Search Results

Search found 1074 results on 43 pages for 'late'.

Page 29/43 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Looking for recommendations on OCR problem - tabular numeric data

  - by ldigas

  I have 20 pages of experiment measurement data which I need to digitalize. The results are in tabular form, scanned in 600 dpi resolution, and as far as scans go, they came up pretty clean and readable. For an example of how it looks see here (but beware: it is a rather big scan; about 5Mb; no problem for any broadband connection, but dialups should approach with caution!) ... and I need it finished by sunday afternoon (:-o) <-- smiley in a state of panic (then why did't you start sooner?)... yea, yeah ... I know ... but, it came up late, and I wasn't thinking I was gonna need this data also. So, I'm looking for recommendations. I haven't much experience with OCR programs, save scanning a page or two of pure text, but just to mention, I haven't the wish also to test out every OCR program out there. So this isn't a "name your OCR favourite". What I'm looking is advice from someone who's done something like that, and his/hers experience on what would be the best way to undertake. I need the data in txt form but since it will have to be checked (by drawing it, and just simply watching whether some points "jump out") I'll probably be entering it in Excel at first.

  Read the article

• How to point a subdomain to local server with dynamic IP

  - by jlego

  I see there are many related questions to this one, however the answers given seem to be a little vague for a novice like me. I've got a dedicated LAMP stack running Fedora 16 locally on my home network. Everything works fine internally. I can access the Apache server from other machines on the network using the internal IP in a browser. I'm using the stack for a local file server as well as a development environment for websites. There are a couple of reasons why I would like the development sites hosted on the machine to be available publicly. 1.) I use a CMS that has paid add-ons which allows you to assign the paid license to a domain. I can't develop with paid add-ons on the closed dev server. 2.) I would occasionally like for clients to be able to view the site dev at late stages before it goes live. I have a domain (foo.com, and I want to point a *sub*domain (dev.foo.com) to the local server. I know this is best accomplished with a Static IP, however my IP from my ISP is Dynamic and I don't think there is any way to change that. From what I have read, services like ZoneEdit & DynDNS are supposed to be able to accomplish this, but I have tried both and found it very confusing. Also the server is behind a router and I have also read that you need to set up DDNS(?) in your router, that many routers have presets for these services, and I've found that DynDNS is the only one my router seems to support.

  Read the article

• Annoying trackpad freeze on MacBook [solved]

  - by Hafthor

  NOTE: Question marked answered because it was forced after being put up for bounty. Actual solution was to have Apple repair it. Trackpad usually works, but sometimes stops responding for around 5 seconds and then suddenly starts working again. Seems to happen when I switch between typing and moving + button-clicking and also when I do a lot of double-clicking. Tried turning off the "Ignore accidental trackpad input". Apple replaced the keyboard/mouse under warranty. Problem remains. Any ideas? Edit: White non-unibody Late-2008 13" MacBook - fully up-to-date OS. Doesn't seem to matter if it is plugged in or not. Edit: Updated to Snow Leopard - seems to have made it worse. Edit: Applying even a little pressure to the left palm rest creates this condition. Apple replaced the top case again and this time it seems to have fixed it. Although, it looks like they may have added a spacer on the left palm rest to "fix" it.

  Read the article

• Can I disable this Windows (XP) Security Warning?

  - by FumbleFingers

  I recently reformatted my hard drive and reinstalled Windows XP (I know I'll have to take the plunge and commit to Win8 "real soon, now", but I'm just not quite ready for the upheaval yet! :) I used to use WinRar (and later, when I got fed up with the "nag" messages, 7-Zip), but I haven't installed either of them in my new configuration, so I must be using the built-in XP facility when I open *.zip files. For years, I've been opening downloaded *.zip archives, and using "drag & drop" to copy to a File Explorer window open on the folder where I want the files to end up (usually, My Documents\Downloads). But now I find that when I "drop" the file(s), I get a pop-up Windows Security Warning saying Are you sure you want to copy or move files to this folder? You should only move or copy files from locations that you trust Can anyone explain why I'm getting this message, and is there any (reasonably easy, please! :) way to suppress it? Since I've already put the *.zip file on my computer, it seems a bit late to ask if I trust it. (Thus far, the files in question have always been plain text, so it's not a matter of dodgy programs, etc.) Apologies for the low quality image - I don't have the appropriate tools or knowledge to do any better, and it doesn't help that my "PrtScr" screen capture has included what would have been on my second monitor (TV) if it had been turned on. If you can't read it, trust me - I have copied the text verbatim.

  Read the article

• Is browser based wireless authentication secure?

  - by johnnyb10

  Our wireless network previously used a preshared WPA/WPA2 key for guest access, which allows them access to the Internet. (Our employee access uses 802.1x authentication). We just had a wireless consultant come in to fix various wireless issues we had; one of the things he wound up doing was changing our guest access to HTML-based instead of the preshared key. So now that guest SSID is open (instead of using WPA) and users are presented with a browser-based login screen before they can get on the Internet. My question is: Is this an acceptable method from a security standpoint? I would assume that having an open network is necessarily a bad idea, but the consultant said that the traffic is still using PEAP, so it's secure. I didn't get a chance to question him further on this because we ran late and a bunch of other things came up. Please let me know what you think about the advantages/disadvantages of using HTML-based wireless authentication as opposed to using a preshared WPA key. Thanks...

  Read the article

• Blue screen error code 1000008e

  - by Kas

  I'm getting blue screens, mostly when trying to boot a program that required a lot of memory (games, photo editing software.) So far I've only managed to catch one set of error codes: BCCode: 1000008e BCP1: C0000005 BCP2: ADA393BA BCP3: E9BCEBC4 BCP4: 00000000 OS Version: 6_0_6002 Service Pack: 2_0 Product: 768_1 It's on a Sony VAIO Laptop VGN FW-41E, Vista OS service pack 2. Besides these codes it lists two 'temporary' files that were related with this crash: ...AppData\Local\Temp\WER-134925-0.sysdata.xml ...AppData\Local\Temp\WERDA66.tmp.version.txt When I googled these files some site said it was linked to a worm called 'yodo', but virus scans don't return any results (hitman pro, malware bytes, avast antivirus all turn up empty). Upon further searching about this yodo worm, I came across security stronghold where someone posted they had acquired this worm when downloading access and excel templates. Now, I actually did download templates for the same programs, they might have been the same, they may be related or I might be grasping at straws here. I have not noticed any issues other in performance as of late, just BSOD's when I start software that requires some memory, but I never had issues with these exact same programs before. Help and/or hints are required on how to actually figure out what's the root of this BSOD issue and how can I fix it. Do you reckon it's actually a virus? What program should be able to remove YODO worm stuff?

  Read the article

• How come my Intel 520 180GB SSD performs extremely poorly?

  - by Willem

  I recently installed a new Intel 520 series 180GB SSD in my brand new MacBook Pro. The system is as follows: Model: MacBook Pro 15-inch, Late 2011 (MacBookPro8,2) Processor: 2.4 GHz Intel Core i7 Memory: 16 GB 1333 MHz DDR3 Graphics: AMD Radeon HD 6770M 1024 MB Software: Mac OS X Lion 10.7.3 Main Drive Bay: Intel 520-series 180GB SATA-3 (6GB/s negotiated link) SSD (Firmware: 400i) [80GB free] Optical Bay: Toshiba 5400 RPM 750GB SATA-2 HDD Trim: Enabled (according to Trim Enabler App) And here are the speeds I'm getting: Read: 412 MB/s Write: 186 MB/s What have I done wrong? Results expected: Read/write both 500MB/s I have seen benchmarks with lesser SSD:s (SATA-2 even) outperform my write-speeds by far. Also, Intel 520 SSD:s are supposed to be the top class of SSD:s. Trim Enabler report: This looks a bit odd compared to screenshots from their site: These is the defined S.M.A.R.T attributes (taken from Intel): And here are my S.M.A.R.T attributes read using smartctl tool from smartmontools: They don't seem very compatible. I'm going to try and look for a S.M.A.R.T attributes reader tool for OS X which might support Intel 520 series.

  Read the article

• How to Re-install an App that Shows up in the Appstore as 'Update' Instead of 'Buy App'

  - by Craig Reville

  So long story short: I dropped the wrong app into 'clean my mac' and I hit 'cancel' but it was too late by that point. I rebooted and appstore said it had an update, when I opened appstore it was showing an update for the app I just uninstalled. I tried clicking 'update' but it gives me an error saying it's unable to install after 'downloading'. When I try to go into 'purchased apps' it shows the app as uninstalled so I click 'install' and I get an error saying it's already installed. I'm running Lion OS X, latest version, updated, mac book pro is only a few months old. I tried searching through the entire system to remove all traces of the app, after rebooting appstore no longer shows the app and no longer shows the update but on the apps page it still says 'Update'. I tried reinstalling the app from desktop OUT of the appstore and again says the app is 'already installed'. So after reading more about lion I found an article that spoke about 'BundleID' being the thing that tells appstore what's installed and needing updating however I can't find the location of where the BundleID would be. Any thoughts? I've tried CCleaner, AppCleaner etc and none of them show the app, mainly because it is uninstalled. Update I've spoken to Apple Support who confirmed that there is a file in the system that connects separately to tell the system if there are updates available however they declined to inform me of any further details. Apple also referred me from technical support to iTunes App Store opposed to Mac App Store support and from there I have been referred to AppleCare who are currently 'investigating' this issue. Hopefully there will be a fix that's simple to implement for people having similar issues, this appears to be a more common issue than I previously thought.

  Read the article

• Looking for Remote Control that works with everything (even Windows 7 Media Center)

  - by T Reddy

  Using my Google-Fu, it seems that the most basic of things one gets with any DVR is the remote control. Had I known it would be difficult just to get a consumer IR receiver for Windows 7 I may not have bothered to build an HTPC. But too late, I already have the HTPC ready to go (minus the CETON card...) So I'm moving away from TiVo, I hate paying the monthly fees and my box is ancient. I'm looking for these solutions to my HTCP setup...I want to: Switch audio from HDMI to SPDIF via the remote control (i.e., switch from TV to Receiver) (as a side note, the built-in audio on the mobo has software to do this). Pressing the volume button on the remote will always change the TV's volume (or the Receiver's if possible) and NOT the PC's volume. The remote/receiver works well around 25 feet. Bonus if the IR Receiver can work with my existing TiVo remote (or other remotes laying around the house) I read a review of the Bluetooth TiVo remote...it sounds promising...but I'm not sure if it is great for Windows 7 HTPC?

  Read the article

• Subdocument in Word won't save

  - by ChrisW

  Because I know Word has a history of not liking very large documents (my supervisor specifically told me not to use LaTeX... grr), I decided to learn the Master document / subdocument feature of Word when writing my PhD thesis. I have the title page / table of contents etc in the master document, and each chapter as a separate document. However, when I save the master document, it appears to save all the chapter documents apart from one (Chapter 4), for which it brings up the Save Document dialog box, helpfully with "Chapter4.docx" in the "Save as" box (n.b. Chpater4.dox is not open). Clicking save does nothing, and doesn't make the dialog box go away. Saving as a different document means that my changes aren't reflected in the same document. There must be some reason Word doesn't like this particular document but I've got no idea why - there's nothing special in it that isn't in any of the other chapters. I have tried closing all documents, renaming Chapter4.docx, opening the master document, expanding all documents, OKing the warning that Chapter4.dox does not exist, and inserting the 'new' document, but even when I save the master document it still won't save the new Chapter4 document. If anyone knows any reason why Word is acting like this (or if I'm doing anything stupid), I'll be eternally grateful (p.s. sorry for the long rambling message. It's late; I've been working on my PhD 4.5 years, I really really want to throw this computer out the window, and I hope people are kind enough not to downvote this question because of it's rambling nature!) Update With Word closed, I've tried to delete Chapter4.docx (having made a backup!) - but I get a warning that it can't be deleted because it's open in Microsoft Word... these files are on a network drive and the same problems are happening on 2 different computers. I could login to the filestore through ssh and force the file to be deleted, but I'm curious to know why this is happening!

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• git : The remote end hung up unexpectedly - too many simultaneous users?

  - by Pritam Barhate

  I asked this first on StackOverflow and I was suggested that I should ask it here: We have a self hosted git server (Gitolite) on a VPS account (CPU:2.68GHz RAM:1824MB). This same VPS is also used to publish our underdevelopment web apps for client demos. (Very little traffic). so the main use of the server is as a Git Server Only. This git server is accessed by a team of 30-40 people for various projects. Our problem is that during the day when 6-7 people are trying to access the server (sometimes same repo) we get frequent error message: ssh: connect to host xxx.xxx.xx.xx port 22: Bad file number fatal: The remote end hung up unexpectedly After trying for 10-15 minutes it generally succeeds. During early mornings and late nights when there are only 1-2 people, git commands work with 100% success rate. Also I would like to note that if I access the other file hosted on the server through HTTP it works fine. I found a couple of questions on StackOverflow and on other sites regarding this. But most of the people point towards SSH key set up or conflicts between Msysgit and Cygns SSH. However I don't think this is the problem in our case as we get this behavior on Windows (using msysgit only) as well as Mac Machines. Also if it was SSH configuration issue then it shouldn't work at all. But in our case it works after 10-15 minutes. I think in our case it might be too many simultaneous connections to same server (or same repo) or something like that. Does there exists a setting or a conf file that needs to modified to solve this problem? Please help me solve this problem or point me in the right direction. Thanks in advance. Pritam.

  Read the article

• Hibernate between OS X and Bootcamp Win 7

  - by Willem

  Wouldn't it be great if someone wrote a guide or an app which allowed you to switch instantly between OS X and Windows using Hibernate in both OS:s? Windows 7 already has an option "Hibernate" which allows you to boot back to your OS X partition, but OS X does not exactly offer the same. However, there are possibilities here. It seems that the recent Mac's have 3 different kinds of sleeping mode: Sleep: Low power consumption, RAM still active. Legacy Safe Sleep: No power consumption(?), writes RAM to disk and shuts down (is this the same as Hibernate?) Safe Sleep: Writes RAM to disk and enters sleep mode. If battery level drops too low it goes into Hibernate (is this Hibernate the same as #2 in this list? This is the Hibernate I will be referring to int he rest of this post) It seems that I am unable to force my MacBook Pro (Late 2011) OS X 10.7.3 into a true hibernate using either command line or apps that are supposed to do this. I believe the Mac should show that white loading bar whilst waking up if it was truly put into hibernate (which it does not). But I can get this white bar to show by letting my battery level drop to 0% so there is obviously a system function for it (obviously, duh! :). When Win 7 goes into hibernate it shuts down completely and you can then boot into OS X on startup. On OS X however, hibernate forces you to wake up into OS X. Can you hack this so that you're allowed to select boot partition after OS X hibernates? Would it be possible to use the true hibernate system functionalities of Win 7 and OS X to create a kind of instant switching between the two? Imagine this on a quick SATA-3 SSD like my 180GB Intel 520. Thanks / Willem

  Read the article

• mod_fcgi in virtualmin: graceful kill fail, sending SIGKILL?

  - by mgjk

  Yesterday around 1am, our server ground to a crawl. This doesn't happen often, but I'm trying to get to the bottom of it. There is no unusual traffic volume, no unusual processes running, just all of the sudden the server started killing fcgid processes. [Thu Aug 02 01:17:32 2012] [warn] mod_fcgid: process 26460 graceful kill fail, sending SIGKILL ... for as many fcgid processes as we have... CPU idle fell to 0% and I/O seemed to take up most of the load. The issue lasted about 5 minutes. I suspect there was some swap activity, although I'm not sure if it was due to killed processes being swapped in to die, or if it was because some process ramped up memory usage faster than my process watching scripts can see them. The oom-killer wasn't triggered (at least it's not logged), so I think this was Apache for some reason restarting the processes. This is not regular, and nothing obvious appears in cron. Is there a normal Apache process which might cause this? We run dozens of different sites, and it was late at night, so volume was very, very low. (maybe 200 requests in a 10 minute period).

  Read the article

• Thunderbird 11.0.1 and Lightning 1.3: How do I propose a different time for a meeting?

  - by seaao

  This all happens on my x64 Linux workstation btw. tl;dr: My colleague invited some people and me for a meeting. The meeting was scheduled a week to late. I -wrongfully- accepted. How do I propose a new time? To explain a bit more in detail: I received a meeting request in my mailbox. Thunderbird is so nice to let me accept or reject it, and after I click the button to accept, it is directly added to my calendar. But when I double click on the meeting to edit it, I get a function-wise scaled-down version of the meeting: The only settings I can alter are whether I want reminders, and if I go at all. Trying to drag it to another day doesn't work either: My calendar behaves like read-only (which it isn't btw). There are several questions (without answer...) to be found on Stack Overflow and on the Thunderbird knowledge base about using lightning. But I get the idea that I'm one of the few who won't comply with the team even before the meeting is started. My googling revealed no bugs or feature requests in the direction I'm thinking. A link to an explanation how to achieve this, or another perspective about how to reach the desired goal (meeting with my colleagues and me) would be mostly welcome!

  Read the article

• Does anyone know how to "tcpdump" traffic decrypted by Mallory MITM? [migrated]

  - by chriv

  I'm looking for some help in capturing network traffic that I can analyze in Wireshare (or other tools). The tool I'm using is mallory. If anyone is familiar with mallory, I could use some help. I've got it configured and running correctly, but I don't know how to get the output that I want. The setup is on my private network. I have a VM (running Ubuntu 12.04 - precise) with two NICs: eth0 is on my "real" network eth1 is only on my "fake" network, and is using dnsmasq (for DNS and DHCP for other devices on the "fake" network) Effectively eth0 is the "WAN" on my VM, and eth1 is the "LAN" on my VM. I've setup mallory and iptables to intercept, decrypt, encrypt and rewrite all traffic coming in on destination port 443 on eth1. On the device I want intercepted, I have imported the ca.cer that mallory generated as a trusted root certificate. I need to analyze some strange behavior in the HTTPS stream between the client and server, so that's why mallory is setup in between for this MITM. I would like to take the decrypted HTTPS traffic and dump it to either a logfile or a socket in a format compatible with tcpdump/wireshark (so I can collect it later and analyze it). Running tcpdump on eth1 is too soon (it's encrypted), and running tcpdump on eth2 is too late (it's been re-encrypted). Is there a way to make mallory "tcpdump" the decrypted traffic (in both directions)?

  Read the article

• Three server processes consume no more than 50% of Dual Core CPU

  - by thor

  I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

  Read the article

• Spreadsheet application that can handle big data OS X

  - by Peter

  I've been working with Excel for quite a while for some statistical analysis that I do regularly. The size of the data that I'm working with has gotten much larger as of late, however. The layout of the databases in question is quite simple, usually just three rows which includes a UNIX timestamp, and EST value, a proprietary numeric value and finally an average of the rows that have a timestamp +/- 1000 that row's timestamp (little AVERAGEIFS() formula). That formula and the EST conversion are the only formulas in the sheet. I'm beginning to work with files with 500,000+ rows. Running the average formula down the entire row takes forever. The end result is the production of print-worthy graphs. I'm looking for either a UNIX CL utility or separate spreadsheet/database application that can handle this amount of data without melting my CPU or making me wait an hour. Is there anything out there? TL;DR: Simple excel sheet with over half a million rows is getting too slow to work with. OS X alternatives?

  Read the article

• Terminal emulation has stopped working. Garbage escape chars

  - by oligofren

  To enable me to do some remote administration of our servers I started using a terminal emulation program called TouchTerm Pro on my iPhone. While not the smoothest experience, it has allowed me to leave my computer behind when going out of town, which makes the slightly painful experience worthwhile. As of late, the app unfortunately no longer works. Pressing up and down keys after logging on via ssh gives me garbage like ^[[A and ^[[B. Combinations with Ctrl - like you can see in the video - no longer works either. Writing full command lines and executing by the enter key works though. Being able to search my bash history was the difference between a usable app and endless frustration, so getting it to work is essential. The app has (of course) met its end of life, not getting updated anymore. I am not quite sure, which side (client or server) that has to be "fixed"/hacked to make the control sequences work again. But is there something I can do to make it work as intended? You can see a video of TouchTerm in operation here.

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Office 2010 OCT Outlook Filepaths

  - by vlannoob

  I'm playing around with customizing Office 2010 installs on my network, normally I just do a full manual install, but as the environment grows and the lazier I get its becoming a pain to do it manually every time. I've read up and downloaded the Office 2010 OCT tool and it looks relatively straight forward - with one exception - the Outlook Profile. I can 'get around it' by just leaving it all as default (or not enabling offline use) but I'd like to customise it slightly so that its all setup no matter who logs onto the PC. The only issue I have, and my question is: In the OCT - Outlook section What do you enter into the Path and Filename for the OST file and the Offline Address book seetings under Enable Offline Use section? I'm sweet with everything else - just that one section, and I think if I bugger that one it will kill the whole Outlook Profile?? It would need to go into each users unique filepath for their profile correct? I have a fair idea of what should be there but I'm struggling with the correct syntax. I know this is a stupid question....but its late in the day and my brain is fried ;) As usual - any and all help/assistance is appreciated ;)

  Read the article

• How do I cancel windows server 2003 repair install?

  - by Kilgore2k

  System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

  Read the article

• Can't find partition tab in disk utility osX ver. 10.6.8

  - by John W

  I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >