Search Results

Search found 9611 results on 385 pages for 'low power'.

Page 300/385 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• My desktop has started overheating -- how hot is hot?

  - by Jerry

  I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

  Read the article

• Ubuntu Device-mapper seems to be invincible!

  - by Andrew Bolster

  I'm working on a hopefully unrelated question question and I've got to a strange situation. First: I know very little about the very low level hardware kernal storage driver magix, so I'm hoping a) someone can help and b) someone can explain it to me better. I've been trying a dozen different configurations of my 2x500GB SATA drives over the past few hours involving switching between ACHI/IDE/RAID in my bios; After each attempt I've reset the bios option, booted into a live CD, deleting partitions and rewriting partition tables left on the drives. Now, however, I've been sitting with a /dev/mapper/nvidia_XXXXXXX1 that seems to be impossible to kill! its the only 'partition' that i see in the Ubuntu install (but I can see the others in parted) but it is only the size of one of the drives, and I know I did not set any RAID levels other than RAID0. Anyone have any ideas how I can kill this and get back to just two independent IDE drives? Or can anyone convince me of a reason to go the AHCI route? Many thanks in advance.

  Read the article

• Home media storage solution

  - by Dan

  I record lots of personal HD film footage and am looking for a cheap way to store all of this. I take ~120 GB of footage each month, so something expandable would be nice... something that might be able to hold 6+ SATA drives. There is a low load requirement, as there is never more than a user or two... but it should be able to keep up with streaming 2 simultanious HD videos. I don't really want to spend more than $200-$300 on top of the $900 I am thinking of spending for 6X2GB SATA drives@ $150 apiece, but I am willing to pay extra for a quality solution. Should I get a cheap NAS server? a cheap multi-drive external enclosure? should I just get some used systems off craigslist? If it is an independent system I'll probably just throw ubuntu on it since I can maintain that well. Its easy to do a software raid from ubuntu too, if I choose to go that way. Thanks

  Read the article

• Running a VM off a USB 2.0 Flash Drive - Mac/Parallels/XP

  - by geerlingguy

  I use a MacBook Air as my primary machine, and the 128GB SSD means space is precious. To save about 10 GB, I've been running Parallels with a Windows XP VM off an external USB hard drive, which performs as well in everyday use as running the VM off the internal SSD. So, I bought a tiny 32GB USB 2.0 flash drive, plugged it into the MacBook Air, formatted it first as ExFAT (which was slow), then as Mac OS Extended (Journaled) (which was also slow), and copied over my VM file, and ran Parallels off it. My full experience is documented here: http://www.midwesternmac.com/blogs/jeff-geerling/running-windows-xp-vm Straight file copies are really fast — 30 MB/sec read (solid the whole time), and 10-11 MB/sec write (solid the whole time). But I noticed that once XP started running, the disk access rates were in the low KB ranges. Are USB flash drives really that poor at random access, or could I possibly be missing something (the format of the flash drive, etc.?)? Of note, I've tried the following, to no great effect: Formatting the drive as either ExFAT or Mac OS Extended (Journaled) Unplugging all other USB devices and turning off Bluetooth (which runs on the right-side-port USB bus). Plugging in the flash drive either direct in the right side port, or the left side port, or into a USB 2.0 hub

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• LDAP authentication issue with Kerio Connect

  - by djk

  Hi, We have Kerio Connect (mail server) running on a Windows Server 2003 server on a domain. In the webmail client, users are able to change their domain password. This functionality used to work fine until a user tried to change their password a few days ago, when every password they'd try would result in the webmail client claiming their password was "invalid". I spoke to Kerio about this and they claim that this error is returned by the domain controller, which supports my initial investigations. The error that the DC is logging when an attempt is made to change the password is this: "80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 52e, vece" The "data 52e" part indicates that this is an "invalid credentials" error. I don't see how this can be as I've tried (in the Kerio Connect configuration) various accounts that have privileges to modify accounts, including my own as I am a domain admin. I have ran 'dcdiag' (all tests) on the DC and it came back passing every single one of them. I've searched high and low for an answer to this and came up empty. Does anyone have any idea why this may have suddenly started happening? Thanks! Edit: I should mention that the passwords we are changing to do comply with the complexity policy.

  Read the article

• Choosing a new laptop

  - by chiongms

  I'm looking for a new laptop. I saw few: i) HP ProBook 4321s ii) HP ProBook 6440b iii)Dell Latitude E6410 i found these laptops are still very new..is it? not much comments about them. can anyone help? i doubt how their graphic cards perform compare to each other? ProBook 4321s- Radeon HD4350 ProBook 6440b- Radeon HD4550 Latitude E6410- NVS 3100M most of the time i'll running 3D CAD software, C++ programing...i saw my friend's laptop with radeon HD4350. it's perfectly fulfilling my demand. but i wonder how the other two are? Another thing i doubt is the screen resolution..my current laptop is 1280x800, and i found it comfortable to use. But these two HP only offer 1366x768..will it make any large different? Lastly, is there anyway to estimate how their power consumption is from the spec sheet? well, i would prefer one with longer battery usage time. my current laptop is suck...only last 1 hour even when it's still new..i'm not going to get another like this anymore. Anyone can help me please? Thanks!

  Read the article

• Spots appear in a rectangle area on screen, ubuntu gnome 13.04, nvidia driver

  - by frozen-flame

  I am using Ubuntu Gnome 13.04 with nvidia-310 driver installed. My GPU is GeForce GTX650. Strange spots freqently appear on screen, with following traits: Spots are restricted in one or two rectangle areas at any instant. When typing, the pattern of spots change. Possibly increase, or all disappear when one key pressed. Mouse movement also influences. This problem last within one boot. The only way can I get rid of this problem is to reboot. It can be detected as soon as entering desktop if it appears. Simultaneously, the "power off" option is lost in the top-right menu of Gnome3. Never such problem when using windows 7 on the same computer, neither ubuntu with Nouveou driver. Seldomly, half of the screen become black. I googled a lot. Similar conditions are described, but no confirmed solution. Uninstall-r einstall strategy does not work. Any clue solving this will be appeciated.

  Read the article

• ASP.NET sending email through exchange problem

  - by Solmead

  I have an exchange 2010 server running on Windows 2008 R2, I also have a remote webserver running Windows 2003 with multiple sites on it (all asp.net mvc 2 sites). I setup a Transport in exchange and all the websites on my remote web server can send email no problem to anyone in the exchange server and to any external domain. Now for my problem. I am having issues with that webserver, so I moved one of the websites to run on my exchange server, it runs well (low hit website) except that email doesn't work from that site. I tried changing the Transport in exchange to add the IP address of the local machine and the 127.0.0.1 addresses and it still isn't sending any email. Any ideas on how to get this working? The remote websites can still send email no problem, the version of the site that I had to move on the remote server can still email, but on the exchange server for that website email does not send. I would guess it is a Transport issue, since it is running on the same server a firewall shouldn't be the issue. I changed the smtp setting in web.config to localhost, and now I do receive email to my account on the exchange server, but I do not receive any emails on outside addresses. To add more description, this is a custom developed asp.net mvc 2 website. And no errors were being generated in the code when sending the email in either case.

  Read the article

• changing filesystem format from xfs to ext4 without losing data

  - by A.Rashad

  I have a fresh Lucid Lynx (Ubuntu 10.04) running on a laptop. where I defined the filesystems as: mount point / on ext4 (46 Gb) mount point /home on jfs (63 GB) swap as 3 Gb I left the machine over night to do some task, without AC power supply. next day in the morning I found it on standby, task completed, but filesystem was not reachable. it gave me I/O error it seems that there is a problem with jfs and standby. anyways, to avoid any hassle, I want to move this mount point from jfs format to ext4. can I do this without losing data and without the need to place the data in a temporary location until transformation is done? sorry to mention that, but I recall back in the windows days, we would change a FAT16 to FAT32 or a FAT32 to NTFS without having to lose the data. I hope this is available on Linux. Update The /home filesystem was xfs not jfs, and it seems there is a bug with this filesystem for some reason, I had to re-install the OS twice until I ended up with ext4 for the entire / However, as a conclusion, it seems that there is no way to make a conversion

  Read the article

• Apahe configuration with virtual hosts and SSL on a local network

  - by Petah

  I'm trying to setup my local Apache configuration like so: http://localhost/ should serve ~/ http://development.somedomain.co.nz/ should serve ~/sites/development.somedomain.co.nz/ https://development.assldomain.co.nz/ should serve ~/sites/development.assldomain.co.nz/ I only want to allow connections from our local network (192.168.1.* range) and myself (127.0.0.1). I have setup my hosts file with: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 development.somedomain.co.nz 127.0.0.1 development.assldomain.co.nz 127.0.0.1 development.anunuseddomain.co.nz My Apache configuration looks like: Listen 80 NameVirtualHost *:80 <VirtualHost development.somedomain.co.nz:80> ServerName development.somedomain.co.nz DocumentRoot "~/sites/development.somedomain.co.nz" DirectoryIndex index.php <Directory ~/sites/development.somedomain.co.nz> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost localhost:80> DocumentRoot "~/" ServerName localhost <Directory "~/"> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <IfModule mod_ssl.c> Listen *:443 NameVirtualHost *:443 AcceptMutex flock <VirtualHost development.assldomain.co.nz:443> ServerName development.assldomain.co.nz DocumentRoot "~/sites/development.assldomain.co.nz" DirectoryIndex index.php SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /Applications/XAMPP/etc/ssl.crt/server.crt SSLCertificateKeyFile /Applications/XAMPP/etc/ssl.key/server.key BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 <Directory ~/sites/development.assldomain.co.nz> SSLRequireSSL Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> </IfModule> http://development.somedomain.co.nz/ http://localhost/ and https://development.assldomain.co.nz/ work fine. The problem is when I request http://development.anunuseddomain.co.nz/ or http://development.assldomain.co.nz/ it responds with the same as http://development.somedomain.co.nz/ I want it to deny all requests that do not match a virtual host server name and all requests to a https host that are requested with http PS I'm running XAMPP on Mac OS X 10.5.8

  Read the article

• How can Standard User change file associations in Windows 2000?

  - by Gary M. Mugford

  One of my clients is still running Win2K server with a host of Win2K workstations. And no net admin, due to the downturn of the economy over the years. I'm sort of helping out. Out of my depth, but I am a loyal foot soldier. A problem I encounter rather too often is a user double-clicks on a file in Explorer and then either gets no action, or the wrong program to run. It's a case of a missing or out-of-date file association. The current cure is to temporarily upgrade the user from Standard to Power, do the FA switch and then change back. As Winnie would whine, 'Oh, bother!' At any rate, I thought I'd ask here. Is there a method/program to run without the rigamarole FROM the Standard Users account on the workstation to edit/add a file association? I assume the program route would involve RunAs. I 'believe' most of the workstations run the RunAs service, but I could be wrong. I understand that's required, if there is to be a solution. Any help accepted with thanks. GM NOTE: Seems wassociate from http://www.xs4all.nl/~wstudios/Associate/index.html can resolve the issue.

  Read the article

• How can Standard User change file associations in Windows 2000?

  - by Gary M. Mugford

  One of my clients is still running Win2K server with a host of Win2K workstations. And no net admin, due to the downturn of the economy over the years. I'm sort of helping out. Out of my depth, but I am a loyal foot soldier. A problem I encounter rather too often is a user double-clicks on a file in Explorer and then either gets no action, or the wrong program to run. It's a case of a missing or out-of-date file association. The current cure is to temporarily upgrade the user from Standard to Power, do the FA switch and then change back. As Winnie would whine, 'Oh, bother!' At any rate, I thought I'd ask here. Is there a method/program to run without the rigamarole FROM the Standard Users account on the workstation to edit/add a file association? I assume the program route would involve RunAs. I 'believe' most of the workstations run the RunAs service, but I could be wrong. I understand that's required, if there is to be a solution. Any help accepted with thanks. GM NOTE: Seems wassociate from http://www.xs4all.nl/~wstudios/Associate/index.html can resolve the issue.

  Read the article

• Identifying Hard Drive as performance bottleneck for desktop machines

  - by Programming Hero

  I'm working in a development team where we all use laptops so we can work in multiple locations. These laptops are proving notoriously slow for development work, but at a glance they all look to have the specification for a much faster experience: CPU - Intel Core 2 Duo T7500 Memory - 2GB of RAM We all experience the biggest delays when the hard-drives are being accessed, particularly when swap-files are being thrashed. After doing a little bit of profile, a colleague discovered that our HDDs are seeing Read/Write speeds of about 10MB/sec. This seems abnormally low and we believe it the cause of the problem. Sensibly (though somewhat annoyingly) our business wont blow money on faster drives just to see if it fixes the problem; we need to illustrate this is definitely the problem and that buying some solid-state drives will make it go away. I need some way of showing how 90% of the system resources aren't being used over the course of a day, and that whenever there is utilization, it's all in HDD reads or writes. Are there any tools I could use to provide this information? Does it seem likely the problem is going to be fixed by a faster drive? Should I be looking for alternatives?

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• Microsoft Arc Mouse OS X

  - by meepz

  I recently bought a new Mac Book Pro with Mountain Lion 10.8 on it. The only portable mouse I have is my Microsoft Arc Mouse. I wanted to use it with the laptop so I installed the IntelliPoint 8.2 for Mac from Microsofts website. According to their website, this driver is for OS X 10.4-10.7. Now I thought that wouldnt be too much of an issue but unfortunately for me, the driver installs fine and the mouse is detected but I get no movement and when I click the buttons nothing happens. I took the mouse with me on a business trip to EU and before I left I checked if the mouse worked with my desktop which is running Windows 7 and it worked without any hiccups. I'm not too sure where the OS differs from 10.7 to 10.8. I found an article online but it doesn't pertain to my mouse, although it could be of assistance. I have tried my version of their adjustment but I am not too knowledgable on low level hardware/software modifications so I may have done it wrong. heres the link: http://refluxions.wordpress.com/2008/08/18/mac-os-x-mouse-madnessfixed/ I get the following details when I check mouse info in the IntelliPoint preferences pane: The following Microsoft mouse devices are currently connected to your Macintosh driven by the Intellipoint software. Arc Mouse Vendor name: Microsoft Product name: Microsoft AE 2.4GHz Transceiver 5.0 Vendor ID: 045E Product ID: 074F Device version: 0140 if anyone has any suggestions on how to fix this it would be greatly appreciated! I love the mouse and im here in EU for another two weeks. Thanks

  Read the article

• Enable CPU fan always on

  - by Gundars Meness

  I am using 3 years old overheating laptop and I want my CPU fan to be spinning 24/7 regardless of the consequences. How to make it spin? The problem is that CPU & GPU heats up to 68°C (154 F) right after boot and never goes down, because CPU fan is not spinning full throttle. It starts spinning faster when temperature goes over 70°C and stops when it reaches seventy again. When doing heavy work on databases, it gets from 70 to 90 in no-time and automatically powers off. Bios does not contain any "fan spin 100%" options, just "spin slowly all the time" and "auto" which is more useless than the first one since my fan doesn't have pwm wire. Currently I'm solving this with cooling stand (3x5V), but it isn't much of a help. I would rather use the CPU fan since it is the only fan directly responsible for cooling down CPU/GPU. But how to make it spin 100% all the time? Should I attach it's red power wire to motherboard to get constant 5V (is there such option?), or is there an option to control it via software? Laptop: Samsung R528 2.3 GHz Intel i3 with Nvidia GeForce 310M Bios: Phoenix 03KT.M003.20100622.KSJ (and that is latest update) OS: Ubuntu 12.04.2 LTS with 3.2.0.51 kernel CPU fan: Image/Description Has 5V 0,4A and only 3 pins, no pwm. P.S. Yes, I did clean everything with alcohol, freed the air vents, changed thermal paste etc; that reduced temperature by 4 degrees.

  Read the article

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• Warning for "Reallocated Event Count" S.M.A.R.T. attribute with a new/unused drive. How serious is t

  - by Developer Art

  I've just looked at the health status of my old 2,5 inch 500 Gb Fujitsu drive with a popular "HD Tune" utility. It shows a warning for the "Reallocated Event Count" property. How serious is that? The thing is that the drive is practically new. I pulled it out of a new laptop over a year ago and never used it since. Right now it only has 53 "Power On" hours which sounds about right since I only had it running a few evenings overnight before switching it for something more performant. Does this warning indicate that the drive is likely to fail some time in the future? I'm somewhat perplexed since the drive is effectively unused. What is more, I have arranged with somebody to buy off this drive since I don't really need. It is 12,5 mm thick (with 3 plates) meaning it doesn't fit into an external enclosure which makes it quite useless to me. Can I give away the drive without having it on my conscience or better cancel the deal? In other words, can the drive be used safely for years to come or better throw it away? I'm running a sector test now to see if there are any real problems. Will post the results as soon as they're available.

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

• Hyper-V Virtual Machine won't respond over network

  - by Brad Gignac

  Recently, one of our Hyper-V virtual machines has periodically stopped responding over the network. It seems to be happening every few days, and it occasionally happens up to several times a day. I am by no means a sysadmin, so any direction you guys could provide would be very welcome. I've included everything I know to include below. If you need any additional information, I'll be glad to include it. I can connect through the Hyper-V console. I can't connect to network shares, IIS web apps, using RDP, or using ping. Memory usage seems to be normal (3 of 4 GB) Processor usage seems low. We don't know the exact time the server goes down, but the following error appears consistently around the time it goes down: Error 5719, NETLOGON This computer was not able to set up as secure session with a domain controller in domain *** due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If this problem persists, please contact your domain administrator.

  Read the article

• a disk read error occurred

  - by kellogs

  Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

  Read the article

• vmdk Recovery after migration from 3.5 to 4 and fallback tentative.

  - by olgirard

  Hy, I've tryed to migrate some VM from my 3.5i environment to a brand new vSphere 4.0 U1. The two platforms are running simultaneously, sharing the same SAN. I Migrate my VM by stopping it, unregistering in vcenter (esx ver. 3.5, i call it esx3), register in vSphere (esx ver. 4, i call it esx4), and migrate upgrade virtual hardware before powering it up (First mistake). vMotion was enabled on esx4, seem to be a second mistake. After a day or so, i encountred problems joigning the esx server (esx4) and decided to unregister my server for esx4 and fallback to esx3. esx3 refused to boot, i supposed this was due to virtual hardware in Version 7 so i recreated a new VM pointing to the vmdk of the old VM. Everithing seemed fine until i log into the server and discover that i was running on the original disk ith every snapshots ignored even those created on esx3. I tried to reboot VM on esx4 but VM doesn't power up because "The parent virtual disk has been modified since the child was created". I've got a copy of a later state of the drive but generated between two snapshots (ovf generated with canverter standalone) as a backup. Do i have a chance to recover at least some files on the virtual drive or (as i tink) all is played, i've done enought mistakes for this time. Thanks for your help.

  Read the article

• Shared firewall or multiple client specific firewalls?

  - by Tauren

  I'm trying to determine if I can use a single firewall for my entire network, including customer servers, or if each customer should have their own firewall. I've found that many hosting companies require each client with a cluster of servers to have their own firewall. If you need a web node and a database node, you also have to get a firewall, and pay another monthly fee for it. I have colo space with several KVM virtualization servers hosting VPS services to many different customers. Each KVM host is running a software iptables firewall that only allows specific ports to be accessed on each VPS. I can control which ports any given VPS has open, allowing a web VPS to be accessed from anywhere on ports 80 and 443, but blocking a database VPS completely to the outside and only allowing a certain other VPS to access it. The configuration works well for my current needs. Note that there is not a hardware firewall protecting the virtualization hosts in place at this time. However, the KVM hosts only have port 22 open, are running nothing except KVM and SSH, and even port 22 cannot be accessed except for inside the netblock. I'm looking at possibly rethinking my network now that I have a client who needs to transition from a single VPS onto two dedicated servers (one web and one DB). A different customer already has a single dedicated server that is not behind any firewall except iptables running on the system. Should I require that each dedicated server customer have their own dedicated firewall? Or can I utilize a single network-wide firewall for multiple customer clusters? I'm familiar with iptables, and am currently thinking I'll use it for any firewalls/routers that I need. But I don't necessarily want to use up 1U of space in my rack for each firewall, nor the power consumption each firewall server will take. So I'm considering a hardware firewall. Any suggestions on what is a good approach?

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >