Search Results

Search found 138 results on 6 pages for 'stripe'.

Page 3/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

• MegaCli newly created disk doesn't appear under /dev/sdX

  - by Henry-Nicolas Tourneur

  After having successfully added 2 new disks in a new RAID virtual drive (background initialization done), I would have exepected it to appear under /dev/sdh but it's not there (so, unusable). The system is running a CentOS 5.2 64 bits, HAL and udev daemons are running, not records of any sdh apparition under the messsage log file or in dmesg, only MegaCli do see that virtual drive. Any idea ? Some data: [root@server ~]# ./MegaCli -LDInfo -LALL -a0 Adapter 0 -- Virtual Drive Information: Virtual Disk: 0 (target id: 0) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:139392MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Virtual Disk: 1 (target id: 1) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:285568MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default [root@server ~]# ls -l /dev/disk/by-id/scsi-360* lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09 -> ../../sda lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part1 -> ../../sda1 lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part2 -> ../../sda2 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee -> ../../sdf lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee-part1 -> ../../sdf1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f -> ../../sdb lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec -> ../../sde lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec-part1 -> ../../sde1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d -> ../../sdd lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7 -> ../../sdc lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7-part1 -> ../../sdc1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1 -> ../../sdg lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1-part1 -> ../../sdg1

  Read the article

• Day 4 - Game Sprites In Action

  - by dapostolov

  Yesterday I drew an image on the screen. Most exciting, but ... I spent more time blogging about it then actual coding. So this next little while I'm going to streamline my game and research and simply post key notes. Quick notes on the last session: The most important thing I wanted to point out were the following methods:           spriteBatch.Begin(SpriteBlendMode.AlphaBlend);           spriteBatch.Draw(sprite, position, Color.White);           spriteBatch.End(); The spriteBatch object is used to draw Textures and a 2D texture is called a Sprite A texture is generally an image, which is called an Asset in XNA The Draw Method in the Game1.cs is looped (until exit) and utilises the spriteBatch object to draw a Scene To begin drawing a Scene you call the Begin Method. To end a Scene you call the End Method. And to place an image on the Scene you call the Draw method. The most simple implementation of the draw method is:           spriteBatch.Draw(sprite, position, Color.White); 1) sprite - the 2D texture you loaded to draw 2) position - the 2d vector, a set of x & y coordinates 3) Color.White - the tint to apply to the texture, in this case, white light = nothing, nada, no tint. Game Sprites In Action! Today, I played around with Draw methods to get comfortable with their "quirks". The following is an example of the above draw method, but with more parameters available for us to use. Let's investigate!             spriteBatch.Draw(sprite, position2, null, Color.White, MathHelper.ToRadians(45.0f), new Vector2(sprite.Width / 2, sprite.Height / 2), 1.0F, SpriteEffects.None, 0.0F); The parameters (in order): 1) sprite  the texture to display 2) position2 the position on the screen / scene this can also be a rectangle 3) null the portion of the image to display within an image null = display full image this is generally used for animation strips / grids (more on this below) 4) Color.White Texture tinting White = no tint 5) MathHelper.ToRadians(45.0f) rotation of the object, in this case 45 degrees rotates from the set plotting point. 6) new Vector(0,0) the plotting point in this case the top left corner the image will rotate from the top left of the texture in the code above, the point is set to the middle of the image. 7) 1.0f Image scaling (1x) 8) SpriteEffects.None you can flip the image horizontally or vertically 9) 0.0f The z index of the image. 0 = closer, 1 behind? And playing around with different combinations I was able to come up with the following whacky display:   Checking off Yesterdays Intention List: learn game development terminology (in progress) - We learned sprite, scene, texture, and asset. how to place and position (rotate) a static image on the screen (completed) - The thing to note was, it's was in radians and I found a cool helper method to convert degrees into radians. Also, the image rotates from it's specified point. how to layer static images on the screen (completed) - I couldn't seem to get the zIndex working, but one things for sure, the order you draw the image in also determines how it is rendered on the screen. understand image scaling (in progress) - I'm not sure I have this fully covered, but for the most part plug a number in the scaling field and the image grows / shrinks accordingly. can we reuse images? (completed) - yes, I loaded one image and plotted the bugger all over the screen. understand how framerate is handled in XNA (in progress) - I hacked together some code to display the framerate each second. A framerate of 60 appears to be the standard. Interesting to note, the GameTime object does provide you with some cool timing capabilities, such as...is the game running slow? Need to investigate this down the road. how to display text , basic shapes, and colors on the screen (in progress) - i got text rendered on the screen, and i understand containing rectangles. However, I didn't display "shapes" & "colors" how to interact with an image (collision of user input?) (todo) how to animate an image and understand basic animation techniques (in progress) - I was able to create a stripe animation of numbers ranging from 1 - 4, each block was 40 x 40 pixles for a total stripe size of 160 x 40. Using the portion (source Rectangle) parameter, i limited this display to each section at varying intervals. It was interesting to note my first implementation animated at rocket speed. I then tried to create a smoother animation by limiting the redraw capacity, which seemed to work. I guess a little more research will have to be put into this for animating characters / scenes. how to detect colliding images or screen edges (todo) - but the rectangle object can detect collisions I believe. how to manipulate the image, lets say colors, stretching (in progress) - I haven't figured out how to modify a specific color to be another color, but the tinting parameter definately could be used. As for stretching, use the rectangle object as the positioning and the image will stretch to fit! how to focus on a segment of an image...like only displaying a frame on a film reel (completed) - as per basic animation techniques what's the best way to manage images (compression, storage, location, prevent artwork theft, etc.) (todo) Tomorrows Intention Tomorrow I am going to take a stab at rendering a game menu and from there I'm going to investigate how I can improve upon the code and techniques. Intention List: Render a menu, fancy or not Show the mouse cursor Hook up click event A basic animation of somesort Investigate image / menu techniques D.

  Read the article

• Blurry vertical sections using fglrx with Radeon hd 6970

  - by Jesus Ramos

  So I managed to get fglrx working by downloading the drivers from ATI because the ones from additional drivers boot to a black screen and the open source dont let me change resolution. My one issue is that half of my monitor is fine and the other half is blurry almost as if there's a blurry vertical stripe on the right side. I tried disabling Compiz and have the same issue in both gnome and kde, I was wondering if theres an xorg.conf change that could be made to fix this as I have already set the resolution and refresh rates to the correct values.

  Read the article

• how to create texture for modelmesh?

  - by Berend

  Is there a possibiltiy to create a texture from a meshpart in xna. By getting a flat version of the mesh. So I can create a texture for it and edit that texture(via rendertarget)? I need to get the texture(wich is not yet a texture) so I can put another texture on it. I can create a texture and put it on a certain mesh. But I just cant figure out how I can create a texture with the right size. I also already found out i can use text2dproj in hlsl. But when i do this i get a gray stripe in the look. Is there a better solution?

  Read the article

• Fusion Learning Center News

  - by Richard Lefebvre

  The Fusion Learning Center portal now includes more than 1,600 learning assets. With so many assets, we have re-organized this portal slightly by introducing a new References section in the right lower corner, where we are providing quick links to the key assets. Furthermore, we have introduced a new Release Readiness section in the left navigation. Currently this points to the latest release; Release 4. We will be updating this section to also include the ability to stripe the assets by release. More to come on this later! New Assets and Uplifted Content include: The CRM Family Foundation webinar is updated to reflect the latest content CRM has also created two new Sales Positioning webinars: Contracts Solution Pitch and PRM Solution Pitch The Fusion Apps FAQ is updated - the changes can be found in the change log

  Read the article

• How to shade a texture two different colors?

  - by Venesectrix

  To give an example of what I'm asking about, I'll use Saints Row 3 since I've been playing that lately. In that game you can customize your looks and your car's appearance a lot. Your coat can have a primary color and a trim color. Your car can have a primary color and a stripe color, etc. Is there just a single coat texture that is being shaded two different colors somehow or are they overlaying a transparent second texture for the trim/stripes that gets shaded differently? If it's just one texture I'd like to know how it's done. If it's two different textures it seems like it's a waste of space. The second texture would be the same size as the first one but mostly transparent if you just wanted to lay it on top of the first one. Or are they just carefully positioning a second, smaller texture so that it aligns properly with the first one?

  Read the article

• What payment processors fullfill this requirements and what are their pluses and minuses? [on hold]

  - by Sharen Eayrs

  Accept credit card Allow me to automatically credit a customers' account. We're not selling e-book. We're selling a credit to our account. So it's important that customers do not get credited twice. Easy to program and integrate with our sites. Have affiliate programs. Transfer money to bank accounts quickly Accept merchants from many countries No monthly fee is a plus. I am thinking of using 2co.com avangate.com clickbank.com Some people reccomend https://stripe.com/us/features (is it easy to implement) http://www.paymentwall.com/ There are so many payment processor I am very confused. Can anyone tell me pluses and minuses of those ones. or perhaps others. What would be the plus and minuses of those 3 that you know off

  Read the article

• Black screen on Ubuntu 12.04

  - by user1648371

  I've just upgraded to Ubuntu 12.04 and I'm experiencing some problems. The first thing I noticed is that when I click the Workspace switcher all I get is a black screen (I can guess where the different workspaces are located and clicked on them, not a practical solution though). In addition when I lock the screen or suspend the laptop (a Vaio VPCEB4M1E) I get a shifted screen (I see the right most vertical stripe on the left size of the monitor and nothing about all the rest, to put it clearly I can see the gear that allows me to turn the pc off, etc, but not much more..) when I go to the additional driver menu I see the "ATI/AMD proprietary FGLRX graphics driver" are installed and the post-release update version is available. I don't know if the problem is driver related, so before doing anything I'd like to get some suggestions from you guys. Thanks you!

  Read the article

• Application Interface between a PC and an embedded device

  - by sasayins

  Hi, How can I make an application interface so that a PC application can communicate to an embedded device like a POS terminal? Like for example, an embedded device like POS terminal that has an embedded linux as an OS. Then I want a PC application to communicate in that POS terminal and access its module hardware like for example its magnetic stripe reader. What implementation should I create in the device, should I use CORBA or something related in that technology so that a PC application can communicate in the POS terminal? Many thanks.

  Read the article

• Body background fluke - white space on top

  - by gnomixa

  This is really weird. When this page is viewed in FF, it gets a white stripe on top which is part of body - I know because I use red border technique to see the elements. Any ideas why? http://www.codecookery.com/allbestimages/index.php?main_page=home

  Read the article

• How to create zebra stripes on html table without using javascript and even/odd classes generation?

  - by Vladimir

  I want to zebra-stripe a html table without using any js stuff or writing server-side code to generate even/odd classes for table rows. Is it ever possible to do using raw css?

  Read the article

• VS 2010 problem?

  - by Tony J

  For a short time now I have had a problem or pain with the Breakpoint indicators, they do not show, yes I have the margin activated ( small grey stripe down the left side of the margin ). I have uninstalled all extensions, addins etc still no breakpoint indicator I have also deleted the .suo file with no go also. This is a major pain more than anything else. Anyone who has had this problem please help me out.

  Read the article

• Class definition thinks setting a variable is a Unit?

  - by DeLongey

  Writing out a Scala class and problem here is that the compiler thinks that the code is a unit not returning the proper value. It's a method used to set a property in the class: def setObject(`object`:StripeObject):StripeObject = { this.`object` = `object` } The error is: type mismatch; found : Unit required: com.stripe.StripeObject The full class is: case class EventData(var previousAttributes: HashMap[String,Object], var `object`:StripeObject) extends StripeObject { def getPreviousAttributes = { previousAttributes } def setPreviousAttributes(previousAttributes: HashMap[String, Object]) = { this.previousAttributes = previousAttributes } def getObject = { `object` } def setObject(`object`:StripeObject):StripeObject = { this.`object` = `object` } } How do I make sure it doesn't return a Unit?

  Read the article

• Android - Skewed button

  - by teepusink

  Hi, is it possible to create a skewed shape button? (i.e like a stripe shape from bottom left of screen to top right of screen)? Thanks, Tee

  Read the article

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Windows 7 Disk Management Spanned Volume vs Striped Volume

  - by Kairan

  Im looking for a reason why a person would use a Spanned volume rather than a Striped volume? If my understanding is correct Striped: Faster read/write speed than spanned, but I "assume" more wear+tear Spanned: No speed benefit like striped, but data is written sequentially and fills up Drive1 before filling up Drive2, so it saves on wear+tear Beyond that Im not sure if there is any other deciding factor on which to use. Definition found below: A striped volume uses the free space on more than one physical hard disk to create a bigger volume. Unlike a spanned volume, a striped volume writes across all volumes in the stripe in small blocks, distributing the load across the disks in the volume. The portions of disk used to create the volume need to be the same size; the size of the smallest free space included in the striped volume will determine.

  Read the article

• Black screen on Ubuntu 12.04

  - by user1648371

  I've just upgraded to Ubuntu 12.04 and I'm experiencing some problems. The first thing I noticed is that when I click the Workspace switcher all I get is a black screen (I can guess where the different workspaces are located and clicked on them, not a practical solution though). In addition when I lock the screen or suspend the laptop (a Vaio VPCEB4M1E) I get a shifted screen (I see the right most vertical stripe on the left size of the monitor and nothing about all the rest, to put it clearly I can see the gear that allows me to turn the pc off, etc, but not much more..) when I go to the additional driver menu I see the "ATI/AMD proprietary FGLRX graphics driver" are installed and the post-release update version is available. I don't know if the problem is driver related, so before doing anything I'd like to get some suggestions from you guys. Thanks you!

  Read the article

• How do i use storage spaces?

  - by Lucas

  I am planning on building a new windows 2012 server for a client and I have no experience in doing so. I have built many linux servers for them and setting up software raid during the install is a trivial matter. I have been unable to confirm that the windows 2012 install process has an analogous process for setting up Storage Spaces during the install. Can Storage Spaces be used as an installation target (configured during setup?) Is it capable of mirror+stripe (RAID10)? We have not ordered the hardware yet, so I'm looking for clarification.

  Read the article

• partition alignment on fresh windows 2003 ent server

  - by Datapimp23

  Hi, I have this server which has it's physical disks in RAID 5 controlled by a 3com raid controller. size of the stripe unit is unknown for the moment (Can check tomorrow in the office). I need to install windows server 2003 ENT and create 2 partitions (OS, Data). I'd like to create the partitions before the installation on windows server. They have to be aligned properly. I have the newest version of gparted on a disc but I have no clue if this is the right tool. Can someone point me in the right direction? Thanks

  Read the article

• GlusterFs - high load 90-107% CPU

  - by Sara

  I try and try and try to performance and fix problem with gluster, i try all. I served on gluster webpages, php files, images etc. I have problem after update from 3.3.0 to 3.3.1. I try 3.4 when i think maybe fix it but still the same problem. I temporarily have 1 brick, but before upgrade will be fine. Config: Volume Name: ... Type: Replicate Volume ID: ... Status: Started Number of Bricks: 0 x 2 = 1 Transport-type: tcp Bricks: Brick1: ...:/... Options Reconfigured: cluster.stripe-block-size: 128KB performance.cache-max-file-size: 100MB performance.flush-behind: on performance.io-thread-count: 16 performance.cache-size: 256MB auth.allow: ... performance.cache-refresh-timeout: 5 performance.write-behind-window-size: 1024MB I use fuse, hmm "Maybe the high load is due to the unavailable brick" i think about it, but i cant find information on how to safely change type of volume. Maybe u know how?

  Read the article

• HP DL180 G6 P410 8x SATA 1TB, what is the optimal configuration?

  - by Oneiroi

  I have a HP DL180 G6 with a P410 raid controller. Presently this runs using 4x 1TB Samsung Spinpoint SATA drives, in a RAID10 configuration using default settings. I am about to add a backplane to increase the drive capacity from 4 to 12 drives, and I plan to install 4 more 1TB SATA Drives. The drives are matched and have close serial numbers (They arrived together in the Manufacturers pallet). Model HD103UJ 1000GB/7200rpm/32M Rated for 3GB/s I will also be installing RHEL 6.1 x86_64. My question is what would be the optimal RAID settings (stripe etc.) for this configuration? To recap: 8x Model HD103UJ 1000GB/7200rpm/32M Rated for 3GB/s RAID 10 configuration. Thanks in advance. Update for role: Server is to become an iscsi target for an internal openstack deployment currently underway. (Glance) Will also provide virtualisation through KVM

  Read the article

• Horrible performing RAID

  - by Philip

  I have a small GlusterFS Cluster with two storage servers providing a replicated volume. Each server has 2 SAS disks for the OS and logs and 22 SATA disks for the actual data striped together as a RAID10 using MegaRAID SAS 9280-4i4e with this configuration: http://pastebin.com/2xj4401J Connected to this cluster are a few other servers with the native client running nginx to serve files stored on it in the order of 3-10MB. Right now a storage server has a outgoing bandwith of 300Mbit/s and the busy rate of the raid array is at 30-40%. There are also strange side-effects: Sometimes the io-latency skyrockets and there is no access possible on the raid for 10 seconds. The file system used is xfs and it has been tuned to match the raid stripe size. Does anyone have an idea what could be the reason for such a bad performing array? 22 Disks in a RAID10 should deliver way more throughput.

  Read the article

• RAID0 array of USB 2 disks, both connected to a single hub. Any benefit?

  - by Josh

  I have two unused USB 2 drives. I wanted to stripe them in a RAID0 configuration for fast disk access for virtual machines. (I find running a VMware virtual machine off a USB2 drive to be painfully slow. Especially Windows Vista) If I have both USB drives attached to the same USB2 hub, will that negate any benefit I gain by creating a RAID0 array? That is to say, is the speed of USB2 the limiting factor or is the speed of the drives? Would I get better performance by attaching one or both drives directly to my computer?

  Read the article

• Why can't add a hot spare in freebsd? Can anybody help me fix it?

  - by hamlet

  Why can't add a hot spare? Can anybody help me fix it? mfiutil add e1:s1 mfid0 mfiutil: Drive 1 is not available My mfi status:: mfiutil show config mfi0 Configuration: 1 arrays, 1 volumes, 0 spares array 0 of 2 drives: drive 0 ( 137G) ONLINE <HITACHI HUS153014VLS300 A410 serial=JFWHSB4C> SAS enclosure 1, slot 0 drive 1 ( 137G) ONLINE <HITACHI HUS153014VLS300 A410 serial=JFWJ3AEC> SAS enclosure 1, slot 1 volume mfid0 (136G) RAID-1 64K OPTIMAL spans: array 0 mfiutil show events 1468 (boot + 25s/BATTERY/WARN) - Battery removed 1475 (boot + 52s/DRIVE/WARN) - PD 00(e1/s0) is not a certified drive 1478 (boot + 52s/DRIVE/WARN) - PD 01(e1/s1) is not a certified drive 1480 (boot + 64s/BATTERY/WARN) - BBU disabled; changing WB virtual disks to WT mfiutil show volumes mfi0 Volumes: Id Size Level Stripe State Cache Name mfid0 ( 136G) RAID-1 64K OPTIMAL Disabled

  Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >