Search Results

Search found 3463 results on 139 pages for 'physical'.

Page 34/139 | < Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >

• Discs in DVD Drive not being read

  - by I Heart Ubuntu

  Does anyone have an experience with Ubuntu that is no longer reading discs in the DVD drive? This is my first time Ubuntu does not see the disc :| The disc is fine and works on my other Ubuntu computers. The drive is there and powered. I can even type in eject in a terminal and the drive will open. Using the command: sudo lshw -C disk I am able to see info about my drive too. Actually BOTH of my internal DVD drives cannot read discs anymore. If the output is not readable below, here is the info in pastebin. http://pastebin.com/GqqSCTPw *-cdrom:0 description: DVD writer product: DVD_RW ND-3500AG vendor: _NEC physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom1 logical name: /dev/cdrw1 logical name: /dev/dvd1 logical name: /dev/dvdrw1 logical name: /dev/scd0 logical name: /dev/sr0 version: 2.1B serial: [_NEC DVD_RW ND-3500AG2.1B06022300BT-LIGGY capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: CDDVDW SH-S222A vendor: TSSTcorp physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: SB01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Deleting Unused Swaps Partions

  - by Nikita Kononov

  Good evening everyone , I got a little issue with Swap Partitions. Due to some issues after installing Ubuntu first time, I reinstalled it and now I have 3 Swaps. Here is sudo fdisk -l result Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xaa9693fe Device Boot Start End Blocks Id System /dev/sda1 2048 52430847 26214400 1c Hidden W95 FAT32 (LBA) /dev/sda2 * 52430848 540677076 244123114+ 7 HPFS/NTFS/exFAT /dev/sda3 540678142 1465147391 462234625 5 Extended Partition 3 does not start on physical sector boundary. /dev/sda5 1452750848 1465147391 6198272 82 Linux swap / Solaris /dev/sda6 1440352256 1452742655 6195200 82 Linux swap / Solaris /dev/sda7 540678144 1427951615 443636736 83 Linux /dev/sda8 1427953664 1440339967 6193152 82 Linux swap / Solaris So Swaps in /dev/sda5 and /dev/sda6 are no longer in use as far as I understand and thus I was planning to delete them, however faced a problem. What I did is download and burn Gparted Live CD and boot it up, tried to delete those partitions but I have no idea how to add 12GB unallocated memory to the existing OS partition in this case to /dev/sda7 Is there anyway I can delete 2 swaps and extend unallocated memory to /dev/sda7 partion? Thank you in advance!

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• SD Card only mounted after a reboot

  - by hattenn

  I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

  Read the article

• Ubuntu installation does not recognize drive partinioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Grub does not show a Windows 8 option after dual boot

  - by skytreader

  So, I've successfully dual-booted my Windows 8 machine with Ubuntu 12.04 . However, I still don't have a convenient method of choosing what OS to load at boot time. After installing Ubuntu, my computer still loads Windows 8 directly. I then added grubx64.efi to the white list of my boot loader. But after that, my machine loads Ubuntu directly without even a shadow of GRUB showing up! I used boot-repair and I got this paste.ubuntu URL: paste.ubuntu.com/1326074. After running boot-repair (and re-white listing the grubx64.efi file), GRUB now shows up but without any Windows 8 option! Lastly, I ran sudo fdisk -l and it gave me this: WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x6396389f Device Boot Start End Blocks Id System /dev/sda1 1 1465149167 732574583+ ee GPT Partition 1 does not start on physical sector boundary. I'm guessing my problem has something to do with the warning from fdisk above but I don't know what to do with it. How do I proceed now?

  Read the article

• Ubuntu server 11.04 recognize only 1 core instead of 4

  - by Kreker

  I searched for other questions and googled a lot but I don't find a solution for solving this problem. Ubuntu Server 11.04 64bit installed on Dell Poweredge with Intel Xeon X5450. He only recognize 1 of the 4 cores I have. Tried to modify the GRUB config but didn't work. IN the machine BIOS I didn't find anything useful. CPU root@darwin:~# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU X5450 @ 3.00GHz stepping : 10 cpu MHz : 2992.180 cache size : 6144 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dts tpr_shadow vnmi flexpriority bogomips : 5984.36 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: GRUB root@darwin:~# cat /etc/default/grub # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=2 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="" GRUB_CMDLINE_LINUX="noapic nolapic" #was with acpi=off # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" Complete dmesg Too long, posted on pastebin http://pastebin.com/bsKPBhzu

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• Why does Ubuntu 13.10 not detect my Win7 partition?

  - by goutham

  I'm trying to install Ubuntu 13.10 alongside Windows 7 on my DELL INSPIRON 14z 5423 laptop and I'm new to all of this. I'm using the Ubuntu 13.10 64-bit ISO burned onto a CD. The first time I tried to install it, Ubuntu said it did not detect any other OS, which meant I only had 4 options: Erase disk and install Ubuntu (I don't want to do this) Encrypt new Ubuntu. Use LVM. Something else. If I choose the Something else option, it brings me to the partition menu and says that I have 1 disk with free space of (500Gb), but that's not true because I have Windows 7. I restarted the laptop several times and booted the CD again and I got exactly the same as I did previously. How do fix this problem and install Ubuntu alongside Windows 7? After executing "sudo fdisk -l" command in terminal ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 314574847 157184000 7 HPFS/NTFS/exFAT /dev/sda3 314574848 629147647 157286400 7 HPFS/NTFS/exFAT /dev/sda4 629147648 976771071 173811712 7 HPFS/NTFS/exFAT After removing one partition I executed command once again ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 629145599 314469376 7 HPFS/NTFS/exFAT /dev/sda3 629147648 976771071 173811712 7 HPFS/NTFS/exFAT

  Read the article

• How to Manage and Use LVM (Logical Volume Management) in Ubuntu

  - by Justin Garrison

  In our previous article we told you what LVM is and what you may want to use it for, and today we are going to walk you through some of the key management tools of LVM so you will be confident when setting up or expanding your installation. As stated before, LVM is a abstraction layer between your operating system and physical hard drives. What that means is your physical hard drives and partitions are no longer tied to the hard drives and partitions they reside on. Rather, the hard drives and partitions that your operating system sees can be any number of separate hard drives pooled together or in a software RAID Latest Features How-To Geek ETC Inspire Geek Love with These Hilarious Geek Valentines How to Integrate Dropbox with Pages, Keynote, and Numbers on iPad RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin How to Kid Proof Your Computer’s Power and Reset Buttons Microsoft’s Windows Media Player Extension Adds H.264 Support Back to Google Chrome Android Notifier Pushes Android Notices to Your Desktop Dead Space 2 Theme for Chrome and Iron Carl Sagan and Halo Reach Mashup – We Humans are Capable of Greatness [Video] Battle the Necromorphs Once Again on Your Desktop with the Dead Space 2 Theme for Windows 7

  Read the article

• How to install Ubuntu 12.04.1 in EFI mode with Encrypted LVM?

  - by g0lem

  I'm trying to properly install Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with the alternate install CD ".iso" on a lenovo Thinkpad X220. Default Hard Disk (with a pre-installed version of Windows 7) has been replaced with a brand new SSD. The UEFI BIOS of the lenovo Thinkpad X220 is set to "UEFI Boot only" & "USB UEFI BIOS Support" is enabled (I'm using an external USB DVD reader to perform Ubuntu installation). The BIOS is a Phoenix SecureCore Tiano, BIOS version is 8DET56WW (1.26). The attempts below are made with the UEFI BIOS settings described above. Here's what I've tried so far: Boot on a live GParted CD Create a GPT partition table Create a FAT32 partition for UEFI System, set the partition to "EF00" type ("boot" flag) Leave remaining space unformated Boot on Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with alternate CD: Perform the install with network updates enabled Use manual partitioning FAT32 partition created with GParted is used as "EFI System partition" Remaining space is set to be used as "Physical volume for LVM" Then "Configure encrypted volumes" using the previous "Physical volume for LVM" as the encrypted container, passphrase is setup. "Configure the Logical Volume Manager" creating a volume Group using the encrypted container /dev/mapper/sda2_crypt Creation of the Logical Volumes "Create logical volume", choosing the previously created volume Group Assign a mount point and file system to the Logical volumes : LV-root for / LV-var for /var LV-usr for /usr LV-usr-local for /usr/local LV-swap for swap LV-home for /home NOTE: /tmp would be in RAM only using TMPFS Bootloader step: neither my ESP partition (/dev/sda1, /dev/sda or MBR) seems to be the right place for GRUB, I get the following message (X suffix is for demonstration only): unable to install grub in /dev/sdaX Executing 'grub-install /dev/sdaX' failed This is a fatal error. Finish installation without the Bootloader & Reboot The system doesn't start, there's no EFI/GRUB menu at startup. What are the steps to perform a clean and working installation of Ubuntu 12.04.1 Precise Pangolin, 64bit version in U(EFI) mode using the encrypted LUKS + LVM scheme described above?

  Read the article

• Problem with APTonCD application

  - by Harikrishnan

  I created a iso image using aptoncd & burned it to a dvd. now when i tried to restore, the program does not detect the dvd in the drive. It shows "Please insert a disc in the drive." and if we click "ok" it shows "E: Failed to mount the cdrom.". The dvd is in the drive itself. I tried "sudo lshw -C disk" and the out put is: *-cdrom description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 logical name: /media/APTonCD logical name: /media/apt version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted status=ready *-medium physical id: 0 logical name: /dev/cdrom logical name: /media/APTonCD logical name: /media/apt configuration: mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted Then i checked in disk utility application. in that dvd rom is shown as "/dvd/sr0". my ubuntu version is 10.10. please help me to solve the problem.

  Read the article

• How do I know if I'm getting the most out of my video card?

  - by b.long

  My computer at home is a bit lacking, so I want to make sure I'm getting the most out of it while I can. Generally speaking, here are the specs: 4GB Memory AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ × 2 64-bit Ubuntu The terminal shows me the following: me@home:~$ uname -a Linux home 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 20:45:39 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux me@home:~$ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] me@home:~$ sudo lshw -C video *-display:0 description: VGA compatible controller product: RV380 [Radeon X600 (PCIE)] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:e0000000-efffffff ioport:ac00(size=256) memory:fdef0000-fdefffff memory:fdec0000-fdedffff *-display:1 UNCLAIMED description: Display controller product: RV380 [Radeon X600] vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress bus_master cap_list configuration: latency=0 resources: memory:fdee0000-fdeeffff me@home:~$ lspci -nn | grep VGA 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] [1002:5b62] The additional drivers menu in System Settings shows me nothing useful and my attempt at installing ATI's Catalyst Control center (drivers that came with the video card) failed. I believe the latest version of Ubuntu at the time was 9.x. What should I do? Install an old version of Ubuntu 9? Use some alternative driver? UPDATE: I might try my hand at a bit from this answer next: "Installing Catalyst Manually (from AMD/ATI's site)" . From a terminal, fgl_glxgears returns *"fgl_glxgears: command not found"*. Any thoughts?

  Read the article

• Desktop goes blurry / granulated

  - by Bonfire

  After few minutes using, desktop and fonts in unity-menu goes blurry. See screenshot.! In all applications (browser etc.) graphics seem to be allright. After rebooting problem disappears for few minutes. Changing the wallpaper also makes the desktop clear (for a while) but fonts are still blurry. I have ubuntu 12.04 and windows xp dualbooted. lspci: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) lshw -c video: *-display:0 description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0100000-d017ffff ioport:30c0(size=8) memory:c0000000-cfffffff memory:d0180000-d01bffff *-display:1 UNCLAIMED description: Display controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 02 width: 32 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:40000000-4007ffff Have you got any ideas to get this solved? Thank you very much! Bonfire

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

• Banshee gapless playback does not work when playing mp3s

  - by ComputerGuy505

  Even though I have gapless playback enabled in Banshee's settings menu, there is a very short pause between songs. This might be due to the fact that my hard drive's partitions seem wierd. fdisk -l produces this output: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4a73c3cb Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 724153740 361872070+ 7 HPFS/NTFS/exFAT /dev/sda3 1456826368 1465145343 4159488 c W95 FAT32 (LBA) /dev/sda4 724154366 1456826367 366336001 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 1440159744 1456826367 8333312 82 Linux swap / Solaris /dev/sda6 724154368 1440159743 358002688 83 Linux Partition table entries are not in disk order Playing mp3's from /dev/sda2 or /dev/sda6 produces this problem. I don't seem to have gapless playback on Rhythmbox or Clementine either, if those media players are supposed to have it. I'm not sure what other info to provide. This is just annoying to me. Thanks for any help.

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

• How to write code that communicates with an accelerator in the real address space (real mode)?

  - by ysap

  This is a preliminary question for the issue, where I was asked to program a host-accelerator program on an embedded system we are building. The system is comprised of (among the standard peripherals) an ARM core and an accelerator processor. Both processors access the system bus via their bus interfaces, and share the same 32-bit global physical memory space. Both share access to the system's DRAM through the system bus. (The computer concept is similar to Beagleboard/raspberry Pie, but with a specialized accelerator added) The accelerator has its own internal memory (SRAM) which is exposed to the system and occupies a portion of the global address space (as opposed to how a graphics card would talk to teh CPU via a "small" aperture in the system memory space). On the ARM core (the host) we plan on running Ubuntu 12.04. The mode of operation of communicating between the processors should be that the host issues memory transactions on the system bus that are targeted at the accelerator internal memory. As far as my understanding goes, if I write a program for the host that simply writes to the physical address of the accelerator, most chances are that the program will crash due to a segmentation violation. So, I assume that I need some way of communicating with the device in real mode. What is the easiest way to achieve this mode of operation?

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• alsa - sound issues on ubuntu 12.04

  - by tam_ubuuser

  i am having an sony E series laptop.i have an HDMI port .at this stage ,i have tested my sound card , which provides audio out on my laptop i.e i could hear songs .my laptop has two sound cards amd 5450 and an intel-hda(alsamixer shows that as s/pdif) . i decided to connect HDMI output to my new HD-TV.but, i could get only visuals on my TV,NO AUDIO OUTPUT ( HDMI cable works fine with win 7).my laptop has two sound cards.but i couldn't switch output to other card.( i don't know ,how to do that) i decided to update alsa. complied the following code in terminal. sudo apt-add-repository ppa:ubuntu-audio-dev/alsa-daily sudo apt-get update sudo apt-get install alsa-hda-dkms then,strangely no login sound, and no audio output on my laptop at all .then, started complied code from step1 sound troubleshooting procedure from offical ubuntu site.then, my speaker icon taskbar disappeared .obivously $aplay -l ,provided output as no soundcards detected . so , i implemented step 4 from that guide, it provides a output of all hardware devices in my laptop. *-multimedia UNCLAIMED description: Audio device product: Cedar HDMI Audio [Radeon HD 5400/6300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:f0040000-f0043fff *-multimedia UNCLAIMED description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f5e00000-f5e03fff that command displayed output name of the two cards . but , still i have no positive output on $aplay -l. so therfore, i think alsa couldn't detect my sound cards . is there solution to this problem? it could be better,if alsa would channel output from multiple sound cards ? how should install and configure alsa such that detects HDMI cable as soon i connect to my HD tv? is it possible to alsa and pluseaudio 2.0 to co-exist, if so how?

  Read the article

• SD Card only mounted after a reboot

  - by evothur

  Hi everyone. I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

  Read the article

• Are Windows partitions gone?

  - by Gigili

  I had Windows 7 on my laptop (factory setting), because of some performance issues, I decided to use recovery options to restore it to its factory condition but I don't know what has happened or what I have done that the whole operating system was gone after playing around with recovery options from the boot menu. I couldn't find Windows, so I installed Ubuntu 11.04 on my laptop. Last time I had Ubuntu on it, it was not really compatible with laptop's configuration and I had a bit of problems trying to do normal tasks I used to do on Windows. Now I want to make sure that Windows and its drivers are gone so that I can try to install a newer version of Ubuntu or Windows. I tried the command sudo fdisk -l And the result shown was: myaccount@myaccount-VPCS116FG:~$ sudo fdisk -l [sudo] password for myaccount: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00025b5f Device Boot Start End Blocks Id System /dev/sda1 * 1 38409 308515840 83 Linux /dev/sda2 38409 38914 4052993 5 Extended /dev/sda5 38409 38914 4052992 82 Linux swap / Solaris Disk /dev/dm-0: 4150 MB, 4150263808 bytes 255 heads, 63 sectors/track, 504 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xa668cfe8 Disk /dev/dm-0 doesn't contain a valid partition table Is it gone? If not, what command should I try to have access to Windows partitions? Thank you.

  Read the article

< Previous Page | 30 31 32 33 34 35 36 37 38 39 40 41  | Next Page >