Search Results

Search found 10369 results on 415 pages for 'png 24'.

Page 294/415 | < Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Having problems with high CPU usage and apparent memory leak of Exim

  - by Dancrumb

  I'm having problems with my server and am hoping you can help. The culprit appears to be exim. The CPU usage is consistently high and the memory usage trends up and up and up for no apparent reason (this is not a heavily used server). To demonstrate the issue, I ran the following: root@server [/var/log]# service exim restart; for iter in `seq 0 9`; do date; top -n1 | grep exim; sleep 10; done Shutting down exim: [ OK ] Shutting down spamd: [ OK ] Starting exim: [ OK ] Sun Jun 6 18:12:07 CDT 2010 62592 root 25 0 11400 6572 2356 R 51.5 1.3 0:00.92 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim Sun Jun 6 18:12:18 CDT 2010 62592 root 25 0 28768 23m 2356 R 57.4 4.6 0:06.75 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:28 CDT 2010 62592 root 25 0 36408 30m 2356 R 55.5 6.0 0:12.59 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:39 CDT 2010 62592 root 25 0 41396 35m 2356 R 53.5 7.0 0:18.35 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:49 CDT 2010 62592 root 25 0 45868 40m 2356 R 47.5 7.8 0:24.06 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:00 CDT 2010 62592 root 25 0 50056 44m 2356 R 55.3 8.6 0:29.84 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:10 CDT 2010 62592 root 25 0 53888 47m 2356 R 55.2 9.4 0:35.63 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:21 CDT 2010 62592 root 20 0 56920 50m 2356 R 55.3 9.9 0:41.15 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:31 CDT 2010 62592 root 25 0 60380 54m 2356 R 53.4 10.6 0:46.98 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:42 CDT 2010 62592 root 22 0 63400 57m 2356 R 49.5 11.2 0:52.74 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim After some time, it gets to a rate of picking up an extra MB every 10s. I've checked the exim logs and there are no messages coming in there. exim -bV shows: Exim version 4.69 #1 built 16-Mar-2009 14:44:43 Copyright (c) University of Cambridge 2006 Berkeley DB: Sleepycat Software: Berkeley DB 4.2.52: (February 22, 2005) Support for: crypteq iconv() IPv6 PAM Perl OpenSSL Content_Scanning Old_Demime Experimental_SPF Experimental_SRS Experimental_DomainKeys Lookups: lsearch wildlsearch nwildlsearch iplsearch dbm dbmnz passwd Authenticators: cram_md5 dovecot plaintext spa Routers: accept dnslookup ipliteral manualroute queryprogram redirect Transports: appendfile/maildir autoreply pipe smtp Size of off_t: 8 Configuration file is /etc/exim.conf I'm at something of a loss as to how to proceed. Any recommendations would be well received!

  Read the article

• DNS request timed out. timeout was 2 seconds

  - by sahil007

  i had setup bind dns server on centos. from local lan it will work fine but from remote when i tried to nslookup ..it will give reply like "DNS request timed out...timeout was 2 seconds." what is the problem? this is my bind config---- // Red Hat BIND Configuration Tool options { directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; query-source address * port 53; }; controls { inet 127.0.0.1 allow {localhost; } keys {rndckey; }; }; acl internals { 127.0.0.0/8; 192.168.0.0/24; 10.0.0.0/8; }; view "internal" { match-clients { internals; }; recursion yes; zone "mydomain.com" { type master; file "mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; zone "." IN { type hint; file "named.root"; }; zone "localdomain." IN { type master; file "localdomain.zone"; allow-update { none; }; }; zone "localhost." IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa." IN { type master; file "named.local"; allow-update { none; }; }; zone "0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa." I N { type master; file "named.ip6.local"; allow-update { none; }; }; zone "255.in-addr.arpa." IN { type master; file "named.broadcast"; allow-update { none; }; }; zone "0.in-addr.arpa." IN { type master; file "named.zero"; allow-update { none; }; }; }; view "external" { match-clients { any; }; recursion no; zone "mydomain.com" { type master; file "mydomain.com.zone"; // file "/var/named/chroot/var/named/mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; }; include "/etc/rndc.key";

  Read the article

• Apache cyclic redirection problem

  - by slicedlime

  I have an extremely weird problem with one of my sites. I run a number of blogs off a single apache2 server with a shared wordpress install. Each site has a www.domain.com main domain, but a ServerAlias of domain.com. This works fine for all the blogs except one, which instead of redirecting to www.domain.com redirects to domain.com, causing a cyclic redirection. The configuration for each host looks like this: <VirtualHost *:80> ServerName www.domain.com ServerAlias domain.com DocumentRoot "/home/www/www.domain.com" <Directory "/home/www/www.domain.com"> Options MultiViews Indexes Includes FollowSymLinks ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> As this didn't work, I tried a mod_rewrite rule for it, which still didn't redirect correctly. The weird thing here is that if i rewrite it to redirect to any other domain it will redirect correctly, even to another subdomain. So a rewrite rule for domain.com that redirects to foo.domain.com works, but not to www.domain.com. In the same way, trying to redirec to www.domain.com/foo/ ends me up with a redirection to domain.com/foo/. Even weirder, I tried setting up domain.com as a completely separate virtual host, and ran this php test script as index.php on it: <?php header('Location: http://www.domain.com/' . $_SERVER["request_uri"]); ?> Hitting domain.com still redirects to domain.com! Checking out the headers sent to the server verifies that I get exactly the redirect URL I wanted, except with the "www." stripped. The same script works like a charm if I replace www. with foo or redirect to any other domain. This has now foiled me for a long time. I've diffed the vhosts configs for a working domain and the faulty one, and the only difference is the domain name itself. I've diffed the .htaccess files for both sites, and the only difference is a path related to the sharing of wordpress installation for the blogs: php_value include_path ".:/home/www/www.domain.com/local/:/home/www/www.domain.com/" I searched through everything in /etc (including apache conf) for the domain name of the faulty host and found nothing weird, searched through everything in /etc for one of the working ones to make sure it didn't differ, I even went so far to check on the DNS setup of two domains to make sure there wasn't anything strange going on. Here's the response for the faulty one: user@localhost dir $ wget -S domain.com --2010-03-20 21:47:24-- http://domain.com/ Resolving domain.com... x.x.x.x Connecting to domain.com|x.x.x.x|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 301 Moved Permanently Via: 1.1 ISA Connection: Keep-Alive Proxy-Connection: Keep-Alive Content-Length: 0 Date: Sat, 20 Mar 2010 20:47:24 GMT Location: http://domain.com/ Content-Type: text/html; charset=UTF-8 Server: Apache X-Powered-By: PHP/5.2.10-pl0-gentoo X-Pingback: http://domain.com/xmlrpc.php Keep-Alive: timeout=15, max=100 Location: http://domain.com/ [following] And a working one: user@localhost dir $ wget -S domain.com --2010-03-20 21:51:33-- http://domain.com/ Resolving domain.com... x.x.x.x Connecting to domain.com|x.x.x.x|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 301 Moved Permanently Via: 1.1 ISA Connection: Keep-Alive Proxy-Connection: Keep-Alive Content-Length: 0 Date: Sat, 20 Mar 2010 20:51:33 GMT Location: http://www.domain.com/ Content-Type: text/html; charset=UTF-8 Server: Apache X-Powered-By: PHP/5.2.10-pl0-gentoo X-Pingback: http://www.domain.com/xmlrpc.php Keep-Alive: timeout=15, max=100 Location: http://www.domain.com/ [following] I'm stumped. I've had this problem for a long time, and I feel like I've tried everything. I can't see why the different domains would act differently under the same installation with the same settings. Help :(

  Read the article

• How can I forward ALL traffic over a site-to-site VPN on Cisco ASA?

  - by Scott Clements

  Hi There, I currently have two Cisco ASA 5100 routers. They are at different physical sites and are configured with a site-to-site VPN which is active and working. I can communicate with the subnets on either site from the other and both are connected to the internet, however I need to ensure that all the traffic at my remote site goes through this VPN to my site here. I know that the web traffic is doing so as a "tracert" confirms this, but I need to ensure that all other network traffic is being directed over this VPN to my network here. Here is my config for the ASA router at my remote site: hostname ciscoasa domain-name xxxxx enable password 78rl4MkMED8xiJ3g encrypted names ! interface Ethernet0/0 nameif NIACEDC security-level 100 ip address x.x.x.x 255.255.255.0 ! interface Ethernet0/1 description External Janet Connection nameif JANET security-level 0 ip address x.x.x.x 255.255.255.248 ! interface Ethernet0/2 shutdown no nameif security-level 100 no ip address ! interface Ethernet0/3 shutdown no nameif security-level 100 ip address dhcp setroute ! interface Management0/0 nameif management security-level 100 ip address 192.168.100.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup NIACEDC dns server-group DefaultDNS name-server 154.32.105.18 name-server 154.32.107.18 domain-name XXXX same-security-traffic permit inter-interface same-security-traffic permit intra-interface access-list ren_access_in extended permit ip any any access-list ren_access_in extended permit tcp any any access-list ren_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_nat0_outbound extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list JANET_20_cryptomap extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_access_in extended permit ip any any access-list NIACEDC_access_in extended permit tcp any any access-list JANET_access_out extended permit ip any any access-list NIACEDC_access_out extended permit ip any any pager lines 24 logging enable logging asdm informational mtu NIACEDC 1500 mtu JANET 1500 mtu management 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-522.bin no asdm history enable arp timeout 14400 nat-control global (NIACEDC) 1 interface global (JANET) 1 interface nat (NIACEDC) 0 access-list NIACEDC_nat0_outbound nat (NIACEDC) 1 192.168.12.0 255.255.255.0 access-group NIACEDC_access_in in interface NIACEDC access-group NIACEDC_access_out out interface NIACEDC access-group JANET_access_out out interface JANET route JANET 0.0.0.0 0.0.0.0 194.82.121.82 1 route JANET 0.0.0.0 0.0.0.0 192.168.3.248 tunneled timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute http server enable http 192.168.12.0 255.255.255.0 NIACEDC http 192.168.100.0 255.255.255.0 management http 192.168.9.0 255.255.255.0 NIACEDC no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto map JANET_map 20 match address JANET_20_cryptomap crypto map JANET_map 20 set pfs crypto map JANET_map 20 set peer X.X.X.X crypto map JANET_map 20 set transform-set ESP-AES-256-SHA crypto map JANET_map interface JANET crypto isakmp enable JANET crypto isakmp policy 10 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication pre-share encryption aes-256 hash sha group 5 lifetime 86400 tunnel-group X.X.X.X type ipsec-l2l tunnel-group X.X.X.X ipsec-attributes pre-shared-key * telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd address 192.168.100.2-192.168.100.254 management dhcpd enable management ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect http ! service-policy global_policy global prompt hostname context no asdm history enable Thanks in advance, Scott

  Read the article

• WHM Checking server status so frequently?

  - by Webnet

  Why do I have so many whm-server-status elements on this Apache status screen for WHM. 0-1 28256 0/4/808 _ 0.20 5 26 0.0 0.19 6.62 72.95.166.85 diablo-source.gamer-source.com GET /lib/ajax/keep-alive.php?_dc=1276829050557 HTTP/1.1 1-1 28259 0/5/934 _ 0.00 4 188 0.0 0.06 6.67 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0 2-1 - 0/0/940 . 0.18 55 0 0.0 0.00 6.61 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 3-1 - 0/0/914 . 0.49 28 0 0.0 0.00 8.46 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 4-1 - 0/0/837 . 0.00 62 0 0.0 0.00 7.49 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 5-1 27580 0/15/849 _ 6.36 7 188 0.0 0.69 6.89 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0 6-1 - 0/0/829 . 0.00 58 0 0.0 0.00 4.20 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 7-1 - 0/0/878 . 0.03 47 0 0.0 0.00 4.62 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 8-1 26737 0/19/759 W 7.55 93 0 0.0 0.93 8.24 76.76.103.50 gamer-source.com GET /development-blog/?p=101&cpage=108 HTTP/1.0 9-1 - 0/0/847 . 0.36 61 0 0.0 0.00 7.90 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 10-1 28233 0/8/705 _ 0.17 6 201 0.0 0.06 6.18 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0 11-1 - 0/0/754 . 0.00 48 0 0.0 0.00 6.50 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 12-1 28235 0/6/670 W 0.11 25 0 0.0 0.04 3.15 76.76.103.50 gamer-source.com GET /development-blog/?p=104&cpage=1 HTTP/1.0 13-1 - 0/0/611 . 0.00 60 0 0.0 0.00 4.76 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 14-1 - 0/0/713 . 0.00 59 0 0.0 0.00 5.70 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 15-1 - 0/0/696 . 0.00 57 0 0.0 0.00 4.85 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 16-1 - 0/0/695 . 0.50 73 0 0.0 0.00 4.43 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 17-1 - 0/0/547 . 0.17 56 0 0.0 0.00 4.89 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 18-1 - 0/0/472 . 0.00 80 0 0.0 0.00 2.05 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 19-1 27588 0/7/423 _ 6.59 1 184 0.0 0.69 2.79 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0 20-1 27589 0/6/420 _ 6.54 3 184 0.0 0.71 3.62 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0 21-1 28242 0/10/374 _ 0.44 6 819 0.0 0.05 1.81 67.195.114.23 gamer-source.com GET /development-blog/?p=120 HTTP/1.0 22-1 - 0/0/359 . 0.00 79 0 0.0 0.00 3.45 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 23-1 - 0/0/326 . 0.16 163 0 0.0 0.00 2.64 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 24-1 - 0/0/430 . 0.40 74 0 0.0 0.00 3.30 127.0.0.1 server.gospire.com OPTIONS * HTTP/1.0 25-1 27624 0/23/276 W 0.78 0 0 0.0 0.16 1.08 127.0.0.1 server.gospire.com GET /whm-server-status/ HTTP/1.0

  Read the article

• Diagnosing Solaris 8 server memory and swap space usage

  - by datSilencer

  Hello everyone. Essentially, my question is related to memory allocation for Solaris virtual machines. I am running a couple of old Sun ONE 6 Java web servers on two Solaris 8 virtual machines. I see that there's a reasonable amount of swap space being used, but I'm not exactly sure if this could indicate a need to add more RAM to these machines. At service peak hours (mornings usually), the response time of the web application these servers host jumps up to at most 11 seconds (somewhat detrimental for a relatively simple web page loading action). Average response time at non peak times is about 5 seconds. What would you be able to infer about the RAM usage for these machines from the ouput below? Is this information reasonably sufficient? Or would I need to run some other commands to rule out server memory starvation? Finally, since there is a Java application at the core of the setup, I've also thought about: 1) Trace the heap's Object allocation to detect potential memory leaks. 2) Do some performance profiling to see if this instead related to networking delays. I mention this since the application talks with a single Oracle Database, but I would doubt this to be the case since they're pretty close from a network segmentation perspective. I appreciate any kind of insight and feedback you could provide. Thanks for your time and help. Server 1: 40 processes: 38 sleeping, 1 zombie, 1 on cpu CPU states: 99.1% idle, 0.4% user, 0.4% kernel, 0.0% iowait, 0.0% swap Memory: 2048M real, 295M free, 865M swap in use, 3788M swap free PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND 12676 webservd 112 29 10 616M 242M sleep 103:37 0.48% webservd 18317 root 1 59 0 23M 19M sleep 67:24 0.08% perl 9479 support 1 59 0 6696K 2448K cpu/1 0:11 0.05% top 8012 root 10 59 0 34M 704K sleep 80:54 0.04% java 1881 root 33 29 10 110M 13M sleep 33:03 0.02% webservd 7808 root 1 59 0 83M 67M sleep 7:59 0.00% perl 1461 root 20 59 0 5328K 1392K sleep 6:49 0.00% syslogd 1691 root 2 59 0 27M 680K sleep 4:22 0.00% webservd 24386 root 1 59 0 15M 11M sleep 2:50 0.00% perl 23259 root 1 59 0 11M 4240K sleep 2:42 0.00% perl 24718 root 1 59 0 11M 5464K sleep 2:29 0.00% perl 22810 root 1 59 0 19M 11M sleep 2:21 0.00% perl 24451 root 1 53 2 11M 3800K sleep 2:18 0.00% perl 18501 root 1 56 1 11M 3960K sleep 2:18 0.00% perl 14450 root 1 56 1 15M 6920K sleep 1:49 0.00% perl Server 2 42 processes: 40 sleeping, 1 zombie, 1 on cpu CPU states: 98.8% idle, 0.4% user, 0.8% kernel, 0.0% iowait, 0.0% swap Memory: 1024M real, 31M free, 554M swap in use, 3696M swap free PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND 5607 webservd 74 29 10 284M 173M sleep 20:14 0.21% webservd 15919 support 1 59 0 4056K 2520K cpu/1 0:08 0.09% top 13138 root 10 59 0 34M 1952K sleep 210:51 0.08% java 13753 root 1 59 0 22M 12M sleep 170:15 0.07% perl 22979 root 33 29 10 112M 7864K sleep 85:07 0.04% webservd 22930 root 1 59 0 3424K 1552K sleep 17:47 0.01% xntpd 22978 root 2 59 0 27M 2296K sleep 10:49 0.00% webservd 13571 root 1 59 0 9400K 5112K sleep 5:52 0.00% perl 5606 root 2 29 10 29M 9056K sleep 0:36 0.00% webservd 15910 support 1 59 0 9128K 2616K sleep 0:00 0.00% sshd 13106 root 1 59 0 82M 3520K sleep 7:47 0.00% perl 13547 root 1 59 0 12M 5528K sleep 6:38 0.00% perl 13518 root 1 59 0 9336K 3792K sleep 6:24 0.00% perl 13399 root 1 56 1 8072K 3616K sleep 5:18 0.00% perl 13557 root 1 53 2 8248K 3624K sleep 5:12 0.00% perl

  Read the article

• routing specific IP to ppp0 tunnel

  - by gompertz

  Hi All, I feel I've struggled with this long enough and need some help. I have a pptp tunnel and am trying to route destination traffic from 208.85.40.20 to the pptp tunnel (ppp0). (Keen observers may recognize the ip as being that of pandora.com). I am doing all this configuration on a router... and I know it's not working successfully as traceroute yields nothing but astericks. I've pasted relevant outputs below: (with some "security" editing to the addresses) root@OpenWrt:~# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28185 errors:0 dropped:0 overruns:0 frame:0 TX packets:24936 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4894242 (4.6 MiB) TX bytes:5941902 (5.6 MiB) eth0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:51829 errors:0 dropped:0 overruns:0 frame:0 TX packets:56824 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11490288 (10.9 MiB) TX bytes:11857913 (11.3 MiB) Interrupt:4 eth2 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:15426 TX packets:9529 errors:21 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:423 (423.0 B) TX bytes:596036 (582.0 KiB) Interrupt:2 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2300 (2.2 KiB) TX bytes:2300 (2.2 KiB) ppp0 Link encap:Point-Point Protocol inet addr:68.68.39.250 P-t-P:172.16.20.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:165 errors:2 dropped:0 overruns:0 frame:0 TX packets:68 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:7006 (6.8 KiB) TX bytes:3462 (3.3 KiB) vlan0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:28182 errors:0 dropped:0 overruns:0 frame:0 TX packets:33813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5006544 (4.7 MiB) TX bytes:6609774 (6.3 MiB) vlan1 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:173.183.111.3 Bcast:173.183.111.255 Mask:255.255.224.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23653 errors:0 dropped:0 overruns:0 frame:0 TX packets:23012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5522012 (5.2 MiB) TX bytes:4982944 (4.7 MiB) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# cat /etc/ppp/ip-up iptables -A FORWARD -t filter -i br0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.1.1/24 -d 0/0 -j MASQUERADE iptables -A forwarding_rule -o ppp0 -j ACCEPT iptables -A forwarding_rule -i ppp0 -j ACCEPT iptables -t nat -A postrouting_rule -o ppp0 -j MASQUERADE root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.20.1 * 255.255.255.255 UH 0 0 0 ppp0 208.85.40.20 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 173.183.192.0 * 255.255.224.0 U 0 0 0 vlan1 default d173-183-192-1. 0.0.0.0 UG 0 0 0 vlan1 default 192.168.1.1 0.0.0.0 UG 0 0 0 br0 Any advice is greatly appreciated, I'm not too great with network but am pretty astute at learning ;-)

  Read the article

• Low load average with plenty of cpu-intersive processes

  - by sds

  I see loadavg at about 1 with at least 3 processes running at full tile. How can that be? top - 11:48:32 up 147 days, 5:38, 8 users, load average: 1.08, 1.11, 1.05 Tasks: 416 total, 4 running, 410 sleeping, 2 stopped, 0 zombie Cpu0 : 43.3%us, 13.7%sy, 0.0%ni, 43.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 48.8%us, 12.4%sy, 0.0%ni, 38.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.7%us, 0.7%sy, 0.0%ni, 98.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu3 : 99.3%us, 0.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 0.0%us, 0.3%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 5.7%us, 0.7%sy, 0.0%ni, 93.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 2.3%us, 0.3%sy, 0.0%ni, 97.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 0.3%us, 0.3%sy, 0.0%ni, 99.0%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu8 : 38.4%us, 17.4%sy, 0.0%ni, 44.2%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu9 : 43.4%us, 13.5%sy, 0.0%ni, 43.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu10 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu11 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu12 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu13 : 0.3%us, 0.3%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu14 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu15 : 1.0%us, 0.7%sy, 0.0%ni, 98.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 132145404k total, 88125080k used, 44020324k free, 516476k buffers Swap: 8388600k total, 620232k used, 7768368k free, 55729064k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 25424 jonathan 20 0 4404m 4.1g 3268 R 99.7 3.3 212:58.17 python2.7 20939 sam 20 0 908m 733m 3376 R 81.2 0.6 603:08.07 python2.7 20987 sam 20 0 908m 732m 3376 R 79.8 0.6 598:49.18 python2.7 25428 jonathan 20 0 774m 164m 15m S 14.2 0.1 24:22.60 java 20996 sam 20 0 98.4m 7780 1880 S 4.3 0.0 17:48.15 vw 20941 sam 20 0 161m 70m 1880 S 3.0 0.1 18:10.03 vw 20940 sam 20 0 98.4m 8068 1880 S 2.6 0.0 18:06.28 vw 20942 sam 20 0 98.4m 8080 1880 S 2.6 0.0 17:39.45 vw 20944 sam 20 0 161m 71m 1880 S 2.6 0.1 17:29.29 vw 20947 sam 20 0 161m 71m 1880 S 2.6 0.1 17:25.58 vw 20959 sam 20 0 161m 70m 1880 S 2.6 0.1 17:28.00 vw 20962 sam 20 0 161m 70m 1880 S 2.6 0.1 17:26.96 vw 20963 sam 20 0 98.4m 8076 1880 S 2.6 0.0 18:07.19 vw 20965 sam 20 0 161m 71m 1880 S 2.6 0.1 18:08.13 vw 20995 sam 20 0 161m 71m 1880 S 2.6 0.1 17:38.67 vw 6399 root 20 0 558m 19m 5028 S 2.3 0.0 4329:56 BESClient 20945 sam 20 0 98.4m 8068 1880 S 2.3 0.0 17:35.38 vw 20948 sam 20 0 98.4m 8068 1880 S 2.3 0.0 17:26.01 vw 20950 sam 20 0 161m 70m 1880 S 2.3 0.1 17:25.79 vw 20952 sam 20 0 98.4m 8076 1880 S 2.3 0.0 17:32.94 vw 20955 sam 20 0 161m 70m 1880 S 2.3 0.1 17:26.61 vw 20956 sam 20 0 98.4m 8072 1880 S 2.3 0.0 17:34.76 vw 20960 sam 20 0 98.4m 8072 1880 S 2.3 0.0 17:34.04 vw Adding up CPU loads gives about 300%. The top process list also adds up to about 300%. Why is load average about 1?

  Read the article

• Using Juniper EX3300 as a router

  - by Richard Whitman

  So I have a Juniper EX3300 Switch. One of its uplink ports (ge-0/1/0) is connected to my ISP's router. ISP router's port address is xx.xx.xx.109. My switch's IP address is xx.xx.xx.110. From the switch, I can ping to xx.xx.xx.109 and any other IP in the world. I mean its connected to the Internet. I connected the port eth0 of a computer (running Ubuntu) to the port ge-0/0/0 of the switch (which in the same VLAN as ge-0/1/0). I configured the port eth0 as follows: iface eth0 inet static address yy.yy.yy.208 netmask 255.255.255.240 gateway xx.xx.xx.110 yy.yy.yy.208 is assigned to me by the ISP. So, now I can ping to the switch (xx.xx.xx.110) from this computer. But I can not ping to either xx.xx.xx.109 (ISP router) or any other IP. I want this computer to be connected to the Internet. What am I doing wrong? Here are some of the configurations on my switch: interfaces { ge-0/0/0 { unit 0 { family ethernet-switching; } } . . . ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family ethernet-switching { port-mode access; } } } . . . vlan { unit 0 { family inet { address 10.0.1.1/24; } } unit 1 { family inet { address xx.xx.xx.110/30; } } } } . . . routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.109; retain; } } } vlans { Cogent { vlan-id 3; interface { ge-0/1/0.0; ge-0/0/0.0; ge-0/0/1.0; ge-0/0/2.0; ge-0/0/3.0; } l3-interface vlan.1; } TFLan { vlan-id 2; interface { ge-0/0/5.0; ge-0/0/6.0; ge-0/0/7.0; ge-0/0/8.0; ge-0/0/9.0; ge-0/0/10.0; ge-0/0/11.0; ge-0/0/12.0; ge-0/0/13.0; ge-0/0/14.0; ge-0/0/15.0; ge-0/0/16.0; ge-0/0/17.0; ge-0/0/18.0; ge-0/0/19.0; ge-0/0/20.0; ge-0/0/21.0; ge-0/0/22.0; ge-0/0/23.0; ge-0/0/4.0; } l3-interface vlan.0; } }

  Read the article

• Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• Cannot read status the monit daemon, even with allowed group

  - by jefflunt

  I cannot seem to get monit status or other CLI commands to work. I've built monit v5.8 to run on a Raspberry Pi. I'm able to add services to be monitored, and the web interface can be accessed just fine, as I've set it up for public read-only access (it's a test server, not my final production setup, so not a big deal right now). Problem is, when I run monit status while logged in as root I get: # monit status monit: cannot read status from the monit daemon I also have monit started on boot via this /etc/inittab file entry: mo:2345:respawn:/usr/local/bin/monit -Ic /etc/monitrc I've verified that monit is running, and I'm getting email alerts anytime I either kill the monit process manually, or reboot my raspberry pi. So, next I check my monitrc file permissions to see which group is allowed access. # ls -al /etc/monitrc -rw------- 1 root root 2359 Aug 24 14:48 /etc/monitrc Here's my relevant allow section of the control file. set httpd port 80 allow [omitted] readonly allow @root allow localhost allow 0.0.0.0/0.0.0.0 Also tried setting permissions on this file to 640 to allow group read permissions, but no matter what I try I either get the same error as noted above, or when the permissions are set to 640 I get: # monit status monit: The control file '/etc/monitrc' must have permissions no more than -rwx------ (0700); right now permissions are -rw-r----- (0640). What am I missing here? I know that the httpd must be enabled, as that's the interface that the CLI uses to get information (or so I've read), so I've done that. And in terms of monit doing its monitoring job and sending email alerts, that's all working as well. Here's my entire monitrc file - again, this is version v5.8, and it was build with both PAM and SSL support. The process runs under the root user: # Global settings set daemon 300 with start delay 5 set logfile /var/log/monit.log set pidfile /var/run/monit.pid set idfile /var/run/.monit.id set statefile /var/run/.monit.state # Mail alerts ## Set the list of mail servers for alert delivery. Multiple servers may be ## specified using a comma separator. If the first mail server fails, Monit # will use the second mail server in the list and so on. By default Monit uses # port 25 - it is possible to override this with the PORT option. # set mailserver smtp.gmail.com port 587 username [omitted] password [omitted] using tlsv1 ## Send status and events to M/Monit (for more informations about M/Monit ## see http://mmonit.com/). By default Monit registers credentials with ## M/Monit so M/Monit can smoothly communicate back to Monit and you don't ## have to register Monit credentials manually in M/Monit. It is possible to ## disable credential registration using the commented out option below. ## Though, if safety is a concern we recommend instead using https when ## communicating with M/Monit and send credentials encrypted. # # set mmonit http://monit:[email protected]:8080/collector # # and register without credentials # Don't register credentials # # ## Monit by default uses the following format for alerts if the the mail-format ## statement is missing:: set mail-format { from: [email protected] subject: $SERVICE $DESCRIPTION message: $EVENT Service: $SERVICE Date: $DATE Action: $ACTION Host: $HOST Description: $DESCRIPTION Monit instance provided by chicagomeshnet.com } # Web status page set httpd port 80 allow [omitted] readonly allow @root allow localhost allow 0.0.0.0/0.0.0.0 ## You can set alert recipients whom will receive alerts if/when a ## service defined in this file has errors. Alerts may be restricted on ## events by using a filter as in the second example below.

  Read the article

• Kernel panic when bringing up DRBD resource

  - by sc.

  I'm trying to set up two machines synchonizing with DRBD. The storage is setup as follows: PV - LVM - DRBD - CLVM - GFS2. DRBD is set up in dual primary mode. The first server is set up and running fine in primary mode. The drives on the first server have data on them. I've set up the second server and I'm trying to bring up the DRBD resources. I created all the base LVM's to match the first server. After initializing the resources with `` drbdadm create-md storage I'm bringing up the resources by issuing drbdadm up storage After issuing that command, I get a kernel panic and the server reboots in 30 seconds. Here's a screen capture. My configuration is as follows: OS: CentOS 6 uname -a Linux host.structuralcomponents.net 2.6.32-279.5.2.el6.x86_64 #1 SMP Fri Aug 24 01:07:11 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux rpm -qa | grep drbd kmod-drbd84-8.4.1-2.el6.elrepo.x86_64 drbd84-utils-8.4.1-2.el6.elrepo.x86_64 cat /etc/drbd.d/global_common.conf global { usage-count yes; # minor-count dialog-refresh disable-ip-verification } common { handlers { pri-on-incon-degr "/usr/lib/drbd/notify-pri-on-incon-degr.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; pri-lost-after-sb "/usr/lib/drbd/notify-pri-lost-after-sb.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; local-io-error "/usr/lib/drbd/notify-io-error.sh; /usr/lib/drbd/notify-emergency-shutdown.sh; echo o /proc/sysrq-trigger ; halt -f"; # fence-peer "/usr/lib/drbd/crm-fence-peer.sh"; # split-brain "/usr/lib/drbd/notify-split-brain.sh root"; # out-of-sync "/usr/lib/drbd/notify-out-of-sync.sh root"; # before-resync-target "/usr/lib/drbd/snapshot-resync-target-lvm.sh -p 15 -- -c 16k"; # after-resync-target /usr/lib/drbd/unsnapshot-resync-target-lvm.sh; } startup { # wfc-timeout degr-wfc-timeout outdated-wfc-timeout wait-after-sb become-primary-on both; wfc-timeout 30; degr-wfc-timeout 10; outdated-wfc-timeout 10; } options { # cpu-mask on-no-data-accessible } disk { # size max-bio-bvecs on-io-error fencing disk-barrier disk-flushes # disk-drain md-flushes resync-rate resync-after al-extents # c-plan-ahead c-delay-target c-fill-target c-max-rate # c-min-rate disk-timeout } net { # protocol timeout max-epoch-size max-buffers unplug-watermark # connect-int ping-int sndbuf-size rcvbuf-size ko-count # allow-two-primaries cram-hmac-alg shared-secret after-sb-0pri # after-sb-1pri after-sb-2pri always-asbp rr-conflict # ping-timeout data-integrity-alg tcp-cork on-congestion # congestion-fill congestion-extents csums-alg verify-alg # use-rle protocol C; allow-two-primaries yes; after-sb-0pri discard-zero-changes; after-sb-1pri discard-secondary; after-sb-2pri disconnect; } } cat /etc/drbd.d/storage.res resource storage { device /dev/drbd0; meta-disk internal; on host.structuralcomponents.net { address 10.10.1.120:7788; disk /dev/vg_storage/lv_storage; } on host2.structuralcomponents.net { address 10.10.1.121:7788; disk /dev/vg_storage/lv_storage; } /var/log/messages is not logging anything about the crash. I've been trying to find a cause of this but I've come up with nothing. Can anyone help me out? Thanks.

  Read the article

• Postfix on Snow Leopard unable to send MIME emails, including header contents in message body

  - by devvy

  I configured postfix on snow leopard by adding the following line to /etc/hostconfig: MAILSERVER=-YES- I then configured postfix to relay through my ISP's SMTP server. I added the following two lines in their respective places within /etc/postfix/main.cf: myhostname = 1and1.com relayhost = shawmail.vc.shawcable.net I then have a simple PHP mail function wrapper as follows: send_email("[email protected]", "[email protected]", "Test Email", "<p>This is a simple HTML email</p>"); echo "Done"; function send_email($from,$to,$subject,$message){ $header="From: <".$from."> "; $header.= 'MIME-Version: 1.0' . " "; $header.= 'Content-type: text/html; charset=iso-8859-1' . " "; $send_mail=mail($to,$subject,$message,$header); if(!$send_mail){ echo "ERROR"; } } With this, I am receiving an e-mail that appears to be improperly formatted. The message header is showing up in the body of the e-mail. The raw message content is as follows: Return-Path: <[email protected]> Delivery-Date: Tue, 27 Apr 2010 18:12:48 -0400 Received: from idcmail-mo2no.shaw.ca (idcmail-mo2no.shaw.ca [64.59.134.9]) by mx.perfora.net (node=mxus2) with ESMTP (Nemesis) id 0M4XlU-1NCtC81GVY-00z5UN for [email protected]; Tue, 27 Apr 2010 18:12:48 -0400 Message-Id: <[email protected]> Received: from pd6ml3no-ssvc.prod.shaw.ca ([10.0.153.149]) by pd6mo1no-svcs.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:47 -0600 X-Cloudmark-SP-Filtered: true X-Cloudmark-SP-Result: v=1.0 c=1 a=VphdPIyG4kEA:10 a=hATtCjKilyj9ZF5m5A62ag==:17 a=mC_jT1gcAAAA:8 a=QLyc3QejAAAA:8 a=DGW4GvdtALggLTu6w9AA:9 a=KbDtEDGyCi7QHcNhDYYwsF92SU8A:4 a=uch7kV7NfGgA:10 a=5ZEL1eDBWGAA:10 Received: from unknown (HELO 1and1.com) ([24.84.196.104]) by pd6ml3no-dmz.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:48 -0600 Received: by 1and1.com (Postfix, from userid 70) id BB08D14ECFC; Tue, 27 Apr 2010 15:12:47 -0700 (PDT) To: [email protected] Subject: Test Email X-PHP-Originating-Script: 501:test.php Date: Tue, 27 Apr 2010 18:12:48 -0400 X-UI-Junk: AutoMaybeJunk +30 (SPA); V01:LYI2BGRt:7TwGx5jxe8cylj5nOTae9JQXYqoWvG2w4ZSfwYCXmHCH/5vVNCE fRD7wNNM86txwLDTO522ZNxyNHhvJUK9d2buMQuAUCMoea2jJHaDdtRgkGxNSkO2 v6svm0LsZikLMqRErHtBCYEWIgxp2bl0W3oA3nIbtfp3li0kta27g/ZjoXcgz5Sw B8lEqWBqKWMSta1mCM+XD/RbWVsjr+LqTKg== Envelope-To: [email protected] From: <[email protected]> MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 Message-Id: <[email protected]> Date: Tue, 27 Apr 2010 15:12:47 -0700 (PDT) <p>This is a simple HTML email</p> And here are the contents of my /var/log/mail.log file after sending the email: Apr 27 15:29:01 User-iMac postfix/qmgr[705]: 74B1514EDDF: removed Apr 27 15:29:30 User-iMac postfix/pickup[704]: 25FBC14EDF0: uid=70 from=<_www> Apr 27 15:29:30 User-iMac postfix/master[758]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable Apr 27 15:29:30 User-iMac postfix/cleanup[745]: 25FBC14EDF0: message-id=<[email protected]> Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: from=<[email protected]>, size=423, nrcpt=1 (queue active) Apr 27 15:29:30 User-iMac postfix/smtp[747]: 25FBC14EDF0: to=<[email protected]>, relay=shawmail.vc.shawcable.net[64.59.128.135]:25, delay=0.21, delays=0.01/0/0.1/0.1, dsn=2.0.0, status=sent (250 ok: Message 25784419 accepted) Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: removed Two other people in the office have followed the exact same process and are running the exact same script, version of snow leopard, php, etc. and everything is working fine for them. I've even copied their config files to my machine, restarted postfix, restarted apache, all to no avail. Does anyone know what steps I could take to resolve the issue? This is boggling my mind... Thanks

  Read the article

• wireless internet in linux is very very slow... but in windows.... everythnings fine

  - by Cody Acer

  yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

  Read the article

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• Postfix certificate verification failed for smtp.gmail.com

  - by Andi Unpam

  I have problem, my email server using postfix with gmail smtp, i use account google apps, but always ask for SASL authentication failed, I sent an email using php script, after I see the error logs in the wrong password, after I open the URL from the browser and no verification postfixnya captcha and could return, but after 2-3 days later happen like that again. This my config postfix #myorigin = /etc/mailname smtpd_banner = Hostingbitnet Mail Server biff = no append_dot_mydomain = no readme_directory = no myhostname = webmaster.hostingbitnet.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost, webmaster.hostingbitnet.com, localhost.localdomain, 103.9.126.163 relayhost = [smtp.googlemail.com]:587 relay_transport = relay relay_destination_concurrency_limit = 1 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 103.9.126.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all default_transport = smtp relayhost = [smtp.gmail.com]:587 smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/google-apps smtp_sasl_security_options = noanonymous smtp_use_tls = yes smtp_sender_dependent_authentication = yes tls_random_source = dev:/dev/urandom default_destination_concurrency_limit = 1 smtp_tls_CAfile = /etc/postfix/tls/root.crt smtp_tls_cert_file = /etc/postfix/tls/cert.pem smtp_tls_key_file = /etc/postfix/tls/privatekey.pem smtp_tls_session_cache_database = btree:$data_directory/smtp_tls_session_cache smtp_tls_security_level = may smtp_tls_loglevel = 1 smtpd_tls_CAfile = /etc/postfix/tls/root.crt smtpd_tls_cert_file = /etc/postfix/tls/cert.pem smtpd_tls_key_file = /etc/postfix/tls/privatekey.pem smtpd_tls_session_cache_database = btree:$data_directory/smtpd_tls_session_cache smtpd_tls_security_level = may smtpd_tls_loglevel = 1 #secure smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination Log from mail.log Oct 30 14:51:13 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.109]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:15 webmaster postfix/smtp[9506]: 87E2739400B1: SASL authentication failed; server smtp.gmail.com[74.125.25.109] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 ix9sm156630pbc.7 Oct 30 14:51:15 webmaster postfix/smtp[9506]: setting up TLS connection to smtp.gmail.com[74.125.25.108]:587 Oct 30 14:51:15 webmaster postfix/smtp[9506]: certificate verification failed for smtp.gmail.com[74.125.25.108]:587: untrusted issuer /C=US/O=Equifax/OU=Equifax Secure Certificate Authority Oct 30 14:51:16 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.108]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:17 webmaster postfix/smtp[9506]: 87E2739400B1: to=<[email protected]>, relay=smtp.gmail.com[74.125.25.108]:587, delay=972, delays=967/0.03/5.5/0, dsn=4.7.1, status=deferred (SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) Oct 30 14:51:17 webmaster postfix/error[9508]: B3960394009D: to=<[email protected]>, orig_to=<root>, relay=none, delay=29992, delays=29986/5.6/0/0.07, dsn=4.7.1, status=deferred (delivery temporarily suspended: SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) BTW I made cert follow the link here http://koti.kapsi.fi/ptk/postfix/postfix-tls-cacert.shtml and it worked, but after 2/3 days my email back to problem invalid SASL, and then i'm required to log in use a browser and enter the captcha there but success log in after input captcha, and my email server can send emails from telnet or php script. but it will be back in trouble after 2/3days later. My question is how to make it permanent certificate? Thanks n greeting.

  Read the article

• Cisco VPNClient from Mac won't connect using iPhone Tethering

  - by Dan Short

  I just set up iPhone tethering from my Snow Leopard Macbook Pro to my iPhone 3GS with the Datapro 4GB plan from AT&T. When attempting to connect to my corporate VPN from the MacBook Pro with Cisco VPNClient 4.9.01 (0100) I get the following log information: Cisco Systems VPN Client Version 4.9.01 (0100) Copyright (C) 1998-2006 Cisco Systems, Inc. All Rights Reserved. Client Type(s): Mac OS X Running on: Darwin 10.6.0 Darwin Kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:xnu-1504.9.26~3/RELEASE_I386 i386 Config file directory: /etc/opt/cisco-vpnclient 1 13:02:50.791 02/22/2011 Sev=Info/4 CM/0x43100002 Begin connection process 2 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0AD337FF, Src Addr: 0x0AD33702 (DRVIFACE:1158). 3 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0A2581FF, Src Addr: 0x0A258102 (DRVIFACE:1158). 4 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100004 Establish secure connection using Ethernet 5 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100024 Attempt connection with server "209.235.253.115" 6 13:02:50.792 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (500). 7 13:02:50.793 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (4500). 8 13:02:50.793 02/22/2011 Sev=Info/6 IKE/0x4300003B Attempting to establish a connection with 209.235.253.115. 9 13:02:51.293 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 10 13:02:51.894 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 11 13:02:52.495 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 12 13:02:53.096 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 13 13:02:53.698 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 14 13:02:54.299 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. 16 13:02:54.299 02/22/2011 Sev=Warning/2 IKE/0xC300009A Failed to set up connection data 17 13:02:54.299 02/22/2011 Sev=Info/4 CM/0x4310001C Unable to contact server "209.235.253.115" 18 13:02:54.299 02/22/2011 Sev=Info/5 CM/0x43100025 Initializing CVPNDrv 19 13:02:54.300 02/22/2011 Sev=Info/4 CVPND/0x4340001F Privilege Separation: restoring MTU on primary interface. 20 13:02:54.300 02/22/2011 Sev=Info/4 IKE/0x43000001 IKE received signal to terminate VPN connection 21 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700008 IPSec driver successfully started 22 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 23 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000D Key(s) deleted by Interface (192.168.0.171) 24 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 25 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 26 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 27 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000A IPSec driver successfully stopped The key line is 15: 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. I can't find anything online about this. I found a single entry for the error message in Google, and it was a swedish (or some other nordic language site) that didn't have an answer to the question. I've tried connecting through both USB and Bluetooth tethering to the iPhone, and they both return the exact same results. I don't have direct control over the firewall, but if changes are necessary to make it work, I may be able to get the powers-that-be to make adjustments. A solution that doesn't require reconfiguring the firewall would be far better of course... Does anyone know what I can do to make this behave? Thanks, Dan

  Read the article

• linux routing bug?

  - by Balázs Pozsár

  I have been struggling with this not easily reproducible issue since a while. I am using linux kernel v3.1.0, and sometimes routing to a few IP addresses does not work. What seems to happen is that instead of sending the packet to the gateway, the kernel treats the destination address as local, and tries to gets its MAC address via ARP. For example, now my current IP address is 172.16.1.104/24, the gateway is 172.16.1.254: # ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:1B:63:97:FC:DC inet addr:172.16.1.104 Bcast:172.16.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:230772 errors:0 dropped:0 overruns:0 frame:0 TX packets:171013 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:191879370 (182.9 Mb) TX bytes:47173253 (44.9 Mb) Interrupt:17 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.254 0.0.0.0 UG 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 I can ping a few addresses, but not 172.16.0.59: # ping -c1 172.16.1.254 PING 172.16.1.254 (172.16.1.254) 56(84) bytes of data. 64 bytes from 172.16.1.254: icmp_seq=1 ttl=64 time=0.383 ms --- 172.16.1.254 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.383/0.383/0.383/0.000 ms root@pozsybook:~# ping -c1 172.16.0.1 PING 172.16.0.1 (172.16.0.1) 56(84) bytes of data. 64 bytes from 172.16.0.1: icmp_seq=1 ttl=63 time=5.54 ms --- 172.16.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 5.545/5.545/5.545/0.000 ms root@pozsybook:~# ping -c1 172.16.0.2 PING 172.16.0.2 (172.16.0.2) 56(84) bytes of data. 64 bytes from 172.16.0.2: icmp_seq=1 ttl=62 time=7.92 ms --- 172.16.0.2 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 7.925/7.925/7.925/0.000 ms root@pozsybook:~# ping -c1 172.16.0.59 PING 172.16.0.59 (172.16.0.59) 56(84) bytes of data. From 172.16.1.104 icmp_seq=1 Destination Host Unreachable --- 172.16.0.59 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms When trying to ping 172.16.0.59, I can see in tcpdump that an ARP req was sent: # tcpdump -n -i eth0|grep ARP tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes 15:25:16.671217 ARP, Request who-has 172.16.0.59 tell 172.16.1.104, length 28 and /proc/net/arp has an incomplete entry for 172.16.0.59: # grep 172.16.0.59 /proc/net/arp 172.16.0.59 0x1 0x0 00:00:00:00:00:00 * eth0 Please note, that 172.16.0.59 is accessible from this LAN from other computers. Does anyone have any idea of what's going on? Thanks. update: replies to the comments below: there are no interfaces besides eth0 and lo the ARP req cannot be seen on the other end, but that's how it should work. the main problem is that an ARP req should not even be sent at the first place the problem persist even if I add an explicit route with the command "route add -host 172.16.0.59 gw 172.16.1.254 dev eth0"

  Read the article

• How to understand the memory usage and load average in linux server

  - by Tim

  Hi, I am using a linux server which has 128GB of memory and 24 cores. I use top to see how much it is used. Its output is pasted at the end of the post. Here are two questions: (1) I see that each of the running processes occupies a very small percentage of memory (%MEM no more than 0.2%, and most just 0.0%), but how the total memory is almost used as in the fourth line of output ("Mem: 130766620k total, 130161072k used, 605548k free, 919300k buffers")? The sum of used percentage of memory over all processes seems unlikely to achieve almost 100%, doesn't it? (2) how to understand the load average on the first line ("load average: 14.04, 14.02, 14.00")? Thanks and regards! Edit: Thanks! I also really like to hear some rough numbers based on used percentage of memory to determine if a server is heavily loaded, since I once became the one who cramed the server without understanding the current load. Is swap regarded as almost the same as memory? For example, when memory and swap are almost of same size, if the memory is almost running out but the swap is still largely free, may I just view it as if the used percentage of memory + swap is still not high and run other new processes? How would you consider together CPU or memory (or memory + swap) usage? Do you become worried if either of them reaches too high or both? Output of top: $ top top - 12:45:33 up 19 days, 23:11, 18 users, load average: 14.04, 14.02, 14.00 Tasks: 484 total, 12 running, 472 sleeping, 0 stopped, 0 zombie Cpu(s): 36.7%us, 19.7%sy, 0.0%ni, 43.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 130766620k total, 130161072k used, 605548k free, 919300k buffers Swap: 63111312k total, 500556k used, 62610756k free, 124437752k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 6529 sanchez 18 -2 1075m 219m 13m S 100 0.2 13760:23 MATLAB 13210 timothy 18 -2 48336 37m 1216 R 100 0.0 3:56.75 absurdity 13888 timothy 18 -2 48336 37m 1204 R 100 0.0 2:04.89 absurdity 14542 timothy 18 -2 48336 37m 1196 R 100 0.0 1:08.34 absurdity 14544 timothy 18 -2 2888 2076 400 R 100 0.0 1:06.14 gatherData 6183 sanchez 18 -2 1133m 195m 13m S 100 0.2 13676:04 MATLAB 6795 sanchez 18 -2 1079m 210m 13m S 100 0.2 13734:26 MATLAB 10178 timothy 18 -2 48336 37m 1204 R 100 0.0 11:33.93 absurdity 12438 timothy 18 -2 48336 37m 1216 R 100 0.0 5:38.17 absurdity 13661 timothy 18 -2 48336 37m 1216 R 100 0.0 2:44.13 absurdity 14098 timothy 18 -2 48336 37m 1204 R 100 0.0 1:58.31 absurdity 14335 timothy 18 -2 48336 37m 1196 R 100 0.0 1:08.93 absurdity 14765 timothy 18 -2 48336 37m 1196 R 99 0.0 0:32.57 absurdity 13445 timothy 18 -2 48336 37m 1216 R 99 0.0 3:01.37 absurdity 28990 root 20 0 0 0 0 S 2 0.0 65:50.21 pdflush 12141 tim 18 -2 19380 1660 1024 R 1 0.0 0:04.04 top 1240 root 15 -5 0 0 0 S 0 0.0 16:07.11 kjournald 9019 root 20 0 296m 4460 2616 S 0 0.0 82:19.51 kdm_greet 1 root 20 0 4028 728 592 S 0 0.0 0:03.11 init 2 root 15 -5 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT -5 0 0 0 S 0 0.0 0:01.01 migration/0 4 root 15 -5 0 0 0 S 0 0.0 0:08.13 ksoftirqd/0 5 root RT -5 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT -5 0 0 0 S 0 0.0 17:27.31 migration/1 7 root 15 -5 0 0 0 S 0 0.0 0:01.21 ksoftirqd/1 8 root RT -5 0 0 0 S 0 0.0 0:00.00 watchdog/1 9 root RT -5 0 0 0 S 0 0.0 10:02.56 migration/2 10 root 15 -5 0 0 0 S 0 0.0 0:00.34 ksoftirqd/2 11 root RT -5 0 0 0 S 0 0.0 0:00.00 watchdog/2 12 root RT -5 0 0 0 S 0 0.0 4:29.53 migration/3 13 root 15 -5 0 0 0 S 0 0.0 0:00.34 ksoftirqd/3

  Read the article

• Nginx traffic is going to wrong upsteam when mixing named servers and default servers

  - by Morgan

  I have the below config file for nginx. The problem is all traffic is going to upstream clustera. How do I configure nginx to only send traffic for example.com to clustera and all the rest to clusterb? user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; log_format cache '\n*** $remote_addr [$time_local] ' '[$upstream_cache_status] $upstream_response_time ' '$host "$request" ($status) $body_bytes_sent ' '"$http_referer" "$http_user_agent" ' 'Cache-Control: $upstream_http_cache_control ' 'Expires: $upstream_http_expires ' ; access_log /var/log/nginx/access.log cache; sendfile on; keepalive_timeout 65; gzip on; gzip_vary on; gzip_comp_level 6; gzip_proxied any; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; gzip_buffers 16 8k; include /etc/nginx/conf.d/*.conf; proxy_cache_key "$scheme$host$request_uri"; proxy_cache_path /var/cache/nginx levels=1:2 keys_zone=main:10m max_size=1g inactive=30m; upstream clustera { ip_hash; server a.example.com:80; } upstream clusterb { ip_hash; server b.example.com:80; } client_max_body_size 20m; client_body_buffer_size 128k; proxy_connect_timeout 300; proxy_send_timeout 300; proxy_read_timeout 300; # host for example.com should send traffic to clustera server { listen 80; server_name example.com; location ~*(png|jpeg|jpg|gif|ico|css|js)$ { proxy_pass http://clustera; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_cache main; proxy_cache_valid 200 5m; proxy_cache_valid 302 1m; } location / { proxy_pass http://clustera; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } # host for everyone else. traffic goes to clusterb server { listen 80; server_name _; if ( $http_user_agent ~* (spider|crawler|slurp) ) { return 503; } set $slow 0; if ( $http_user_agent ~* (bot) ) { set $slow 1; } if ( $slow ) { set $limit_rate 1k; } location ~*(png|jpeg|jpg|gif|ico|css|js)$ { proxy_pass http://clusterb; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_cache main; proxy_cache_valid 200 5m; proxy_cache_valid 302 1m; } location /images { proxy_pass http://clisterb; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_cache main; proxy_cache_valid 200 5m; proxy_cache_valid 302 1m; } location / { proxy_pass http://clusterb; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } }

  Read the article

• Windows 7 / Ubuntu Dualboot GRUB Problem.

  - by Tek

  I'd like to first say ahead of time that I'm running a RAID-0 Setup. 1.First of all, I'm glad Ubuntu 9.10 installed flawlessly and detected my RAID-0 setup just fine. The issue I'm having now is that I already had Windows 7 installed and made a small 12GB partition for Linux/Swap. I grabbed EasyBCD 2.0 to edit the W7 bootloader and configured it to use dual boot Grub2 because before it didn't even show the option for Ubuntu. The bootloader points to a file made in the windows directory made by EasyBCD called "C:\NST\AutoNeoGrub0.mbr" which is what I'm guessing grub is booting from. After that I got the option for booting Ubuntu. The problem is that it's sending me to the Grub prompt (probably because it's pointing to \NST|AutoNeoGrub0.mbr?), at first I didn't know what to do but I researched and have to type grub commands to manually boot into Ubuntu Linux. Ex: grubroot (hd0,4) grubkernel /boot/vmlinuz-2.6... root=/dev/disk/by-uuid/24624-2424... grubinitrd boot/initrd.img-2.6... grubboot After all that Ubuntu boots just fine, but how do I fix it permanently? Do I need to edit the bootloader manually (since Easy BCD "autoconfigures")? Some insight on this would rock! Also, it sucks to type the actual uuid since it's REALLY long. I tried getting the name of the drive via fdisk -l but since it's raid 0 I'm guessing I can't do that. How can I get a shorter name of the drive? like /dev/sda, /dev/sdb etc? I've also tried to update to the latest GRUB and I got this: Creating config file /etc/default/grub with new version Generating core.img error: cannot seek /dev/sdc' error: cannot seek/dev/sdc' grub-probe: error: no mapping exists for nvidia_dbedfcca5' Auto-detection of a filesystem module failed. Please specify the module with the option--modules' explicitly. dpkg: error processing grub-pc (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of grub2: grub2 depends on grub-pc; however: Package grub-pc is not configured yet. dpkg: error processing grub2 (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. E: Sub-process /usr/bin/dpkg returned an error code (1) I've also tried: b@dnb:~$ sudo update-grub error: cannot seek /dev/sdc' error: cannot seek/dev/sdc' Generating grub.cfg ... Found linux image: /boot/vmlinuz-2.6.31-14-generic Found initrd image: /boot/initrd.img-2.6.31-14-generic error: cannot seek /dev/sdc' grub-probe: error: no mapping exists fornvidia_dbedfcca5' error: cannot seek /dev/sdc' grub-probe: error: no mapping exists fornvidia_dbedfcca5' Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/mapper/nvidia_dbedfcca1 error: cannot seek /dev/sdc' grub-probe: error: no mapping exists fornvidia_dbedfcca1' done To no avail. Any idea what I can do to fix this mess? :( Edit: This is my disk configuration. b@dnb:~$ sudo df -l Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/nvidia_dbedfcca5 12302232 2744788 8932520 24% / udev 1030288 268 1030020 1% /dev none 1030288 964 1029324 1% /dev/shm none 1030288 92 1030196 1% /var/run none 1030288 0 1030288 0% /var/lock none 1030288 0 1030288 0% /lib/init/rw /dev/sr0 706532 706532 0 100% /media/cdrom0 Note: /dev/mapper/nvidia_dbedfcca5 is my Linux boot partition

  Read the article

• Have to dhclient each restart to access internet

  - by Zeophlite

  So each time I restart my ubuntu server (virtual 10.04, via Xencenter), I have to call dhclient before I can access the internet: http://img813.imageshack.us/i/dhclient.png/ What do I need to change to get internet access automatically? Apologies for posting images, I'm using Xencenter, so I can't copy/paste the console output EDIT:: daniel@workwork:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.69.136 netmask 255.255.255.0 network 192.168.69.0 broadcast 192.168.69.255 gateway 192.168.69.1 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.69.120 dns-search workwork.com.au daniel@workwork:~$ ifconfig eth0 Link encap:Ethernet HWaddr ae:11:14:22:0a:03 inet6 addr: fe80::ac11:14ff:fe22:a03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:85 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10496 (10.4 KB) TX bytes:13086 (13.0 KB) Interrupt:32 Base address:0x6000 eth1 Link encap:Ethernet HWaddr b2:2c:40:f2:a0:fa inet addr:192.168.69.167 Bcast:192.168.69.255 Mask:255.255.255.0 inet6 addr: fe80::b02c:40ff:fef2:a0fa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13448 errors:0 dropped:0 overruns:0 frame:0 TX packets:3100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7679428 (7.6 MB) TX bytes:282286 (282.2 KB) Interrupt:36 Base address:0xa100 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:179 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:36905 (36.9 KB) TX bytes:36905 (36.9 KB) daniel@workwork:/var/lib/dhcp3$ cat dhclient.leases lease { interface "eth1"; fixed-address 192.168.69.167; filename "boot\\x86\\wdsnbp.com"; option subnet-mask 255.255.255.0; option routers 192.168.69.1; option dhcp-lease-time 28800; option dhcp-message-type 5; option domain-name-servers 192.168.69.120,192.168.69.121; option dhcp-server-identifier 192.168.69.120; option dhcp-renewal-time 14400; option dhcp-rebinding-time 25200; option domain-name "workwork.com.au"; renew 5 2011/03/18 07:36:53; rebind 5 2011/03/18 11:35:39; expire 5 2011/03/18 12:35:39; } lease { interface "eth1"; fixed-address 192.168.69.167; filename "boot\\x86\\wdsnbp.com"; option subnet-mask 255.255.255.0; option routers 192.168.69.1; option dhcp-lease-time 28800; option dhcp-message-type 5; option domain-name-servers 192.168.69.120,192.168.69.121; option dhcp-server-identifier 192.168.69.120; option dhcp-renewal-time 14400; option dhcp-rebinding-time 25200; option domain-name "workwork.com.au"; renew 5 2011/03/18 08:51:58; rebind 5 2011/03/18 12:24:16; expire 5 2011/03/18 13:24:16; } daniel@workwork:/var/lib/dhcp3$ cat dhclient.eth0.leases daniel@workwork:/var/lib/dhcp3$ ifconfig eth1 before and after dhclient http://img692.imageshack.us/i/prepost.png/

  Read the article

• redhat Apache fast-cgi selinux permissions

  - by Alejo JM

  My apache installation is running php as fastcgi, and the virtual hosts are pointing to /home/*/public_html. and the fastcgi are home/*/cgi-bin/php.fcgi the public_html setup with selinux was: /usr/sbin/setsebool -P httpd_enable_homedirs 1 chcon -R -t httpd_sys_content_t /home/someuser/public_html The owner and group are the user, for example the user "someuser": ls -all /home/someuser/cgi-bin/ drwxr-xr-x 2 someuser someuser 4096 Sep 7 13:14 . drwx--x--x 6 someuser someuser 4096 Sep 6 18:17 .. -rwxr-xr-x 1 someuser someuser 308 Sep 7 13:14 php.fcgi ls -all /home/someuser/public_html/ | greep info.php -rw-r--r-- 1 someuser someuser 24 Sep 3 16:24 info.php When is visits the site I get "Forbidden ..." and the log said: [Fri Sep 07 12:02:51 2012] [error] [client x.x.x.x] (13)Permission denied: access to /cgi-bin/php.fcgi/info.php denied My selinux conf is: SELINUX=enforcing SELINUXTYPE=targeted SETLOCALDEFS=0 So I kill Selinux (SELINUX=disabled), reboot the system and everything works !!!!! The problem is Selinux, I don't want disable Selinux. I trying this with no success: setsebool -P httpd_enable_cgi 1 chcon -t httpd_sys_script_exec_t /home/someuser/cgi-bin/php.fcgi chcon -R -t httpd_sys_content_t /home/someuser/cgi-bin Or maybe is better change Selinux SELINUX=enforcing to SELINUX=permissive And disable selinux for httpd ? (I think I better find the correct configuration) Thanks for any suggestion on this matter My environment: Red Hat Enterprise Linux Server release 5.8 (Tikanga) Server version: Apache/2.2.3 PHP 5.1.6 (cli) (built: Jun 22 2012 06:20:25) Copyright (c) 1997-2006 The PHP Group Zend Engine v2.1.0, Copyright (c) 1998-2006 Zend Technologies Some logs: ps -ZC httpd LABEL PID TTY TIME CMD system_u:system_r:httpd_t 2822 ? 00:00:00 httpd system_u:system_r:httpd_t 2823 ? 00:00:00 httpd system_u:system_r:httpd_t 2824 ? 00:00:00 httpd system_u:system_r:httpd_t 2825 ? 00:00:00 httpd system_u:system_r:httpd_t 2826 ? 00:00:00 httpd system_u:system_r:httpd_t 2836 ? 00:00:00 httpd system_u:system_r:httpd_t 2837 ? 00:00:00 httpd system_u:system_r:httpd_t 2838 ? 00:00:00 httpd system_u:system_r:httpd_t 2839 ? 00:00:00 httpd system_u:system_r:httpd_t 2840 ? 00:00:00 httpd getsebool -a | grep httpd allow_httpd_anon_write --> off allow_httpd_bugzilla_script_anon_write --> off allow_httpd_cvs_script_anon_write --> off allow_httpd_mod_auth_pam --> off allow_httpd_nagios_script_anon_write --> off allow_httpd_prewikka_script_anon_write --> off allow_httpd_squid_script_anon_write --> off allow_httpd_sys_script_anon_write --> off httpd_builtin_scripting --> on httpd_can_network_connect --> off httpd_can_network_connect_db --> off httpd_can_network_relay --> off httpd_can_sendmail --> on httpd_disable_trans --> off httpd_enable_cgi --> on httpd_enable_ftp_server --> off httpd_enable_homedirs --> on httpd_execmem --> off httpd_read_user_content --> off httpd_rotatelogs_disable_trans --> off httpd_setrlimit --> off httpd_ssi_exec --> off httpd_suexec_disable_trans --> off httpd_tty_comm --> on httpd_unified --> on httpd_use_cifs --> off httpd_use_nfs --> off

  Read the article

• Iptables blocking mysql port 3306

  - by valmar

  I got a Tomcat server running a web application that must access a mysql server via Hibernate on the same machine. So, I added a rule for port 3306 to my iptables script but tomcat cannot connect to the mysql server for some reason. I need to reset all iptables rules - Then tomcat can connect to the mysql server again. All the other iptables rules work perfectly though. What's wrong? Here is my script: iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp --dport 24 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp -s localhost --dport 8009 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -d localhost --dport 8009 -j ACCEPT iptables -A INPUT -p tcp -s localhost --dport 3306 -j ACCEPT iptables -A OUTPUT -p tcp -d localhost --dport 3306 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A OUTPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp --dport 25 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 25 -j ACCEPT iptables -A INPUT -p tcp --dport 587 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 587 -j ACCEPT iptables -A INPUT -p tcp --dport 465 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 465 -j ACCEPT iptables -A INPUT -p tcp --dport 110 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 110 -j ACCEPT iptables -A INPUT -p tcp --dport 995 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 995 -j ACCEPT iptables -A INPUT -p tcp --dport 143 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 143 -j ACCEPT iptables -A INPUT -p tcp --dport 993 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 993 -j ACCEPT iptables -A INPUT -j DROP My /etc/hosts file: # nameserver config # IPv4 127.0.0.1 localhost 46.4.7.93 mydomain.com 46.4.7.93 Ubuntu-1004-lucid-64-minimal 46.4.7.93 horst # IPv6 ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts Having a look into the iptables logs, gives me this: Jun 22 16:52:43 Ubuntu-1004-lucid-64-minimal kernel: [ 435.111780] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=52432 DF PROTO=TCP SPT=56108 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:46 Ubuntu-1004-lucid-64-minimal kernel: [ 438.110555] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=52433 DF PROTO=TCP SPT=56108 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:46 Ubuntu-1004-lucid-64-minimal kernel: [ 438.231954] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=48020 DF PROTO=TCP SPT=56109 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:49 Ubuntu-1004-lucid-64-minimal kernel: [ 441.229778] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=48021 DF PROTO=TCP SPT=56109 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:53:57 Ubuntu-1004-lucid-64-minimal kernel: [ 508.731839] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=78.92.97.67 DST=46.4.7.93 LEN=64 TOS=0x00 PREC=0x00 TTL=122 ID=23053 DF PROTO=TCP SPT=1672 DPT=445 WINDOW=65535 RES=0x00 SYN URGP=0 Jun 22 16:53:59 Ubuntu-1004-lucid-64-minimal kernel: [ 511.625038] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=78.92.97.67 DST=46.4.7.93 LEN=64 TOS=0x00 PREC=0x00 TTL=122 ID=23547 DF PROTO=TCP SPT=1672 DPT=445 WINDOW=65535 RES=0x00 SYN URGP=0 Jun 22 16:54:22 Ubuntu-1004-lucid-64-minimal kernel: [ 533.981995] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=27.254.39.16 DST=46.4.7.93 LEN=48 TOS=0x00 PREC=0x00 TTL=117 ID=6549 PROTO=TCP SPT=6005 DPT=33796 WINDOW=64240 RES=0x00 ACK SYN URGP=0 Jun 22 16:54:44 Ubuntu-1004-lucid-64-minimal kernel: [ 556.297038] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=94.78.93.41 DST=46.4.7.93 LEN=40 TOS=0x00 PREC=0x00 TTL=52 ID=7712 PROTO=TCP SPT=57598 DPT=445 WINDOW=512 RES=0x00 SYN URGP=0

  Read the article

< Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >