Search Results

Search found 2799 results on 112 pages for 'hp ux'.

Page 30/112 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

  • hp dl580 g5 diag error

    - by maruti
    server disk access is slow, and running insight diagnostics reports this error: Error: 640003 DST Error Error: 640006: The Read and/or Write HARD error rate is above threshold This drive has experienced/recorded error conditions reported by diagnosis and requires replacement"

    Read the article

  • Base system driver error - HP Pavilion Entertainment PC dv9323cl

    - by Damurph
    I upgraded to Wndows 7 and have a problem with graphics with my NVIDIA GeoForce Go 7600 not displaying properly. Also the Base System Drivers have yellow flags near them and it states that the The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver. Any clues??? Please help!

    Read the article

  • HP ProCurve GVRP Setup

    - by Matt
    I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother and GVRP is pushing its configurations from the 3500 to the 3 other switches. My question is, once GVRP is setup, how exactly do I configure the ports on the 3 L2 switches to use the correct VLAN? I'm new to ProCurve network equipment and this is much easier to setup on Cisco equipment.

    Read the article

  • Linksys SRW248g4p and hp procurves

    - by Garfield81
    We've got about 3 procurves linked up with about 5 linksys srw248g4p. Pinging between the Procurves I get ping time between 1-2 ms and pinging between the linksys the ping time are averaging 40 ms. I have evening tried pinging between two linksys switches that are connected to each other directly using the GB ports. There have no modification done to the switches and the firmware seems to be uptodate. Any suggestions would be appreciated.

    Read the article

  • Setup of HP ProCurve 2810-24G for iSCSI?

    - by 3molo
    Hi, I have a pair of ProCurve 2810-24G that I will use with a Dell Equallogic SAN and Vmware ESXi. Since ESXi does MPIO, I am a little uncertain on the configuration for links between the switches. Is a trunk the right way to go between the switches? I know that the ports for the SAN and the ESXi hosts should be untagged, so does that mean that I want tagged VLAN on the trunk ports? This is more or less the configuration: trunk 1-4 Trk1 Trunk snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 24,Trk1 ip address 10.180.3.1 255.255.255.0 no untagged 5-23 exit vlan 801 name "Storage" untagged 5-23 tagged Trk1 jumbo exit no fault-finder broadcast-storm stack commander "sanstack" spanning-tree spanning-tree Trk1 priority 4 spanning-tree force-version RSTP-operation The Equallogic PS4000 SAN has two controllers, with two network interfaces each. Dell recommends each controller to be connected to each of the switches. From vmware documentation, it seems creating one vmkernel per pNIC is recommended. With MPIO, this could allow for more than 1 Gbps throughput.

    Read the article

  • Setup VLAN agnostic ports on HP ProCurve 1810G (Ingress Filter, Trunking)

    - by Thomas
    I am wondering if it is possible to configure some ports of the web managed ProCurve Switch 1810G to participate in all VLAN traffic. Even if no VLAN with that ID has been set up inside the switch. The issue is that I have two virtualization servers that will use yet unknown VLANs of a certain range to communicate with each other. But the range is much larger than the 64 supported VLANs this switch can manage. The switch also offers static and LACP Link Trunks. But I guess there will also apply the Ingress Filter that drops packets with unconfigured VLAN IDs? A separate unmanaged switch that connects the two hosts and one ProCurve Port would work, but maybe I do not have to? Thanks

    Read the article

  • How to speed up a HP M9517C

    - by Jen
    I bought a system with 8GB RAM, 1TB HD, Quad-Core AMD Phenom 9550, Nvidia Geforce 9300GE, 64-bit Windows Vista Machine. Bought it primarily because it was cheap and came with 25.5 inch screen. Problem: It's slow - if you can believe it. My Dell laptop 1525 is faster and more stable! I tried installing and dual-booting Linux Mint and ran into video and audio troubles. I need fast and stable and I'm going for awesome. Anyone have some suggestions on making this thing smoking hot? Vista is fine, but slows over time - suspect virus/spyware/etc.. But I need to use Photoshop, Fireworks, Dreamweaver, Illustrator. I've tried the alternatives and I just don't like them. When you've got deadlines looming you want to work with what you know. Also use Skype (and I had audio problems with it in Linux), gotomeeting, gotowebinar. Don't need MS Office. Tried VMWare, Virtualbox and again - I keep getting audio/video problems. I'd love someone's input on THEIR setup and how they got there. I'm sure I need to upgrade my video card, but what should I go to?

    Read the article

  • Sendmail configs and logs look correct, but I get no mail

    - by Christian Dechery
    I used this tutorial to config sendmail on Ubuntu. Followed every step and when I test it, it seems to have worked, but I get no mail (not even on the spam folder) Below is the log for a test message: 050 >>> MAIL From:<[email protected]> SIZE=345 AUTH=<> 050 250 2.1.0 OK ek1sm23505399vdc.28 - gsmtp 050 >>> RCPT To:<######@gmail.com> 050 250 2.1.5 OK ek1sm23505399vdc.28 - gsmtp 050 >>> DATA 050 354 Go ahead ek1sm23505399vdc.28 - gsmtp 050 >>> . 050 250 2.0.0 OK 1401150762 ek1sm23505399vdc.28 - gsmtp 050 <########@gmail.com>... Sent (OK 1401150762 ek1sm23505399vdc.28 - gsmtp) 250 2.0.0 s4R0WdYN007263 Message accepted for delivery ######@gmail.com... Sent (s4R0WdYN007263 Message accepted for delivery) And this is my /var/log/mail.log May 26 21:32:39 UX-BLUEROOM sendmail[7262]: s4R0Wdxq007262: from=christian, size=105, class=0, nrcpts=1, msgid=<[email protected]>, relay=christian@localhost May 26 21:32:40 UX-BLUEROOM sm-mta[7263]: s4R0WdYN007263: from=<[email protected]>, size=345, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] May 26 21:32:41 UX-BLUEROOM sm-mta[7263]: STARTTLS=client, relay=gmail-smtp-msa.l.google.com., version=TLSv1/SSLv3, verify=FAIL, cipher=ECDHE-RSA-RC4-SHA, bits=128/128 May 26 21:32:42 UX-BLUEROOM sm-mta[7263]: s4R0WdYN007263: to=<######@gmail.com>, ctladdr=<[email protected]> (1000/1000), delay=00:00:02, xdelay=00:00:02, mailer=relay, pri=30345, relay=gmail-smtp-msa.l.google.com. [173.194.75.109], dsn=2.0.0, stat=Sent (OK 1401150762 ek1sm23505399vdc.28 - gsmtp) May 26 21:32:42 UX-BLUEROOM sendmail[7262]: s4R0Wdxq007262: to=#####@gmail.com, ctladdr=christian (1000/1000), delay=00:00:03, xdelay=00:00:03, mailer=relay, pri=30105, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (s4R0WdYN007263 Message accepted for delivery)

    Read the article

  • RAID Array performance on an HP Proliant ML350 G5 Smart Array E200i

    - by Nate Pinchot
    We have a client who is complaining about performance of an application which utilizes an MS SQL database. They do not believe the performance issues are the fault of the application itself. The Smart Array E200i RAID controller has 128MB cache and we have the cache set to 75% read/25% write. The disk array set to enable write caching. Recently we ran a disk performance test using SQLIO based on this guide. We used a 10 GB file for the test found that the average sequential read rate was ~60 MB/sec (megabytes/sec) and the average random read rate was ~30 MB/sec. Are these numbers on par for what the server should be performing? Better than on par? Horrible? Amazing?

    Read the article

  • VPN to Buffalo WHR-HP-G300N produces a Connection Error 807

    - by Darius
    My friend has modem/router from Clear and I have sent him Buffalo router to put it between his Clear device and the Network. I walked him thru establishing VPN in DD-WRT but when I try to VPN I get a VPN Connection Error 807. I am out of ideas how to solve this. Any suggestion? Clear Modem WAN: xx.xx.xx.xx Clearn Modem NAT's to: 192.168.15.XXX Clear Modem DHCP: 192.168.15.2 - 192.168.15.2 (range is limited to that of ONE ip address) Clear Modem DMZ: 192.168.15.2 the LAN of the clear modem is 192.168.15.XXX The DD-WRT IP: 192.168.4.1 Port FWD: 1723 to 192.168.4.1 PPTP server listens on 192.168.4.1 Where is the problem with this setup?

    Read the article

  • HP DL 380G7 Raid swap drives

    - by dean
    disks 0 and 1 are raid redundant (OS) and the remaining 6 drives are in raid 5 I believe. i would like to pull out disks 0 and 1 and install new drives to build a new OS. I need to be able to reinsert the old drives and reboot back to the original OS. (swap) I had a serious problem in the past attempting this. does the raid require (look for) the drives based on a serial number or something? just dont want to lose data. thanks

    Read the article

  • OS X printing to HP Photosmart black only

    - by churnd
    When you print something to a Photosmart printer in OS X, by default it prints color. If you want black and white, you have to manually change the settings. How do I fix it to where it prints black and white by default, and if you want color, you have to change the settings? More specifically, I want the default to be black and white that uses only the black cartridge.

    Read the article

  • No power to HP pavilion dv 1000

    - by Imajica666
    I am working on a friends laptop. I get no power indicator light while plugged in to ac outlet. Will not power on with just the battery. Might this be a case of replacing the system board? I have never broken open a laptop so I am not sure what the best path to take might be. Thanks for any opinions.

    Read the article

  • Configuring HP Proliant iLO using hponcfg

    - by Abhay Kumar
    I am configuring an iLO using hponcfg by logging into the machine remotely and running hponcfg with scripts Mod_Directory.xml and then with Mod_Network.xml. I am enabling the DHCP on the device. But after the above scripts are executed successfully and upon rebooting the iLO, it shows the IP address to be 0.0.0.0. What is missing here, so that the iLO gets an IP from DHCP automatically after configuration?

    Read the article

  • Enable Hardware Virtualization on HP CompaqDX2420?

    - by 7alwagy
    Hey Guys, After installing vmware7, I tried to run a virtual machine with Mac OSX installed. When I tried to run this virtual machine I got an error message saying: Mac OS X is not supported with software virtualization. To run Mac OS X you need a host on which VMware Workstation supports hardware virtualization. I'v googled and found out that my processor (Intel Core 2 Duo E7500 Processor (2.93 GHz, 3 MB L2 cache, 1066 Mhz FSB)supports Hardware virtualization. Does anyone know how to enable this in order to get this virtual machine running?

    Read the article

  • How do I get an HP 1018 laser printer to work on 12.04?

    - by MInner
    edit : already printed on windows-machine Ubuntu 12.04, LJ 1018. I've tried making foo2zjs from sourse. I've downloaded firmware and placed it where necessarily manually from here I've also tried this - same as manual dowload but with some patches like stoping cups, etc.. I've fixed usbfs: process 11200 (usb) did not claim interface 0 before use problems using sudo rmmod usblp as described here. And now I have Aug 10 11:51:59 pav /usr/sbin/hplj1018: foo2zjs: usb://HP/LaserJet%201018?serial=KP07RLV... download failed. Aug 10 11:51:59 pav /usr/sbin/hplj1018: foo2zjs: loading HP LaserJet 1018 firmware /lib/firmware/hp/sihp1018.dl to CUPS USB device ... error. Before that prinet was stucking on "Sending data to printer". Now it's code is "Not connected". Unless ben@pav:~$ lsusb ... Bus 001 Device 015: ID 03f0:4117 Hewlett-Packard LaserJet 1018 Thank you.

    Read the article

  • Monitoring Dell/HP Servers Running ESXi (Free)

    - by Untalented
    What are you all doing to monitor ESXi servers that run the free edition? With the lack of SNMP support, it seems fairly limited to me. What'd I'd like to be able to do is get some type of alert when a drive or other hardware fails. I've seen a few articles on getting OpenManage installed on an ESXi box (to rebuild an array), but it seems to be quite a pain as well. Even if I get OpenManage working, I won't have alerts without SNMP. Any comments, input, or guidance would be greatly appreciated.

    Read the article

  • HP va-t-il s'attaquer à Microsoft ? Le constructeur va se lancer dans le Cloud Computing où il pourrait concurrencer Windows Azure

    HP va-t-il s'attaquer à Microsoft ? Le constructeur va se lancer dans le Cloud Computing où il pourrait concurrencer Windows Azure Le PDG change, la stratégie aussi. Au temps de Mark Hurd, l'alliance entre le constructeur HP et le fournisseur d'OS Microsoft était claire. Les deux sociétés complétaient leurs offres respectives avec les atouts de l'autre. Le hardware de HP et la plateforme Azure de Microsoft formaient des appliances complètes, clef-en-main, à destination des Cloud privés et des data-centers des entreprises. C'est encore théoriquement le cas aujourd'hui. Mais depu...

    Read the article

  • Slow Starting DHCP Client Service - HP Thin Clients

    - by Ryan
    We have recently began adding XPe thin clients to our domain in preperation for a new citrix environment. One thing that has been picked up on in testing is that they appear slow to boot. The issue manifest's it's self as the classic "Applying Computer Settings..." screen we are all used to seeing. After digging into the issue it appears the DHCP Client service is taking some time to load on boot, this varies but I would estimate it can take around 1 minute in some cases. I've eliminated the classic issues, DHCP is responding correctly and in quick time. DNS is not the cause and GPO's are applying promptly. A simple workaround is to assign the client a static IP which work's great so the TCP/IP servies are obviously firing up quickly, just not DHCP Client. Does anyone have any idea's on how I may be able to improve the service start time? Keen to find a better solution before I get my arm twisted into setting up 250 thin clients with static addressing!

    Read the article

  • Difficulty racking HP ProLiant Gen8 servers

    - by Systemspoet
    We're an all Proliant shop with around 50 servers, mostly DL360s and DL380, from G5's through G7's. We just got our first two G8's in and went to rack them. We were stunned to find out that the new cable management arms protrude almost 1 inch deeper into the rack then previous iterations of the Proliant line. Unfortunately that causes them to occupy the same space as the PDU's in our APC racks. In a non-densely populated section of rack that's no biggie, but in a densely populated section it's impossible to get the cable arm into place without dislodging another machine's power. Has anyone else run into this? Obviously racking machines without cable management arms is not an option. I supposed we could reconfigure our racks but that's a nightmare.

    Read the article

  • ksh Auto-Completion PuTTY Configuration

    - by Nitrodist
    I'm having a bit of a problem configuring my PuTTY client to work with the auto-completion feature in the ksh shell. I do a listing on the root with the directories /home and /homeroot and it returns the directories in a list just fine. I can't select it, though, by hitting X = (where X is the number). /home/nitrodist>ls /h #hits esc + = 1) home/ 2) homeroot/ #hits 2 + = for the 'homeroot' dir 1) home/ 2) homeroot/ #hits just the '=' key. 1) home/ 2) homeroot/ Any ideas? I've su -'d to another user who can actually do it with their PuTTY session and I can't do it there, which makes me think it's a PuTTY configuration issue. This is running on a ksh93 shell on HP-UX, if that makes any difference. Here's my ksh config: /home/campbelm>set -o Current option settings allexport off bgnice on emacs off errexit off gmacs off ignoreeof off interactive on keyword off markdirs off monitor on noexec off noclobber off noglob off nolog off notify off nounset off privileged off restricted off trackall off verbose off vi on viraw on xtrace off /home/campbelm>

    Read the article

  • HP DV5T laptop problems using Adobe in multiple monitors

    - by Rolnik
    I have a dualview arrangement of two monitors that works just fine for 90% of my applications. However, any time I open Adobe Acrobat Reader to the larger monitor, it fails to permit enlarging of the window to fill the entire screen. In other words, it seems Adobe crops the PDF view at about the size of the smaller of the two monitors, despite Acrobat being present in the larger monitor. I'm using nVideo graphics on the laptop, and connecting to the larger monitor through the docking port of a docking station. Any ideas how to get the Acrobat to be aware that it has more screen real-estate and use it fully?

    Read the article

  • HP storageworks ultrium 448

    - by Graham
    Goodday, I have never cleaned the servers at my work but they are now running 5 times a week for 5 years. Now they asked me to clean it with the tape that has come with it. My qeustion is how do you clean it? Just put the tape in but then what? Hope someone gives me an answer.

    Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >