Search Results

Search found 1587 results on 64 pages for 'ultimate'.

Page 30/64 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• What causes Windows Boot to stall?

  - by Nick Berardi

  For about 6 months now I have been having this weird problem where Windows 7 fails to fully boot correctly. What happens is this. Starting Windows shows up on the screen. Then 3 out of 4 times nothing else happens, no Windows Flag animation, just nothing occurs. After 3 or 4 restarts repeating steps 1-2 above, the Windows Flag animation finally shows up and everything works as expected. My question is what is causing this problem in steps 1 and 2? Because I have tried the following with no luck: Error checking and correcting of any disk errors Updating drivers Doing a clean install of Windows 7 My setup is as follows: Windows 7 64-bit Ultimate 8 GB RAM 128 GB Crucial SSD (firmware 0005) Dell Latitude E6410 Intel Wireless and Graphics Other than what I have tried above I am totally out of ideas and looking for some new ones to try.

  Read the article

• Grapher: Edit Equations Without GUI

  - by Nathan G.

  I'm trying to edit the equation of a Grapher file without opening the Grapher UI. I've gotten as far as knowing that I need a hex editor to do this. I can't, however, find my equation in that file to change it. Does anyone know how Grapher stores this information, and how to change it? My ultimate goal is to be able to change the file through the shell so I can open it and have Grapher show me my new equation (that was set with the CL). Thanks! I will set a bounty if necessary.

  Read the article

• Clone a 2TB WD Green internal drive with bad sectors to a 3TB partitioned external

  - by ron

  I have a 2TB WD Black drive and would like to simply do a straight clone from a failing 3TB drive to it. Both are SATA. Will I be able to just install the new drive alongside the faulty one and then do the clone/rescue attempt with ddrescue or is there a better method? The faulty internal drive mentioned has bed sectors although am usually able to boot into Windows 7 Ultimate with it and navigate and access all my programs. I have been attempting some trials with an Ubuntu Live CD using ddrescue but am not sure I'm doing it right. I have a 3TB WD my book essential external which is GPT and have created a separate 2TB partition on it which I am trying to clone to. I assume I need to format the new drive first to NTFS? Can I do that via the Ubuntu Rescue Remix 12-04 live DVD that I've been booting with?

  Read the article

• Tool that automatically keeps old versions of a file? Shadow Copy in Win7?

  - by Michael Stum

  When I'm working with a Graphics App, I press CTRL+S a lot to Quicksave. Sometimes, I just went too far and made a bad decision, sometimes to the point Undo wouldn't help either. I would love to retain old versions of a file. Normally, Source Control would be of use here, but that's a manual process (same as just making some copies). I wonder if there is an automatic way to do that? Everytime the file changes, keep a backup. I believe that in Windows Server, Shadow Copies can do that. When I check in my Windows 7 (Ultimate), I do see "Previous Versions" as a tab, but that seems to be part of the backup function which is once again manual. Is there a way to get that type of automatic versioning?

  Read the article

• How do I establish the network sharing to my WinXP server network drive from my Mac notebook?

  - by mobibob

  I have been able to connect to my WinXP server's shared drives by using Finder's Command-K to browse the network. Unfortunately, when the server gets rebooted, the connection drops and sometimes I cannot get reconnected. I have specified different protocols (afp / cifs / smb) and different login names (connect as...) with limited success. Once I find the right combination, I am good for a few weeks. Once, it seems as though I had to unshared and shared the drive to get it to work. Unfortunately, it is very frustrating, so I try multiple things at one time, so when I finally get to the success point -- I honestly don't know what worked. I followed Mac help, surfed for instructions, issues, etc., but nothing appears to be consistent. I would love for this thread to be the ultimate answer for all time! Can anyone help me? If my description or question need more detail, please ask away!

  Read the article

• Unable to diagnose Windows 7 lockup

  - by Delyan

  Basic info: Laptop Dell Studio XPS 13 (Intel P9600, 4GB RAM, NVidia 9400M card, 256G Samsung PM800 SSD) Windows 7 Ultimate, as well as Fedora 14 Here's the deal - Windows would just lock up out of nowhere, no log entries, no dumps, no BSOD, it just freezes. This happens mostly when idle (but it happened when I was using it too) and does not follow a concrete time frame. No input is accepted - only solution is to hold the power button. Although this sounds like a clean cut hardware issue, the reason I'm willing to rule this out is that my primary OS is Fedora 14. It's been working fine for the past 2 years and I've been stress testing the hardware (intentionally or not) every once in a while with no issues. I would like to ask if there's any way to get a diagnostic output from Windows in a situation such as this. The next step in my testing is to leave it in Safe Mode overnight and see if it locks up but even if I do that, I still need to figure out what component freezes it up during normal operation.

  Read the article

• Why am I seeing excessive disk activity when installing applications?

  - by Kev

  I'm running Windows 7 Ultimate 64 bit on a Dell Vostro 1720 with 8GB of RAM, 7200RPM Disk, 2.53 GHz Core2Duo (Windows 7 64 bit is a supported option and the laptop came with the OS pre-installed). I'm noticing some fairly excessive disk activity when running installers. For example the Visual Studio 2010 RC installer constantly accessed the disk for ~10 minutes. It was so excessive that I was unable to use the machine until this ceased. Today I installed Trillian Astra 4.1 for Windows (latest build from the website). Again when I ran the installer I was pretty much locked out of the machine until the disk activity calmed down. In both cases when I eventually managed to launch task manager I could see that the CPU was sitting at around 5% to 7% utilisation whilst this was going on. All other disk related activity is fine, the machine is snappy and applications launch without delay. It's just when I run an installer I see this odd behaviour. Why would this be?

  Read the article

• What caused Cyclic Redundancy Check error on my BitLocker-enabled external hard drive and how to fix it?

  - by Forgiver

  I have an external hard drive that is connected to my computer (Windows 7 Ultimate 64 bit) via a USB port. BitLocker has been activated on the hard drive to protect the data. Yesterday I started downloading a huge data from the internet but now it failed to complete because of CRC error. I tried to repair it with chkdsk f:/r where f is the drive letter of that hard drive. There are many messages reporting "unreadable" as follows: What caused Cyclic Redundancy Check error on my BitLocker-enabled external hard drive and how to fix it?

  Read the article

• How to customize Windows 7 HAL library during installation (BSOD STOP: 0x000000A5)?

  - by koldovsky

  While trying to install Windows 7 x86 Ultimate on Samsung M40 laptop (Pentium M 1.7 Dothan, 2 GB RAM/ 100 GB HDD) i receive BSOD STOP: 0x000000A5: The bios in this system is not fully ACPI compliant. Please contact your system vendor for an updated bios. The bios on the system is updated to latest version. If ACPI is the real source of the issue it means that I possibly could use another HAL library. In Windows XP it is possible to install system with generic HAL library pressing F7 when installer asks to supply drivers, but on Windows 7 I can't find such option. Ironically, Vista installs and works nice, even if they said that Windows 7 is less demanding for hardware. Windows 7 Advisor also tells nothing suspicious. Can anybody tell me how to customize Windows 7 installer to use generic HAL library (if it is possible, of course) or point me to another solution?

  Read the article

• Creating self-signed SSL certificate - Access denied?

  - by Shaul

  I'm trying to create a Self-Signed Certificate in IIS 7 (Win7 Ultimate x64), and getting the following error: I found this question on SF, which says I should set permissions on the C:\ProgramData\Microsoft\Crypto\RSA\MachineKeys folder to allow rights - but that's also not working. Firstly, note that "Everyone" has "Full Control" rights: And when I try to delete and recreate rights, look what comes up: I am logged in as a user with admin privileges, and I've even tried running Explorer with Admin rights... nothing seems to help. What do I do to get this right?

  Read the article

• Cannot connect to telnet server

  - by BloodPhilia

  So, I can't use telnet to connect to any server but it works fine from a different computer. It just says it can't connect. I tried the following things: Disable firewall and AV protection. (Basically, there was no security feature left online) Telnet is set to "Trusted" in my AV protection. (Kaspersky Internet Security 2011) Using Putty to telnet, but apparently Putty's connection is also inhibited. (Says it can't connect to host) Disabling the telnet client in Control Panel and then re-enabling it. (Windows 7 Ultimate) hosts file is clean. Checked for nasties using MBAM and KIS 2011 as well as going though my HijackThis logs, nothing found. I can connect to the same machines/servers through the web browser, ping, tracert, etc. Only telnet seems to be blocked. Any other thoughts?

  Read the article

• Cannot connect to telnet server

  - by BloodPhilia

  So, I can't use telnet to connect to any server but it works fine from a different computer. It just says it can't connect. I tried the following things: Disable firewall and AV protection. (Basically, there was no security feature left online) Telnet is set to "Trusted" in my AV protection. (Kaspersky Internet Security 2011) Using Putty to telnet, but apparently Putty's connection is also inhibited. (Says it can't connect to host) Disabling the telnet client in Control Panel and then re-enabling it. (Windows 7 Ultimate) hosts file is clean. Checked for nasties using MBAM and KIS 2011 as well as going though my HijackThis logs, nothing found. I can connect to the same machines/servers through the web browser, ping, tracert, etc. Only telnet seems to be blocked. Any other thoughts?

  Read the article

• Motherboard RAM question.

  - by winterwindz

  Firstly I'm new at this. Not a very computer-ish person. So I very much apologize if this is not the right place, but here it goes.. My Motherboard is an Asus P5LD2-SE. I'm running in Win 7 Ultimate 32-bit(x86) OS, 1GB RAM (2x512 MB). I'm planning to upgrade my OS to 64-bit and because I know my Motherboard is a dual-channel, I bought a dual-channel 2 GB RAM (2 pcs). My question is; am I still able use my old RAM ones, since it is 4 slots..? Which in the end will show 5GB. Is it possible? Thank you for your time. =)

  Read the article

• VMware 1.0.1 Windows7 - Ubuntu hostnames

  - by Kyle K

  I'm trying to run Ubuntu as the guest OS using VMWware 1.0.10 with Windows 7 Ultimate as the host OS. I had this set up previously with Win XP as the host OS and in fact I'm using the same .vmx My problem is I can't get either Win7 or Ubuntu to be able to ping the other by hostname. After installing Samba and Winbind on Ubuntu, I was able to get this working when under WinXP, but for some reason I can't get it to work under Win7. I can ping by IP Address, and the guest OS even shows up by hostname under the Windows networking panel (but of course I can't do anything with it), but pinging using short hostnames just won't work. Also, Win7 firewall is turned off completely.

  Read the article

• Windows 7 unresponsive after hibernate.

  - by Simon Verbeke

  The last few days, when I get Windows out of hibernate, Windows itself gets unresponsive. I can use any of my programs that were already opened before hibernating, but the window functions (closing, changing the size etc) aren't reacting. I can't open any new programs, except for the Task Manager. Also, I don't get an Internet connection. When I use Ctrl + Alt + Del, I get either a black screen, or the regular background. Then it hangs and after a while shows me a message that Windows failed starting up that "thing"(don't know what it's called in English, something with safety, etc). I have Windows 7 Ultimate installed.

  Read the article

• How to get Apache web server to run on other computers?

  - by Eric

  I have been using Apache Web Server for a while now and one thing I have noticed is that outside of my computer I can not access it. I use my Apache server for PHP development on my computer, but I would like to access stuff I have made outside of my computer. I am on a linksys router network. I usually run it of http://localhost/ or http://127.0.0.1/. I IPCONFIGED my computer and got 192.168.1.105 so I went there with my browser and got the page just fine. I tried doing this on another computer on the same network but it didn't work. How do I fix this? Sorry about the bad wording. I am in ah hurry Information you might need to know: Server: Apache 2.2 Operating System: Windows 7 ULTIMATE

  Read the article

• New video card? [closed]

  - by TutorialPoint

  I ran into some problems with my ATI Radeon x1200. I want it to support vertex shader 3.0, but it only does 2.0. This is because Call of Duty: Modern Warfare 2 only works with 3.0. So, I want a new video card. Can someone help me, with a more clean look to it? I bet if I would stick to some seller, I would end up with a video card that does not support what I want, or is too expansive. I really do not want it to be above $75, if possible. Some info about my PC: Manufacter: XXODD Processor: AMD Athlon64 X2 DualCore 4000+ 2Ghz (but running currently 32 bit OS) ATI Radeon X1200 video card (the problem) 1 GB RAM DDR2 MS-7367 Motherboard Windows 7 Ultimate OS 32-Bit Build 7600 RTM

  Read the article

• How to access USB stick content from VMWare running Ubuntu 10.10?

  - by JVerstry

  Hi, I am running Ubuntu 10.10 via VMWare under Windows 7. I have followed the procedure to install the USB stick. It is now connected to the host. However, I don't know how to access the content of the stick. My Google research indicates that this may be a mounting issue. I read somewhere that I should check /proc/bus/usb, but the usb directory does not exist in /proc/bus. Unfortunately, I am not a Linux expert at this. The ultimate issue I am trying to solve is the one describe here. I am trying to use vi to create ~/.vmware/config, but it is virtually impossible to use vi, since I don't have access to the arrow keys (chicken & egg problem). I have created the config file on my usb stick and want to copy it where it should be. Thanks!

  Read the article

• Chrome mouse lag

  - by Mike Pateras

  I recently upgraded to Windows 7 Ultimate (without reinstalling, an actual upgrade) and now I'm experiencing some really annoying mouse lag in Chrome. It seems to happen most often when there is a Flash element on the page, though that's not always the case. I have a Windows Experience base of 7.5 (I just re-ran it), 7.7 in desktop and gaming graphics, and Skyrim still runs fine. I ran an Intel chipset update and re-installed my Catalyst drivers (I uninstalled them first), and I don't have any available Windows Update. I've also re-installed both Chrome and Flash, and I've disabled all of my Chrome extensions. Nothing has helped. What might be causing this very annoying issue, and what might I do to fix it, short of reformatting? Thank you.

  Read the article

• how to troubleshoot shutdown problems in windows 7

  - by Ieyasu Sawada

  I have a desktop with windows 7 ultimate installed. Whenever I shut it down from the start button. The text that says that it is logging off and shutting down is present and the monitor blacks out and says no signal. But the lights in the RAM is still on and all the fans in the desktop is still spinning. Why is that? It seems like its not shutting down completely. I have also got disk problems lately. Event id 175 and 50. Which I think is caused by the computer not shutting down completely. How do I troubleshoot this one? Feel free to ask if you need more details, thanks.

  Read the article

• no UAC prompt when opening the Services applet

  - by Serge - appTranslator

  Not quite sure if this question is better asked here or on superuser.com Hi All, My Win7 Ultimate no longer 'UAC prompts' me when I open the services applet (administrative tools). I can manipulate services without ever confirming the elevation. Yes, UAC is still enabled. Yes, I've rebooted to make sure this is not due to a former UAC elevation of explorer.exe or so. It looks like a big security hole. Does anyone have an idea about the reason for this behaviour? Or how to investigate it? TIA,

  Read the article

• Firefox (on windows) constantly consuming 10% CPU - is there an add-in to find the rogue tab?

  - by tbone

  I often have many Firefox windows open, each with many tabs. Now and then one of the tabs will be running a web page that for some reason consumes lots of resources. Right now, I have a tab somewhere that is constantly consuming 10% of the CPU...which would be fine as my computer can easily handle that (see specs below...all other apps are responsive), but it seems to slow Firefox down....everything, everywhere is extremely laggy in Firefox, I can see pauses while I type this. Is there: - a way I can isolate separate instances (or even tabs) in FF into a separate process, so one rogue tab doesn't bog down FF across the entire system? - maybe an add-in that can either identify tabs consuming lots of CPU, or maybe a way to "shut down" activity on tabs you haven't used in a while? Firefox 3.6.10 Windows 7 Ultimate 64 i7 920 @ 3.6 GHz 12 GB Ram

  Read the article

• Is there a way to disable specific Spybot Immunization rules?

  - by Iszi

  I've been having problems using a desktop sharing application, which I've traced to the Immunization protections applied via Spybot S&D. Specifically, the problem has been narrowed down to the rules in the \SOFTWARE (Plugins) categories under the Internet Explorer groups. Once I disable these Immunization categories, everything in the application works fine. Each of these categories appears to include ~900 protections on the system. I suspect that the root cause of my problems could be narrowed down to just one, or perhaps a handful, of the settings that get applied in these categories. However, I can't find any options in Spybot S&D which would allow me to drill down to the individual protection rules and choose which to enable or disable. Is there something I'm missing, or is this not a feature available via the GUI? If it's not strictly supported in the application, is there a way to work around it by manually editing some of its files or registry settings? Spybot S&D version: 2.2.21.0 Spybot Start Center version: 2.2.21.129 Windows Ultimate x64

  Read the article

• Why can't I create a Windows backup on my secondary disk?

  - by Brian Sullivan

  I've installed Windows 7 Ultimate on an SSD that I've added to the XPS desktop that I bought from Dell. I would like to use the built-in backup functionality to create incremental backups and store them on the large drive that came with the machine. I formatted the large drive and turned it into a Basic disk. However, when I try to set the backup location to the large internal disk (E:\) in the "Set up backup" wizard, a get a message saying, "A system image cannot be saved on a drive that your computer boots from or that Windows is installed on." Windows is not installed on that disk. I even deleted the OEM partition that was on the disk, and removed it completely from the boot order in the BIOS. Any clue why Windows is griping at me about this?

  Read the article

• Workstation 7 build 203739 - Capture Movie Mouse Pointer Not Visible

  - by BMIVM

  Hi, I have noticed that whenever I create a Capture Movie, the movie is fine but the mouse pointer is not visible at all. The clicks are on buttons file menus are executed but is hard for a viewer of the capturre movie session to follow the recording smoothly. This was not a problem in previous versions of WorkStation. Is this a bug or is there a setting I can set to see the mouse pointer? Note: VM Tools are installed, Host is Vista Ultimate Edtion SP1, x64 and the guest is a Win XP SP2. Thanks in advance for your help.

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >