Search Results

Search found 9730 results on 390 pages for 'restart programs'.

Page 300/390 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• KVM work with bridge network problems

  - by isware

  I try to configure bridge network for KVM(refer to http://www.linux-kvm.org/page/Networking), and it worked for Guest OS, but I have two problems with my Fedora host OS: 1?I can not access internet on host 2?The bridge configuration lost after reboot, I need to execute "service network restart" again to bring it up I checked here(http://serverfault.com/questions/168119/kvm-network-bridge-with-public-static-ip-for-both-host-and-guests) for the first problem, it seems not working for me. Any advice is appreciated! ifconfig -a eth0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:231340 errors:0 dropped:0 overruns:0 frame:0 TX packets:413424 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:15335606 (14.6 MiB) TX bytes:114755796 (109.4 MiB) Interrupt:44 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:119307 errors:0 dropped:0 overruns:0 frame:0 TX packets:119307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:57151264 (54.5 MiB) TX bytes:57151264 (54.5 MiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) sw0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet addr:192.168.1.133 Bcast:255.255.255.255 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:229584 errors:0 dropped:0 overruns:0 frame:0 TX packets:401232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11047463 (10.5 MiB) TX bytes:113891533 (108.6 MiB) tap0 Link encap:Ethernet HWaddr F2:86:1A:48:E2:55 inet6 addr: fe80::f086:1aff:fe48:e255/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232 errors:0 dropped:0 overruns:0 frame:0 TX packets:2744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:24842 (24.2 KiB) TX bytes:243899 (238.1 KiB) virbr0 Link encap:Ethernet HWaddr 9A:7C:09:6B:85:65 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:46 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5513 (5.3 KiB)

  Read the article

• Windows Update Agent Update Failed

  - by Adrian Godong

  I'm trying to install the latest version of Windows Update Agent, v7.2.6001.788, and the installation failed with error code of 0x800b0100. Running Windows Server 2008 SP1. The relevant WindowsUpdate.log section: 2009-08-03 16:17:49:334 3544 d28 Misc =========== Logging initialized (build: 7.2.6001.788, tz: +0100) =========== 2009-08-03 16:17:49:334 3544 d28 Misc = Process: d:\fcc0f96e893296900e6501a601\wusetup.exe 2009-08-03 16:17:49:332 3544 d28 Setup Windows Update Client standalone setup : resource dll path is d:\fcc0f96e893296900e6501a601\en\wusetup.exe.mui 2009-08-03 16:17:49:335 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:49:556 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:556 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-ActiveX.cab" 2009-08-03 16:17:49:580 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:580 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Aux-TopLevel.cab" 2009-08-03 16:17:49:665 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:709 3544 d28 Setup Windows Update Client standalone setup : eula file path is d:\fcc0f96e893296900e6501a601\en\eula.rtf 2009-08-03 16:17:52:337 3544 de0 Misc WARNING: LoadLibrary failed for srclient.dll with hr:8007007E 2009-08-03 16:17:52:338 3544 de0 Setup Installing CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:53:895 3544 de0 Setup WARNING: CBS operation failed, error = 0x800B0100 2009-08-03 16:17:53:898 3544 de0 Setup WARNING: Install of setup package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" failed, error = 0x800B0100 2009-08-03 16:18:04:976 3544 d28 Setup wusetup has finished. Exit code is 0. Reboot is NOT needed I think something went wrong twhen loading the srclient.dll. Things that I have done and still no fix: msiexec /unregister and msiexec /register regsvr32 wuapi.dll Run CheckSUR tool and restart

  Read the article

• compose-key mappings differ between gtk and qt apps

  - by intuited

  I'm noticing that there is an inconsistency in the output of one of the compose-key combos. When I type ( [Compose] . . ) under Chrome, gedit, gnome-terminal, or roxterm I get the character '?'. This is a small raised dot: $ echo -n '?' | xxd 0000000: cb99 .. When I type the same combo under konsole, yakuake, or kate, I get the character '…'. This is an ellipsis: $ echo -n '…' | xxd 0000000: e280 a6 ... This is not a font issue: if I copy-paste the characters from an app using one toolkit to an app using the other, its appearance is maintained. I use a few other combos pretty regularly and they seem to work consistently across toolkits. I think this is a pretty recent phenomenon. I upgraded from Ubuntu 8.10 to 9.10 fairly recently so this might be related. I'm not sure if this will reoccur if I restart X, and I'd rather not find out. Can someone explain how this is possible, and what I can do to resolve it? I'd like to have the ellipsis appear in all apps when that combo is entered.

  Read the article

• Commandline program to extract archives with automatic subdirectry detection

  - by ??????

  The title already says it. What I'm looking for is essentially the pure commandline counterpart to ark -ba <path> (on KDE), or file-roller -h <path> (on GNOME/Unity). Unfortunately, both ark and file-roller require X to be running. I'm aware that it is relatively simple to write a tool that detects archives based on their file extension, and then runs the appropiate program: #!/bin/bash if [[ -f "$1" ]] ; then case $1 in *.tar.bz2) tar xjvf $1 ;; *.tar.gz) tar xzvf $1 ;; *.bz2) bunzip2 $1 ;; *.rar) rar x $1 ;; *.gz) gunzip $1 ;; *.tar) tar xf $1 ;; *.tbz2) tar xjvf $1 ;; *.tgz) tar xzvf $1 ;; *.zip) unzip $1 ;; *.Z) uncompress $1 ;; *.7z) 7z x $1 ;; *) echo "'$1' cannot be extracted with this utility" ;; esac else echo "path '$1' does not exist or is not a file" fi However, that doesn't take care of subdirectory detection (and in fact, many extraction programs do not even supply such an option). So might there be a program that does exactly that? I wasn't sure whether or not to ask on askubuntu.com, because this question isn't really about Ubuntu, but rather about any Linux operating system. My apologies if this question does not fit in here.

  Read the article

• "A disk read error occurred" when booting XP disk image in VirtualBox

  - by intuited

  I'm trying to boot an XP installation cloned into VirtualBox from a real drive. I'm getting the message A disk read error occurred Press Ctrl+Alt+Del to restart whenever* I try to boot the machine. * This is not strictly true: with AMD-V enabled, the boot process appears to not make it this far and instead hangs at a black screen with cursor. I created the VirtualBox image from the original drive using the following method: $ sudo ddrescue -n /dev/sdd sdd.img logfile # completed without errors $ VBoxManage convertfromraw sdd.img disk.vdi The original disk (and the image) contain a single NTFS partition with XP installed on it. The owner of the drive indicates that it did boot okay the last time the system made it that far. The (Pentium 4) system has a broken (enormous) heat sink, so at some point it failed to boot because it would quickly overheat and shut down. If I boot the VM from a live cd, I am able to mount its /dev/sda1 without any problems. I ran ntfsfix and didn't have any luck. I've read through the instructions on doing this. I didn't really follow them. For example, I didn't run MergeIDE before imaging because the machine was not bootable. However, the symptom of that problem seems to be quite different. The emitted message is contained in the volume boot record of the XP partition, which leads me to suspect that this is a problem with the core operating system bootstrap procedure, and not related to anything in the registry. I don't have an XP boot CD.

  Read the article

• WHS - Windows Update Failure

  - by Kyle B.

  Clicking "Update Now..." inside my EX470 control panel for Windows Update produces the following error message: "Windows Home Server updates installation can not complete. Please try again later. If the problem persists, please restart the server." I have rebooted the server numerous times, and I have also used remote desktop to connect to the machine to perform the update this way, however the browser is unable to pull up http://windowsupdate.microsoft.com. This is very strange behavior because I am able to access all other sites (gmail.com, serverfault.com, etc). Would it be possible for someone to explain to me how I can check to see what is blocking the connection of this device, which apparently has a valid internet connection, to the Microsoft Windows Update site? note #1 Using the shortcut: %SystemRoot%\system32\wupdmgr.exe does not work either. It says "Connecting to 65.55.200.155..." but nothing ever happens. This is strange because all other sites seem fine. Also, I can connect to windowsupdate.microsoft.com on my local desktop so I know this is running as well

  Read the article

• OCZ Vertex 3 SSD boot failure

  - by Col Zero

  Ok, so I just purchased and received a 120GB OCZ Vertex 3. I had Windows 7 on an .ISO file on my computer. I formatted a USB stick and configured it to be read as a CD so that I could install windows onto my SSD from it. I started my comp, had the boot priority set to my USB, starting installing windows 7 to my SSD. And out of no where (I wasn't watching) my computer restarted and it brought me back to the beginning of the Windows 7 set-up. So I turned my computer off and booted it up from the SSD to see if it had installed onto the SSD. The first 2 attempts I had a disk boot failure. So I plugged my hard drive back in, started my computer, turned it off, plugged the SSD back in (literally) and it booted up fine/ Finalized windows got internet set up, and Windows had updates that required a restart. So I restarted and had another disk boot failure. Now I have a disk boot failure every time I try to start my computer up through my SSD. Extra Info: My SSD has never been able to be detected in my BIOS unless my Hard Drive was unplugged (eve then my BIOS didn't always detect it). MY SSD wasn't detected in my BIOS the first and only time it successfully booted up. My SSD literally boots up successfully randomly (only once unfortunately) and is detected in my BIOS randomly. I've tried switching cords etc and nothing has worked. I just want to get this damn thing running so I can see whats its like. I finally found a way to get the OS on this sucker and now it won't even boot up. Any help appreciated

  Read the article

• Resolving "JBoss Web Console is Accessible to Unauthenticated Remote Users" vulnerability

  - by IAmJeff

  Our security team has determined there is a vulnerability in one of our systems. We are using version JBoss 5.1.0GA on RHEL 5.10. Vulnerability description: JBoss Web Console is Accessible to Unauthenticated Remote Users Yes, this looks familiar. Refer to Question 501417. I do not find the answer there complete. Can someone (or multiple someones) answer Does a newer version of JBoss fix this vulnerability? Are there links describing, in more detail, manual modification of JBoss configuration files to resolve the issue? Are there others options to remediate this vulnerability? Why don't I find the other answer complete? I'm not at all familiar with JBoss, so this answer seems a bit too simple. The web-console.war contains commented-out templates for basic security in its WEB-INF/web.xml as well as commented-out setup for a security domain in WEB-INF/jboss-web.xml. Just uncomment those basic security blocks and restart? Is there anything else I need to include? This seems generic. Do I need to include anything about my environment, such as absolute paths, etc.? Am I making this too complicated?

  Read the article

• How to completely disable laptop sound?

  - by Alvaro Rodriguez

  I have a HP Pavillion DV7 laptop with win 8 pro. The laptop has an unidentified problem with sound drivers or hardware that sometimes causes volume to constantly jiggle up and down. This is very annoying because of these consequences: Renders mute unusable - as the volume changes the sound unmutes automatically Causes an annoying win 8 "surface UI" notification to appear constantly in the upper left corner, which is distracting enough by itself, but more importantly Renders the whole "surface UI" unusable, because it loses focus whenever the sound changing notification appears When the jiggling happens, the laptop also loses the ability to redirect sound to earphones - sound comes out of the speakers even if earphones are connected. To solve these issues I want to completely disable sound in the laptop (I've tried reinstalling drivers several times to no end). I have tried disabling all sound related drivers and devices in the Device Manager but Windows re-enables those automatically whenever I restart the laptop. The BIOS doesn't have any settings to disable sound hardware either. Please don't suggest having the laptop sound serviced or fixed. It's not worth the expense. I just want to remove sound support so I can use it normally. It is very unusable as it is now.

  Read the article

• MS SQL Server slows down over time?

  - by Dave Holland

  Have any of you experienced the following, and have you found a solution: A large part of our website's back-end is MS SQL Server 2005. Every week or two weeks the site begins running slower - and I see queries taking longer and longer to complete in SQL. I have a query that I like to use: USE master select text,wait_time,blocking_session_id AS "Block", percent_complete, * from sys.dm_exec_requests CROSS APPLY sys.dm_exec_sql_text(sql_handle) AS s2 order by start_time asc Which is fairly useful... it gives a snapshot of everything that's running right at that moment against your SQL server. What's nice is that even if your CPU is pegged at 100% for some reason and Activity Monitor is refusing to load (I'm sure some of you have been there) this query still returns and you can see what query is killing your DB. When I run this, or Activity Monitor during the times that SQL has begun to slow down I don't see any specific queries causing the issue - they are ALL running slower across the board. If I restart the MS SQL Service then everything is fine, it speeds right up - for a week or two until it happens again. Nothing that I can think of has changed, but this just started a few months ago... Ideas? --Added Please note that when this database slowdown happens it doesn't matter if we are getting 100K page views an hour (busier time of day) or 10K page views an hour (slow time) the queries all take a longer time to complete than normal. The server isn't really under stress - the CPU isn't high, the disk usage doesn't seem to be out of control... it feels like index fragmentation or something of the sort but that doesn't seem to be the case. As far as pasting results of the query I pasted above I really can't do that. The Query above lists the login of the user performing the task, the entire query, etc etc.. and I'd really not like to hand out the names of my databases, tables, columns and the logins online :)... I can tell you that the queries running at that time are normal, standard queries for our site that run all the time, nothing out of the norm.

  Read the article

• localhost won't load after adding config data to httpd

  - by OldWest

  I am not very experienced with configuring httpd, and I am following a tutorial to view my site w/ domain name under localhost. My localhost just blanks out and my apache services won't restart. I checked all of my paths and they are correct. I am editing the w*indows/system32/drivers/etc/host*s file and my apache httpd file. This is what I am putting in my hosts file: 127.0.0.1 www.cars_v1.0.com.localhost And in the footer of my httpd file I am putting this: <VirtualHost 127.0.0.1:80> ServerName www.cars_v1.0.com.localhost DocumentRoot "C:\wamp\www\symfony\cars_v1.0\web" DirectoryIndex index.php <Directory "C:\wamp\www\symfony\cars_v1.0\web"> AllowOverride All Allow from All </Directory> Alias /sf C:\wamp\www\symfony\cars_v1.0\lib\vendor\symfony-1.4.8\data\web\sf <Directory "C:\wamp\www\symfony\cars_v1.0\lib\vendor\symfony-1.4.8\data\web\sf"> AllowOverride All Allow from All </Directory> </VirtualHost>

  Read the article

• NRPE unable to read output, but why?

  - by ticktockhouse

  I have this problem with NRPE, all the stuff I've found so far on the net seems to point me at things I've already tried. # /usr/local/nagios/plugins/check_nrpe -H nrpeclient gives NRPE v2.12 as expected. Running the command by hand (as defined in nrpe.cfg on "nrpeclient", gives the expected response nrpe.cfg: command[check_openmanage]=/usr/lib/nagios/plugins/additional/check_openmanage -s -e -b ctrl_driver=0 bat_charge "Expected response" But if I try to run the command from the Nagios server I get the following: # /usr/local/nagios/plugins/check_nrpe -H comxps -c check_openmanage NRPE: Unable to read output Can anyone think of anywhere else I might have made a mistake with this? I've done the same thing on multiple other servers with no problem. The only difference I can think of with this is that this box is RHEL 5 based, whereas the others are RHEL 4 based. Those two bits above that I've tested are the what most people seem to suggest when people have had this problem. I should mention that I get a weird error in the logs when I restart nrpe: nrpe[14534]: Unable to open config file '/usr/local/nagios/etc/nrpe.cfg' for reading nrpe[14534]: Continuing with errors... nrpe[14535]: Starting up daemon nrpe[14535]: Warning: Daemon is configured to accept command arguments from clients! nrpe[14535]: Listening for connections on port 5666 nrpe[14535]: Allowing connections from: bodbck,combck,nam-bck Even though, it's plainly reading that /usr/local/nagios/etc/nrpe.cfg file to get the stuff it's talking about further down..

  Read the article

• Remote Sending of Emails via SMTP/EXIM Issue

  - by Christian Noel

  I have been encountering a problem when sending messages via EXIM. Here is the scenario: I have 2 servers lets just say host1.com = where all my apps and programs are hosted. host2.com = is another server which handles some apps but is also my smtp mail server. whm and cpanel are installed in both hosts as well as exim. right now, messages are being sent out as [email protected] to clients. host1.com uses the [email protected] so that it can send messages outbound as well. here's the problem, after a few hours from a fresh reboot of host1.com, sending messages from host1.com is no longer possible because i encounter an error that states: system/vendor/swift/Swift/Connection/SMTP.php [309]: The SMTP connection failed to start [tls://mail.host2.com]: fsockopen returned Error Number 110 and Error String 'Connection timed out'` also note that this was working fine earlier (like 10 hours ago) but then it suddenly fails. everytime i restart the host1.com then sending messages will work again. i have checked logs and traces but to no avail the only means of fixing this problem is restarting host1.com.

  Read the article

• Swap space maxing out - JVM dying

  - by travega

  I have a server running 3 WordPress instances, MySql, Apache and the play framework 2.0 on 64m initial & max heap. If I increase the max heap of the JVM that play is running in even by 16m I see the 128m of swap space steadily fill up until the the JVM dies. I notice that it is only when I am plugging away at the wordpress sites that the JVM will die. I assume this is because the JVM is not asking for memory at the time so gets collected. I notice that when I restart Apache I reclaim about half of my swap and RAM. So is there some way I can configure apache to consume less memory? Also what could be causing the swap space to get so heavily thrashed with just 16m added to the max heap size of the JVM? Server running: Ubuntu 12.04 RAM: 408m Swap: 128m Apache mods: alias.conf alias.load auth_basic.load authn_file.load authz_default.load authz_groupfile.load authz_host.load authz_user.load autoindex.conf autoindex.load cgi.load deflate.conf deflate.load dir.conf dir.load env.load mime.conf mime.load negotiation.conf negotiation.load php5.conf php5.load proxy_ajp.load proxy_balancer.conf proxy_balancer.load proxy.conf proxy_connect.load proxy_ftp.conf proxy_ftp.load proxy_http.load proxy.load reqtimeout.conf reqtimeout.load rewrite.load setenvif.conf setenvif.load status.conf status.load

  Read the article

• Problem running mysql client, cannot connect to mysql server

  - by ehsanul

  Edit3: Thanks for the help everyone. Sorry for wasting anybody's time, but it seems like a simple reboot solved it. I should've known better, but I just had the assumption that the "restart" solution is mostly valid just for MS Windows (no offense). I'll keep this in mind before I ask a question here again. I installed the mysql-client-5.0 and mysql-server-5.0 packages on Ubuntu 8.04, using sudo apt-get install. When I try to run the "mysql" command, I get the following error: ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) To verify that mysql server is running, I tried this, and it does seem to be running, with the correct socket too: $ ps aux | grep mysql root 13388 0.0 0.0 1772 528 ? S 06:24 0:00 /bin/sh /usr/bin/mysqld_safe mysql 13553 0.0 1.4 127012 15332 ? Sl 06:25 0:00 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --port=3306 --socket=/var/run/mysqld/mysqld.sock root 13555 0.0 0.0 3008 696 ? S 06:25 0:00 logger -p daemon.err -t mysqld_safe -i -t mysqld ehsanul 16910 0.0 0.0 3092 772 pts/4 R+ 07:17 0:00 grep mysql So I don't understand why I'm getting an error trying to connect to mysql server. Note that I'm completely new to mysql. Edit: As requested in comments, the exact command that is returning the error is simply "sudo mysql". And when I check netstats for active networks services, I do see an entry for port 3306, with Protocol: tcp, IP Source: 127.0.0.1, State: LISTEN Edit2: It appears as if the /var/run/mysqld/mysqld.sock socket doesn't exist (if I'm interpreting the following output correctly): $ ls -al /var/run/mysqld/ total 0 drwxr-xr-x 2 mysql root 40 2009-08-06 06:36 . drwxr-xr-x 20 root root 860 2009-08-06 06:25 ..

  Read the article

• Ati X1600 driver problem on Mac

  - by Mulot

  Hi all, I currently own a 06' Macbook pro 1.1, and since some months I have recurrent problems of displays bug or artifacts. I searched quickly around to see that a lot of other users on Mac (iMac or Macbook pro) also have the same problem due to a problem for the X1600 video card. Apparently it's due to overheating problem, in my case even without warming a lot I have very bad display bugs such as colorful pixel lines, or glitches, and freeze and crash, all of this on Tiger, Leopard and Snow Leopard. I found this interesting article here talking about this problem and trying to gather people so that Apple take the serious GPU problem in consideration. In one of the comments, an user said he removed all bundle named with "radeon" and then he had no more problems under Leopard, and seems ot work fine well too on Snow Leopard. I did the same thing, I removed the bundles of the driver, restart, and no more problems, but not more 3D acceleration, which is not an acceptable solution. For those interested, here is the list of files to be deleted to stop having this problem. /System/Library/Extensions/ATIRadeonX1000.kext /System/Library/Extensions/ATIRadeonX1000GA.plugin /System/Library/Extensions/ATIRadeonX1000GLDriver.bundle /System/Library/Extensions/ATIRadeonX1000VADriver.bundle /System/Library/Extensions/ATIRadeonX2000.kext /System/Library/Extensions/ATIRadeonX2000GA.plugin /System/Library/Extensions/ATIRadeonX2000GLDriver.bundle /System/Library/Extensions/ATIRadeonX2000VADriver.bundle I would like to know if there is a way to fix this using other drivers if that's possible or by creating a group to force Apple to make a replacement program in place. Edit : How to locate those files on your hard drive if you are not under Snow Tiger : sudo find / -iname "*radeon*"

  Read the article

• Windows 7: Windows Firewall: Logging/Notifying on Outgoing Request Attempts

  - by Maxim Z.

  I'm trying to configure Windows Firewall with Advanced Security to log and tell me when programs are trying to make outbound requests. I previously tried installing ZoneAlarm, which worked wonders for me with this in XP, but now, I'm unable to install ZA on Win7. My question is, is it possible to somehow monitor a log or get notifications when a program tries to do that if I set all outbound connections to auto-block, so that I can then create a specific rule for the program and block it.? Thanks! UPDATE: I've enabled all the logging options available through the Properties windows of the Windows Firewall with Advanced Security Console, but I am only seeing logs in the %systemroot%\system32\LogFiles\Firewall\pfirewall.log file, not in the Event Viewer, as the first answer suggested. However, the logs that I can see only tell me the request's or response's destination IP and whether the connection was allowed or blocked, but it doesn't tell me what executable it comes from. I want to find out the file path of the executable that each blocked request comes from. So far, I haven't been able to.

  Read the article

• System hangs while rebooting on Debian...

  - by Usman

  Hi, I have Debian (Kernel 2.6.26-2-686) installed on two computers. On one of them it reboots quite finely but I am having following problem with rebooting Debian on my second computer. When i type reboot at the Linux prompt, following messages appear and system hangs up after saying "Restarting System": Broadcast message from root@myname (tty1) (Sun Jan 17 11:23:26 2010) The system is going down for reboot NOW! INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Saving system clock Stopping enhanced syslog: rsyslogd. Asking all remaining processes to terminate...done. Deconfiguring network interfaces...done. Cleaning up ifupdown.... Deactivating swap...done. [ 31.789103] Restarting System. _ Normally when the sytem is busy "" sign blinks but "" at the last line above does not blink which shows, the system hanged up. I tried all keys but the screen is still frozen at the same point. The difference that I noted between my two computers is that I don't have ACPI support in the BIOS of the system which is giving me this error whereas the BIOS of my first computer do have ACPI support on which Debain do not give this restart-hanging problem. I have also disabled running the acpid script by running update-rc.d -f acpid remove but the problem still persists on the second computer. Any ideas to solve or get around this problem?

  Read the article

• Reboot fails with "Invalid partition"

  - by Mike Clark

  My laptop can't reboot. Any time something restarts the laptop (e.g. to apply Windows updates, or Start Menu-Restart, etc), the computer sits at a black screen with the message "Invalid partition" displayed in console text. When this happens, I power off the computer, then power it back on, and it boots up fine. OK, now the history behind this: This laptop is a new Dell. The day I got it, I used gparted to reclaim 30 GB of disk space that had been allocated to a "recovery partition" in the middle of the laptop's primary drive. (I have DVDs for recovery and I didn't want to waste 30 GB of SSD space on recovery data.) So I used gparted to delete the recovery partition and resize the primary Windows partition to use up the new free space. As expected when resizing a boot partition, the computer would no longer boot. I used Windows Recovery Console to fix the boot process: FIXMBR C: FIXBOOT C: BOOTCFG /rebuild This worked fine and the computer boots up fine. But, as mentioned earlier, the laptop still can't reboot. Any idea on how to fix this without completely reformatting the disk and reinstalling Windows from scratch? It's Windows 7.

  Read the article

• Print jobs sent to server OK, but then get deleted

  - by Paul Morrison

  I have 2 HP computers, one running Win XP SP3, one running Win7. I have a Lexmark X4270 All-in-One printer attached to the Win7 machine via a USB port. I can print OK from the Win 7 machine, but when I print from the WinXP machine, the print job shows up in both print queues (showing the same number of bytes - which is good!), but then the status gets changed to "Deleting - Sent to printer", and that status shows up in both print queues. The print job then stays there until I do a cancel, followed by a system restart. FWIW the owner is shown as Guest, but I have permission for Everyone set to print... I believe I have up-to-date drivers; I don't believe it's a firewall problem. What I would like to see is the Win7 machine's reason for deleting my print jobs - is there a diagnostic tool available? Also, I notice that the port for this printer on the WinXP machine is set to USB001 - I would have thought something like \servername\sharedprinter would be more appropriate - and I can see that in the list of ports, but the system doesn't let me change the port name from USB001... Could someone shed some light? I have spent hours on this! TIA BTW I can do file sharing, no problem!

  Read the article

• PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded

  - by Tiny

  I'm trying to upgrade php 5.4.14 from php 5.4.3 in wamp server 2.2e. I have downloaded php-5.4.14-Win32-VC9-x86 (thread safe). Extracted it under C:\wamp\bin\php. Copied wampserver.conf from C:\wamp\bin\php\php5.4.3 to C:\wamp\bin\php\php5.4.14. Renamed php.ini-development to phpForApache.ini. -The port number the wamp server has been changed in the http.conf file to 8087 from its default 80. This is mentioned here though it is about upgrading from php 5.3.5 to php 5.4.0. After this, Restarting of the wamp server and services all over again has all been done and those two versions appeared in the menu php-versions (which is opened when the icon of the server is clicked). But when I attempt to enable a library like php_mysql or php_mysqli, a warning message box appears. PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded. I have also tried to removing the semicolon before them in the php.ini file but to no avail. I'm running Microsoft Windows XP Professional Version 2002, service pack 3. Where might be the problem? EDIT: I have changed extension_dir from C:\php to c:\wamp\bin\php\php5.4.14\ext\ in php.ini as the answer below indicates and the library is now loaded correctly but it says, 1045 - Access denied for user 'root'@'localhost' (using password: YES) though the user name and the password are the same as they are in MySQL in the config.inc.php file under phpmyadmin. I have also tried to restart MySQL56 service from Control Panel-Services(Local) but it keeps giving the same error. Does someone know why this happens?

  Read the article

• Cannot connect to server via SSH

  - by Rayne

  I'm running RHEL 6.0, and I accidentally moved the /bin, /boot, /cgroup, console.txt, /data, /dev, /etc to another folder. I think I managed to move these folders back, but now I'm having trouble connecting to the server using SSH, but am able to access the server via VNC. When I tried to connect to the server using a terminal from another server, I get the error ssh_exchange_identification: Connection closed by remote host I'm currently still connected via SSH to the server (haven't closed the window yet), and am still able to access it normally. But if I try to open a new SSH terminal from my current session, I see /bin/bash: Permission denied If I try to open a new SSH File Transfer window from my current session, I get the error File transfer server could not be started or it exited unexpectedly. Exit value 0 was returned. Most likely the sftp-server is not in the path of the user on the server-side I checked and I have Subsystem sftp /usr/libexec/openssh/sftp-server which is the same path as the output of locate sftp-server Also, when I tried to restart sshd, I get the error Couldn't open /dev/null: Permission denied But my /dev/null has the permissions crw-rw-rw- for root,root. How can I resolve this? ETA: Thanks for all your help! I was able to start ssh by running the application directly /usr/sbin/sshd Even though the status of the openssh-daemon is still "stopped".

  Read the article

• Troubleshooting wireless connection problem / site survey?

  - by johnnyb10

  I just started in the IT department of a small company (200 users) and it's clear that one of the main problems that is driving everyone crazy is the spotty nature of the wireless connectivity throughout the office, particularly in certain conference rooms. This is a huge problem because the connection often drops during important presentations to clients. I was hired to help ease the load on the existing IT admin, who has done a great job, but is overloaded with many other tasks to deal with. So I would like to try to help out with this wireless issue. I am looking for advice on the best way to solve this problem--a realistic troubleshooting methodology that does not require me to spend any money. So far, I've experimented with Ekahau Heat Mapper, which is free and helps create a site survey. But I'm not exactly sure what I'm looking for or if there are other programs/tools/methods I should try as well. Any advice would be greatly appreciated. [Some background: The wireless setup consists of an HP ProCurve Mobility MSM (710?) controller that controls 10 access points throughout the building. There are three virtual wireless networks configured on the controller: one seems to be a default that cannot be changed, one is for internal employees and authenticates via Active Directory, and the third is a guest network for visitors. When I use HeatMapper, these show up as three different SSIDs, with different MAC addresses, all on the same channel. At first I thought maybe this would cause interference, but this seems to be the way the controller works;apparently, it automatically configures the channels to avoid interference from the other APs on the network.]

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Ubuntu 12.4 compiz - disable all compiz plugin - empty screen

  - by gotqn

  A friend of mine has installed on my new machine Ubuntu 10.4 (I have always been windows user and have no experience with Linux). I started to watch some tutorial about how to make 'Rotated Cube' using 'Compiz',but the cube appears in the form of a list (only two slides). I have thought this could be result of my video cards (only two - one from the processor and one from the motherboard) and they can not support this options. Anyway, I have decided to disable all compiz plugins and options because my friend has set some, and I started to think there is some misunderstanding between the plugins. After, that I got only empty screen(no menu, no icons, anything) and can do nothing. How to fix this? EDIT: When I remove the compiz stuffs (from the console), the menu is shown again. Then I install the compiz again (some of the effect are still not working). After restart or log out/in the menu is hidden again. I suppose that there are some settings that I've broken but they are saved somewhere in the system and remove the compiz do not deleted them and as a result they are activated after compiz is installed again and the PC is restarted?

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >