 10 hellanzb screen -t watching 3 #screen -t interactive.fiction 8 #screen -t hellahella 8 paster serve --daemon /home/gyaresu/downloads/hellahella/hella.ini shelltitle "$ |bash" # THIS IS THE PRETTY BIT #change the hardstatus settings to give an window list at the bottom of the ##screen, with the time and date and with the current window highlighted hardstatus alwayslastline #hardstatus string '%{= mK}%-Lw%{= KW}%50>%n%f* %t%{= mK}%+Lw%< %{= kG}%-=%D %d %M %Y %c:%s%{-}' hardstatus string '%{= kG}[ %{G}%H %{g}][%= %{= kw}%?%-Lw%?%{r}(%{W}%n*%f%t%?(%u)%?%{r})%{w}%?%+Lw%?%?%= %{g}][%{B} %d/%m %{W}%c %{g}]'

  Read the article

< Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >