Search Results

Search found 10406 results on 417 pages for 'device'.

Page 29/417 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Messed up USB stick doesn't show in blkid

  - by Felix

  I was playing around with a USB stick (booting archlinux with qemu off of it and trying to perform an installation on the same stick at the same time -- brave, I know, but I was just messing around). Now, after failing to boot and install at the same time, it seems I have sort of messed up my stick. What I think happened is that I used cfdisk to wipe everything on it and create one big partition, but formatting it then failed, so now there's a big partition with no filesystem. Just to make it clear: I'm not worried for my stick, I know I can recover it at any point. What I find intriguing is that after plugging the stick into my computer (using Ubuntu), there's no (terminal) way to find out what block device (/dev/sdx) it has associated. The only way I could determine that was with GParted: But blkid shows the following: /dev/sda1: UUID="12F695CFF695B387" LABEL="System Reserved" TYPE="ntfs" /dev/sda2: UUID="A0BAA6EABAA6BC62" TYPE="ntfs" /dev/sdb1: UUID="546aec8b-9ad6-4571-b07a-adba63e25820" TYPE="ext4" /dev/sdb2: UUID="2a8b82d8-6c6e-4053-a446-bab970d93d7c" TYPE="swap" /dev/sdb3: UUID="7cbede7d-c930-4e59-9d1b-01f2d79bd092" TYPE="ext4" No trace of /dev/sdc. My question is: if I didn't have a graphical interface (to use GParted), how would I have known which block device is my stick?

  Read the article

• Can ping device from one computer and not the other

  - by Sean Duggan

  I've recently been assigned to work on a diagnostic program done in C++ which communicates with a piece of electronic equipment. Our normal scenario involves communicating via an RS232 interface, but I've been asked to make our program work over ethernet, source code having been done in Visual Basic. After much thrashing about trying to get the code to work and continuing to get 10049 Winsock errors when I tried to connect, I tried pinging the switch. From the computer the VB program is running on, I can see the switch via ping, nslookup, tracert, and pathping (I was going down the list of programs) and I can do this via URI or IP address. From my laptop, sending the same commands fails every time. They're both using the same network cable and the same USB-to-Ethernet device (I've been swapping them between tests) but one can see the switch and the other cannot. I'm working on the programming end, but the ping results makes me think that there might be a network issue stymieing me. wry grin I'm not much of a network guy, so I'm appealing to expert assistance. Both computers are running Windows XP if that helps. The connection is to an "IP-RS8" device which then connects to our VCU-C units. Each unit is accessible via URI or IP address on the desktop computer we usually have connected to the units (it's running the older VB program that I was asked to lift the networking code from). The connection is made via a USB-to-Ethernet adapter so as to leave the regular Ethernet port available for connecting to the company network. Hmm... come to think of it, I've probably been confusing the issue, talking about pinging "the switch" rather than indicating that it's the devices. My apologies. Communication is generally done with a DLL that uses Winsock functions to make queries for data from the VCU and then to receive. I'm failing when connecting. I haven't found anything on the firewall which should block these commands, but I'll keep poking. I don't know if it's potentially relevant, but on the desktop, the adapter maps to Local Area Connection 3 while on the laptop, it consistently maps to Local Area Connection 2. Currently reading up on DHCP. IPConfig /all results: Desktop Host Name . . . . . . . . . . . . : AMERDAEXXXXXX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Broadcom NetXtreme XYxx Gigabit Controller Physical Address. . . . . . . . . : YY-XX-YB-XX-XX-XX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XXX Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XY:XX:XX AM Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX axYYYYX USBX.Y to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XY.Y.Y.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XY.Y.Y.X DHCP Server . . . . . . . . . . . : XY.Y.Y.XY DNS Servers . . . . . . . . . . . : XY.Y.Y.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XY AM Lease Expires . . . . . . . . . . : Tuesday, August YX, XYXX XX:XY:XY AM Laptop Windows IP Configuration Host Name . . . . . . . . . . . . : AMERLAFYYXXYX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Intel(R) 82567LM Gigabit Network Connection Physical Address. . . . . . . . . : YY-XY-BY-DY-XB-YX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XY Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XX:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XX:XX:XX AM Ethernet adapter {XYXAAYXX-YEDY-XXYX-YYEX-BYXYXXYEEYEX}: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Nortel IPSECSHM Adapter - Packet Scheduler iniport Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-YY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : Y.Y.Y.Y Subnet Mask . . . . . . . . . . . : Y.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Leaf Networks Adapter: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Leaf Networks Adapter Physical Address. . . . . . . . . : YY-FF-FA-BC-YF-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : X.XYY.XY.XX Subnet Mask . . . . . . . . . . . : XXX.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : YY-FX-AX-YA-BY-CA Ethernet adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) WiFi Link 5300 AGN Physical Address. . . . . . . . . : YY-XX-YA-CX-FC-YE Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX ax88772 USB2.0 to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : XYX.XYY.X.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXX.Y Default Gateway . . . . . . . . . :

  Read the article

• Automatically creating volume partitions on boot

  - by Justin Meltzer

  I followed this guide: http://www.mongodb.org/display/DOCS/Amazon+EC2+Quickstart to set up Mongodb. It had me create a RAID 10 array out of the four devices on EBS. Then it had me create a physical volume, a volume group, and three logical volumes out of that RAID 10 array. Lastly it had me create ext4 filesystems out of the logical volumes and mount them. Now the quickstart guide had me put two things in place so that these steps would be replicated on reboot of the system. It had me add some instructions to the mdadm.conf file to automatically create the RAID 10 array, and it also had me add instructions to the fstab file to automatically mount the filesystem for each logical volume. However, the quickstart guide does not have anything for automatically creating the logical volumes from the RAID 10 array. I checked my system and see that each of the four devices are part of a RAID array: $ sudo mdadm -Q /dev/sdh1 /dev/sdh1: is not an md array /dev/sdh1: device 0 in 4 device unknown raid10 array. Use mdadm --examine for more detail. However, the filesystem is never created or mounted from fstab because it's trying to mount it from logical volumes that were never created (or so it seems). My question is, how can I automatically accomplish all the steps from the quickstart guide on a reboot of the system, and what config file do I need to add data to so that I can automatically create these volume partions after the RAID 10 is created but before the filesystem is mounted. Also I'm unsure whether fstab actually creates and mounts the filesystem or just mounts the filesystem.

  Read the article

• How to disable my laptop's defective keyboard?

  - by Kolink

  I have an Alienware M17x R2, and after a couple years of use I started having problems with the keyboard: Intermittently, and without warning or apparent cause (even if I'm not touching the computer), the S key (and more recently the D key) will start firing incessant signals until I hit the offending key. I've been using a USB keyboard, which is conveniently exactly the right size to fit over the built-in keyboard without touching any buttons. However, even as I type the defective keyboard will fire its stream of signals. I have contacted Dell about this, twice in fact. The first time, I was just bluntly told that they don't ship replacement keyboards. The second time I was told that they did, but they were out of stock and they would contact me when they were in stock again. They haven't contacted me since. I can't seem to work out which device to disable in the device manager. Here's a screenshot of what I have: None of the keyboard devices have "Disable" in their context menus, only "Uninstall"... so you'll understand if I'm hesitant to try anything myself. Any advice on how to fix this?

  Read the article

• Accessing the partitions on an VLM volume

  - by projix

  Suppose you have an LVM volume /dev/vg0/mylv. You have presented this as a virtual disk to a virtualised or emulated guest system. During installation the guest system sees it as /dev/sda and partitions it into /dev/sda{1,2,5,6} and completes the installation. Now at some point you need to access those filesystems from within the host system, without running the guest system. fdisk sees these partitions just fine: # fdisk -l /dev/vg0/mylv Device Boot Start End Blocks Id System /dev/vg0/mylv1 2048 684031 340992 83 Linux /dev/vg0/mylv2 686078 20969471 10141697 5 Extended /dev/vg0/mylv5 686080 8290303 3802112 83 Linux /dev/vg0/mylv6 8292352 11980799 1844224 83 Linux However, the devices such as /dev/vg0/mylv1 do not actually exist. I guess that because they're within an LV, the OS does not recognise this type of nesting by default. Is there any way I can prod Linux so that /dev/vg0/mylv1 or equivalent appears and thus becomes mountable within the host system? I understand that it's possible with qemu-nbd, and will use this if necessary. However, I was hoping for something more direct if possible, rather than simulating a network block device and attaching that.

  Read the article

• iPhone Device 3.1 SDK Breaks vertical alignment of UITableViewCellStyleValue1 textLabel

  - by user171089

  Can anyone provide an explanation for the following phenomenon? As of the iPhone Device 3.1 SDK, I've found that if a UITableViewCell is of style UITableViewCellStyleValue1 and its detailTextLabel.text is unassigned, then the textLabel does not display in the center of the cell as would be expected. One notable caveat is that this only happens for me when I'm testing on the Device – the iPhone Simulator 3.1 SDK displays the cells correctly. Also, this is not a problem when using the iPhone Device 3.0 SDK. Below is a simple UITableView subclass implementation that demonstrates the problem. @implementation BuggyTableViewController #pragma mark Table view methods // Customize the number of rows in the table view. - (NSInteger)tableView:(UITableView *)tableView numberOfRowsInSection:(NSInteger)section { return 3; } // Customize the appearance of table view cells. - (UITableViewCell *)tableView:(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *)indexPath { static NSString *CellIdentifier = @"Cell"; UITableViewCell *cell = [tableView dequeueReusableCellWithIdentifier:CellIdentifier]; if (cell == nil) { cell = [[[UITableViewCell alloc] initWithStyle:UITableViewCellStyleValue1 reuseIdentifier:CellIdentifier] autorelease]; } switch (indexPath.row) { case 0: cell.textLabel.text = @"detailTextLabel.text unassigned"; break; case 1: cell.textLabel.text = @"detailTextLabel.text = @\"\""; cell.detailTextLabel.text = @""; break; case 2: cell.textLabel.text = @"detailTextLabel.text = @\"A\""; cell.detailTextLabel.text = @"A"; break; default: break; } return cell; } @end

  Read the article

• trying to get the most accurate device location from GPS or Network in Android

  - by arc

  I am trying to determine the most accurate location of a device, in the shortest time possible. I am storing the data as a geopoint, and have it displayed on a mapview. The last time I activated the GPS on my device and let it get a location lock, i was approx 80 miles from where I am now. I have a location manager setup and a location listener. If I do this, I get NULL. myLocOverlay = new MyLocationOverlay(this, mapView); GeoPoint test = myLocOverlay.getMyLocation(); but in the next couple of lines; myLocOverlay.enableMyLocation(); mapView.getOverlays().add(myLocOverlay); With this, the overlay on the map shows the current location. It is using the Network provider, but is also attempting to get a GPS fix (it can't as I am indoors and no where near the top floor). If I construct the geopoint like this; if(lm.getLastKnownLocation("gps") != null) { test = new GeoPoint( (int) (lm.getLastKnownLocation("gps").getLatitude() * 1E6), (int) (lm.getLastKnownLocation("gps").getLongitude() * 1E6)); } else { if(lm.getLastKnownLocation("network") != null) { test = new GeoPoint( (int) (lm.getLastKnownLocation("network").getLatitude() * 1E6), (int) (lm.getLastKnownLocation("network").getLongitude() * 1E6)); } //bad things } Then I get confusing results. If I disable the devices GPS provider then the code moves onto the Network Provider and gives me a fairly accurate result. If I enable the GPS provider, then the geopoint comes back as the last place I allowed the device to get a GPS lock. I want to avoid the above results, and so was looking at using; GeoPoint test = myLocOverlay.getMyLocation(); BUT as I said above, I just get NULL from that. Short of getting the geopoints from both GPS and Network and then comparing them, and disregarding the GPS result if it is say 1 mile out of the Network location - i'm a bit stuck. why doesn't getMyLocation() work, shouldnt that return the GeoPoint of what myLocOverlay is showing on the mapview?

  Read the article

• blackberry maps do not show correct location on the device

  - by SWATI

  well frnds my code for maps works well and shows all pics and gradient paths very well on the simulator after simulating the gps ,but it does not works on the device.... The gps on device is working properly as google maps and other work related to gps are working perfectly fine my code if(GPS_Location.lati!=0.0 && GPS_Location.longi!=0.0) { User_latitude = ((GPS_Location.lati)*100000); User_longitude = ((GPS_Location.longi)*100000); User_La = String.valueOf(User_latitude).substring(0, String.valueOf(User_latitude).lastIndexOf('.')); User_Lo = String.valueOf(User_longitude).substring(0, String.valueOf(User_longitude).lastIndexOf('.')); if(param.equals("")) //for find business near me { document1 = "<location-document>" + "<location lon='"+User_Lo+"' lat='"+User_La+"' label='User' />"+ "<location lon='"+User_Lo+"' lat='"+User_La+"' label='"+"User"+"' />"+ "</location-document>"; } if(!param.equals("")) //for the directions { Business_latitude = Double.parseDouble(param.substring(0, param.lastIndexOf(','))); Business_longitude = Double.parseDouble(param.substring(param.lastIndexOf(',')+1,param.length())); Business_latitude = Business_latitude*100000; Business_longitude = Business_longitude*100000; Business_La = String.valueOf(Business_latitude).substring(0, String.valueOf(Business_latitude).lastIndexOf('.')); Business_Lo = String.valueOf(Business_longitude).substring(0, String.valueOf(Business_longitude).lastIndexOf('.')); document1 = "<location-document>" + "<GetRoute>"+ "<location lon='"+User_Lo+"' lat='"+User_La+"' label='User' />"+ "<location lon='"+Business_Lo+"' lat='"+Business_La+"' label='"+"User"+"' />"+ "</GetRoute>"+ "</location-document>"; } Invoke.invokeApplication(Invoke.APP_TYPE_MAPS,new MapsArguments(MapsArguments.ARG_LOCATION_DOCUMENT,document1)); } this code works on simulator but not fine on device. just points a pin indicating user and nothing else what to do????

  Read the article

• Static Libraries on iPhone device

  - by Akusete

  I have two projects, a Cocoa iPhone application and a static library which it uses. I've tested it successfully on the iPhone simulator, but when I try to deploy it to my iPhone device I get (symbol not found) link errors. If I remove the dependancy of the library the project builds/runs fine. I have made sure all the build settings are set to iPhoneOS not the simulator. Im sure its something simple, but has anyone run into similar problems moving from iPhone simulator to device? --EDIT: I have managed to create new projects (one for the application and one for the static library), and successfully get them to run on the iPhone or simulator. But I have a very strange problem... for each specific project I cannot get it working for BOTH the device and the simulator... I have double checked the build settings, made sure the libraries that are being references are for the matching build settings (I believe) but I cannot resolve these linking errors. I think I must be doing something very wrong... all the apple documentation says 'its super simple - one click' but this is giving me a lot of problems. This is probably something to do with xCode build settings, but I cannot seem to understand why selecting the different build platforms and rebuilding the libraries does not work.

  Read the article

• Blackberry application works in simulator but not device

  - by Kai

  I read some of the similar posts on this site that deal with what seems to be the same issue and the responses didn't really seem to clarify things for me. My application works fine in the simulator. I believe I'm on Bold 9000 with OS 4.6. The app is signed. My app makes an HTTP call via 3G to fetch an XML result. type is application/xhtml+xml. In the device, it gives no error. it makes no visual sign of error. I tell the try catch to print the results to the screen and I get nothing. HttpConnection was taken right out of the demos and works fine in sim. Since it gives no error, I begin to reflect back on things I recall reading back when the project began. deviceside=true? Something like that? My request is simply HttpConnection connection = (HttpConnection)Connector.open(url); where url is just a standard url, no get vars. Based on the amount of time I see the connection arrows in the corner of the screen, I assume the app is launching the initial communication to my server, then either getting a bad result, or it gets results and the persistent store is not functioning as expected. I have no idea where to begin with this. Posting code would be ridiculous since it would be basically my whole app. I guess my question is if anyone knows of any major differences with device versus simulator that could cause something like http connection or persistent store to fail? A build setting? An OS restriction? Any standard procedure I may have just not known about that everyone should do before beginning device testing? Thanks

  Read the article

• WCF Async callback setup for polled device

  - by Mark Pim

  I have a WCF service setup to control a USB fingerprint reader from our .Net applications. This works fine and I can ask it to enroll users and so on. The reader allows identification (it tells you that a particular user has presented their finger, as opposed to asking it to verify that a particular user's finger is present), but the device must be constantly polled while in identification mode for its status - when a user is detected the status changes. What I want is for an interested application to notify the service that it wants to know when a user is identified, and provide a callback that gets triggered when this happens. The WCF service will return immediately and spawn a thread in the background to continuously poll the device. This polling could go on for hours at a time if no one tries to log in. What's the best way to acheive this? My service contract is currently defined as follows: [ServiceContract (CallbackContract=typeof(IBiometricCallback))] public interface IBiometricWcfService { ... [OperationContract (IsOneWay = true)] void BeginIdentification(); ... } public interface IBiometricCallback { ... [OperationContract(IsOneWay = true)] void IdentificationFinished(int aUserId, string aMessage, bool aSuccess); ... } In my BeginIdentification() method can I easily spawn a worker thread to poll the device, or is it easier to make the WCF service asynchronous?

  Read the article

• How to get rid of a stubborn 'removed' device in mdadm

  - by T.J. Crowder

  One of my server's drives failed and so I removed the failed drive from all three relevant arrays, had the drive swapped out, and then added the new drive to the arrays. Two of the arrays worked perfectly. The third added the drive back as a spare, and there's an odd "removed" entry in the mdadm details. I tried both mdadm /dev/md2 --remove failed and mdadm /dev/md2 --remove detached as suggested here and here, neither of which complained, but neither of which had any effect, either. Does anyone know how I can get rid of that entry and get the drive added back properly? (Ideally without resyncing a third time, I've already had to do it twice and it takes hours. But if that's what it takes, that's what it takes.) The new drive is /dev/sda, the relevant partition is /dev/sda3. Here's the detail on the array: # mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Wed Oct 26 12:27:49 2011 Raid Level : raid1 Array Size : 729952192 (696.14 GiB 747.47 GB) Used Dev Size : 729952192 (696.14 GiB 747.47 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 12 17:48:53 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 UUID : 2fdbf68c:d572d905:776c2c25:004bd7b2 (local to host blah) Events : 0.34665 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - spare /dev/sda3 If it's relevant, it's a 64-bit server. It normally runs Ubuntu, but right now I'm in the data centre's "rescue" OS, which is Debian 7 (wheezy). The "removed" entry was there the last time I was in Ubuntu (it won't, currently, boot from the disk), so I don't think that's not some Ubuntu/Debian conflict (and they are, of course, closely related). Update: Having done extensive tests with test devices on a local machine, I'm just plain getting anomalous behavior from mdadm with this array. For instance, with /dev/sda3 removed from the array again, I did this: mdadm /dev/md2 --grow --force --raid-devices=1 And that got rid of the "removed" device, leaving me just with /dev/sdb3. Then I nuked /dev/sda3 (wrote a file system to it, so it didn't have the raid fs anymore), then: mdadm /dev/md2 --grow --raid-devices=2 ...which gave me an array with /dev/sdb3 in slot 0 and "removed" in slot 1 as you'd expect. Then mdadm /dev/md2 --add /dev/sda3 ...added it — as a spare again. (Another 3.5 hours down the drain.) So with the rebuilt spare in the array, given that mdadm's man page says RAID-DEVICES CHANGES ... When the number of devices is increased, any hot spares that are present will be activated immediately. ...I grew the array to three devices, to try to activate the "spare": mdadm /dev/md2 --grow --raid-devices=3 What did I get? Two "removed" devices, and the spare. And yet when I do this with a test array, I don't get this behavior. So I nuked /dev/sda3 again, used it to create a brand-new array, and am copying the data from the old array to the new one: rsync -r -t -v --exclude 'lost+found' --progress /mnt/oldarray/* /mnt/newarray This will, of course, take hours. Hopefully when I'm done, I can stop the old array entirely, nuke /dev/sdb3, and add it to the new array. Hopefully, it won't get added as a spare!

  Read the article

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• Java ME SDK 3.2 is now live

  - by SungmoonCho

  Hi everyone, It has been a while since we released the last version. We have been very busy integrating new features and making lots of usability improvements into this new version. Datasheet is available here. Please visit Java ME SDK 3.2 download page to get the latest and best version yet! Some of the new features in this version are described below. Embedded Application SupportOracle Java ME SDK 3.2 now supports the new Oracle® Java ME Embedded. This includes support for JSR 228, the Information Module Profile-Next Generation API (IMP-NG). You can test and debug applications either on the built-in device emulators or on your device. Memory MonitorThe Memory Monitor shows memory use as an application runs. It displays a dynamic detailed listing of the memory usage per object in table form, and a graphical representation of the memory use over time. Eclipse IDE supportOracle Java ME SDK 3.2 now officially supports Eclipse IDE. Once you install the Java ME SDK plugins on Eclipse, you can start developing, debugging, and profiling your mobile or embedded application. Skin CreatorWith the Custom Device Skin Creator, you can create your own skins. The appearance of the custom skins is generic, but the functionality can be tailored to your own specifications.  Here are the release highlights. Implementation and support for the new Oracle® Java Wireless Client 3.2 runtime and the Oracle® Java ME Embedded runtime. The AMS in the CLDC emulators has a new look and new functionality (Install Application, Manage Certificate Authorities and Output Console). Support for JSR 228, the Information Module Profile-Next Generation API (IMP-NG). The IMP-NG platform is implemented as a subset of CLDC. Support includes: A new emulator for headless devices. Javadocs for the following Oracle APIs: Device Access API, Logging API, AMS API, and AccessPoint API. New demos for IMP-NG features can be run on the emulator or on a real device running the Oracle® Java ME Embedded runtime. New Custom Device Skin Creator. This tool provides a way to create and manage custom emulator skins. The skin appearance is generic, but the functionality, such as the JSRs supported or the device properties, are up to you. This utility only supported in NetBeans. Eclipse plugin for CLDC/MIDP. For the first time Oracle Java ME SDK is available as an Eclipse plugin. The Eclipse version does not support CDC, the Memory Monitor, and the Custom Device Skin Creator in this release. All Java ME tools are implemented as NetBeans plugins. As of the plugin integrates Java ME utilities into the standard NetBeans menus. Tools > Java ME menu is the place to launch Java ME utilities, including the new Skin Creator. Profile > Java ME is the place to work with the Network Monitor and the Memory Monitor. Use the standard NetBeans tools for debugging. Profiling, Network monitoring, and Memory monitoring are integrated with the NetBeans profiling tools. New network monitoring protocols are supported in this release: WMA, SIP, Bluetooth and OBEX, SATSA APDU and JCRMI, and server sockets. Java ME SDK Update Center. Oracle Java ME SDK can be updated or extended by new components. The Update Center can download, install, and uninstall plugins specific to the Java ME SDK. A plugin consists of runtime components and skins. Bug fixes and enhancements. This version comes with a few known problems. All of them have workarounds, so I hope you don't get stuck in these issues when you are using the product. It you cannot watch static variables during an Eclipse debugging session, and sometimes the Variable view cannot show data. In the source code, move the mouse over the required variable to inspect the variable value. A real device shown in the Device Selector is deleted from the Device Manager, yet it still appears. Kill the device manager in the system tray, and relaunch it. Then you will see the device removed from the list. On-device profiling does not work on a device. CPU profiling, networking monitoring, and memory monitoring do not work on the device, since the device runtime does not yet support it. Please do the profiling with your emulator first, and then test your application on the device. In the Device Selector, using Clean Database on real external device causes a null pointer exception. External devices do not have a database recognized by the SDK, so you can disregard this exception message. Suspending the Emulator during a Memory Monitor session hangs the emulator. Do not use the Suspend option (F5) while the Memory Monitor is running. If the emulator is hung, open the Windows task manager and stop the emulator process (javaw). To switch to another application while the Memory Monitor is running, choose Application > AMS Home (F4), and select a different application. Please let us know how we can improve it even better, by sending us your feedback. -Java ME SDK Team

  Read the article

• How do I set up live audio streams to a DLNA compliant device?

  - by Takkat

  Is there a way to stream the live output of the soundcard from our 12.04.1 LTS amd64 desktop to a DLNA-compliant external device in our network? Selecting media content in shared directories using Rygel, miniDLNA, and uShare is always fine - but so far we completely failed to get a live audio stream to a client via DLNA. Pulseaudio claims to have a DLNA/UPnP media server that together with Rygel is supposed to do just this. But we were unable to get it running. We followed the steps outlined in live.gnome.org, this answer here, and also in another similar guide. As soon as we select the local audio device, or our GST-Launch stream in the DLNA client Rygel displays the following message and the client states it reached the end of the playlist: (rygel:7380): Rygel-WARNING **: rygel-http-request.vala:97: Invalid seek request This is how we configured GST-Launch in rygel.conf: [GstLaunch] enabled=true launch-items=mypulseaudiosink mypulseaudiosink-title=Audio on @HOSTNAME@ mypulseaudiosink-mime=audio/x-wav mypulseaudiosink-launch=pulsesrc device=<device> ! wavpackenc For <device> we tried with the default sink name, this name appended with .monitor, and in addition with upnp-sink and upnp.monitor that was created when we selected DLNA media server from paprefs. We also tried to encode using lamemp3enc with no luck. These are our pulseaudio modules: http://paste.ubuntu.com/1202913/ These are our sinks: http://paste.ubuntu.com/1202916/ Did we miss any other additional configuration needed to get this running? Are there any other alternatives for sending the audio of our soundcard as live stream to a DLNA client?

  Read the article

• How do you reset a USB device from the command line?

  - by Casey

  Is it possible to reset the connection of a USB device, without physically disconnecting/connecting from the PC? Specifically, my device is a digital camera. I'm using gphoto2, but lately I get "device read errors", so I'd like to try to do a software-reset of the connection. From what I can tell, there are no kernel modules being loaded for the camera. The only one that looks related is usbhid.

  Read the article

• Wacom board not detected

  - by Christer

  Board is not detected by the system settings, ubuntu 11.10 uname -r 3.0.0-13-generic-pae Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c512 Logitech, Inc. LX-700 Cordless Desktop Receiver Bus 002 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Bus 003 Device 003: ID 056a:00df Wacom Co., Ltd Bus 002 Device 004: ID 03f0:0601 Hewlett-Packard ScanJet 6300c Bus 002 Device 005: ID 067b:2305 Prolific Technology, Inc. PL2305 Parallel Port Bus 002 Device 006: ID 0409:0056 NEC Corp. lsmod | grep wacom try to autogen driver input-wacom-0.11.1 from git, but fails with configure: WARNING: kernel version 3.0.0-13-generic-pae not supported Anyone have a solution ?

  Read the article

• How to auto-scan any plugged in usb storage device with clamav?

  - by ossi

  I'd like to do an automatic virus scan on any plugged in usb device using ClamAV. I'm using Ubuntu 12.04. The closest thing I found was: Run clamav on mount of flashdrive How to run a shell script when a new USB storage device is detected? The first one is not working for me and the second one seems to target a known device. Is there a tutorial around I've missed? Or can I get some help with udev rules that apply to any usb storage device added? Currently nothing seems to do anything.

  Read the article

• Now that Device Central is dead, how can I test my Flash Lite applications?

  - by Kirby

  I'm trying to use Flash Lite to make a simple game for my girlfriend, who only has a Nokia 5530, but I just realized in CS6 Adobe killed Device Central, so there's no way for me to test it without the device (and it's supposed to be a surprise). Is there any other way for me to test it? I know I can just export the movie and use Flash Player, but Device Central allowed me to test drag and drop and memory/processor usage for example... tl;dr, is there an alternative to Device Central for testing Flash Lite in older devices?

  Read the article

• Multi Monitor Setup Problems

  - by Shamballa

  I have Ubuntu 10.04 LTS - the Lucid Lynx. I have until recently been using a nVida Graphics card (NVIDIA GeForce 9800 GT) with two monitors attached, this all worked fine and dandy. A couple of days ago I bought two new identical LCD monitors for a multi monitor setup and two ATI graphics cards (ATI Sapphire Radeon HD5450). NOTE *All monitors work fine in Windows XP, 2k, Vista and 7 After I had booted into Ubuntu only one display came on, that I kind of expected anyway, then I removed the driver for the nVidia card and downloaded the ATI version which gave me the ATI Catalyst Control Center - in that only two of the displays were showing the third was disabled and showing unknown driver. I enabled the third monitor that stated "Unkown Driver" and had to reboot, upon reboot none of the displays work. I restarted and booted up into recovery mode and from now that is only what I can get into using a failsafe driver. It seems according to the log that a server is already active for Display 0 and I have to remove /tmp/.X0-lock and start again. This is what the log file is saying: Fatal Server Error Server is already active for display 0 if this server is no longer running, remove /tmp/.X0-lock and start again. (WW) xf86 closeconsole: KDSETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETSTATE failed: Bad file descriptor ddxSigGiveUp: closing log I have tried looking at my xorg.config file but unfortunately I have not really got a clue as to how it "should" be - I have tried regenerating it using this command from a terminal: sudo dpkg-reconfigure -phigh xserver-xorg but that had no effect so I am currently stuck in failsafe driver mode but two monitors are active but are mirroring each other. I hope that this is not to long - looking back I have been going on a bit! but I am just trying to explain as much as I can... I have asked this on Linuxquestions but nobody seems to know either or at least I have not had any responses. Could some kind soul please help explain what I can do from here? I would be eternally grateful. Chris * Update * Removing xorg.conf does nothing other than allowing me to use only two monitors - using the command: sudo aticonfig --initial generates the xorg.conf file below: but does not work either - I just get two monitors... Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I have tried using this command from a thread on the Ubuntu Forums with a question similar to mine: sudo aticonfig --initial=dual-head --adapter=all Generated xorg.conf file Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[0]-1" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-1" Screen "aticonfig-Screen[1]-1" RightOf "aticonfig-Screen[1]-0" EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]-1" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:2:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-1" Driver "fglrx" BusID "PCI:2:0:0" Screen 1 EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]-1" Device "aticonfig-Device[0]-1" Monitor "aticonfig-Monitor[0]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-1" Device "aticonfig-Device[1]-1" Monitor "aticonfig-Monitor[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection This upon reboot renders ALL monitors blank and I have to go into recovery mode and use a failsafe driver. This is so much harder than I thought it would be, I don't think Ubuntu likes ATI for multi (3) monitors or maybe the other way around. Can anyone help still?

  Read the article

• How do you reset a USB device from the command line?

  - by Casey

  Is it possible to reset the connection of a USB device, without physically disconnecting/connecting from the PC? Specifically, my device is a digital camera. I'm using gphoto2, but lately I get "device read errors", so I'd like to try to do a software-reset of the connection. From what I can tell, there are no kernel modules being loaded for the camera. The only one that looks related is usbhid.

  Read the article

• Android ACTION_BOOT_COMPLETED called everytime?

  - by user3976029

  I am trying to write a code in Android , to create a condition during booting but my condition satisfies everytime ( during booting as well as during running of the device also). I am trying to do is , to execute the condition during the booting only. My Code : MainActivity.java package com.example.bootingtest; import android.os.Bundle; import android.widget.Toast; import android.app.Activity; import android.content.Intent; public class MainActivity extends Activity { @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); if (Intent.ACTION_BOOT_COMPLETED!=null) { Toast.makeText(getApplicationContext(), "Device is booting ...", Toast.LENGTH_LONG).show(); } } } I have given manifest permission . <uses-permission android:name="android.permission.RECEIVE_BOOT_COMPLETED" /> I want to execute this condition only during booting or device start-up but this condition satisfies every time , whenever i open the app. Please suggest me , how can i run the condition only during the device booting or start-up. Please help me out.

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• What is /dev/md2?

  - by Dougal

  Specifically, what might "A Fail event had been detected on md device /dev/md2." ramify? (in an email from Plesk control panel's "Logwatch" BTW)

  Read the article

• Tomcat app doesn't work with Fingerprint Reader in Windows 7

  - by IgniFerroque

  I've got a tomcat webapp that uses a fingerprint reader. It works fine under Windows XP and Windows 7 if you double click on tomcat.exe. It doesn't work on Windows 7 if you run tomcat as a service. I imagine that when run as a service the process doesn't have the required permissions to talk to the device. I've tried running it as an administrator and verified that it's doing so with Process Explorer. What else should I check?

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >