Search Results

Search found 20225 results on 809 pages for 'computer parts'.

Page 303/809 | < Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >

  • Debugging Windows PC freeze

    - by Violet Giraffe
    I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

    Read the article

  • Am I getting the right memory for my motherboard?

    - by Daniel Carvalho
    Hi technophiles; I have a Gigabyte GA-EP45-DS motherboard. Also, the memory that came with my computer was two Transcend aXe RAM 1066MHZ 1GB modules. The thing is, I noticed that my motherboard has "DDR2 1200" written on it. This concerns me, have I bought slower memory than my computer is supposed to have ideally? Now, I'm not super concerned at a granular level about the best optimal RAM with the best CAS latency etc... but I do hope at least that I've got the right speed. Now, as far as I know, there is no such thing as ram at 1200MHZ? Am I right? You see, because I'm thinking of getting more RAM now, before I can't find the same type or speed any-more and just want to make sure it's the right thing. Furthermore, if the memory is slower than what I should be getting for my motherboard, what RAM should I be getting, and will that new RAM play nice with my old RAM? If I get new RAM at a different speed, would it be better / more beneficial performance-wise to omit the old RAM because of how the whole DUAL channel RAM thing works? I'm not too clued up on this area. Thanks chiefs.

    Read the article

  • EXCEL workbook, intermitently, takes 30 seconds to load

    - by Julio Nobre
    I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during workbook load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All workbooks where located on a local drive (C:\BPI); The workbook has no macros and no addins; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different workbooks (all of them smaller than 30 KB); I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbooks; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

    Read the article

  • Windows 7 notebook turn off by itself, how to check if it is due to CPU being too hot?

    - by Jian Lin
    I have a Dell Studio 15 notebook, and it just started turning off by itself yesterday. Could it be that the CPU is too hot? I have had several notebooks before and every one of them I can put them on the bed without any problem. This Dell Studio Notebook, however, seems like have the air / fan outlet pointed outward from the bottom back of the notebook, so I suspect that the air is partially blocked when it is on the bed. Are there Win 7 tools that can monitor the CPU temperature, or will some 3rd party tool be needed? (I try to stick to official tools nowadays). Also, it is running Win 7 Ulitmate, there is actually no utility or background service from Win 7 or from Dell that detects when the temperature is too hot (or 95% near the max), pop out a message box giving a warning and say that the computer will go into sleep mode in 1 minute, but instead just turn off the computer by brute force (cutting out the power) right then and there? Update: it turned off right in front of my eyes -- it is not doing any windows update or anything. just normal use and jooooop, it turned off.

    Read the article

  • Publishing an Excel spreadsheet using Microsoft SBS 2008 to a web page that is viewable by mobile ph

    - by Dave Heath
    I am getting well out of my “superuser” depth here and would love some support. At work we have an Excel workbook (*.xls format circa Office 2003) which maintains our “engineers” timesheet. This handles what events we are doing across the year and how many “work units” it is. As far as a workbook goes, it is fairly simple with just a few =SUM(range) cells and some linked across sheets (12 sheets, one for each month) It is stored on a server, in a folder that provides “management” with full access and “engineers” with read-only access. The workbook itself is read-only for “engineers” and full access for “management”. I think these permissions are controlled through Active Directory. The workbook is protected with a password, assumingly to allow “management” to edit it even if they are working at a terminal logged in as an “engineer”. This protection prevents “engineers” from going to certain cells to see formulae and therefore editing them. The workbook has a macro which saves and closes it ten minutes after opening. This is to stop other “management” from being locked out by any one person who has logged in with editing privileges. I hope this is making sense to someone... :S Now then, we have Microsoft Small Business Server 2008. We have a shiny new web-based login for when we are offsite so we can get to Exchange webmail and our internal site (which uses Sharepoint 3.0). “Management” would like to be able to publish this timesheet automatically after changes (they don’t want to have to do anything different to what they are currently doing) so that using an iPhone “engineers” can check on it while out of the office. I am currently having a look at “Excel Services” for Office 2007 on TechNet but I am not sure if I am running down the right garden path at the moment. < EDIT This seems to suggest that I have to have Sharepoint Server 2007, with no mention of Sharepoint 3.0... ... "MOSS builds on WSS by adding both core features as well as end user web parts" - Wikipedia entry for Microsoft Office SharePoint Server (MOSS) this is not good news... "...and using the ASP.NET APIs, web parts can be written to extend the functionality of WSS." Wikipedia entry for Windows Sharepoint Services. Could this bring back what I need? Is this good news? Do I need to start learning ASP.NET? This link here implies that we need MOSS to do what I want and the bosses say we aint' getting it. http://serverfault.com/questions/20198/what-is-some-cool-things-you-can-do-with-sharepoint-2007/22128#22128 Back to the drawing board. < /EDIT Please could someone suggest some “further reading” for me to help point me in the right direction or to put me back on the right track. Many thanks. I will try to keep this up to date with how I get on.

    Read the article

  • Timeout option not working on efi windows 7/windows8 dual boot machine

    - by Guenter
    I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

    Read the article

  • I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

    - by ChrisF
    Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

    Read the article

  • Un-install network printer drivers from Win7 64 Home Premium

    - by AkkA
    I recently bought a NAS device that has print server functionality through USB. The printer was already installed and fully working on another Win XP box, set up that box to see the printer over the network and it prints fine. I tried to install the printer on my Win7 laptop (64 bit, Home Premium), but got the wrong drivers somehow, or it just refuses to work. I need to completely un-install the printer drivers and start from scratch. Removing the printer (by going to the printers folder, right click and remove) does not actually un-install the drivers. It only removes the printer from active use. Even if I try to re-install new drivers it will load the old ones. I have read a few things on the net that say to load up a device snap-in or something of the sort into Computer Management, but this seems to be valid for Win7 Pro or greater, the function everyone tells you to use isnt available in Home Premium. Is there anything I can use to manage device driver files in Home Premium? I want to completely remove them from the computer.

    Read the article

  • Cannot Access Shared Folder From IIS

    - by Tim Scott
    From IIS I need to access a folder on another computer. Both servers are Window 2008 SP2, and they live in a Virtual Private Cloud on Amazon EC2. They reach one another by private IP -- they are in WORKGROUP, not a domain. I can access the shared folder manually when logged in to the client as Administrator. But IIS gets "access denied." Here's what I have done: Set File Sharing = ON Set Password Protected Sharing = OFF Set Public Folder Sharing = ON Shared the folder Added permission to the share: Everyone, Full Control Added permission to the share: NETWORK SERVICE, Full Control Verified that File & Printer Sharing is checked in Windows Firewall Opened port 445 to inbound traffic from local sources I tried adding <remote-machine-name>\NETWORK SERVICE to the share but it says it does not recognize the machine, which makes sense, I guess. As I said, from the other computer I have no trouble accessing the shared folder from my user account, but IIS is shut out. How does the file server even know the difference? I would assume that with Everyone given full control and password protected sharing turned off, it would not matter what the client user account is. In any case, how to solve? UPDATE: To clarify, I am not trying to serve up files on the share directly through IIS. Rather I am writing files to the share from my code (System.IO).

    Read the article

  • External SATA drive does not work without the optional USB cable *also* connected

    - by Software Monkey
    I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

    Read the article

  • Screen Flicker on a black MacBook

    - by sixtyfootersdude
    I have a MacBook Black. For about the last six months I have had a strange screen flicker when I: start my machine and plug in the power cord of my machine This morning when I woke up my computer the screen backlight did not turn on at all. When I held the computer in direct sunlight I could see the screen and I could tell that everything was working normally (other than the backlight). Pressing the screen brightness controls (F2) brought up the brightness panel. The brightness panel informed me that the screen was at maximum brightness. I did a bit of Searching and this is what I found: This post describes how to buy and replace a macbook screen. Do you think that this would solve my problem? Additional info: I am running 10.6.4 I recently upgraded from 10.4. I experienced similar issues in 10.4. I am pretty sure that this is a hardware issue. The problem does not occur when the screen is at a specific angle. It usually only happens at startup/wakeup or when the power is plugged/unplugged.

    Read the article

  • Why does my PC successfully boot only when unplugged for more than a few minutes?

    - by philg
    I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

    Read the article

  • PC power supply & normal range for voltages reported in BIOS hardware monitor?

    - by Chris W. Rea
    I'm trying to diagnose whether my computer has an ample power supply. Sometimes when I play a video-intensive game, both monitors lose the video signal, even though the computer remains on and sound playing. A theory I have is: the video card isn't getting sufficient power. I can't imagine it's overheating because the machine is well-ventilated and the video card isn't hot to touch when this happens. Anyway, in my PC's BIOS there's a Hardware Monitor page, and among other voltages reported (such as CPU, DRAM, South Bridge, etc.) I can see the following values: 3.3V 3.152V 5V 4.944V 12V 11.872V Are those the voltages used by peripherals? What voltage should I be referencing if I want to know what my video card (PCI Express) is consuming? What is the normal range of values reported for those? My values above appear to be under by approximately 4.5%, 1.1%, and 1.1% respectively. Is that cause for concern? How else should I be determining if my power supply is "right-sized" for my PC and video card, or am I perhaps barking up the wrong tree?

    Read the article

  • Will wear induced by turning computers off in the evening be offset by energy savings?

    - by sharptooth
    I'm asking this here because this is primarily a huge office scenario and administrators will more likely have the answer I'm looking for. Employees' desktop computers can be either left turned on for the whole night or switched off in the evening and turned back on in the morning. The latter will surely save energy. In the same time turning on and off is very harmful for the equipment - hardware often breaks specifically when turned on. Both energy and hardware replacements cost money. With energy it's quite obvious - you pay every month according to what your power meter shows. With hardware replacements it's worse - you need qualified stuff to quickly diagnose the problems and once something breaks the affected employee will have to wait for some time while his computer is fixed/replaced and the data is recovered. So the company has to choose between saving money on energy and saving money on computer maintaince and lost hours. Such decisions must be well though. Is there any detailed study of how turning computers off each evening affects their lifetime?

    Read the article

  • cannot connect to vpn server (error 721)

    - by callmeblessed
    Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

    Read the article

  • Win7 System folder contains infinitely looping SYSTEM(!) directory

    - by Matt
    My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

    Read the article

  • Extract a section of a tgz file

    - by TRiG
    I have a 28.5 GB .tgz file which was created on the command line of a Linux computer, compressing one folder and all its many many subfolders. I now want to extract a single sub-sub folder from that .tgz file, using 7zip on Windows Vista. I can't see a way to do it. Opening the .tgz file in 7zip just shows the .tar file inside it. There doesn't seem to be any way to browse that .tar file and extract the section I want. I assume there is a way to do this, but I can't see it. Simply double-clicking on the .tar file brings up a progress bar which runs slowly till my computer complains it's running out of space; I imagine it's trying to extract the whole thing. Searching for "extract section of tgz" and "extract tgz subfolder" and similar found me a way to do it on the Linux command line, but no obvious way to do it on Windows. (Most results found were about extracting into a subfolder, not extracting a subfolder out of the archive.)

    Read the article

  • Files deleted. What could have happened?

    - by jjfine
    I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

    Read the article

  • Server freezes while installing Redhat Enterprise Linux Server 6

    - by eisaacson
    We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

    Read the article

  • How do you enable view source in ie8 when it gets magically diabled

    - by Tim Meers
    I have multiple computers that all seem to have View Source disabled from the content menu when you right click on a web page. Now I know it's not that the web page is some how disabling it, I'm pretty sure thats not even possible. But alas I have at least 3 machines in my office (not on AD) that have this problem. I have also worked on clients computers that have this same issue. It's down right maddening! I tried to Google for it, but it just shows results from the dawn of IE6 in all of it's "glory" with a bug where if the cache was full it would be disabled. But this is not the case in IE8. Any body have a clue why this is happening, or a fix for it? Maybe a reg setting? Update: So I got a little closer to solving it, but there was still an issue on one computer where it allowed it not is HTTP, but not in HTTPS. One other computer works correctly in both. I Found these two keys missing in the registry: [-HKEY_CURRENT_USER\SOFTWARE\Microsoft\Internet Explorer\View Source Editor] [-HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\View Source Editor]

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

    Read the article

  • Dell XPS 1530 DVD-RW firmware problem

    - by josecortesp
    Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

    Read the article

  • How can I make an encrypted email message into a .p7m file?

    - by Blacklight Shining
    This is a bit complicated, so I'll explain what I'm really trying to do here: I have a Debian server, and I want to automatically email myself certain logs every week. I'm going to use cron and a bash script to copy the logs into a tarball shortly after midnight every Monday. A bash script on my home computer will then download the tarball from the server, along with a file to be used as the body of the email, and call an AppleScript to make a new email message. This is where I'm stuck—I can't find a way to encrypt and sign the email using AppleScript and Apple's mail client. I've noticed that if I put a delay in before sending the message, Mail will automatically set it to be encrypted and signed (as it normally does when I compose a message myself). However, there's no way to be sure of this when the script runs—if something goes wrong there, the script will just blindly send the email unencrypted. My solution there would be to somehow manually create a .p7m file with the tarball and message and attach it to the email the AppleScript creates. Then, when I receive it, Mail will treat it just like any other encrypted message with an attachment (right?) If there's a better way to do this, please let me know. ^^ (Ideally, everything would be done from the server, but there doesn't seem to be a way to send mail automatically without storing a password in plaintext.) (The server is running Debian squeeze; my home computer is a Mac running OS X Lion.)

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

    Read the article

  • UAC being turned off every time Windows 7 starts

    - by Mehper C. Palavuzlar
    I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. I never disable UAC, but obviously some process or virus (I'm not sure, only guessing) causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I really don't know what causes the problem. I have run a full scan on the computer for any probable virus activity, but TrendMicro OfficeScan said that no viruses have been found. Malwarebytes' Anti-malware could not find any malicious items either. There are no other strange incidents on the machine. Everthing works fine except this bizarre incident. How can I learn what process is trying to turn off UAC? What way should I follow to overcome this problem?

    Read the article

< Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >