Search Results

Search found 21089 results on 844 pages for 'virtual memory'.

Page 275/844 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

• 2560 x 1600 screen resolution not available when a second monitor is attached.

  - by sgmoore

  I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

  Read the article

• Why does the java -Xmx not working?

  - by Zenofo

  In my Ubuntu 11.10 VPS, Before I run the jar file: # free -m total used free shared buffers cached Mem: 256 5 250 0 0 0 -/+ buffers/cache: 5 250 Swap: 0 0 0 Run a jar file that limited to maximum of 32M memory: java -Xms8m -Xmx32m -jar ./my.jar Now the memory state as follows: # free -m total used free shared buffers cached Mem: 256 155 100 0 0 0 -/+ buffers/cache: 155 100 Swap: 0 0 0 This jar occupied 150M memory. And I can't run any other java command: # java -version Error occurred during initialization of VM Could not reserve enough space for object heap Could not create the Java virtual machine. # java -Xmx8m -version Error occurred during initialization of VM Could not reserve enough space for object heap Could not create the Java virtual machine. I want to know why the -Xmx parameter does not take effect? How can I limit the jar file using the memory?

  Read the article

• Nexenta under KVM?

  - by Nick

  I have an Ubuntu Server running KVM. I'd like to get the benefits of ZFS so I was thinking of installing a virtual machine under KVM running Nexenta (or NexentaStor), allowing that virtual machine to have raw access to a couple of physical hard disks, and then having it share its file system with NFS so that Ubuntu can access it. I've never tried setting up KVM so that the virtual machine has access to physical drives. Does this sound feasible, and is there anything I need to watch out for? Has someone already documented something like this? Does Nexenta/ZFS function basically as well in the virtual environment as if they were running base bones? I can take a small performance hit, but I don't want it to not be as reliable because of the virtualization. Thanks.

  Read the article

• What you'd need to setup BBS?

  - by raspi

  What I need to setup BBS nowadays? I'm thinking of BBBS or PCBoard (no telnet! too new technology). What I've thinked so far, I'd need: virtual machine which runs DOS and hook that virtual COM-port to somekind of virtual VoIP modem software somehow (is there any?). How you can call to it across internet? Can you use HyperTerminal straight with that virtual/real modem? Or will VoIP just garble the modem data and nothing will work?

  Read the article

• Can I automatically add a new host to known_hosts ?

  - by gareth_bowles

  Here's my situation; I'm setting up a test harness that will, from a central client, launch a number of virtual machine instances and then execute commands on them via SSH. The virtual machines will have previously unused hostnames and IP addresses, so they won't be in the ~/.ssh/known_hosts file on the central client. The problem I'm having is that the first SSH command run against a new virtual instance always comes up with an interactive prompt: The authenticity of host '[hostname] ([IP address])' can't be established. RSA key fingerprint is [key fingerprint]. Are you sure you want to continue connecting (yes/no)? Is there a way that I can bypass this and get the new host to be already known to the client machine, maybe by using a public key that's already baked into the virtual machine image ? I'd really like to avoid having to use Expect or whatever to answer the interactive prompt if I can.

  Read the article

• How to add Group in mounting drive in fstab

  - by Master

  I am using this to mount drive at startup /dev/sda5 /media/virtual ntfs defaults,umask=700,uid=1 0 0 This is working fine but i need things 1)By this method all the folders inside the virtual folder have same permissions but i want 700 for virtual directory and 777 for all other directories 2)I want that if i can add group as well in the mount command. Just like uid, if i couol add gid as well. Is it possible

  Read the article

• What XMonad Configuration Best Replicates Default Ion3 Behavior and Feature Set?

  - by mtp

  Not being very familiar with Haskell and lamenting that Ion 3 is now abandonware, I am curious if anyone out there has found a way of replicating the default Ion 3 behavior and aesthetics in XMonad. If I can't have a near-exact replica of Ion 3-style behavior in XMonad, here is what would be critical to me: Virtual desktops that are empty by default and that spawn full-screen applications, which can be split horizontally or vertically evenly, leaving an empty adjacent pane. The panes, which house open windows, are manually resizable, preferably via keyboard. The panes exhibit tabbed behavior, meaning that they can house multiple windows. Windows can be tagged and moved between panes / virtual desktops via keyboard sequence. A given window may be temporarily exploded into full-screen mode via keyboard sequence. Each new virtual desktop starts in the same state—i.e., with one pane. Each virtual desktop may have its panes divided independently of other virtual desktops. From my investigation, it appears that there are several configurations that provide #3. For as much as I want to spend the time to familiarize myself with Haskell, I just simply don't have time. Any suggestions would be greatly appreciated. As far as I can tell, Ion has no conception of master pane or window, so this behavior is not desired.

  Read the article

• VMware + SQL Server - sqlserver.exe not using both CPU cores

  - by fistameeny

  Hi, I am working on a virtual machine that runs SQL Server Express (as part of Sage Line 50 Manufacturing). The details are as follows: Physical Server (host machine) - Intel Xeon Quad Core 2.1GHz - 4GB RAM - VMDK image stored on RAID-5 500GB SATA drives (7200RPM) - Running Ubuntu 10.04 Server 64 bit - VMware Server 2 Virtual Machine - Windows Small Business Server 2003 - Allocated 2 vCPU's and 2GB RAM - Using 100GB pre-allocated flat VMDK file The problem I have is that there is process that runs in SQL Server that is CPU intensive. On the old physical server that we migrated to the virtual machine from, this would utilise both CPU cores so the sqlserver.exe process would be running 100% on each of the CPU cores. On the virtual machine, it only seems to use one of the two CPU cores, meaning that the process is much slower to run. Question Is there a way to force SQL Server (sqlserver.exe process) to use both of the CPU cores, and distribute it's load between them? Is this a VMware setting that needs changing to allow processes to use both cores?

  Read the article

• VirtualBox no network access

  - by Frantumn

  I'm on a work machine, setting up a virtual ubuntu image using virtual box. After I installed the image, I can't seem to connect to the internet. If I look at network and sharing center on my host OS (W7) I see that the VirtualBox Host-Only Network reads as "no network access" How can I set it up so that it uses the same network as the host OS. UPDATE! Okay, is there a way I can tell virtual box host-only network to use a proxy script?

  Read the article

• virsh console and tty size

  - by pehrs

  I have a virtualization server to which I connect over ssh. If I now change the size of the window it will automatically propagate to the server. It's most easily seen using stty -a, checking the columns and row values. I then use virsh console to connect to the serial interface on a KVM based virtual machine. When I now change the size of the window it does not propagate to the virtual server. This is most easily seen by checking stty -a, which is not updated on the virtual machine when I change window size. This means that line breaks does not work correctly in the terminal and any application that relies on window size for formatting (emacs, man, etc) gets messed up unless the window size on the client matches the default size on the server. A workaround is to manually set the window size to match the client window using stty, but I wonder if there is any way to get this information to propagate and set the window size in the virtual machine automatically.

  Read the article

• XCache permission issue

  - by Guilhem Soulas

  I successfully installed XCache on a Linux server where WHM/cPanel is installed too. However when I go to the admin interface it shows me only the cache for the owner of the folder (= a cPanel account). So I copied the admin interface on another cPanel account of the same server and I'm surprised about the memory allocation because it seems to use the memory I set in php.ini for EACH user. So if set the memory size to 64M and I have 10 users, doesn't it mean that XCache can take up to 640M? It's not the behaviour I want because I can't control the memory in that case! I would like to set 64M only for the entire server.

  Read the article

• Shrinking physical volumes in LVM on a Linux Guest in ESXi 5.0

  - by Stew

  The problem: Linux guest (OpenSuse 12.1), with multiple virtual disks attached. 3 disks are in a logical volume, two of which are exactly 2TB. None of the disks are independent, and due to the backup software we use, cannot be independent. When the two 2TB virtual disks are "dependent", the snapshot fails stating that the file is too large for the datastore. When I put those two disks in independent mode, snapshots work fine (the other disk is 1.8TB). I have therefore concluded that even shrinking the two physical disks by 100GB should solve the problem, however I am having trouble conceptualizing how to go about getting those disks smaller without breaking the LVM entirely. The actual LV has 1.3TB free, so there is plenty of space to shrink with. What I need to accomplish: Deallocate 100GB from the two, 2TB virtual disks within the linux guest. Shrink the two virtual disks by 100GB within vsphere (not as complicated). Are there any vsphere/LVM gurus that can give me a clue?

  Read the article

• Windows 7 Paging file apparently not being used

  - by Daniel F.

  I'm running Windows 7 Home Premium 32bit on a mobo with 24GB RAM. Of those 24GB, 20GB are assigned as a RAMDISK via ASRock XFastRAM. This RAMDISK has the drive letter X assigned to it. On X:\ I'm storing the temporary files folder, as well as pagefile.sys. Pagefile.sys has 6GB of size. The X:\ has usually around 14GB free space, so the temporary files are negligible, it's mostly the browsers which are storing their caches on there. Now my issue is that Firefox is crashing a lot on me, no error message pops up, but I know that this is because it's out of memory. I could kind of live with that, but now that I switched from using Eclipse to Android Studio, I know that I'm in trouble, because Java isn't capable of allocating, and Android Studio, together with the Java instances it launches, is quite a memory hog. So I tried to figure out what's wrong, and apparently Windows isn't swapping out memory onto the paging file. While my applications are crashing (firefox) / not starting (java vm's), the paging file is only using constantly around 15% of its size (checked with the performance monitor). 15% equals to 1GB aprox. I know that the correct solution would be to switch to 64 bit Windows, but I had to use the 32 bit version because of driver issues which I had about two years ago, and I guess that I'll have them again if I reformat and install the 64 bit version. Also, the machine is running quite stable, the only issue is the memory, so I'd like to use it as it is (as the apps are installed and configured) Is there a way to make Windows use the paging file more efficiently? None of my processes require more than 1GB, I'd just like it to swap out some seldomly used stuff, like GoogleCrashHandler.exe and stuff like that in order to have "more physical memory avaliable". Is that possible?

  Read the article

• Configuring network entirely VMware Workstation

  - by MRB

  Hello everyone! You could help me how to configure a network entirely virtual with VMWare Workstation 6.5 which has the Windows Server 2003 and XP workstations, but all virtual server and workstation windows xp.Outra thing is through my Windows Server 2003 I will release Internet access for Windows workstations xp.Everyone I'd like to simulate at home as if in a company but everything virtual. My host is a Windows XP thanks!

  Read the article

• Network Block Device (NBD) clients for Windows or similar solutions

  - by przemoc

  Are there any NBD clients for Windows? Strangely, I cannot find any, or I am searching for them in a wrong way. Such client should be possibly a driver with front-end tool (may be a command-line one) allowing to create virtual drives and associate them with given hosts (or simply localhost) and ports where NBD servers are listening. From user perspective virtual drive should be close to what physical drive is, so it should be accessible as something like \\.\PhysicalDriveX (maybe \\.\VirtualDriveX?), be visible in Disk Management (diskmgmt.msc) and mountvol tools at least. (The only thing I found remotely close to NBD on Windows is ImDisk's proxy mode and companion tool devio, but AFAIK ImDisk only works at partition level (so no virtual drive) and devio uses different protocol.) Secondary question is: Are there any (preferably simple) Windows-specific solutions allowing creation of virtual drive delegating read/write request to user-space via some explicit way (like via TCP, IPC, DLL implementing given API, etc.)?

  Read the article

• IPTables forward from only one ip on my server

  - by user1307079

  I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

  Read the article

• Many different BSOD

  - by Exa

  I'm experiencing multiple bluescreens for a couple of months now. Their error code is as diverse as their time of occurence... Sometimes it happens during gaming, sometimes when watching videos, sometimes when the computer is idle. These are the bluescreens I see most often: PAGE_FAULT_IN_NONPAGED_AREA KMODE_EXCEPTION_NOT_HANDLED IRQL_NOT_LESS_OR_EQUAL SYSTEM_SERVICE_EXCEPTION SYSTEM_THREAD_EXCEPTION INTERRUPT_EXCEPTION_NOT_HANDLED DRIVER_IRQL_NOT_LESS_OR_EQUAL DRIVER_OVERRAN_STACK_BUFFER Responsible drivers (according to the memory dumps): hal.dll tcpip.sys dxgmms1.sys ndis.sys mouhid.sys atikmdag.sys dump_atapi.sys and of course: ntoskrnl.exe My first thought was a driver incompatibility because I am using Windows 8 and some of the bluescreens seem to come from driver issues. All drivers are up to date. I'm afraid that my memory is broken or the mainboard or both. I used the windows integrated memtest which didn't find any errors. Memtest86 found some errors. Does it make sense to buy new memory? Couldn't it be a problem of the board as well? I also read that my memory could run at a too low voltage. But it's set to 1.5V as recommended. Another guess would be to set the memory's latencies manually, but how do I know which ones to try? Here is a screenshot of bluescreenview showing the latest bluescreens. Maybe someone has faced the same behavior before and found a solution. Any ideas or suggestions? Current setup on which the bluescreens occur. Windows 8 RTM (6.2.9200) Asrock 970 Extreme4 AMD FX-8150 ATI Radeon HD5850 16 GB RAM (DDR3-1800) Latest drivers for all devices

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• PHP `virtual()` with Apache MultiViews not working after upgrade to Ubuntu 12.04

  - by Izzy

  I use PHP's virtual() directive quite a lot on one of my sites, including central elements. This worked fine for the last ~10 years -- but after upgrading (or rather moving, as it is on a new machine) to Ubuntu 12.04 it somehow got broken. Example setup (simplified) To make it easier to understand, I simplify some things (contents). So say I need a HTML fragment like <P>For further instructions, please look <A HREF='foobar'>here</P> in multiple pages. 10 years ago, I used SSI for that, so it is put into a file in a central place -- so if e.g. the targeted URL changes, I only need to update it in one place. To serve multiple languages, I have Apache's MultiViews enabled -- and at $DOCUMENT_ROOT/central/ there are the files: foobar.html (English variant, and the default) foobar.html.de (German variant). Now in the PHP code, I simply placed: <? virtual("/central/foobar"); ?> and let Apache take care to deliver the correct language variant. The problem As said, this worked fine for about 10 years: German visitors got the German variant, all others the English (depending on their preferred language). But after upgrading to Ubuntu 12.04, it no longer worked: Either nothing was delivered from the virtual() command, or (in connection with framesets) it even ended up in binary gibberish. Trying to figure out what happens, I played with a lot of things. I first thought MultiViews was (somehow) not available anymore -- but calling http://<server>/central/foobar showed the right variant, depending on the configured language preferences. This also proved there was nothing wrong with file permissions. The error.log gave no clues either (no error message thrown). Finally, just as a "last ressort", I changed the PHP command to <? virtual("central/foobar.html"); ?> -- and that very same file was in fact included. So PHP's virtual() function basically worked -- but the language dependend stuff obviously did no longer work together with it as it did before. Of course I tried to find some change (most likely in PHP's virtual() command), using Google a lot, and also searching the questions here -- unfortunately to no avail. Finally: The question Putting "design questions" aside (surely today I would design things differently -- but at least currently I miss the time to change that for a quite huge amount of pages): What can be done to make it work again? I surely missed something -- but I cannot figure out what...

  Read the article

• Is it possible to cause artificial network packet loss or latency?

  - by nbolton

  I'm trying to reproduce some issues on a deployed application where the MSSQL server and client are running in two separate machines. I think there may be network issues between the two machines, so I'd like to try and reproduce these conditions on two Hyper-V virtual machines (on the same virtual server). Of course, the network for these virtual machines is "local" so it's actually far from the conditions in a live environment. Is there a program I can run on either virtual machine which will degrade the network performance? Or maybe any other work arounds? For example, one way to reproduce the conditions may be to run the VMs on separate Hyper-V servers in geographically dispersed locations (so the SQL traffic goes over VPN or something) -- but this is a little long winded I think. There must be a simpler way.

  Read the article

• VPN connection over apache mod_proxy

  - by This is it

  Hi We have several virtual machines which are connected in a private virtual network connection. Internet access for these machines is provided via dedicated virtual machine which has apache proxy server on it (they all use this machine as proxy). The problem now is that from several machines we need to connect to external VPN Server, but it seems that VPN connections don't work over apache proxy. Any suggestions on how to enable VPN connection over apache proxy (or some other proxy)? Some other solution? Thanks

  Read the article

• Increase/refresh the size of the FreeBSD's main partition

  - by Lucas

  I am using VirtualBox and have my FreeBSD mounted on a virtual drive, which recently ran out of space (10 GB) so I have increased the Virtual Drive size up to the 15 GB - started my FreeBSD and its still out of space, because it doesnt "refresh" the main partition size: # df -h Filesystem Size Used Avail Capacity Mounted on /dev/ada0p2 9.3G 9.3G -711M 108% / devfs 1.0k 1.0k 0B 100% /dev How can I set the partition size to the virtual drive size?

  Read the article

• Is there a postfix mysql virtual_maps append_at_origin workaround so I can pipe to external scripts?

  - by FilmJ

  I am using virtual domains, and I'd like to setup the server to alias to custom scripts. I manage all accounts using postfix mappings to mysql. It seems that postfix automatically appends a virtual domain regardless of how the forwarded/aliased result comes back. So even though i have: "|/bin/command" postfix is reading it as: "|/bin/command"@mydomain.com Is there any work-around, or setting I can fix? It would seem than append_at_myorigin=no would be ideal, but that's unsupported according to the documentation. Another option, maybe I can skip virtual aliases altogether and use the "/etc/postfix/aliases" table - assuming all emails go to the main domain. I'll try this, but if anyone has any other ideas how to make it work with virtual domains, please let me know as this would be very useful! Thanks.

  Read the article

• Remote Debian System Preventing Logon

  - by choobablue

  I have a dozen or so single board computers on a network running Debian (squeeze) and access them via ssh (ssh server is dropbear). To give an idea of the hardware of these computers they're 1.2 GHz x86 processors, 1GB of RAM and 4GB flash drives formatted as ext2 (I avoided ext3 to prevent the added flash write stress from journaling), there is also a swap partition on the drive. Normally the setup I'm using works great and I can access all the computers. Every once in a while one will prevent access. What happens is I try to connect via ssh (putty) and it gives me the login prompt, I enter the username and password and it responds 'Access Denied' and it will also refuse any public key in ~/.ssh/authorized_keys. The credentials are correct as they worked previously. The computer responds to pings and putty recognizes the server public key, which implies to me the system is still running. Restarting the server fixes the problem and I can log in again. (I tried a temporary fix of putting shutdown -r now in the root crontab but this doesn't seem to reliably be run once the hang happens) Once I restart however there doesn't seem to be any information in any of the system logs to indicate what happened, the logs are simply empty for that time period, as if the system had crashed. There is some custom software running on the system which appears to stop working (which is why I wanted to ssh to begin with). I'm assuming that this program is the source of the problems but I'm unsure of how it would cause it and how to debug what is happening. The most likely explanation I can think of is that there is a memory leak in the other program that then prevents dropbear from spawning a new login shell (and crontab from executing shutdown) as there is not enough free memory. But looking at memory usage of the other (working) computers there doesn't seem to be any meaningful increase in memory to indicate a leak (unless it's a very big, fast acting and rare leak). I would think that when the OS ran out of memory it would restart the system or kill processes (the Linux kernel restarts right?). The other thing I wonder about is if the fact that they are running off a flash drive could have some effect, especially the swap partition (which I think I should remove to prevent wear of the flash), but the flash drives are young (~1 month) and I don't think that wear would be a factor yet. Does anybody have an idea of what could cause these symptoms, if it could be done by a memory leak, or something else I haven't thought of. And does anybody know of a method to try to debug the problem and find out more information about what's going wrong?

  Read the article

• Azure Linux out of band managment

  - by faker

  I have a Linux (Ubuntu) virtual machine running on Azure. It seems like the only way to connect to it is via SSH. This is OK for normal operation, but what to do when something goes wrong (fsck waiting for user-input, new kernel doesn't boot, mis-configured network, etc.)? There is a grayed out "Connect" button in the management interface, and the help for it says: To access a virtual machine running Windows Server, click Connect and follow the instructions. Enter the password that was set when the virtual machine was created. The Connect button is not available for a virtual machine running Linux, but you can use your favorite SSH program to access it. I've read the documentation on the command line tools, but there is also no way to connect to it. Is there any way for me to get such a console?

  Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >