Search Results

Search found 3463 results on 139 pages for 'physical'.

Page 30/139 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• Linux SW Raid: whole disk or per-partition?

  - by Steve Pomeroy

  I have inherited a machine which has 2 physical disks and uses Linux SW RAID(1). Both disks are partitioned and are are all individual arrays (/dev/md0, /dev/md6, etc.). Those arrays are then mounted (/boot, /home, etc. even /tmp). As RAID is designed to mitigate physical failures, is there any reason why one would use this technique over whole-disk arrays that are then partitioned (perhaps using LVM)? This seems prone to more potential issues, but may have some special properties that I haven't been able to glean. I'm planning on moving this setup to: disks?SWRAID(1)?LVM as I'll be making multiple VMs out of the one machine, but wanted to make sure I knew what I was doing when I got rid of the old setup.

  Read the article

• USB Thumb Drive not recognized in Hyper-V Manager

  - by Vazgen

  I have the free, standalone core Hyper-V Server 2012 running on my physical machine. I set up remote management from my Windows 8 client. When I proceed to create a virtual machine I would like to install the OS from a usb thumb drive but it is not recognized in Hyper-V Manager on my client (when the USB is plugged into the physical server) nor is it recognized in Server Manager under File and Storage Services Volumes Is there a role needed to recognize external usb flash drives? Because I think this standalone version is just core Hyper-V role and that's it... but this is such a basic functionality. Can anybody comment.

  Read the article

• Quantifying the effects of partition mis-alignment

  - by Matt

  I'm experiencing some significant performance issues on an NFS server. I've been reading up a bit on partition alignment, and I think I have my partitions mis-aligned. I can't find anything that tells me how to actually quantify the effects of mis-aligned partitions. Some of the general information I found suggests the performance penalty can be quite high (upwards of 60%) and others say it's negligible. What I want to do is determine if partition alignment is a factor in this server's performance problems or not; and if so, to what degree? So I'll put my info out here, and hopefully the community can confirm if my partitions are indeed mis-aligned, and if so, help me put a number to what the performance cost is. Server is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for a big NFS share: [root@lnxutil1 ~]# parted -s /dev/sda unit s print Model: DELL PERC H700 (scsi) Disk /dev/sda: 134217599s Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 63s 465884s 465822s primary ext2 boot 2 465885s 134207009s 133741125s primary lvm [root@lnxutil1 ~]# parted -s /dev/sdb unit s print Model: DELL PERC H700 (scsi) Disk /dev/sdb: 5720768639s Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 34s 5720768606s 5720768573s lvm Edit 1 Using the cfq IO scheduler (default for CentOS 5.6): # cat /sys/block/sd{a,b}/queue/scheduler noop anticipatory deadline [cfq] noop anticipatory deadline [cfq] Chunk size is the same as strip size, right? If so, then 64kB: # /opt/MegaCli -LDInfo -Lall -aALL -NoLog Adapter #0 Number of Virtual Disks: 2 Virtual Disk: 0 (target id: 0) Name:os RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:65535MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 ... physical disk info removed for brevity ... Virtual Disk: 1 (target id: 1) Name:share RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:2793344MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 If it's not obvious, virtual disk 0 corresponds to /dev/sda, for the OS; virtual disk 1 is /dev/sdb (the exported home directory tree).

  Read the article

• ZFS/Btrfs/LVM2-like storage with advanced features on Linux?

  - by Easter Sunshine

  I have 3 identical internal 7200 RPM SATA hard disk drives on a Linux machine. I'm looking for a storage set-up that will give me all of this: Different data sets (filesystems or subtrees) can have different RAID levels so I can choose performance, space overhead, and risk trade-offs differently for different data sets while having a few number of physical disks (very important data can be 3xRAID1, important data can be 3xRAID5, unimportant reproducible data can be 3xRAID0). If each data set has an explicit size or size limit, then the ability to grow and shrink the size limit (offline if need be) Avoid out-of-kernel modules R/W or read-only COW snapshots. If it's a block-level snapshots, the filesystem should be synced and quiesced during a snapshot. Ability to add physical disks and then grow/redistribute RAID1, RAID5, and RAID0 volumes to take advantage of the new spindle and make sure no spindle is hotter than the rest (e.g., in NetApp, growing a RAID-DP raid group by a few disks will not balance the I/O across them without an explicit redistribution) Not required but nice-to-haves: Transparent compression, per-file or subtree. Even better if, like NetApps, analyzes the data first for compressibility and only compresses compressible data Deduplication that doesn't have huge performance penalties or require obscene amounts of memory (NetApp does scheduled deduplication on weekends, which is good) Resistance to silent data corruption like ZFS (this is not required because I have never seen ZFS report any data corruption on these specific disks) Storage tiering, either automatic (based on caching rules) or user-defined rules (yes, I have all-identical disks now but this will let me add a read/write SSD cache in the future). If it's user-defined rules, these rules should have the ability to promote to SSD on a file level and not a block level. Space-efficient packing of small files I tried ZFS on Linux but the limitations were: Upgrading is additional work because the package is in an external repository and is tied to specific kernel versions; it is not integrated with the package manager Write IOPS does not scale with number of devices in a raidz vdev. Cannot add disks to raidz vdevs Cannot have select data on RAID0 to reduce overhead and improve performance without additional physical disks or giving ZFS a single partition of the disks ext4 on LVM2 looks like an option except I can't tell whether I can shrink, extend, and redistribute onto new spindles RAID-type logical volumes (of course, I can experiment with LVM on a bunch of files). As far as I can tell, it doesn't have any of the nice-to-haves so I was wondering if there is something better out there. I did look at LVM dangers and caveats but then again, no system is perfect.

  Read the article

• Hide non VHD partitions

  - by James

  Hey! I have two partition on my HDD: C and D. On D: I have a vhd image (with windows 7 ultimate) that I use to boot from. When I'm running the OS from VHD I can still access my physical parititons. Is it possible to dismount them, in order to see just the virtual disks in the VHD OS? I tried with the physical C and it says that I cannot dismount a boot paritition and I think D cannot be dismounted because the VHD is on it.

  Read the article

• where on disk is space allocated for new files inside LVM lv with ext4 file system?

  - by Jost

  I run a multi-disk server with LVM2. Several large disks serve as LVM2 physical volumes for one volume group, containing one logical volume formatted with ext4. Nothing fancy, just your standard linear setup. Recently an additional, very small disk was added as physical volume to that volume group and I expanded both the logical volume, and the ext4 file system therein onto that disk. This lv is used to store incremental backups using rsync and is only about 30% full, there have rarely been any files deleted from it, only incremental writes. Now this new HDD I added to the pre-existing volume group has unexpectedly died on me, and the volume group won't come up because it is missing one physical volume. As fate will have it, this WAS the "in an event of catastrophic failure on the primary server"-backup, the event happened, the boss is not happy, so this kinda has to work... According to this (Part 3): http://www.novell.com/coolsolutions/appnote/19386.html it is possible to trick LVM into starting anyway by creating a new pv with identical metadata to the failed disk, which will make the volume accessible, but of course leave giant holes in the file system. I have'n tried it yet, because it involves repairing (writing to) the file system which eliminates the possibility of trying other things if it fails. Now my question is: How does this setup actually allocate disk space for new data? Is it allocated linearly from beginning to end of PVs, in the order they were added to the vg? Is it striped somehow in order to increase performance/balance load? since this defective disk was added only later to an existing lvm2 vg and lv, containing a half-empty ext4, what are the chances that there was never any data written to the defective disk? In other words: what are the chances of recovering all my data, even without the defective disk, by just starting the volume group as-is? Am I about to go spend $1500 on having 250GB of empty space recovered when I send the defective disk in for repair? Is there a way to check without mounting the file system and opening the files, hoping they contain something other than zeros? (comparing addresses of used data blocks inside ext4 to address ranges that were on the missing pv, something like that, preferably easy to automate) I know bitwise-copying the entire lv into an image file before trying to repair the ext4 would probably be a good idea, but since this lv is very large and I just suffered major file system failure on several systems it is probably a luxury I don't have... Any suggestions?

  Read the article

• Are there any FIPS-140-2 certified solutions for Linux?

  - by Mark Renouf

  I'm not even 100% certain what this involves, but my current understanding is this: use of only approved cryptographic algorithms for network traffic (easy, we use SSL and lock down the algorithms to only the really strong ones). Some form of physical data protection, involving disk encryption and physical tamper evident packaging. Obviously we're on our own if we need a tamper-proof product. But what about software for encrpytion. My guess is just using LUKS (although secure) will not be certified because it's open source (gov't seems a bit biased towards proprietary solutions here). Guardian Edge was mentioned by someone, but that appears to be complete Windows-based. So we need something like it, certified FIPS-140 compliant we can use on Linux.

  Read the article

• “Disk /dev/xvda1 doesn't contain a valid partition table”

  - by Simpanoz

  Iam newbie to EC2 and Ubuntu 11 (EC2 Free tier Ubuntu). I have made following commands. sudo mkfs -t ext4 /dev/xvdf6 sudo mkdir /db sudo vim /etc/fstab /dev/xvdf6 /db ext4 noatime,noexec,nodiratime 0 0 sudo mount /dev/xvdf6 /db fdisk -l I got following output. Can some one guide me what I am doing wrong and how it can be rectified. Disk /dev/xvda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders, total 16777216 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvda1 doesn't contain a valid partition table Disk /dev/xvdf6: 6442 MB, 6442450944 bytes 255 heads, 63 sectors/track, 783 cylinders, total 12582912 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvdf6 doesn't contain a valid partition table.

  Read the article

• Problem with Windows activation on a VM (Virtual machine)

  - by Daisetsu

  I backed up a number of laptops to virtual machines before they are to be re-purposed, in case I need the data at some later time. While the Physical to VM processes worked fine I am encountering issues on some of the VMs. When I boot them I get an error message saying I MUST activate windows in order to login. This is expected because the hardware changed (from physical hardware to virtualized hardware). I click the OK button and expect to be prompted with ways to activate, windows sits there for quite a while then tells me that "Windows has already been activated". I click OK at that message and get take back to the beginning where I am asked to activate Windows. I have done some fairly intensive googling but haven't been able to find a real solution. EDIT: The laptops with the issues are 2 Sony Vaios, I believe that they have the OEM version of the OS originally installed by the factory.

  Read the article

• Raid HDD Boot up

  - by user234695

  My server is Power Edge 1950 running server 2008 32Bit, using 3 Physical SAS HDD as a Virtual 2 Disk configured for RAID5, with partition of C drive as OS and D drive as Data. Planning to format and install Server 2008 R2 64Bit so I insert a New Physical disk and configured as RAID5 and clone the C drive and D drive to the new hard disk. Now I need to test that the new hard disk is able to boot windows and work as expected. How do I test, I am not able to boot the windows by choosing the new harddisk, the bios show only the existing HDD, not the new one. Also, if I remove the old three hard disk, and leave the new harddisk and then am I able to boot the device, if I do this does my existing RAID5 configuration and data on the hard disk still remain.

  Read the article

• Sizing a Virtual Server

  - by vdubs

  I would like to replace four aging physical servers with one virtual server. What is the best way to insure the VM server is sized correctly? The requirements of the apps that will be running on the four servers are APPLICATION SERVERS - QTY 3 - These will run the application layer for the web server, Business Objects Business Intelligence app, and various other small client server apps. The three most heavy hitting apps each have the following server requirements. So, if I bought three physical servers, this would be the requirements for each of them Processor - Dual 2.83 GHZ (or faster) Ram - 4 GB Raid 5 - 50-100GB usable space NIC - 1 GB Web Server - this will run one asp.net e-business app that will talk to our dedicated SQL server and the three app servers above. The E-Business software has these requirements for the web server Processor - Quad 2.83 GHZ (or faster) Ram - 8 GB Raid 5 - 50-100GB usable space NIC - 1 GB What is the best tool to determine what I need from a hardware standpoing in a virtual server? I am planning on using VMWare.

  Read the article

• NIS client cannot find NIS server (Opensuse)

  - by Tony

  I installed NIS server on head node of a virtual cluster(VirtualBox). One of the node (let's say node-1) can find NIS server and work with it, but another node (node-2) just can't find the NIS server in Yast while it can ping and ssh to both head node and node-1. BTW, all the nodes are VMs, head node and node-1 are on the same physical machine, node-2 is on another physical machine. I set the domain name in /etc/hosts and /etc/yp.conf, and ypwhich sometimes gives the correct domainname several minutes later complains about "ypwhich: Can't communicate with ypbind", and will back to work after some time. Also tried rpcinfo -p hostname and it worked as expected. I almost tried every thing I can find on internet, but seems that not many people had this problem. Any help would be very appreciated.

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• FortiGate firewall configuration with /30 and /28 networks

  - by slyderc

  I have fiber coming in from a new ISP which is being handed off via Ethernet on a single physical port. I'm having doubts about how to approach the configuration on my FortiGate 200A firewall because I've been given a /30 containing the ISP's gateway and another /28 for external IPs I can use: x.y.76.12/30 (.13 is the GW) x.y.76.64/28 (public IP space) How do I configure the FG200A's WAN1 interface to be aware of the two networks? As I only have one physical ISP port, will I need to plug it into a switch to break-out two cables and use a DMZ port on the FG200A for setting up the /28? Thanks in advance for your insight!

  Read the article

• backing up a virtual machine

  - by ErocM

  I inquired with the support of justcloud.com telling them that I have a vmware vm that I was wondering if it could be backed up while in use. I can back up the vm once it is shut down but I was wondering if their "shadow copy" would back it up while running. This was their response: Thank you for your email. I am really very sorry but virtual machines can't be backed up for a simple reason that they are virtual, they have virtual memory, not physical memory. Please let me know if there is anything else I can help with. Kind Regards, Barry James User Experience Team www.justcloud.com These are physical files so I wasn't sure I even understood the response. Am I wrong in thinking that a vm can be backed up while in use? Does this response even make sense? I need a cheap alternative to backing up the vm off the server in case it goes down. Any suggestions?

  Read the article

• Ghost Image - windows asks for activation on when deployed to VM

  - by Chris Sobolewski

  I have several images created with Ghost Solution Suite (v11 I believe), the images have been in use for a few years now, but I am finally to the point where I have enough time to attempt to virtualize them for easier updates. I am running VMWare and attempting to image the virtual machines with my ghost image files. For my images I am running sysprep with minisetup and using reseal. The image deploys successfully, however when I start the VM for the first time, it demands windows activation. This doesn't happen when I image a physical computer, even a different model with different hardware. The idea of virtualizing my images becomes rather worthless if I am unable to deploy the images without having to activate every time (especially as Microsoft keeps declaring our volume licence key as invalid for activations). Does anyone know why it is asking for activation on a virtual machine, but not a physical PC? How can I prevent this?

  Read the article

• Why does installing NVidia 9600GT graphics card, take 1GB of RAM away from Windows?

  - by Nick G

  Hi, I've changed graphics cards in my PC and now Windows 7 (32bit) is reporting that I have a whole gigabyte less physical RAM in my PC. Why is this? Firstly, the machine has 4GB of physical RAM. The old card was an ATI 2600XT with 256MB and the new card is an NVidia 9600GT with 512MB. With the ATI card windows sees 3326MB. With the NVidia card, windows sees 2558MB. I realise that due to address space restrictions I will not see all 4GB with 32bit windows, but why is there such a massive loss of RAM when simply changing cards (bearing in mind BOTH cards have their own RAM and borrow no main memory like some built on chipsets do). Would using 64 bit windows solve this? Thanks Nick.

  Read the article

• upgrade from windows server 2008 r2 std to enterprise

  - by Ravi

  We recently had to upgrade our servers from Win 2008 R2 Standard to Enterprise. The upgrade method was DISM. After the upgrade, a lot of weird things started to happen. Though Windows says it's been properly activated, we lost 1) RDP settings (disappeared from the Remote Setting tab of Properties of My Computer) 2) The option to join a domain is grayed out 3) The server had to 2 physical processors 12 cores each. Now, task manager or windows sees only 1 processor (or only 12 cores) 4) the amount of physical ram on this sever is 32 GB (Windows reports only 4 GB are usable) Has anyone encountered this before ? Thanks Ravi

  Read the article

• How can I secure Postgres for remote access when not in a private network?

  - by orokusaki

  I have a database server on a VMWare VM (Ubuntu 12.04.1 LTS server), and it just occurred to me that the server is accessible via the web, since the same physical server contains a VM that hosts public websites. My iptables in the database are such that only SSH traffic, loopback traffic, and TCP on port 5432 are allowed. I will only allow host access to the Postgres server from the IP of the other VM on the same physical machine. Does this seem sufficient for security, assuming there aren't gaping holes in my general OS configuration, or is Postgres one of those services that should never be web facing, (assuming there are some of "those"). Will I need to use hostssl instead of host in my pg_hba.conf, even though the data will travel only on my own network, presumably?

  Read the article

• Minimum space required for Server 2008 R1 install?

  - by Chris J

  I'm trying to plan disk space for a virtual environment, and wanting to keep virtual disks as small as possible - mostly as apart from the base OS, the software going onto the VM is less than a few MB, so want to avoid physical disk space going to waste; plus it'll give me an idea of how many VMs I could physically fit in {x}GB of physical drive. For Server 2003, I've had installs on 2GB and 5GB sized virtual disks. However for Server 2008, Microsoft recommends a minimum of 10GB (I assume this is both for x32 and x64). For the record, I will be installing the x32 version. Now I know I could just go ahead and try a small install, but wanted to solicit any practical knowledge as well :-) What's the smallest install of Server 2008 possible? (excluding server core installations).

  Read the article

• Two subnets on one switch with no VLAN and possible problems

  - by casey_miller

  As far as I know in order to use two subnets on one physical cable VLAN's are recommended. However, is it possible to achieve this (i.e: two subnets on one physical network) like 192.168.1.0/24 and 10.0.0.0/8 networks. What kind of problems or hidden rocks this way contains? With VLAN's it's possible to better isolate so users wouldn't easly sniff the other network. But in my environment it's okay if user on one subnet could listen to the traffic on another network. Is it the only problem?

  Read the article

• emulate fake monitor on windows 7?

  - by Claudiu

  Is there any way to emulate a monitor on Windows 7? I have one physical monitor, and I want Windows to think I have two. I actually don't care whether the second monitor is visible anywhere, or if I can see it - everything rendered there may as well go to the equivalent of /dev/null - but I need Windows to think there is one there. The reason is that I want to run a virtual machine with two monitors with VirtualBox in seamless mode, and it doesn't let me go to seamless mode if there are more virtual monitors than physical ones. I don't need to see the second virtual monitor, but VirtualBox won't just stop displaying it like it did in earlier versions.

  Read the article

• Using WebSphere CloudBurst with PowerVM to AIX virtualization over a cloud

  - by ADD Geek

  hi there we are studying the virtualization option to reduce our datacenter cost, and this research was assigned to me. we looked into alternatives and we almost reached a conclusion that PowerVM is the only option to virtualize pSeries servers. we found no signs of cloud support explicitly mentioned in any document, however there was the mention of CloudBurst. from the videos we watched and the documents we read, it seems that CloudBurst is more oriented towards Application Servers (WebSphere Software). but our environment is not relying only on WebSphere. we have some banking applications, Oracle Databases and MQ/Broaker. the question is: 1- can we virtualize the existing applications (all running AIX) on a cloud running on top of some of the existing servers? (given that we do the sizing properly) 2- is PowerVM to run on top of CloudBurst? 3- if the above solution is applicable, is this some sort of HA solution (since the VM will run on top of multiple physical boxes, while the same physical box will run multiple live images) thanks for your help

  Read the article

• Apache SSL losing session over load balancer

  - by SaltyNuts

  I have two physical Apache servers behind a load balancer. The load balancer was supposed to be set up so that a user would always be sent to the same physical server after the first request, to preserve sessions. This worked fine for our web apps until we added SSL to the setup. Now the user can successfully login, see the home page, but clicking on any other internal links logs the user right out. I traced the issue to the fact that while initial authentication is performed by server 1, clicking on internal links leads to having the request sent to server 2. Server 2 does not share sessions with server 1, and the user is kicked out. How can I fix it? Do I need to share sessions between the two servers? If so, could you point me to a good guide for doing this? Thanks.

  Read the article

• hardware addressing and configurable addressing scheme

  - by Zia ur Rahman

  basically i want to ask question about configurable addressing scheme for LAN interface hardware. i have read about it from a book, some main points are given by a configurable addressing scheme provides a mechanism that a customer can use to set a physical address.The mechanism can be manual (the switches that must be set when the interface is first installed).or an electronic memory such as an EPROM that can be downloded from the computer(what does this means). Most hardware needs to be configured only once- configuration is usually done when the hardware is first installed. Question:Suppose a network administrator configures the LAN interface hardware (assigns the address) when he installs it. Now later on if he needs to change the physical address of the device can he change it? Or in this addressing scheme the hardware can only be configured once and we can not reconfigure it later on.

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >