Search Results

Search found 541 results on 22 pages for 'squeeze my lime'.

Page 3/22 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Creating a partitioned raid1 array for booting a debian squeeze system

    - by gucki
    I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

    Read the article

  • OSS4 on Debian Squeeze

    - by mit
    Hi, I am trying to get OSS4 to work on a Debian Squeeze 64 bit machine with an usb sound adapter. There is no sound from this adapter at the present, although it worked just before on the previous installation. You can see the output of some commands here: $ sudo /etc/init.d/oss4-base restart Stopping Open Sound System: SNDCTL_MIX_EXTINFO: No such device or address done. Starting Open Sound System: done (OSS is already loaded). $ sudo /etc/init.d/oss4-base stop Stopping Open Sound System: SNDCTL_MIX_EXTINFO: No such device or address done. $ sudo /etc/init.d/oss4-base start Starting Open Sound System: done (OSS is already loaded). $ ossinfo Version info: OSS 4.2 (b 2002/201001250441) (0x00040100) GPL Platform: Linux/x86_64 2.6.32-5-xen-amd64 #1 SMP Fri Dec 10 17:41:50 UTC 2010 (pc11) Number of audio devices: 2 Number of audio engines: 2 Number of MIDI devices: 0 Number of mixer devices: 2 Device objects 0: osscore0 OSS core services 1: oss_hdaudio0 ATI HD Audio interrupts=0 (613) HD Audio controller ATI HD Audio Vendor ID 0x10024383 Subvendor ID 0x10192816 Codec 0: Not present 2: oss_usb0 USB audio core services 3: usb0d8c0126-0 USB sound device 4: usb0d8c0126-1 USB sound device 5: usb0d8c0126-2 USB sound device 6: usb0d8c0126-3 USB sound device MIDI devices (/dev/midi*) Mixer devices 0: (USB sound device )(Mixer 0 of device object 3) 1: USB sound device (Mixer 0 of device object 5) Audio devices (USB sound device play /dev/oss/usb0d8c0126-1/pcm0 ) (device index 0) USB sound device play /dev/oss/usb0d8c0126-3/pcm0 (device index 1) Nodes /dev/dsp -> /dev/oss/usb0d8c0126-1/pcm0 /dev/dsp_out -> /dev/oss/usb0d8c0126-1/pcm0 /dev/dsp_mmap -> /dev/oss/usb0d8c0126-1/pcm0 $ osstest Sound subsystem and version: OSS 4.2 (b 2002/201001250441) (0x00040100) Platform: Linux/x86_64 2.6.32-5-xen-amd64 #1 SMP Fri Dec 10 17:41:50 UTC 2010 *** Scanning sound adapter #-1 *** /dev/oss/usb0d8c0126-1/pcm0 (audio engine 0): USB sound device play - Device not present - Skipping *** Scanning sound adapter #-1 *** /dev/oss/usb0d8c0126-3/pcm0 (audio engine 1): USB sound device play - Performing audio playback test... /dev/oss/usb0d8c0126-3/pcm0: No such file or directory Can't open the device *** Some errors were detected during the tests *** $ ossxmix /dev/oss/usb0d8c0126-2/mix0: No such file or directory No mixers could be opened $ ossmix SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossmix -a SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossmix -D SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ ossmix -D 0 SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossxmix /dev/oss/usb0d8c0126-2/mix0: No such file or directory No mixers could be opened How can I make oss sound work? I can add more information if necessary.

    Read the article

  • Bootstrap a debian build environment and build source packages with no root privileges

    - by Erwan Queffélec
    On debian squeeze, I am trying to do the following : fetch sources package from the wheezy source repository bootstrap a squeeze chroot for several architectures build the packages for several architectures (i386, amd64 + all and any) I want both the fetching, bootstrapping and build operation to be scriptable, repeatable, and run as a normal user. For the environment setup, I want to make as little use of the root account as possible (install the necessary dependencies, and maybe some visudo stuff). If possible I would like to avoid using a VM (pbuilder with user mode linux) So far I have tried several things with pbuilder (require root), debootstrap (require root) with little success. Here is an example script of what I want to do (does not work): #/bin/bash set -e set -x this=`readlink -f $0` this_dir=`dirname $this` archs='i386 amd64 any all' pushd $this_dir/src # I actually want the following line to work with a repo that # is not in /etc/apt/sources.list but that is another question apt-get source cyrus-imapd-2.4 popd for arch in $archs do build_dir=$this_dir/build/$arch/ pbuilder --create --configfile $build_dir/pbuilderrc --buildresult $build_dir/ pbuilder --build --configfile $build_dir/pbuilderrc --buildresult \ $build_dir/ $this_dir/src/*.dsc # of course I want to use the .dput.cf in /home/myuser/ # and not in /root/ dput $build_dir/$arch/*.changes done

    Read the article

  • NFS-Root not working when booting over PXE

    - by Randy
    I am desperately trying to get a diskless client running over PXE-Boot using a NFS-Share as a root file system. I did this before some years ago but for some reason I am stucked at this since days. The TFTP-Server itself is running fine and booting a netinstaller works also fine. The kernel and initrd are loaded also but the bootprocess stops with this (screenshot) kernel panic. I'm using the squeeze standard i386-Kernel and I have prepared the initrd with this config: MODULES=most BUSYBOX=y KEYMAP=n COMPRESS=gzip BOOT=nfs DEVICE= NFSROOT=auto I also tried MODULES=netboot with the same outcome. My PXE-configuration looks like this: LABEL linux KERNEL diskless/debian-default/vmlinuz-2.6.32-5-686 APPEND root=/dev/nfs initrd=diskless/debian-default/vmlinuz-2.6.32-5-686 nfsroot=192.168.140.2:/storage/nfs-boot-images/default-squeeze ip=dhcp rw Furthermore I have captured the network communication of the client via tcpdump and learned that the client isn't even trying to connect to the NFS-share. Does anybody has got an idea what is going wrong here?

    Read the article

  • How to update debian dns server? New VM with same hostname as old VM

    - by opensourcechris
    We run several linux VM's on our Hyper-V cluster. Our old IT manager configured the dns server to resolve the url 'devlabs.ourdomain.com' to a debian squeeze apache webserver hosted on the hyper v cluster with the hostname: devlabs. We recently created a new Ubuntu vm to replace the original squeeze vm. When we created the new Ubuntu VM we used the same hostname of 'devlabs" to name the new VM. My problem is that now I am only able to access the new Ubuntu VM by using the IP address. How can I update our DNS server to point the url 'devlabs.ourdomain.com' to the new VM?

    Read the article

  • Xen PV packet loss

    - by Delphinator
    I'm having some serious issues with packetloss with one of my servers. This server is a somewhat old (P4-era) machine running Debian Squeeze and Xen 4.0. There are two domUs running on it (both also Debian Squeeze), one gateway and a fileserver. Unfortunatly the processor has no virtualization extensions, therefore only PV can be used. While investigating why our network seems to be slower than it should I found some pretty bad packet loss (~25%). After further investigation and several experiments I did a measurment between the dom0 and one of the domUs: Server listening on UDP port 5001 Receiving 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ ------------------------------------------------------------ Client connecting to dom0, UDP port 5001 Sending 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.2(domU) port 33817 connected with 192.168.1.100(dom0) port 5001 [ 4] local 192.168.1.2(domU) port 5001 connected with 192.168.1.100(dom0) port 48606 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 46.3 MBytes 38.7 Mbits/sec [ 3] Sent 33020 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 46.2 MBytes 38.6 Mbits/sec 0.030 ms 89/33019 (0.27%) [ 3] 0.0-10.0 sec 1 datagrams received out-of-order [ 4] 0.0-10.2 sec 43.0 MBytes 35.3 Mbits/sec 13.074 ms 11575/42256 (27%) tl;dr: 27% packet loss from dom0 to domU with 50Mbit UDP packets. Same thing happens from anywhere in the network. The problem gets better for smaller bandwidths (0.047% for 5Mbit) and worse for higher (59% for 200Mbit) ones. I did increase the CPU-weight of the dom0, there is no swapping going on, and actual networking-hardware is not involved. I never expected Xen (or anything related) to drop packets, and I'm completly clueless what to try next.

    Read the article

  • Apache 2.2 + mod_fcgid + PHP 5.4: (104) Connection reset by peer

    - by Michele Piccirillo
    On a Debian 6 VPS, I'm running PHP 5.4 via mod_fcgid on a couple of different virtual hosts, managed by Virtualmin GPL. At random, I get 500 Internal Server Errors; restarting Apache brings everything back to normality. Examining the logs, I find messages of this kind: [Thu Oct 04 15:39:35 2012] [warn] [client 173.252.100.117] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Thu Oct 04 15:39:35 2012] [error] [client 173.252.100.117] Premature end of script headers: index.php Any ideas about what is happening? UPDATE: I found a similar question and the author reported to have solved the problem disabling APC. I tried following the advice, but I'm still getting the same errors. VirtualHost configuration SuexecUserGroup "#1000" "#1000" ServerName example.com DocumentRoot /home/example/public_html ScriptAlias /cgi-bin/ /home/example/cgi-bin/ DirectoryIndex index.html index.htm index.php index.php4 index.php5 <Directory /home/example/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks +ExecCGI allow from all AllowOverride All AddHandler fcgid-script .php AddHandler fcgid-script .php5 FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php5 </Directory> <Directory /home/example/cgi-bin> allow from all </Directory> RemoveHandler .php RemoveHandler .php5 IPCCommTimeout 61 FcgidMaxRequestLen 1073741824 php5.fcgi #!/bin/bash PHPRC=$PWD/../etc/php5 export PHPRC umask 022 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=99999 export PHP_FCGI_MAX_REQUESTS SCRIPT_FILENAME=$PATH_TRANSLATED export SCRIPT_FILENAME exec /usr/bin/php5-cgi Package versions webmin-virtual-server/virtualmin-universal 3.94.gpl-2 apache2/squeeze 2.2.16-6+squeeze8 libapache2-mod-fcgid/squeeze 1:2.3.6-1+squeeze1 php5 5.4.7-1~dotdeb.0 php5-apc 5.4.7-1~dotdeb.0

    Read the article

  • Exim 4 Virtual Domains and Catchall on Debian (Squeeze)

    - by parazuce
    Hello, I've been at it for about 4 hours now. Searching as well as trying different tutorials. Here's my setup: I have 2 domains, both under my own DNS server (MX records setup as well). I have exim4 successfully running, and it is able to send messages from both of those domains. I have tested this using sendmail, and manually setting the "From" attribute. Exim successfully delivers mail to users no matter which domain was specified. I'm fine with that, but I'm having an issue editing virtual domains, and adding custom delivery options (such as a catch all). I've been searching for about 4 hours, and I can't find any up-to-date documentation on how to do this. The old methods would be to add a line such as: domainlist local_domains = @:localhost:dsearch;/etc/exim4/virtual Once that line was added, I made a directory at /etc/exim4/virtual, then created files inside such as example.com which would then contain rules for delivery under that domain. This did not work, however. Searching further, I've found that exim no longer supports dsearch (I guess because they claim it never has?) This is where I'm stuck. I'm on a "split" configuration as well.

    Read the article

  • Debian Lenny to Debian Squeeze upgrade problems

    - by Roland Soós
    Hi! Yesterday I made a dist-upgrade on my Debian Lenny server. I thought it will be easy as an usual upgrade, but it's not. I got a lot of problem after the update: # apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: linux-image-2.6-amd64 : Depends: linux-image-2.6.32-5-amd64 but it is not installed E: Unmet dependencies. Try using -f. Then I tried the suggestion: # apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libio-compress-base-perl libatk1.0-0 libts-0.0-0 libmime-types-perl libc-client2007b libgtk2.0-common libxfixes3 libgsf-1-common hicolor-icon-theme libfile-remove-perl libxcomposite1 libltdl3-dev libneon27 libmd5-perl libwmf0.2-7 libilmbase6 libatk1.0-data djvulibre-desktop libdirectfb-1.0-0 fam libxinerama1 libcroco3 libopenexr6 libgsf-1-114 libmail-box-perl libdjvulibre21 openssl-blacklist librsvg2-2 libio-compress-zlib-perl libsysfs2 libbeecrypt6 libxdamage1 libobject-realize-later-perl libuser-identity-perl libgtk2.0-bin libxi6 libxcursor1 portmap libxrandr2 libgtk2.0-0 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: linux-image-2.6.32-5-amd64 Suggested packages: linux-doc-2.6.32 The following NEW packages will be installed: linux-image-2.6.32-5-amd64 0 upgraded, 1 newly installed, 0 to remove and 121 not upgraded. 98 not fully installed or removed. Need to get 0 B/28.6 MB of archives. After this operation, 103 MB of additional disk space will be used. Do you want to continue [Y/n]? y perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Preconfiguring packages ... (Reading database ... 37915 files and directories currently installed.) Unpacking linux-image-2.6.32-5-amd64 (from .../linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb) ... locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r dpkg: error processing /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb (--unpack): failed in write on buffer copy for backend dpkg-deb during `./lib/modules/2.6.32-5-amd64/kernel/sound/pci/hda/snd-hda-codec-realtek.ko': No space left on device configured to not write apport reports dpkg-deb: subprocess paste killed by signal (Broken pipe) locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Running postrm hook script /sbin/update-grub. Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.26-2-amd64 Updating /boot/grub/menu.lst ... done Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 2.6.32-5-amd64 /boot/vmlinuz-2.6.32-5-amd64 Errors were encountered while processing: /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) # dpkg-reconfigure locales perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r /usr/sbin/dpkg-reconfigure: locales is broken or not fully installed Then I stucked. Do you have any idea how could I solve this?

    Read the article

  • Debian Squeeze locale settings

    - by regularfry
    I have a problem with a slightly customised Debian image that I'm trying to do some headless work on. The problem is that the installed locales list has been reduced to this: C en_GB en_GB.iso88591 en_GB.iso885915 en_GB.utf8 POSIX However, when I log in as root (with an otherwise as-vanilla profile), I find this: ~# set | grep LC_ LC_CTYPE=en_US.UTF-8 That's the only LC_ environment variable set, and presumably that means that it's being explicitly set somewhere (and given that /etc/default/locale only contains LANG=en_GB, I can't see any other alternative). However, I can't see where it is being set, and the fact that it's wrong is preventing, for example, postgresql-8.4 from installing. I know I can do an LC_CTYPE=en_GB apt-get install postgresql-8.4 to work around this, but I'd really like to understand where this setting comes from, and I really dislike the idea of installing an otherwise-unnecessary locale to make this go away. So: where does this LC_CTYPE setting come from, and how do I make it go away?

    Read the article

  • IRQ problem with 2.6.32/2.6.39 kernel on Debian Squeeze x86_64

    - by MasterM
    I recently assembled a new computer so that all hardware is pretty new. Since then I've been experiencing some problem with IRQs when running Debian 6.0. On random occasions, usually after an hour or so of running I hear a beep and this shows up in dmesg: [ 3537.762795] irq 16: nobody cared (try booting with the "irqpoll" option) [ 3537.762797] Pid: 0, comm: swapper Tainted: P W O 2.6.39-2-amd64 #1 [ 3537.762798] Call Trace: [ 3537.762799] <IRQ> [<ffffffff810924d4>] ? __report_bad_irq+0x3a/0xa2 [ 3537.762803] [<ffffffff810926a4>] ? note_interrupt+0x168/0x1da [ 3537.762805] [<ffffffff81090dd4>] ? handle_irq_event_percpu+0x171/0x18f [ 3537.762807] [<ffffffff8100e0e2>] ? read_tsc+0x5/0x16 [ 3537.762809] [<ffffffff8106b8a2>] ? update_ts_time_stats+0x32/0x6b [ 3537.762810] [<ffffffff81090e26>] ? handle_irq_event+0x34/0x52 [ 3537.762812] [<ffffffff81063fb7>] ? sched_clock_idle_wakeup_event+0x12/0x1c [ 3537.762813] [<ffffffff81092df2>] ? handle_fasteoi_irq+0x82/0xa4 [ 3537.762815] [<ffffffff8100aadb>] ? handle_irq+0x1a/0x23 [ 3537.762816] [<ffffffff8100a384>] ? do_IRQ+0x45/0xaa [ 3537.762818] [<ffffffff81332c93>] ? common_interrupt+0x13/0x13 [ 3537.762818] <EOI> [<ffffffff81332c8e>] ? common_interrupt+0xe/0x13 [ 3537.762821] [<ffffffff81026800>] ? native_safe_halt+0x2/0x3 [ 3537.762829] [<ffffffffa016ed58>] ? acpi_idle_do_entry+0x39/0x62 [processor] [ 3537.762831] [<ffffffffa016edde>] ? acpi_idle_enter_c1+0x5d/0xad [processor] [ 3537.762834] [<ffffffff81261033>] ? cpuidle_idle_call+0x11f/0x1cc [ 3537.762835] [<ffffffff81008dd2>] ? cpu_idle+0xab/0xe1 [ 3537.762837] [<ffffffff8169fc60>] ? start_kernel+0x3e0/0x3eb [ 3537.762838] [<ffffffff8169f3c8>] ? x86_64_start_kernel+0x102/0x10f [ 3537.762839] handlers: [ 3537.762840] [<ffffffffa0358d5a>] (rtl8169_interrupt+0x0/0x2d7 [r8169]) [ 3537.762842] [<ffffffffa08ff2ca>] (nv_kern_isr+0x0/0x54 [nvidia]) [ 3537.762902] Disabling IRQ #16 After that Xorg either hogs on CPU or is unstable (up to hanging the system completely). When I restart Xorg everything is fine again and the problem doesn't occur until next reboot. I tried to upgrade the kernel from stock 2.6.32 to 2.6.39 from unstable repository but that didn't help. Booting with irqpoll option only seems to prolong the initial time period after which the problem occurs. I'm using latest NVIDIA drivers and Realtek firmware from firmware-realtek package. I have two GTX 560Ti that run in SLI. Disabling SLI or taking out one card completely doesn't solve the problem either. Output of uname -a is: Linux whitestar 2.6.39-2-amd64 #1 SMP Wed Jun 8 11:01:04 UTC 2011 x86_64 GNU/Linux Output of lspci is: 00:00.0 Host bridge: Intel Corporation Sandy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:01.1 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 3 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.6 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Cougar Point LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1200 (rev a1) 01:00.1 Audio device: nVidia Corporation Device 0e0c (rev a1) 02:00.0 VGA compatible controller: nVidia Corporation Device 1200 (rev a1) 02:00.1 Audio device: nVidia Corporation Device 0e0c (rev a1) 04:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) 06:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) 07:00.0 PCI bridge: Device 1b21:1080 (rev 01) 08:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10) 08:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Contents of /proc/interrupts: CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 0: 77 0 0 0 0 0 0 0 IO-APIC-edge timer 1: 2 0 0 0 0 0 0 0 IO-APIC-edge i8042 8: 1 0 0 0 0 0 0 0 IO-APIC-edge rtc0 9: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi 12: 4 0 0 0 0 0 0 0 IO-APIC-edge i8042 16: 699083 0 0 0 0 0 0 0 IO-APIC-fasteoi nvidia, eth0 17: 87810 0 0 0 0 0 0 0 IO-APIC-fasteoi firewire_ohci, hda_intel, nvidia 18: 242 0 0 0 0 0 0 0 IO-APIC-fasteoi hda_intel 23: 85925 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb5, ehci_hcd:usb6 40: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 41: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 42: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 43: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 44: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 45: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 46: 79853 0 0 0 0 0 0 0 PCI-MSI-edge ahci 48: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 49: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 50: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 51: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 52: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 53: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 54: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 55: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 56: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 57: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 58: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 59: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 60: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 61: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 62: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 63: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 64: 173506 0 0 0 0 0 0 0 PCI-MSI-edge hda_intel NMI: 482 89 25 13 277 24 11 10 Non-maskable interrupts LOC: 783857 194752 114133 70577 372438 179065 117179 162016 Local timer interrupts SPU: 0 0 0 0 0 0 0 0 Spurious interrupts PMI: 482 89 25 13 277 24 11 10 Performance monitoring interrupts IWI: 0 0 0 0 0 0 0 0 IRQ work interrupts RES: 131917 46750 7432 3291 150003 9576 3435 3067 Rescheduling interrupts CAL: 2759 6563 7150 6997 5387 7140 7269 6678 Function call interrupts TLB: 4396 2038 1336 492 5434 1896 1121 606 TLB shootdowns TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 0 0 0 0 Machine check exceptions MCP: 37 37 37 37 37 37 37 37 Machine check polls ERR: 0 MIS: 0 Last but not least, right after boot-up those lines are usually present in dmesg: [ 18.367094] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj. [ 18.458859] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj. I'm not sure if it's related or a symptom of a bigger problem so I'm posting it just in case. I don't really know what other information might be of relevance here. Don't hesitate to ask for more in the comments.

    Read the article

  • Update Grub on Squeeze - Kernel downgrade due VMware Server

    - by vodoo_boot
    Hi! I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

    Read the article

  • How to Enable IPtables TRACE Target on Debian Squeeze (6)

    - by bernie
    I am trying to use the TRACE target of IPtables but I can't seem to get any trace information logged. I want to use what is described here: Debugger for Iptables. From the iptables man for TRACE: This target marks packes so that the kernel will log every rule which match the packets as those traverse the tables, chains, rules. (The ipt_LOG or ip6t_LOG module is required for the logging.) The packets are logged with the string prefix: "TRACE: tablename:chain- name:type:rulenum " where type can be "rule" for plain rule, "return" for implicit rule at the end of a user defined chain and "policy" for the policy of the built in chains. It can only be used in the raw table. I use the following rule: iptables -A PREROUTING -t raw -p tcp -j TRACE but nothing is appended either in /var/log/syslog or /var/log/kern.log! Is there another step missing? Am I looking in the wrong place? edit Even though I can't find log entries, the TRACE target seems to be set up correctly since the packet counters get incremented: # iptables -L -v -t raw Chain PREROUTING (policy ACCEPT 193 packets, 63701 bytes) pkts bytes target prot opt in out source destination 193 63701 TRACE tcp -- any any anywhere anywhere Chain OUTPUT (policy ACCEPT 178 packets, 65277 bytes) pkts bytes target prot opt in out source destination edit 2 The rule iptables -A PREROUTING -t raw -p tcp -j LOG does print packet information to /var/log/syslog... Why doesn't TRACE work?

    Read the article

  • Howto Nginx + git-http-backend + fcgiwrap (Debian Squeeze)

    - by brainsqueezer
    I am trying to setup git-http-backend with Nginx but after 24 hours wasting time and reading everything I could I think this config should work but doesn't. server { listen 80; server_name mydevserver; access_log /var/log/nginx/dev.access.log; error_log /var/log/nginx/dev.error.log; location / { root /var/repos; } location ~ /git(/.*) { gzip off; root /usr/lib/git-core; fastcgi_pass unix:/var/run/fcgiwrap.socket; include /etc/nginx/fastcgi_params2; fastcgi_param SCRIPT_FILENAME /usr/lib/git-core/git-http-backend; fastcgi_param DOCUMENT_ROOT /usr/lib/git-core/; fastcgi_param SCRIPT_NAME git-http-backend; fastcgi_param GIT_HTTP_EXPORT_ALL ""; fastcgi_param GIT_PROJECT_ROOT /var/repos; fastcgi_param PATH_INFO $1; #fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; } } Content of /etc/nginx/fastcgi_params2 fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param REMOTE_USER $remote_user; # required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; but config seems not working $ git clone http://mydevserver/git/myprojectname/ Cloning into myprojectname... warning: remote HEAD refers to nonexistent ref, unable to checkout. and I can request an unexistant project and I will get the same answer $ git clone http://mydevserver/git/thisprojectdoesntexist/ Cloning into thisprojectdoesntexist... warning: remote HEAD refers to nonexistent ref, unable to checkout. If I change root to /usr/lib I will get a 403 error and this will be reported to nginx error log: 2011/11/23 15:52:46 [error] 5224#0: *55 FastCGI sent in stderr: "Cannot get script name, is DOCUMENT_ROOT and SCRIPT_NAME set and is the script executable?" while reading response header from upstream, client: 198.168.0.4, server: mydevserver, request: "GET /git/myprojectname/info/refs HTTP/1.1", upstream: "fastcgi://unix:/var/run/fcgiwrap.socket:", host: "mydevserver" My main trouble is with the correct root value with this configuration. Maybe there are some permissions problems. Notes: /var/repos/ is owned by www-data and contains folders bit git bare repos. All this works perfectly using ssh. If I go with my browser to http://mydevserver/git/myproject/info/refs it is answered by git-http-backend asking me to send a command. /var/run/fcgiwrap.socket has 777 permissions.

    Read the article

  • ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

    - by frank
    Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

    Read the article

  • apache/debian squeeze server loading directory listing instead of website

    - by Diego
    when you navigate to mywebsite.com/ you see an apache page showing a folder called mywebsite.com/, clicking there then takes me to mywebsite.com/mywebiste.com which doesn't exist, so wordpress shows me the a 404 error. I'm trying to host a wordpress site at mywebsite.com/ but I think I have some kind of directory listing wrong somewhere, though I'm pretty sure I've set up my /etc/apache2/sites-available/mywebsite.com correctly: <VirtualHost *:80> ServerName mywebsite.com ServerAdmin [email protected] DocumentRoot /var/www/mywebsite.com/ <Directory /> Options FollowSymLinks AllowOverride All </Directory> ErrorLog /var/log/apache2/error.log CustomLog /var/log/apache2/access.log combined LogLevel warn </VirtualHost>

    Read the article

  • xen + debian network after upgrade squeeze to wheeze

    - by rush
    I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

    Read the article

  • Debian Squeeze can't install php-pear

    - by Lennier
    I use Debian 6.0.6 sudo apt-get install php-pear results in: Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: initscripts : Breaks: console-setup (< 1.74) but 1.68+squeeze2 is to be installed Breaks: initramfs-tools (< 0.104) but 0.98.8 is to be installed Breaks: nfs-common (< 1:1.2.5-3) but 1:1.2.2-4squeeze2 is to be installed keyboard-configuration : Breaks: console-setup (< 1.71) but 1.68+squeeze2 is to be installed klibc-utils : Breaks: initramfs-tools (< 0.103) but 0.98.8 is to be installed E: Broken packages How can i solve it?

    Read the article

  • SSH agent forwarding on debian squeeze

    - by nfvindaloo
    Im trying to set up SSH forwarding like this osx debianA debianB I can connect to debianA fine, using ssh -A and it has the following env vars when i do: SSH_AGENT_PID=1543 SSH_AUTH_SOCK=/tmp/ssh-giwdYY1542/agent.1542 SSH_CLIENT='92.233.199.x 38954 22' SSH_CONNECTION='92.233.199.x 38954 108.171.179.x 22' SSH_TTY=/dev/pts/0 When i try to connect to debianB, the agent is not used! ssh -v output ends with: debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /home/nic/.ssh/id_rsa debug1: Trying private key: /home/nic/.ssh/id_dsa debug1: Next authentication method: password Then im asked for a password. I have not set any ForwardAgent no directives in ssh_config and dont have a .ssh/config at all. sshd_config has not got AllowAgentForwarding in it. I have tried all of these directives as yes also. debianA and debianB both have identical ssh_config and sshd_config (verified with diff) so the really weird thing is connecting OSX debianB debianA works fine!! Im totally out of ideas! Has anyone come across this before? Cheers! NFV

    Read the article

  • Update Grub on Squeeze - Kernel downgrade due VMware Server

    - by vodoo_boot
    I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

    Read the article

  • Set source address to use tun device does not work (Debian Squeeze)

    - by A. Donda
    there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

    Read the article

  • Debian Squeeze - Monitor outgoing traffic

    - by Sam W.
    I have a small webserver that running on Lighttpd 1.4 which steadily uses 250GB or less bandwidth for the past couple of months. But since May the traffic spikeed to more than triple of what it was. Nothing special was on my site to make its spike like that. When I checked with vnstat I found that 70% of the bandwidth is tx. I suspect I've been hacked and my webserver is becoming some sort of bot. ClamAV comes out with nothing and I already replaced the Joomla installation with a fresh one, early in June. But right now the traffic stayed the same. My question, how can I monitor my server and look what is transmitting all that data out? My need to be done to pinpoint what is the culprit. Can someone please point to the right way to solve this? Thank you.

    Read the article

  • let CRON send emails through SMTP ( debian squeeze )

    - by supernova
    i would like to send emails whenever a cronjob has completed, i read that this is possible with exim4. in /etc/alias i added the line myuser: [email protected] in /etc/exim4/update-exim4.conf.conf i set dc_smarthost='smtp.myserver.ip::25 and in /etc/exim4/passwd.client i set smtp.myserver.ip:[email protected]:mypassword my problem is that i can't see any login at my mailserver, and in the exim logs i saw a few lines with 2012-10-13 09:17:01 1TMvy1-0001fp-F2 ** [email protected] R=nonlocal: Mailing to remote domains not supported 2012-10-13 09:17:01 1TMvy1-0001fr-JE <= <> R=1TMvy1-0001fp-F2 U=Debian-exim P=local S=17426 are there any additional config settings i have to set? edit : i solved the prev. error by running dpkg-reconfigure, but now i'm facing the following error <root@debian> R=dnslookup T=remote_smtp defer (-53): retry time not reached for any host

    Read the article

  • Debian - error while loading shared libraries

    - by Jirí Valoušek
    i have an problem with script DocToText from Silvercoders.com on my 64bit Debian Squeeze. It works properly on another 32bit machine, but on this i have still problem with some .so module. # file /bin/bash /bin/bash: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked (uses shared libs), for GNU/Linux 2.6.18, stripped if i run doctotext.sh it`s return an error: ./doctotext: error while loading shared libraries: libgsf-1.so.114: cannot open shared object file: No such file or directory please, can you help?

    Read the article

  • postfix check warm me that some file differ

    - by Nicolas BADIA
    If I run postfix check on my debian squeeze server, I get this: postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_nisplus-2.11.3.so and /lib/libnss_nisplus-2.11.3.so differ postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_files-2.11.3.so and /lib/libnss_files-2.11.3.so differ postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_compat-2.11.3.so and /lib/libnss_compat-2.11.3.so differ postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_hesiod-2.11.3.so and /lib/libnss_hesiod-2.11.3.so differ postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_nis-2.11.3.so and /lib/libnss_nis-2.11.3.so differ postfix/postfix-script: warning: /var/spool/postfix/lib/libnss_dns-2.11.3.so and /lib/libnss_dns-2.11.3.so differ Somebody know a solution to fix this ?

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >