Search Results

Search found 19934 results on 798 pages for 'usb flash drive'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 285/798 | < Previous Page | 281 282 283 284 285 286 287 288 289 290 291 292  | Next Page >

  • Raid recovery in gigabyte GA-8I945 Pro

    - by epeleg
    This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

    Read the article

  • "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

    - by salparadise
    I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

    Read the article

  • VMWare Workstation 8 Disk I/O & Hard Faults

    - by Scott
    I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

    Read the article

  • How long do uploaded files stay in the tmp folder in Linux Ubuntu?

    - by Jean-Nicolas Boulay Desjardins
    I am building a web application where my users will be able to upload files. After the files are uploaded I need to send the files to two other servers, and after they will be deleted from the server where they were just uploaded to. I am wandering is it a good I idea to keep the uploaded files in the tmp/ folder the time the uploaded files are sent to the other two servers or should I move them to another folder incase they get deleted? I am also wandering because I would like to know if I have to build a cron script to get rid of the files that have been transfered to the other servers so that I get my disk space back.

    Read the article

  • can I consolidate a multi-disk zfs zpool to a single (larger) disk?

    - by rmeden
    I have this zpool: bash-3.2# zpool status dpool pool: dpool state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM dpool ONLINE 0 0 0 c3t600601604F021A009E1F867A3E24E211d0 ONLINE 0 0 0 c3t600601604F021A00141D843A3F24E211d0 ONLINE 0 0 0 I would like to replace both of these disks with a single (larger disk). Can it be done? zpool attach allows me to replace one physical disk, but it won't allow me to replace both at once.

    Read the article

  • Suggestions for Backup solution

    - by jiewmeng
    i am considering between windows home server simple nas extra HDD's in desktop btw, i will be the main user i am looking to fulfil the following needs: reliability (i am think RAID 1 or 5) not so prone to virus/malware infections (will using a separate NAS or home server help? say windows home server is still a windows pc except separated by network?) power efficiency (eg. spin down when not in use) download (eg. i may want to dl big files/torrents overnight and i may not want to use a full powered PC for it? does a full pc vs NAS provide significant power usage to justify cost of new system esp. since i am only user?) performance (i guess i like to write/access my files fast, on 2nd thought, maybe for backup i can forgo this? maybe for a WD Green HDD? but how much slower will it be? plus since i am the only user, i think the whole HDD will be mine?)

    Read the article

  • How do I record sound from my CD/DVD player without other system sounds in the mix?

    - by Software Monkey
    Using GoldWave I can record via the "Stereo Mix" channel, but I get no sound on the "CD" channel. Of course, using the stereo mix also mixes in all system sounds, including beeps, etc. I have the analog out on the DVD player connected to the CD-IN connector on the MoBo. I can hear CDs and DVDs playing just fine through my speakers - is this because the CD is also IDE data connection in to deliver the sound to the sound card, then? I specifically want to record a DVD; I can easily rip a CD using GoldWave's built-in ripper. Is there anything I have forgotten or have to enable? Or is it likely I have a damaged cable? My system is an MSI mobo and is running Windows XP SP3.

    Read the article

  • XP: cannot assign a letter to a FAT32 partition

    - by Toc
    I have an external hard disk, where I have created many partitions to use also in Linux. The first two partitions are FAT32. The third is a Truecrypt Partition. I cannot assign a letter to the second partition. When I go to Manage disk and make right clic on the unassigned partition, most of the items are not enables. See screenshot: http://i42.tinypic.com/ofsh9u.jpg What have I to do to see this partition on my XP pc?

    Read the article

  • Disable RAID Controller

    - by B.Mr.W.
    I have some decent HP Proliants server that come with "HP Smart Array P410i Controller" enabled, I am using these boxes to set up a Hadoop cluster and I know, RAID is for sure a no-no for Hadoop since the application itself will take care of data redundancy and extra intelligence provided by RAID won't be helpful and might turn down the performance. I tried to disable the devices at the BIOS and the box cannot even access the disk afterwards. So I am assuming the controller is sitting between disks and mother board, and we have to turn it on and configure it to "level0" or something like that. I am wondering what should I do to "disable" the RAID functionality so it will fit into the Hadoop environment.

    Read the article

  • Huge HDD response time in Resource monitor

    - by Mille
    Just bought all parts for a computer and put it together and installed a fresh version of windows 7. After a while, when using the computer it gets very slow, and even closing down windows can take several minutes. I started to look in the resource monitor and though I found the answer watching my hdd. The thing is that the hdd completes all tests in Seagate's SeaTools for Windows successfully. Which makes me doubt on the problem and weather I can send it in to get an replacement. Suggestions on what it could be and what I can do about it? Here a screenshoot from the resource monitor:

    Read the article

  • My WD passport detected but not shown on my computer

    - by Rakesh Patel
    1TB WD harddisk is detected in laptop but drives not visible on my computer. Under disk managment drives shown without letters. Right clicking on these drives give 2 options: Delete volume Help. The same harddisk was running well on the same laptop a day before. It is also showing full size of hard drives, Healthy (Primary Partition) etc. (this happened after harddisk usage by guest). Harddisk is new only (about 5 month usage) Please suggest: Is there hardware related problem inside harddisk, if so is it repairable? Is there any option to recover data?

    Read the article

  • Dual boot: Windows XP and Ubuntu

    - by user19455
    (I know that there are some questions similar to this one, but the ones I have read (and I have read more than one, did not answer my question) I have installed, in two physically different hard drives Windows XP and Ubuntu 9.0. I would like to have a dual boot that, if nothing was pressed, the Windows XP would start automatically. I have read about Grub but got the impression that it wasn't possible to default the operating system to start to something other than Ubuntu. Thanks.

    Read the article

  • How should I interpret the specifications of a SSD?

    - by paulgreg
    When considering to buy a SSD, how should I interpret the different specifications of the SSD? Here are some specific things that need to be deciphered: Controller (this can affect performance and endurance more than all other factors combined) Bus Technology Form Factor (Physical Size) Capacity NAND or NOR technology Power Consumption during Read, during Write, when Idle Read/Write Burst and Sustained Throughput All of these things I would like to be explained in more detail and their actual importance in selecting an SSD.

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0 [migrated]

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • Transfer Raid Drives to External Enclosure

    - by dubbeat
    I have 2 raid disks (a grand total of 360GB) in my laptop. I'm fast running out of space and want to install new drives. I've a pretty good idea how to do this. My question is what can I do with the drives that I remove? I've got lots of media files on these drives that I'd like to keep and maybe transfer back onto my laptop once I have the new drives installed. Bearing in mind that I know next to nothing about hardware how do you suggegst I go about reusing the removed drives somehow? Thanks,

    Read the article

  • How can I combine non-identical disks efficiently?

    - by Odys
    There are some not-identical disk of various capacities that I want to combine (somehow). Since there are no duplicate models, I can't use raid between none of them. Is there a way to use them efficiently while being safe? What I have in mind is a software that will use them as if it were Raid-5 or something. I really don't care about max speed. I want in the end to have as less logical drives as possible. Also, I don't mind spending some money on hardware, if needed.

    Read the article

  • 4 month old 500 GB SATA HDD making noise?

    - by metal gear solid
    My 4 month old 500 GB SATA HDD making noise sometimes and the PC hangs when it makes noise when the noise stops desktop work fine. It doesn't happen every day but it does happen. Is something wrong with HDD, Data, power cable, or my cabinet's power supply? Should I run scandisk or defragmentation on the disk.

    Read the article

  • one 16K random read I/O issues 2 scsi I/O (16K and 4K) requests in linux

    - by hiroyuki
    I noticed weird issue when benchmarking random read I/O for files in linux (2.6.18). The Benchmarking program is my own program and it simply keeps reading 16KB of a file from a random offset. I traced I/O behavior at system call level and scsi level by systemtap and I noticed that one 16KB sysread issues 2 scsi I/Os as following. SYSPREAD random(8472) 3, 0x16fc5200, 16384, 128137183232 SCSI random(8472) 0 1 0 0 start-sector: 226321183 size: 4096 bufflen 4096 FROM_DEVICE 1354354008068009 SCSI random(8472) 0 1 0 0 start-sector: 226323431 size: 16384 bufflen 16384 FROM_DEVICE 1354354008075927 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 21807710208 SCSI random(8472) 0 1 0 0 start-sector: 1889888935 size: 4096 bufflen 4096 FROM_DEVICE 1354354008085128 SCSI random(8472) 0 1 0 0 start-sector: 1889891823 size: 16384 bufflen 16384 FROM_DEVICE 1354354008097161 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 139365318656 SCSI random(8472) 0 1 0 0 start-sector: 254092663 size: 4096 bufflen 4096 FROM_DEVICE 1354354008100633 SCSI random(8472) 0 1 0 0 start-sector: 254094879 size: 16384 bufflen 16384 FROM_DEVICE 1354354008111723 SYSPREAD random(8472) 3, 0x16fc5200, 16384, 60304424960 SCSI random(8472) 0 1 0 0 start-sector: 58119807 size: 4096 bufflen 4096 FROM_DEVICE 1354354008120469 SCSI random(8472) 0 1 0 0 start-sector: 58125415 size: 16384 bufflen 16384 FROM_DEVICE 1354354008126343 As shown above, one 16KB pread issues 2 scsi I/Os. (I traced scsi io dispatching with probe scsi.iodispatching. Please ignore values except for start-sector and size.) One scsi I/O is 16KB I/O as requested from the application and it's OK. The thing is the other 4KB I/O which I don't know why linux issues that I/O. of course, I/O performance is degraded by the weired 4KB I/O and I am having trouble. I also use fio (famous I/O benchmark tool) and noticed the same issue, so it's not from the application. Does anybody know what is going on ? Any comments or advices are appreciated. Thanks

    Read the article

  • kernel warning disk error for command write - solaris svm

    - by help_me
    Recently this warning came up on my message logs, scsi: [ID 107833 kern.warning] WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd0): Oct 27 00:14:44 Error for Command: write(10) Error Level:Retryable Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Requested Block: 101515828 Error Block: 101515828 Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Vendor: SEAGATE Serial Number: 0441B9B5H Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Sense Key: Hardware Error Oct 27 00:14:44 scsi: [ID 107833 kern.notice] ASC: 0x19 (defect list error), ASCQ: 0x0, FRU: 0x2 This is showing signs of disk failing in my opinion. I have not seen the messages re-occurring. This is on a Solaris 9 Sparc system V240. The disks are managed by SVM and "metadb" is showing the flags as "a" Are there any tests or indications as to check/see if the disk is actually failing or was that error message initiated by something else. Thank you!

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • Recovery Harddisk for windows 7 (Details inside)

    - by iSumitG
    I want to create recovery media (DVD or HDD) for my Windows 7 running on my VAIO laptop. I noticed that my HDD is already having 13.51 GB partition which is labelled as "Recovery Partition" (not visible in My Computer but visible in Computer management tool in control panel). Can you please suggest me how to use this Recovery partition as a recovery media for my windows? I don't want to create DVDs as recovery media.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 281 282 283 284 285 286 287 288 289 290 291 292  | Next Page >