Search Results

Search found 24814 results on 993 pages for 'linux distro'.

Page 279/993 | < Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >

  • Hostname vs webpage domain.

    - by Mark
    Hi All, Im just starting to look at deploying a webpage and get into the joy of DNS etc. And im wondering how you set up multiple web-servers all with thier own hostnames/public IP addresses, and yet have them serve up a webpage from one domain. For example, lets say you have a website example.com, and an A record in DNS that points at it's IP address of 1.2.3.4 . You want to have two servers, prod1 and prod2 with some kind of load balancer in front of them for fail over reasons. The way I see it you would want to have the hostnames of these servers as prod1.example.com and prod2.example.com and perhaps loadb.example.com. How would you set up the DNS so this would all work. ie you could ssh to any of the server domains, prod1.example.com, prod2.example.com or loadb.example.com and also just use the www.example.com url to go to the website. And would all these server names be resolvable from the public internet and is that safe? This would be a linux environment, for arguments sake ubuntu, a django framework dynamic website, running in apache 2.2 Cheers Mark

    Read the article

  • how to get ip address of a PPP(Point-to-Point Protocol) network interface?

    - by Xsmael
    I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

    Read the article

  • Safe to remove Python2.6 files?

    - by darkfeline
    I'm using Linux Mint 11 (will upgrade soon), and I've noticed that, even though I don't have any python2.6 packages installed with apt, there's a bunch of residual python2.6 files scattered around my drive, including, but not limited to, dist-packages in /usr/lib/python2.6 and various /usr/share stuff. Is there any way to test if these files are still being used? I'm tempted to sudo rm -rf the lot of them, but I'm scared it'll break stuff. Also, does anyone have any idea where these files could have come from? I believe I had python2.6 installed once upon a time, but I made sure to --purge them, so there shouldn't be any trace of them left, right? EDIT: after using a quick script to check all of the files, it appears most of them belong to important packages, so I won't try weeding out the few which I know are probably useless. Although I am curious why so many packages have python2.6 files when I don't even have it installed. These files are not associated with any packages and I'm not sure if they are safe to remove: /usr/bin/ipython2.6 /usr/lib/python2.6/dist-packages/distribute-0.6.15.egg-info /usr/lib/python2.6/dist-packages/easy_install.py /usr/lib/python2.6/dist-packages/IPython /usr/lib/python2.6/dist-packages/ipython-0.10.1.egg-info /usr/lib/python2.6/dist-packages/setuptools /usr/lib/python2.6/dist-packages/setuptools.egg-info /usr/lib/python2.6/dist-packages/setuptools.pth /usr/lib/python2.6/dist-packages/site.py /usr/lib/python2.6/dist-packages/wx.pth /usr/local/lib/python2.6 /usr/local/lib/python2.6/dist-packages /usr/local/lib/python2.6/site-packages /usr/share/man/man1/ipython2.6.1.gz

    Read the article

  • Configure X connections over TCP without using an X connection

    - by Darren Cook
    I want to run a GUI application on a remote machine I only have ssh access to. I don't need to, or want to, see the GUI window. (I know I could use something like ssh -C -X remote_server if I wanted the GUI to be on my client.) I know X is running on the remote machine, as ps shows this: root ... /usr/bin/Xorg :0 -br -audit 0 -auth /var/gdm/:0.Xauth -nolisten tcp vt7 I set DISPLAY=:0.0 but I then get "Xlib: connection to ":0.0" refused by server" when I try to use it. At Get remote x display working in linux without ssh tunneling and Xserver doesn't work unless DISPLAY=0.0 I see the advice to use gdmsetup to allow X to listen on TCP. But, gdmsetup is a GUI application! And trying to run it over ssh -X did not work ("X11 connection rejected because of wrong authentication"). So, is there a text file I can edit to remove -nolisten? And, after editing it, how do I safely restart X, remotely? (There is other stuff running on this machine, so requesting a reboot is possible, but undesirable.) If not, should gdmsetup be able to run over ssh and I should persevere in that direction? UPDATE: I had to do the ssh -X session as root (ssh as a normal user, then sudo or su, does not work.) So, I did the edit with gdmsetup. I then restarted X with gdm-restart. I've also done xhost + from that ssh -X session. The ps line no longer shows the -nolisten tcp part. But still no luck connecting to it, with either DISPLAY=:0 or DISPLAY=localhost:0

    Read the article

  • Problems setting up VLC Sever/client streaming

    - by Ayos
    I'm trying to set up a Linux machine as the server and a Windows XP machine as the client. Both machines are connected to the same local network via a Wi-Fi router. I setup the stream with the following properties : http stream port 8080 play locally And not much else. No firewall on the windows client(Windows firewall is disabled) When I try to open network stream via the client machine(Using VLC or Windows Media Player) I get the following errors: Media Player error code : 0xC00D11B3: Encountered a network Problem. VLC Console: main warning: connection timed out access_mms error: cannot connect to 192.168.1.3:8080 main debug: no access module matching "http" could be loaded main debug: TIMER module_need() : 12625.810 ms - Total 12625.810 ms / 1 intvls (Avg 12625.809 ms) main error: open of `http://192.168.1.3:8080' failed main debug: dead input main debug: repeating item main debug: starting playback of the new playlist item main debug: resyncing on http://192.168.1.3:8080 main debug: http://192.168.1.3:8080 is at 0 main debug: creating new input thread main debug: Creating an input for 'http://192.168.1.3:8080' main debug: using timeshift granularity of 50 MiB, in path 'C:\DOCUME~1\Accer\LOCALS~1\Temp' main debug: `http://192.168.1.3:8080' gives access `http' demux `' path `192.168.1.3:8080' main debug: creating demux: access='http' demux='' location='192.168.1.3:8080' file='\\192.168.1.3:8080' main debug: looking for access_demux module: 0 candidates main debug: no access_demux module matched "http" main debug: TIMER module_need() : 0.461 ms - Total 0.461 ms / 1 intvls (Avg 0.461 ms) main debug: creating access 'http' location='192.168.1.3:8080', path='\\192.168.1.3:8080' main debug: looking for access module: 2 candidates access_http debug: http: server='192.168.1.3' port=8080 file='' main debug: net: connecting to 192.168.1.3 port 8080 qt4 debug: IM: Deleting the input main debug: TIMER input launching for 'http://192.168.1.3:8080' : 13397.979 ms - Total 13397.979 ms / 1 intvls (Avg 13397.978 ms) qt4 debug: IM: Setting an input Need Help. Thanks in advance.

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • How to configure iptables to use apt-get in a server?

    - by segaco
    I'm starting using iptables (newbie) to protect a linux server (specifically Debian 5.0). Before I configure the iptables settings, I can use apt-get without a problem. But after I configure the iptables, the apt-get stop working. For example I use this script in iptables: #!/bin/sh IPT=/sbin/iptables ## FLUSH $IPT -F $IPT -X $IPT -t nat -F $IPT -t nat -X $IPT -t mangle -F $IPT -t mangle -X $IPT -P INPUT DROP $IPT -P OUTPUT DROP $IPT -P FORWARD DROP $IPT -A INPUT -i lo -j ACCEPT $IPT -A OUTPUT -o lo -j ACCEPT $IPT -A INPUT -p tcp --dport 22 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 22 -j ACCEPT $IPT -A INPUT -p tcp --dport 80 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 80 -j ACCEPT $IPT -A INPUT -p tcp --dport 443 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 443 -j ACCEPT # Allow FTP connections @ port 21 $IPT -A INPUT -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT $IPT -A OUTPUT -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT # Allow Active FTP Connections $IPT -A INPUT -p tcp --sport 20 -m state --state ESTABLISHED,RELATED -j ACCEPT $IPT -A OUTPUT -p tcp --dport 20 -m state --state ESTABLISHED -j ACCEPT # Allow Passive FTP Connections $IPT -A INPUT -p tcp --sport 1024: --dport 1024: -m state --state ESTABLISHED -j ACCEPT $IPT -A OUTPUT -p tcp --sport 1024: --dport 1024: -m state --state ESTABLISHED,RELATED -j ACCEPT #DNS $IPT -A OUTPUT -p udp --dport 53 --sport 1024:65535 -j ACCEPT $IPT -A INPUT -p tcp --dport 1:1024 $IPT -A INPUT -p udp --dport 1:1024 $IPT -A INPUT -p tcp --dport 3306 -j DROP $IPT -A INPUT -p tcp --dport 10000 -j DROP $IPT -A INPUT -p udp --dport 10000 -j DROP then when I run apt-get I obtain: core:~# apt-get update 0% [Connecting to ftp.us.debian.org] [Connecting to security.debian.org] [Conne and it stalls. What rules I need to configure to make it works. Thanks

    Read the article

  • Relinking a deleted file

    - by mbac32768
    Sometimes people delete files they shouldn't, a long-running process still has the file open, and recovering the data by catting /proc/<pid>/fd/N just isn't awesome enough. Awesome enough would be if you could "undo" the delete by running some magic option to ln that would let you re-link to the inode number (recovered through lsof). I can't find any Linux tools to do this, least with cursory Googling. What do you got, serverfault? EDIT1: The reason catting the file from /proc/<pid>/fd/N isn't awesome enough is because the process which still has the file open is still writing to it. A delete removes the reference to the inode from the filesystem namespace. What I want is a way of re-creating the reference. EDIT2: 'debugfs ln' works but the risk is too high since it frobs raw filesystem data. The recovered file is also crazy inconsistent. The link count is zero and I can't add links to it. I'm worse off this way since I can just use /proc/<pid>/fd/N to access the data without corrupting my fs.

    Read the article

  • How can see what processes makes my server slow?

    - by Steven
    All my websites on my server are extremely slow or not loading at all. Even server admin (Plesk) will not load some times. There's been no changes to the sites for the last coupple of months. How can I see what processes is making my server slow? My environment looks like this: Server: VPS running Linux 2.8.x OS: Centos 5 Manage interface: Plesk 9.x Memmory: 1024MB CPU: 2.2GHz My websites run on PHP and MySQL. I finally managed to telnet (Putty + SSH) in to my server. Running top did not show any processes using more than max 2% CPU and none were using exesive memmory. I also got a friend to install a program that checks the core files, and all seemed fine. So I'm leaning towards network issues or some other server malfunction. But I'm not able to find out what can be wrong. Here are some answers to Sean Kimball: I don't run mail services on my server yet There are noe specific bandwidth peaks. Prefork looks like this <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> Not sure what you mean with DNS question. But I think it's up and running. There are no processes running wild Where can I find avarage load? Telnet is disabled and I have to log in using SSH :)

    Read the article

  • mysqldump isn't able to export a specific database, phpMyAdmin crashes

    - by Devils Child
    I'm experiencing problems with a database on my server (Note: All other databases work fine). Once I try to export it with mysqldump I get this error: # mysqldump -u root -pXXXXXXXXX databasename > /root/databasename.sql mysqldump: Couldn't execute 'show table status like 'apps'': Lost connection to MySQL server during query (2013) Also, phpMyAdmin throws an error when selecting this database and immediately logs out. However, the web site which uses this database works fine. I can also execute SELECT statements on the table named "apps" from the MySQL shell. I tried restarting the MySQL daemon as well as REPAIR DATABASE and REPAIR TABLE but the problem still persists. I had this problem before, then it disappeared somehow without me doing anything to resolve the issue. Now, the problem is back and I'm simply unable to create a backup of this database. Used software Debian 6.0.7 x64 MySQL 5.1.66-0 MySQL Version: mysql> SHOW VARIABLES LIKE "%version%"; +-------------------------+-------------------+ | Variable_name | Value | +-------------------------+-------------------+ | protocol_version | 10 | | version | 5.1.66-0+squeeze1 | | version_comment | (Debian) | | version_compile_machine | x86_64 | | version_compile_os | debian-linux-gnu | +-------------------------+-------------------+

    Read the article

  • How to copy VirtualBox VDI contents to a partition and dual boot the OS from it?

    - by Calmarius
    I'm a Linux user but I keep a compressed Windows XP ISO with me on a pen drive for the case I absolutely need Windows to do something. This works in VirtualBox most of the time. But now I want to play some games, so I would like to run the Windows image natively. My computer don't have CD drive so cannot just burn the ISO and make an install normally. What I trying to do is moving the installed Windows image to a physical NTFS partition on my HDD and set up GRUB to let me dual boot it. I found many tutorials that deal with making VDI to physical drive. But they assume I want to overwrite my entire drive. Moving the raw disk image with dd to the partition resulted in a corrupt partition. I also tried the VMDK trick to use that empty partition and install the Windows on it. Although the text mode phase of the installation finishes without problems, the VM won't work, either crashes and keeps rebooting or just immediately or freezes (depending on how I created the VMDK, with -rawdisk /dev/sda3 or -rawdisk /dev/sda -partition 3).

    Read the article

  • Configuring WPA WiFi in Ubuntu 10.10

    - by sma
    Hello, I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

    Read the article

  • Why is my rsync so slow?

    - by iblue
    My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

    Read the article

  • Is there a way to use VirtualBox without using it's resource registry?

    - by Catskul
    Summary VirtualBox seems to want everything to be "registered" which makes it much more annoying to work with on the command line. I'm attempting to create an automated script which will create, move, start, stop, and destroy virtual machines and virtual disks. Requiring registration will complicate the task for the following reasons. leaves state information around that can cause unpredicted edgecases causing scripts to fail. creates potential name space collisions for multiple process creating VMs with the same name moving/copying resources on the same machine is more complicated because references in the registry need to be updated copying resources (disk + vm combination) to another machine require reconfiguration once they reach their target machine, and require the transfer of extra meta data to do the reconfiguration. If something unexpectedly fails, and an unregister thus fails to happen, left over configuration information can cause problems in subsequent runs. Use Case My specific use case is for a continuous integration server which creates and destroys VMs and Disk images potentially with the same name, and would require more logic to deal with the registry's statefulness. Imaginary Example It seems that I should just be able to for example (using some imaginary and/or incorrect commands): mkdir foobar customdiskimg_script ./foo/foo.vdi vboxmanage createvm --name "foo" --ostype Linux --basefolder ./foo/foo.xml vboxmanage storagectl ./foo/foo.xml --name foo --add ide vboxmanage storageattach --storagectl foo --medium ./foo/foo.vdi ./foo/foo.xml vboxmanage startvm ./foo/foo.xml TLDR Is there a way to use virtualbox without "registering" harddisks and VMs?

    Read the article

  • Removing all traces of GNU java and openjdk and replacing with Sun JDK

    - by user61766
    I have installed latest Sun JDk. But when I do: java -version I still got OpenJDK version. So I completely removed OpenJDK. But now when I do: java -version I get even older GNU java 1.5 something libgcj. So I completely removed that too but it was asking to remove bunch of dependent apps like OpenOffice.org Writer etc. Even though I need the writer, I let it go because I do not want ever to see the face of any GNU java on my linux. So everything related to GNU java is removed. Luckily I am able to start Eclipse and it works fine and start normally (apparently using the installed Sun JDK which is what I want). But now when I run java -version I get bash: /usr/bin/java: No such file or directory Now what I need to do so that when I open any terminal window and enter java -version I should get Sun JDK version? Sun JDK is installed in /usr/java/jdk1.6.021. I also have symlinks: /usr/java/latest and /usr/java/defaults pointing to sun jdk.

    Read the article

  • Virtual Server HDD shrinks without apparent reason

    - by Christian
    We have a virtual hosted Linux server, and in the last few months every now and then the HDD shrinks from 400GB down to the exact byte count that is in use. All existing data can be downloaded and displayed without a problem, but we can't upload or edit any files because of the "full" hard drive. Here is a screenshot, where "size" should be 400GB: This has happened twice before, and again today. The last times, when I reported the issue to the host, they said "that isn't possible, you must be doing it wrong", but soon after the call, the problem vanished without us doing anything, so I suppose that they have some kind of problem they're not willing to admit. Even after the fact, they acted like nothing was wrong and wrote me a mail in which they explained that I can use "df -h" to view available disk space (well duh, how do you think I noticed this particular issue?). Questions about if and what they had done were ignored. It has happened around the 25th to 28th of the month, so I suspect that they might have a cronjob running every 30 days or so which wreaks havoc with some VM configs. I just want to understand the problem, but the host support hasn't been very helpful in that regard. I have tried Googling the issue, but any combination of search terms I can come up with just gives me tutorials on how to change HDD size in a virtual machine. a) What could be the cause of shrinking HDD size in a Ubuntu 12.04.3 LTS server? Could there be anything in our virtual machine or is it more likely to be an issue with the vm host? b) Can I do anything about it without needing to contact the host's support? c) Is there anyway I can prevent this from happening at all?

    Read the article

  • How can I generate filesystem images that are usable on many different virtualization systems?

    - by Mark Longair
    I have written a script that generates a root filesystem image (based on Debian lenny) suitable for User-Mode Linux. (Essentially this script creates a filesystem image, mounts it with a loop device, uses debootstrap to create a lenny install, sets up a static IP for TUN/TAP networking, adds public keys for login by SSH and installs a web application.) These filesystem images work pretty well with UML, but it would be nice to be able to generate similar images that people can use on alternative virtualization software, and I'm not familiar with these options at all. In particular, since the idea is to use this image as a standalone server for testing the web application, it's important that the networking works. I wonder if anyone can suggest what would be involved in customizing such root filesystem images such that they could be used with other virtualization software, such as VMware, Xen or as an Amazon EC2 instance? Two particular concerns are: If such systems don't use a raw filesystem image (e.g. they need headers with metadata or are compressed in some particular way) do there exist tools to convert between the different formats? I assume that in the filesystem, at least /etc/network/interfaces will have to be customized, but are more involved changes likely to be necessary? Many thanks for any suggestions...

    Read the article

  • Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

    - by user94217
    I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

    Read the article

  • Explain why .bash_logout won't run commands?

    - by Droogans
    So I've been wondering how to run these two lines of code everytime I close an open instance of Terminal: history -c cat /dev/null > ~/.bash_history I export HISTFILE=5 on startup, but still want to flush that out when I'm done. I've tried looking around a bit in a couple of places, and haven't had much luck. I run Linux Mint, and would also note here that I ran into a similar issue with .bash_profile; eventually, I discovered I needed to place all start up code in .bashrc, so maybe that has something to do with it. Here's my .bash_logout file: #!/bin/bash # ~/.bash_logout: executed by bash(1) when login shell exits. # when leaving the console clear the screen to increase privacy if [ "$SHLVL" = 1 ]; then history -c cat /dev/null > ~/.bash_history [ -x /usr/bin/clear_console ] && /usr/bin/clear_console -q fi #this does nothing on exit... echo 'logout'; sleep 2s I've tried re-arranging this script many ways, I'm not sure if I don't understand how bash works, and if any of this is running in the first place. Does the fact that I run Xserver make bash consider Terminal something that isn't a log-out on exit?

    Read the article

  • Fedora Core 6 Migration

    - by Matthew Sprankle
    I am at a loss as to what I should to for this server. I need it to run php5.3 and corresponding version of mysql. I received a client today through work that is using Fedora core 6 running 10 very small websites on some very hodge podge setup. My original idea was just upgrade to php5.3. I have yum (installed 3.0.8) reconfigured for the fedora archive. The latest version of php it allows is 5.1.8. I am still relatively new to server setups and am nervous about wiping their server to upgrade it. Since it is about 6-8 years old I'm not sure if it will even support the newest version of fedora. The server specs are: Parallels Plesk Panel version 9.5.4 Operating system Linux 2.6.9-023stab048.4-smp CPU GenuineIntel, Intel(R) Xeon(R)CPU E5335 @ 2.00GHz (10gb disk space and 1gb of memory). I use fedora for my personal server so I was a little familiar with it. I haven't done anything too extravagant. Is there a way I can escape this nightmare with installing php5.3 or do I need to migrate these sites to a new server?

    Read the article

  • Tunnell network requests with Windows 7

    - by mark
    I've Windows 7 64bit Pro client in a private LAN behind a Netgear wgr614v7 router. I've also a remote Debian server machine outside. I'd like to tunnel all (or specified ports/protocols) over this outside server, so when I'm on the Windows machine and I request serverfault.com it would not appear from the wgr614v7 public IP but from the server. But it's not only about HTTP traffic, it's basically about everything I'd like to: other TCP ports, even UDP, etc. It must be transparent to the application, e.g. they shouldn't be aware of this. All their requests just appear as being from the server and the tunnel between them takes care about the packets. I'm aware of e.g. Putty and forwarding individual ports or using it as a socks proxy, however not many applications to support this and the support in windows itself looks non-existent to me. I might add it should be something "reasonable" easy to set up. I've heard about PPTP but I'm unsure about it's security implications (by design). Should I go for VPN? There seem to be two common solutions for Linux (OpenSwan and StrongSwan), why would I pick the one over the other? I also fear that setting up a VPN might be quite complex, OTOH maybe it's the only sane way to do the things right? Or is OpenVPN sufficient? I'm seeking for open (source) solutions, what other options to I have or which direction should I head to?

    Read the article

  • How to keep multiple servers in sync file wise?

    - by GForceSys
    I'm currently managing a cluster of PHP-FPM servers, all of which tend to get out of sync with each other. The application that I'm using on top of the app servers (Magento) allows for admins to modify various files on the system, but now that the site is in a clustered set up modifying a file only modifies it on a single instance (on one of the app servers) of the various machines in the cluster. Is there an open-source application for Linux that may allow me to keep all of these servers in sync? I have no problem with creating a small VM instance that can listen for changes from machines to sync. In theory, the perfect application would have small clients that run on each machine to be synced, which would talk to the master server which would then decide how/what to sync from each machine. I have already examined the possibilities of running a centralized file server, but unfortunately my app servers are spread out between EC2 and physical machines, which makes this unfeasible. As there are multiple app servers (some of which are dynamically created depending on the load of the site), simply setting up a rsync cron job is not efficient as the cron job would have to be modified on each machine to send files to every other machine in the cluster, and that would just be a whole bunch of unnecessary data transfers/ssh connections.

    Read the article

  • How to prevent response to who-has requests on virtual eth interface?

    - by user42881
    Hi, we use small embedded X86 linux servers equipped with a single physical ethernet port as a gateway for an IP video surveillance application. Each downstream IP cam is mapped to a separate virtual IP address like this: real eth0 IP address= 192.168.1.1, camera 1 (eth0:1) =192.168.1.61, camera 2 (eth0:2) =192.168.1.62, etc. etc. all on the same eth0 physical port. This approach works well, except that a specific third-party windows video recording application running on a separate PC on the same LAN, automatically pings the virtual IPs looking for unique who-has responses on system startup and, when it gets back the same eth0 MAC address for each virtual interface, freaks out and won't allow us to subsequently manually enter those addresses. The windows app doesn't mind, tho, if it receives no answer to the who-has ping. My question - how can we either (a) shut off the who-has responses just for the virtual eth0:x interfaces while keeping them for the primary physical eth0 port, or, in the alternative, spoof a valid but different MAC address for each virtual interface? Thanks!

    Read the article

  • How can I recover my data from a damaged hard drive?

    - by krk
    a few days ago when I was working on windows my laptop was beaten on the side where the hard drive is located. As a result, it was damaged and I couldn't access the windows partition. I had to boot the linux one, which is working without any trouble. I have 2 partition formatted with ntfs, the one with windows on it, and the other one intended to store data. I mounted the windows partition from ubuntu and I could see all my files. But when I tried to mount the data partition it was impossible. It threw me an error, it couldn't recognize ntfs partition. I try to copy the damaged disk into an external hard drive using the command: dd if=/dev/sda of=/dev/sdb conv=noerror,sync The progress stopped at 60%. I was still unable to mount the data partition. Now I'm trying to backup my files using an utility called Photorec. The problem is that it is recovering my files in a disorderly way, it is all mixed up and I need my original directory structure, it will become an endless task to organize the files as they were before. Is there any way I can get my partition back?

    Read the article

  • TGT validation fails, but only for one user

    - by wzzrd
    I'm seeing the weirdest thing here. I have a couple of RHEL3, 4 and 5 machines that validate user credentials through Kerberos with an Active Directoy domain controller as their KDC. This works for all of my users, save one. There is one account that is unable to log into RHEL3 Linux machines and generates the following errors there: May 31 13:53:19 mybox sshd(pam_unix)[7186]: authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=10.0.0.1 user=user May 31 13:53:20 mybox sshd[7186]: pam_krb5: TGT verification failed for `user' May 31 13:53:20 mybox sshd[7186]: pam_krb5: authentication fails for `user' Other accounts, like my own, are fine: May 31 17:25:30 mybox sshd(pam_unix)[12913]: authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=10.0.0.1 user=myuser May 31 17:25:31 mybox sshd[12913]: pam_krb5: TGT for myuser successfully verified May 31 17:25:31 mybox sshd[12913]: pam_krb5: authentication succeeds for `myuser' May 31 17:25:31 mybox sshd(pam_unix)[12915]: session opened for user myuser by (uid=0) As you can see, TGT validation fails. This only happens for this specific account, not for any other. The failing useraccount's password has been reset, I inspected both user objects in Active Directory, but I see nothing out of the ordinary. If I have the failing useraccount log into a RHEL4 or 5 box, there is not problem, so it must be RHEL3 specific, but the fact that only one account suffers from this, alludes me. Maybe someone has seen this before?

    Read the article

< Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >