Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 296/750 | < Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >

  • Exchange 2010 global auto reply - hub transport rules?

    - by RodH257
    Our office is closing for the holidays, and I want to setup an auto reply if anyone attempts to email. Rather than get everyone to do it individually I want to set a blanket message on the Exchange 2010 server. Looking around here I found hub transport rules can be used, but I don't want to send a rejection message, like in this post I want to keep the message but just say that we won't get back to you fora couple of weeks. Can anyone point me in the right direction?

    Read the article

  • Cannot install grub to RAID1 (md0)

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

    Read the article

  • Vista ICS with ubuntu?

    - by user25427
    I have still have dial-up(cant afford highspeed) and I am trying to configure my desktop with vista to share that connection with Ubuntu Ive got it all setup but ubuntu wont get on the internet at all. Can yall help me with this problem.

    Read the article

  • What are the ideal settings for a Belkin WiFi Router to connect to an iPhone? [closed]

    - by user34833
    The Belkin Router (F5D8235-4 v2000) has numerous options in the setup. These are the current settings: Wireless On SSID Buster's Special Security Type WPA Encryption Type TKIP WLAN MAC Address 00:22:75:B3:58:38 WPS Enabled Guest Access Disabled SSID Belkin_N+_Guest Password/PSK NotThatSillyYet :) The iPhone is a 3g with 16GB it has no problems connecting to public networks like libraries or restaurants. But currently it won't connect to my home WiFi. Thanks for your time and help. Paul

    Read the article

  • Operative systems on SD cards

    - by HisDudeness
    I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

    Read the article

  • What's a good (preferably standard) was to restore iptables config in ubuntu 9.10

    - by nixomose
    I never quite got why this isn't some built in setup, although maybe it is and stuff changes so quickly I just missed it. I can use iptables-save to generate something I can feed into iptables-restore, but what I was wondering is if there was a standard place to put it so that it gets picked up on boot without me having to add something to rc.local or the ever changing init/event.d scripts.

    Read the article

  • Can Azure host ColdFusion?

    - by mbursill
    A friend has a site developed in ColdFusion with MySQL and is looking for better cost-effective hosting as the traffic scales up rapidly. Azure comes to mind. I haven't used Azure myself, however, I believe it is possible to setup and interact with the web-server via RDP into a hosted Virtual Machine? I am curious if ColdFusion can be installed in the hosted Azure VM. Also, would the site have to be tweaked to run on Azure SQL, or could it continue to use MySQL? Thanks.

    Read the article

  • I need help installing Autokey in CentOS

    - by Kevin Lee
    PLease teach me how to do it, here's the INSTALL file of the autokey folder: This application requires a full Debian package build - it cannot be installed using only the setup.py script: dpkg-buildpackage -us -uc cd ../ For GNOME: sudo dpkg -i autokey-gtk_.deb autokey-common_.deb For KDE: sudo dpkg -i autokey-qt_.deb autokey-common_.deb I'm using CentOS, I don't have any idea how to install this.. Here's the FAQ page of the Autokey application: http://code.google.com/p/autokey/wiki/FAQ Please help me install this.. Thanks!

    Read the article

  • Grub problem with dual boot Ubuntu & XP (Ubuntu installed first)

    - by c00lryguy
    I had Ubuntu installed and I installed XP. I tried to be able to dual boot them by running an Ubuntu live cd and running ~ $ sudo grub grub> root (hd0,0) grub> setup (hd0) But now when I restart I get a black screen that says 'Boot device Selected Boot Device and press any key No matter what key I press it shows this error This is what my system looks like: /dev/sda1 - Ubuntu - ext3 - 73 GiB /dev/sda2 - Ubuntu - extended - 3.16 GiB /dev/sda5 - Ubuntu - linux-swap - 3.16 GiB /dev/sdb1 - Windows XP - ntfs - 76 GiB /dev/sdc1 - Stuff - ext3 - Code/Documents /dev/sdd2 - Stuff - ext3 - Movies/Music

    Read the article

  • Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

    - by Anon
    We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

    Read the article

  • How do I uninstall MySQL on Mac OS X (Snow Leopard)?

    - by Abhic
    I had installed MySQL from the command line when I setup a local web server with custom modules on my Snow Leopard box. I recently discovered MAMP and its just easier to work with it than with the personal web server Apple has and via command like utils. I uninstall ports completely but still see 'mysqld' in my Activity Monitor. I would like to uninstall this cleanly. Any tips?

    Read the article

  • PAM / LDAP authentication with Ubuntu 10.04

    - by t6d
    I can't wrap my brain around the new pam.d configuration syntax used in Ubuntu 10.04. How do I setup PAM so that it allows users stored in my LDAP database to login. I already configured nscd, so id <user> or getent passwd are already listing my LDAP users, but PAM doesn't work, whether the normal shell login nor su.

    Read the article

  • Identify OpenVZ virtual machine from inside

    - by Alfred Godoy
    Is there any way for me to identify which OpenVZ container I am in, from inside the container? I am working on a setup where OpenVZ machines shall boot the same (read-only) disk image, so I can not configure them individually in the file system. I need a unique identification for each of the virtual servers, to be used by scripts running inside the OpenVZ containers. (I'm running Debian Lenny, BTW.)

    Read the article

  • Activation of Bootcamped Windows 7 in VMWare Fusion'?

    - by Lurker
    Hello, I have bought a boxed version of Windows 7 Home Premium (not OEM). I want to install this on new iMac via bootcamp but I also want to use this Bootcamped partition via VMWare Fusion. VMWare fusion has article about activating bootcamped windows installation. Does this work setup work for you?

    Read the article

  • Wireless router DSL connection problem help

    - by infoquad
    I recently bought a wireless DSL router to replace my wired one. After quick setup however, the router does not connect to the Internet. Wireless connection between laptop and router exists and Internet can be connected through laptop(manually) by using router as WAN miniport(PPPoE). What I want to do is connect the wireless router to Internet so that when laptop connects to router, I can start using the Internet. How do I do this? Please help.

    Read the article

  • Managing multiple independant domains with Google Apps

    - by Saif Bechan
    I am currently running a server where I have multiple domains with all of them running there own mail server. My plan is to outsource this whole email service and have Google, or competitor, do this for me. Let me start by telling you the setup I have now and want to migrate to Google. Initial setup I have a main domain where I run my server, and my nameserver. This is an important domain because this holds the connection with all my internal applications. For example log messages, cronjob messages, and virus-scan messages are sent to this domain. This email is also registered at my registrar and I use it to communicate with my ISP. Next I run a few independent websites that all need their independent email addresses. This can be on shared space, I don't mind. 1 Gig will be enough for everything I am going to do. Summary: superdomain.com (which only has a catchall for internal use and communication with my ISP) cars.com (independent) flowers.com (independent) foods.com (independent) I am going to be the admin for all of this. The independent domains don't need there own admin panel, they just need email addresses like info@ support@, etc. I do all the managing and they just send and receive emails using the accounts i give them. All of the websites have there different staff that use the accounts. Tried so far I have registered my superdomain, but I can only add aliases to the main domain. If I make all the other domains aliases the emails from [email protected] and [email protected] will have the same inbox. I want them to be separate. is the only way to achieve this by creating an account for each domain? And if so, is there no way of creating a superdomain account where I can edit all these accounts easily without having to log in 4 different places to get my work done. I have searched the Google help forums, and posted questions but without any results so far. Questions Can anyone please give me some advice on what to do. I currently use the free program Google has.

    Read the article

  • Bash Shell Scripting - How to iterate through directories, and copy and rename files?

    - by Cypher
    I have a directory setup as follows: /hosted/partner1/logo.png /hosted/partner2/logo.png /hosted/partner3/logo.png /hosted/partner4/logo.png /hosted/partner5/logo.png ..etc. I want to write a script that can COPY those files to a different location, with a different file name, like this: /partners/partner1.png /partners/partner2.png /partners/partner3.png ..etc. Any ideas? I'm not so great with shell scripting and there are a lot of files that I need to migrate to a single directory...

    Read the article

  • Tomato VPN connect but cannot ping LAN IP

    - by David Hamilton
    I've setup TomatoVPN using these settings on the server: TAP UDP 1194 Client address pool 10.10.9.1 -10.10.9.254 LAN clients are configured with 10.10.10.x I can connect from a remote client, but pinging anything in the 10.10.10.x results in a "Destination Host Unreachable" error. Here's my client configuration script: remote x.x.x.x 1194 client dev tap0 proto udp resolv-retry infinite nobind persist-key persist-tun float ca ca.crt cert client1.crt key client1.key ns-cert-type server Any suggestions as how I can make this properly bridge the two networks?

    Read the article

  • Simple Voip server for ubuntu

    - by Stalkerh
    I have a network that connects 2 households and would like to setup a simple voip server so that I can call between the houses. It needs to be for ubnutu , I have used the free 3CX system and while it works brilliantly it doesnt support linux and I can get a windows box. The users will never need to call external lines. They will only make 'calls' between laptops/pc. Can someone please make a recommendation and maybe even a tutorial that I can follow

    Read the article

  • htaccess allow if does not contain string

    - by Tom
    I'm trying to setup a .htaccess file which will allow users to bypass the password block if they come from a domain which does not start with preview. e.g. http://preview.example.com would trigger the password and http://example.com would not. Here's what I've got so far: SetEnvIfNoCase Host preview(.*\.)? preview_site AuthUserFile /Users/me/.htpasswd AuthGroupFile /dev/null AuthType Basic AuthName "Development Area" Require valid-user Order deny,allow Allow from 127 deny from env=preview_site Satisfy any Any ideas?

    Read the article

  • UCEProtect Level 3 - Emails land in SPAM

    - by preetam
    I am not sure how i can have remove the IP from UCEPROTECT Level 3. Or a way in which i can send emails without them landing into spam. The IP which i have used has only sent emails to the users which they have asked for and naturally not listed for spamming. But the Service provider is. Any suggestion?, as i don't see the institution for which the setup has been made would change the ISP at this stage. Thank You

    Read the article

  • Is there any problem using the ftpd that comes with Kerberos on CentOS?

    - by Chen Levy
    Hello, I need to configure ftpd on a CentOS 5.3 host to allow anonymous ftp (upload and download) from a well defined directory. I wish the setup to be as simple as possible, and to introduce as little new dependencies as possible. Scanning the current server configuration, I found the ftpd server that comes as part of the Kerberos workstation: > rpm -ql krb5-workstation | grep ftpd$ /usr/kerberos/sbin/ftpd Is there any reason I could or should not use this ftp server?

    Read the article

< Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >