Search Results

Search found 1323 results on 53 pages for 'onboard vga'.

Page 29/53 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Erratic display behaviour on 12.04 using an Asus Zenbook

  - by Azarias R

  When I first plugged in my 23 inch monitor through the mini-VGA port, everything worked...both display were detected, and worked. On the second or third plug in, the internal display would turn off, and only the external display would work. When I try to 'detect monitor', I got "could not set the configuration for crtc 63" a few times. Now, when I plug in the external display, I get a screen full of orange color on the external display, and the laptop display turns off. The only way to get things back is to force turn off the laptop and restart. Unplugging/replugging monitor doesn't work, and seems like ubuntu crashes. Can anyone help?

  Read the article

• Dual monitor with different resolutions problem

  - by Mackemint

  I'm on an LG R405 with a PM965 chipset and a NVIDIA GeForce Go 8400M GS gaphics card. I'm trying to use an external monitor (Benq senseye3 G2222HDL) through a VGA out port. All was fine when installing except for the screen layouts were flip-flopped (computer defalut setup so external monitor was to the right instead of left). When I moved the secondary monitor to its real position in the setup, I started getting strange problems. I loose representation of large portions of the screen, on both screens, and have to reboot. If I plug the monitor in after rebooting I get more problems than when booting up with the monitor already plugged in, but in both cases I can barely see what I'm doing. Please advice! Regards /M

  Read the article

• Screen gets garbled on some web sites

  - by user10565

  I have a Gateway notebook with graphics card 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] with open source driver Linux version 2.6.32 -28 - generic. No other operating system on the computer. When I am using firefox to browse the web, everything normally works just fine except that when I attempt to access some particular web pages the screen completely messes up going mostly white with various streaks, etc., although I can access other pages of the same site without problems. When I run the cursor over the garbled screen, bits of the image recompose themselves, at least partially, and I can continue to open the applications window, or turn the computer off, or open the terminal, or take screen shots, etc., although all menus are unreadable. Also, when I zoom in on Google Earth the screen completely messes up. At all other times, there are no apparent problems. Any ideas?

  Read the article

• nVidia FX5200 Can't set resolution upper than 800x600

  - by Sebastian

  When I install nVidia drivers from terminal with this command: sudo apt-get install nvidia-current ... and I reboot, I get the max. resolution 800x600. I added new mode successfully with xrandr, but my display is 480p. My display is connected to my PC with HDMI and in Windows I was have VGA resolution on HDMI but after I installed in Ubuntu the drivers, the resolution is 480p.How to fix that? And can I change the 420p to 720p or 1080i ? Because my display have option "HDMI Full PC mode" which is good because I can see my display fully, but the Full PC mode is not supported for 480p. Ubuntu: 12.04

  Read the article

• problem to change my Xenserver password

  - by Michlaou

  I try to change my root password on my Xenserver 6.0. I follow these steps: enter boot: menu.c32 selecet xe-serial and press tab add "single" before the 2nd triple hyphens and i press enter. I have that: mboot.c32 /boot/xen.gz com1=115200,8n1 console=com1, vga mem=1024G dom0_max_vcpus4 dom0_mem=752M lowmem_emergency_pool=1M crashkernel=64M@32M single --- /boot/vmlinuz-2.6-xen root=LABEL=root-rodraxar ro console=tty0 xencons=hvc console=hvc0 --- /boot/initrd-2.6-xen.img I have commande on the screen and it's stop at: ext3-fs: monted filesystem with ordered data mode. Can you help me?

  Read the article

• (SYSLINUX QUESTION) How to launch command prompt once syslinux boots up

  - by user1294023

  I have created a bootable USB drive using SYSLINUX I am booting my x86 system correctly. Once system boots I want to stop at console (command prompt) where I can type linux commands (cd etc) and run my executable file manually. Does that mean I have to have busy box installed (for basic commands). What makes system stop at command prompt? I do have /dev/console. My serial console is tty1. Any help is appreciated. #syslinux.cfg serial 0 9600 default MyProgram prompt 1 label Linux display message.msg timeout 100 kernel bzImage append console=tty1,9600 vga=773 initrd initrd.img

  Read the article

• How do I install latest NVIDIA drivers from the .run file?

  - by Shahe Tajiryan

  This is what I am trying to do. I downloaded the latest driver for my VGA from http://www.nvidia.com. The installation needs the X11 to be shut down, so I log out of my account, then press CTRL+ALT+F1, then log in with my username and password, then run the command sh NVIDIA-Linux-x86_64-285.05.09.run in every possible way, I have even tried CHMODing the package with 777 permissions, but still I'm getting the sh: can't open NVIDIA-Linux-x86_64-285.05.09.run error. Any help would be greatly appreciated.

  Read the article

• Ubuntu 11.10 boot: xhost: unable to open display

  - by paulus_almighty

  I've had this papercut for a while now, it's time it was fixed. When I boot up Ubuntu, choosing "Ubuntu...generic" from the grub screen, Ubuntu fails to load. It just sits at the driver/module loading screen. What seems to be the most significant line in this output is "xhost: unable to open display" If I choose "Ubuntu...(recovery mode)" from grub then it loads OK. I don't get why this is. Out of interest I tried enabling boot error logging with #/etc/default/bootlogd BOOTLOGD_ENABLE=Yes but I'm not seeing anything in that file. ETA: I've had this problem since fresh install of 11.10. Here's lshw: $ sudo lshw -C display *-display description: VGA compatible controller product: GF104 [GeForce GTX 460] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:03:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f6000000-f7ffffff memory:e0000000-e7ffffff memory:ec000000-efffffff ioport:bf00(size=128) memory:e8000000-e807ffff

  Read the article

• Ubuntu 12.04 ATI 6450

  - by user210717

  Right now my video card isn't responding after the Ubuntu Logo is shown, (I see a black screen and that's it) I have installed ubuntu 12.04 AMD64 and if I remove the video card and use the VGA from the MOBO then I can use it with no problems, other data: 4 GB of ram 1333 500 GB WD AMD APU A6 3500 2,1 GHZ I forgot a couple of details, everything was working great until last night, when the light went off (I don't know if I'm explaining myself I'm from Argentina and english isn't my first language there was a power cut I meant) and then when it got back I used my pc until I went to bed (after upgrading) and this morning, when I woke up I had this problem for breakfast, I've been reading a little and I had a similar problem before and fixed it, but it was a system problem, a missing package or something, I don't remember, but here the only issue is that the video card doesn't give me image after the ubuntu logo.

  Read the article

• Ubuntu will not install on my Dell Inspiron 580

  - by AndrewC

  I'm trying to install ubuntu on my Inspiron 580 (Intel Core i3 4Gb Ram Intel HD Graphics) but am having no success installing from CD or Windows installer all result in a purple rapidly flashing screen with the Ubuntu with 5 dots below it splash which doesn't change. I have tried releases 12.04.1 LTS (CD and windows installer), 11.10 (CD after reading it was certified for the 580) and today 12.10 (CD) all produce the same install failure. My Dell 1704PT monitor is connected to the intel HD board using an HDMI to DVI adaptor though I have tried a VGA cable and still got the same flashing screen. Any help gratefully received as i want to get away from Windows 7 Home Premium.

  Read the article

• Screen rendering problems after upgrading to 12.10

  - by vjrj

  Since upgrading to Ubuntu 12.10 I'm suffering severe rendering issues in unity: Some parts of any application (for instance Firefox, or emacs, etc) are blank, or are not rendered, or are blinking. Some fonts in an application are not correct rendered, maybe only some part (see Eclipse screenshot). There is some shadows in desktop background. It's something that occurs from time to time (it's works great for hours and suddenly start to give this rendering problems). I was trying to find a bug in launchpad but without success. My card (using i915 module): 00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 02) I've tried to reset compiz/unity or gnome but does not help. Any tip? Update: A Firefox screenshot of how my profile in Ask Ubuntu looks like now

  Read the article

• OpenIndiana installation hangs at 2% - Preparing disk for OpenIndiana installation

  - by Chris S

  I've been trying to install OpenIndiana on an HP DL320 G6 for a while now. I've got a 16GB HP SDHC card in the onboard slot and a SATA CD-Rom with oi-dev-151a-text-x86.iso burnt to a disc. Installation seems to progress fine until I get to the actual installation portion. The SD card is picked up as a USB Disk. All the other configuration options are very 'normal' (there really aren't many options to begin with). Automatic NIC configuration. The installer starts "Installing OpenIndiana", does a few steps, then gets to "Preparing disk for OpenIndiana installation" at 2%; and just sits there. I've let it sit for half an hour now ans still no progress. How can I get past this issue? PS I'm not terribly familiar with OpenSolaris, but am with FreeBSD and *nix CLIs in general.

  Read the article

• Dolby Digital Live (DDL) on Asus Rampage II Gene (Creative X-Fi Extreme)

  - by kevyn

  Hi there, I have an Asus Rampage II Gene motherboard which has X-Fi extreme built in. I can get it to work with Windows 7 ok using the Creative drivers, however when I try and install the DDL/DTS add on pack from Creative I get the error message: "There are no supported audio device available. You need to close the application. Click OK to close the application now" I don't understand it because I have the Creative software installed ok and supporting the sound without any problems. In Device manager the audio device comes up as 'High definition audio device' and uses driver: 6.1.7600.16385 from Microsoft. I tried using the Creative drivers which show up as 'soundmax HD audio' however these do not allow any of the Creative products to run properly. Please can anyone offer any help? Or even just confirm that DDL can work with my onboard sound? Windows 7 Ultimate 64 bit 6GB DDR3 XFX GS8800 384mb Asus Rampage II Gene Intel i7 920 (2.66)

  Read the article

• Intel D510MO board - 1000Mbit LAN or not?

  - by T.J. Crowder

  The Intel forum seems to be down (signing in fails with connection refused), but perhaps someone here knows the answer. The Intel D510MO product page says that the LAN is 10/100/1000, but when I look at the NM10 chipset it uses, it says it's just 10/100 (and the detailed PDF spec here backs that up pretty definitively). I don't immediately see anything saying the D510MO has a different LAN controller than the NM10's onboard one, and it would seem odd if it did given the purpose of the board (low power, small footprint; integrated). Does this board support 1000Mbit LAN or not? Anyone have direct knowledge of it? Thanks in advance.

  Read the article

• GeForce 9600GT support for dual monitor setup

  - by Theo

  I have a NVIDIA GeForce 9600 GT (point of view, link) on an Asus M2V-MX motherboard. The card has one DVI, HDMI and S-Video output. The graphics card does not seem to support dual monitors: the driver control panel for the graphics card does not detect a second monitor that is attached via S-Video (which leads me to believe that it doesn't support dual monitors with DVI and the other connections). Would it be possible to use a VGA/DVI splitter to attach two monitors to the single DVI output on the graphics card? Would this allow for a dual monitor setup, or only mirroring? How do I know if the graphic card supports this? With this particular motherboard, would it be possible to use the onboard video for another monitor?

  Read the article

• Switching BIOS SATA RAID/AHCI setting causes BSOD at Windows Start - Why?

  - by thephatp

  I just changed my disk setup from: 1 SATA HDD Primary OS Disk 2x SATA HDD Backup Disks in RAID 1 TO: 1 SATA SSD Primary OS Disk 1 SATA HDD Backup Disk [No RAID] Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo. These are my steps: Settings Integrated Peripherals "SATA RAID/AHCI Mode" = RAID -- Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Next Step: Launch BIOS settings Integrated Peripherals "Onboard SATA/IDE Ctrl Mode" = RAID -- Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues. What am I missing? Why can't I set it to AHCI mode without BSODs?

  Read the article

• Hardware Acceleration on Windows Server 2008

  - by user1184598

  Does Windows Server 2008 have hardware acceleration? I tried to use WPF to make over 20,000 drawings. It only cause around 40% CPU in windows 7. However, I run the same program on Windows Server 2008 with the same hardware configuration except that it has a dedicated graphical display card (GT 9500) while Windows 7 has only an onboard display card, it cause over 80% CPU. So, does Windows Server 2008 have hardware acceleration? Or could I make it? And how do I change the hardware acceleration setting? Thanks.

  Read the article

• No compatible network card

  - by sbintcliffe

  Motherboard: Asus K8N-E Deluxe with onboard NIC (nVidia nForce) Secondary NIC: I've tried using a standard NIC (Device Manager displays this as D-Link DFE-538TX 10/100, but under manufacturer in the General tab of the properties in Windows it states Realtek Semiconductor Corp.) I have downloaded ESXi 4.0.0 build 208167 and cooked to disc. I've booted from it, the .TGZ modules load from the yellow and grey screen, the progress bar reaches to about 60% and like a second later the screen changes and I have the following information on screen; "No compatible network adapter found. Please consult the HCG." I've checked the HCG and found that my motherboard is listed. I also get the same message with the secondary NIC. Any ideas please?

  Read the article

• Enabling Surround sound on a Realtek ALC892 via SPDIF, on Windows 7

  - by Alex

  I have a problem with my ALC892, on an ASRock mainboard (ASRock 890FX Deluxe4). I get only stereo sounds if I use SPDIF connection, in general. My amp shows that is getting surround sound only when I use the Test feature of Windows 7. This test feature allows to know which formats are supported by the audio chip. The tests render correctly both Dolby Digital and DTS. You can find this test under Sounds, Playback Devices, Select Digital Audio, then "Properties". I am using Windows 7 x64, with the latest drivers from the official Realtek website. I also tested other driver versions, both from the Realtek website and from the ASRock one, but had no luck. Thanks for the help. Some specs: CPU: AMD Phenom II X4 965 MOBO: ASRock 890FX Deluxe4 (with onboard Realtek ALC892) Audio amp: Onkyo R-380 (works fine with other sources like PS3 and Xbox 360)

  Read the article

• How to automatically disable secondary monitor in Windows 7

  - by Phenom

  My primary monitor is attached to my onboard video card. My secondary monitor is attached to my PCI-E card. When I first start my computer, only the primary monitor is on, and it is the only monitor that is recognized. While I'm in Windows 7, if I turn on my secondary monitor, Windows 7 automatically detects it, and expands my desktop to stretch across both monitors. But if I turn off the secondary monitor, Windows 7 doesn't automatically disable it. Is there a way I can get it to automatically disable when I turn it off, or is there a utility that makes it easier to disable it instead of having to go to screen resolution?

  Read the article

• Enabling 8021q on a nic

  - by Chris Phillips

  Hi, I'm trying to get a vlan interface on a bonded nic (Centos 5.5) and whilst the interface has been very happily created with vconfig I'm seeing no traffic on it at all. Running tcpdump and tshark on the underlying eth0 I see no sign at all of vlan tags in the traffic, and I'm wondering if there's somethign I'm missing on the server side as the network dept say they are sending me the tagged data. I've got the 8021q module loaded, however under lsmod it shows it's only being used by the cxgb3 module, for an unused onboard iSCSI card, whereas my nics (on an HP DL380 G7) are driven by bnx2 and e1000e modules. Should these modules be listing 8021q as used module? should I have something conrete in /etc/modprobe.conf? Thanks Chris

  Read the article

• Performance difference between MacBook Pro (2.8 GHz) vs Air (1.7 GHz)?

  - by jonathanconway

  I'm comparing these two Apple laptops: MacBook Pro (13", 2011 model): 2.8GHz dual-core Intel Core i7 processor with 4MB shared L3 cache 4GB (two 2GB SO-DIMMs) of 1333MHz DDR3 SDRAM AMD Radeon HD 6770M graphics processor with 1GB of GDDR5 memory on 2.4GHz configuration MacBook Air (13", 2011 model): 1.7GHz dual-core Intel Core i5 with 3MB shared L3 cache 4GB of 1333MHz DDR3 onboard memory Intel HD Graphics 3000 processor with 384MB of DDR3 SDRAM shared with main memory There's definitely a gap between them in terms of CPU speed and graphics, but what practical difference would this make on a day-to-day basis? On the one hand, I love the sleek, thin appearance of the Air. On the other hand, I don't want a machine that's going to be dog-slow when doing tasks such as running Virtual Machines, dual-booting to Windows and running multiple instances of Visual Studio, and maybe some light gaming. Is there going to be a major difference that makes the MacBook Pro a more attractive purchase?

  Read the article

• unable to install new versions of linux on my PC

  - by iamrohitbanga

  I have an MSI-RC410 motherboard with onboard ATI Radeon XPress 200 series Graphics card. I have used OpenSuse-11.0 on my PC for over an year. but when I tried to upgrade to OpenSuse-11.1, I managed to install it only to find that several features were missing. for example /dev/cdrom was missing. Also install DVD of Fedora 11 did not work. I have also tried Ubuntu-9.10 live cd. When I boot from the CD i get the initramfs command prompt. Still able to install old versions of these OSs. What is the reason for this behavior? Does it have to do anything with the new version of the linux kernel not being compatible with my hardware? What should i do to install new versions of Linux?

  Read the article

• Any way to stop VMWare workstation from dropping SSH connections?

  - by oljones

  I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

  Read the article

• Why does my audio keep reverting to stereo?

  - by GraemeF

  I have an ASUS P7P55D LE motherboard with onboard sound and I am running Windows 7 64-bit, and I am using the SPDIF output from my motherboard to my receiver. On my receiver I can see which audio channels are in use (i.e. stereo or 5.1) In the audio interface properties I can test DTS Audio and Dolby Digital outputs and both work fine, but when I try to play a game with 5.1 sound (I've tried Left 4 Dead and Dragon Age Origins) it reverts to stereo. I was getting this behaviour with the default Microsoft drivers so I installed the latest from the ASUS website but there is no difference. I notice that in the Advanced tab the Default Format only allows me to choose from various 2 channel formats so maybe that is something to do with it? How can I get 5.1 output all of the time?

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >