Search Results

Search found 9122 results on 365 pages for 'sound card'.

Page 305/365 | < Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >

• Strange performance issue with Dell R7610 and LSI 2208 RAID controller

  - by GregC

  Connecting controller to any of the three PCIe x16 slots yield choppy read performance around 750 MB/sec Lowly PCIe x4 slot yields steady 1.2 GB/sec read Given same files, same Windows Server 2008 R2 OS, same RAID6 24-disk Seagate ES.2 3TB array on LSI 9286-8e, same Dell R7610 Precision Workstation with A03 BIOS, same W5000 graphics card (no other cards), same settings etc. I see super-low CPU utilization in both cases. SiSoft Sandra reports x8 at 5GT/sec in x16 slot, and x4 at 5GT/sec in x4 slot, as expected. I'd like to be able to rely on the sheer speed of x16 slots. What gives? What can I try? Any ideas? Please assist Cross-posted from http://en.community.dell.com/support-forums/desktop/f/3514/t/19526990.aspx Follow-up information We did some more performance testing with reading from 8 SSDs, connected directly (without an expander chip). This means that both SAS cables were utilized. We saw nearly double performance, but it varied from run to run: {2.0, 1.8, 1.6, and 1.4 GB/sec were observed, then performance jumped back up to 2.0}. The SSD RAID0 tests were conducted in a x16 PCIe slot, all other variables kept the same. It seems to me that we were getting double the performance of HDD-based RAID6 array. Just for reference: maximum possible read burst speed over single channel of SAS 6Gb/sec is 570 MB/sec due to 8b/10b encoding and protocol limitations (SAS cable provides four such channels).

  Read the article

• Cisco 837 not passing UDP traffic properly (was: DNS query problem)

  - by TessellatingHeckler

  We have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch - LAN. It has been fine for years, suddenly DNS resolution stopped working from the LAN to public DNS servers. No changes that I know of, so I can't revert anything. Current behaviour: DNS requests from the LAN using TCP show up in the oubound firewall log, in the Cisco debug log, in the dns-server-firewall, in tcpdump on the DNS server, the answer comes back, it works fine. DNS requests from the LAN using UDP show up in the outbound firewall log, in the Cisco debug log, but does NOT show in the dns-server-firewall, not in tcpdump on the DNS server, times out. DNS requests from the Cisco using UDP show up in the dns-server-firewall and in tcpdump on the DNS server, answer received, works fine. netcat connections to port 53 or a random port by TCP show up in the dns-server-firewall netcat connections to port 53 or a random port by UDP do not show up in the dns-server-firewall Summary: TCP seems fine throughought. UDP works from the Cisco over the ADSL, and it works from the LAN to the Cisco, but it doesn't seem to cross the Cisco 837 properly. Update: confirmed with netcat that any UDP traffic from the LAN is affected, not just traffic to port 53. Update: If I change the firewall's external IP to any other IP in the subnet, this starts working. When I put it back, it stops working. I now suspect it's an ISP issue (does that sound plausible?), and am removing the Cisco config.

  Read the article

• SAS vs Near-line SAS vs SATA

  - by David

  I'm unsure about the differences in these storage interfaces. My Dell servers all have SAS RAID controllers in them and they seem to be cross-compatible to an extent. The Ultra-320 SCSI RAID controllers in my old servers were simple enough: One type of interface (SCA) with special drives with special controllers, humming at 10-15K RPM. But these SAS/SATA drives seem like the drives I have in my desktop, only more expensive. Also my old SCSI controllers have their own battery backup and DDR buffer - neither of these things are present on the SAS controllers. What's up with that? "Enterprise" SATA drives are compatible with my SAS RAID controller, but I'd like to know what advantage SAS drives have over SATA drives as they seem to have similar specs (but one is a lot cheaper). Also, how do SSDs fit into this? I remember when RAID controllers required HDDs to spin at the same rate (as if the controller card supplanted the controller in the drive) - so how does that work out now? And what's the deal with Near-line SATA? I apologise about the rambling tone in this message, it's 5am and I haven't slept much.

  Read the article

• How can I calculate power consumption of my PC in Watt?

  - by Jitendra vyas

  How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

  Read the article

• Macbook Pro 2010 Ethernet Jumbo Frame(9k MTU) Support?

  - by Troggy

  Has anyone been able to use jumbo frame support on their 2010 Macbook Pros? This is kind of negative news here, but I am seeing many reports that this is not available anymore due to Apple's choice of network card in the new machines. I cannot set my MTU speed over 1500 on my new 2010 MBP i7, but my old early 2008 MBP (Core2) has the 9000 MTU setting for use. Everything I have is setup to use jumbo frames and I thought apple kept that feature in their "pro" lineup. It sounds like the Mac Pro still has it. Did they decide to use a chipset that doesn't support it? I am trying to pinpoint some solid chipset numbers and the feature support. Maybe they just need to update the drivers? Is there some more official information about this feature? This might seem minor, but this is really frustrating if apple removed this feature from their pro laptop line. From what I have read so far, it sounds like I am not alone in my frustrations with this. http://discussions.info.apple.com/message.jspa?messageID=12258067 http://discussions.apple.com/thread.jspa?messageID=12130158 Anyone have any experience or further knowledge about this issue ... beyond typing my question into google and giving the top 5 results as answers? :)

  Read the article

• Not recognizing second monitor after hibernate (Windows 7, Dell D630 laptop)

  - by Brooks Moses

  I have a Dell Latitude D630 laptop which I've recently updated to Windows 7 64-bit. (The Dell site confirms that it's Windows-7-compatible.) Normally it lives in a docking station with a second monitor connected to the DVI port on the docking station, and I use the second monitor in a multi-monitor configuration with the laptop screen. Sometimes I undock the laptop and use it separately. Here's the problem: If I hibernate the laptop while undocked, and then power it back up in the docking station, it does not recognize the second monitor. By which I mean that not only does it not share the desktop onto the second monitor, but if I go into the control panel for display settings and press "Detect", it does not even detect the existence of the second monitor. I can tell it to "use the VGA port anyway" for a second monitor, but the monitor is connected to a DVI port on the docking station, so that doesn't do anything useful. If I entirely reboot the laptop while it's connected to the docking station, it has no problem recognizing the second monitor and using it. But then, if I hibernate, undock, de-hibernate while undocked and rehibernate, and then re-dock and de-hibernate, it's back to not recognizing the second monitor again. I'm reasonably certain that this is not a limitation of the hardware; this worked fine on Windows XP. I'm currently using the Windows 7 driver for my video card. I attempted to use the video driver from the Dell website for this laptop, but Dell only provides Vista 64-bit drivers, not Windows 7 64-bit drivers. Their "Windows 7 compatibility" page suggests that the Vista drivers should work, but when I attempted to install the driver, it gave me a "this operating system not supported" error and refused to install. Any further ideas?

  Read the article

• Hardware Requirements & Tuning - Flash Media Server 3.5 Interactive

  - by Anthony Kanago

  I am trying to spec out a server to purchase (physically, not rented from someone like softlayer.com) to run an intranet instace of Flash Media Server 3.5 Interactive. In general, the server will likely be fielding somewhere on the order of 400 connections at a time at the upper limit. Of course, should this increase, we don't want to be stuck. While the decision is not final, we will likely be running the server on Red Hat rather than Windows. The server will be run on gigabit ethernet. I have two related questions: What sort of hardware would I need realistically to support this? What advice can you offer for settings in tuning FMS/the OS to be performant to this level? We are looking for a bare minimum that will run this effectively to save on costs. Realistically, the average number of connections will be fairly low (50-150) by comparison with that upper limit estimate. To reiterate: we just want to be cautious in not getting caught when we need more power, but we also need a low-cost solution (doesn't everyone?) and that may take priority. Windows and RedHat are the two officially supported operating systems. Since FMS is stated to be 32-bit only, I'm sticking with a 32-bit OS. The hardware requirements listed by Adobe on their website are: 3.2GHz Intel® Pentium® 4 processor (dual Intel Xeon® or faster recommended) 2GB of RAM (4GB recommended) 1Gb Ethernet card So what realistically do I need for those sorts of connection numbers, and what can I due to tune things up to get more out of less hardware? Thanks!

  Read the article

• MacBook Pro screen flickers, and lines appears after using it a while

  - by Adam L. S.

  My aunt gave me her old MacBook Pro, but unfortunately it has a few issues. The main problem is that lines appears after I use it with applications that heavily depend on graphics, but they don't necessarily appear in that window. I also figured out that these lines appear with the windows, so the cursor goes over the lines, and menus and other windows also overlap them. If I take a screenshot of the window by itself, no lines appear. It seems obvious to me that this is a driver-related problem. Unfortunately, there are no updates or anything for the driver. At first I tried asking for a solution at Apple's forum, but they were only able to figure out that "something is wrong with the video card". I checked the MacBook with an Ubuntu disk, and the screen seemed OK. I've uploaded some photos to my Picasa account to show the symptoms. Recently, I've also noticed the screen flickering when using applications that need high performance graphics, like games. Also, the MacBook Pro came with Mac OS X Tiger, but she upgraded it to Leopard (she only brought the Tiger disk with her.) What can I do with this?

  Read the article

• Low CPU performance with low usage and clock - Windows 8.1

  - by Daniele

  I recently deleted everything from my PC and reinstalled Windows 8.1 from scratch. When I first booted into Windows everything was extremely slow though the CPU usage was very low (about 1%). After installing some drivers the problem seemed to be solved, I was able to use my PC normally. Today I installed a game and I noticed a strange behavior: the game was playable but the performance worsened more and more in the time. This is the situation BEFORE opening the game (normal): This is AFTER some minutes inside the game (low CPU usage and clock): Some information about my system: PC: Sony Vaio S13 (SVS13A1C5E) OS: Windows 8.1 CPU: Intel Core i7-3520M 2.90GHz GPU(1): Intel HD Graphics 4000 GPU(2): NVIDIA GeForce GT 640M LE I tried searching for new drivers and other solutions but noting worked and I don't know what is the cause. I did not checked the temperatures but the fans are not running fast and the PC does not look overheated. Update: Max CPU Temp: 66°C, Max GPU Temp: 61°C The strange thing is that the GPU load is 99% (GPU-Z) and the fan is almost silent. Update 2: I had troubles with Sony Vaio software, I can't get the FN keys and the STAMINA/SPEED switch to work (it is a physical switch to enable/disable the Nvidia card and change the Power Profile). I'm saying this because I remember that before reinstalling Windows there was an option in the Vaio Control Center (now it is not there anymore) that allowed me to choose from something like "priority to performance (ventilation)" or "priority to silence". The current behavior looks like a "priority to silence", but I can't get the stamina-speed switch to work and so I don't see similar oprions in the Vaio Control Center. I don't know if the problem is related to this.

  Read the article

• SIP and NAT routers?

  - by OverTheRainbow

  Hello SIP was not built with NAT routers in mind, and I'd like to get to the bottom of this issue to check what needs to be done on all devices so it works with NAT routers, and understand in what context it just can't be used and I should check more NAT-friendly alternatives like IAX. A picture being worth a thousand words, here's the layout I need to use: http://img62.imageshack.us/img62/4077/sipandnatrouters.jpg The PBX server is located in the private LAN behind a NAT router connected to the Internet (I know it'd be easier if it were located in the public network, but this router doesn't support DMZ's so the server has to be in the private network) A couple of (soft|hard)phones are located on the same LAN and connected to the PBX server, along with a PSTN gateway (Linksys 3102 or a Digium PCI card) Remote users using (soft|hard)phones are located somewhere on the Net with dynamic IP's and are also located behind NAT routers I may or may not have control over the local NAT router where the PBX server is located, but I have no control over the remote NAT routers, either because the users don't have the computer knowledge to map ports or because the routers are off-limit (eg. web cafés, hotel LAN's, etc.) Is it possible to configure the PBX server, the (soft|hard)phones, and the PSTN gateway so that the all conversations work fine, no matter the endpoints (POTS caller/local phone, POTS caller/remote phone, local phones, remote phone/local phone)? In which cases may I expect problems, and are there solutions? FWIW, I'm leaning toward using Freeswitch, but I could end up using Asterisk if there are technical advantages to it in this context. Thank you for any info.

  Read the article

• Can't get an IBM xSeries 345 server to load Windows Server 2003 using ServerGuide utility

  - by Kyle Noland

  I have a client that has an IBM xSeries 345 eServer. Per the IBM support website, I have downloaded the ServerGuide Setup 7.4.17 installation ISO and burned a bootable CD. The CD boots fine and loads the utility. I walk through the following screens without any issue: Set the date and Time Detect the IBM ServeRAID card and install the latest firmware Clear the hard disks Set up the RAID array The next step is format the NOS partition. I select my partition size and the utility goes through the following steps: Creating NOS partition Formatting NOS partition (NTFS) Copying W32 files The copying W32 files takes about 10 minutes. I see the CD drive and disks working hard. When the copying is complete, I'm taken to a blank page just NOS Partitioning at the top. At the bottom of the screen are the familiar Back and Exit buttons. I see the place where the Next button should be, and if I click on it I can tell there is something there, but the space is empty. No button is displayed and clicking the empty spot doesn't ever take me to the next screen. I can't load the OS until I get past this part. I have already tried: Burning multiple copies and versions of the ServerGuide CD Letting the final screen just sit there over the weekend thinking it might advance after syncing the drives or something Has anybody else seen this? I'm really at a loss here. EDIT: I found another person who has the exact same problem as me: http://www.ibm.com/developerworks/forums/thread.jspa?messageID=14451763

  Read the article

• What is the advantage of not running as root? [closed]

  - by Shmuel Brill

  Possible Duplicate: What's wrong with always being root? All modern brands of Linux highly discourage (or disable) one from running as root instead of a normal user. I do not understand why. As a "normal" user, one could Download a rouge program from the internet. Run it (After all, one isn't root, what can it do). It installs itself in .bashrc or .xinitrc It writes a rouge "sudo" and "su" and adds . to the path Not noticing that . is in path, one runs sudo. The rouge program now has root password and can do anything it wants in the system. Even if 3-6 doesn't happen, the program could still Be part of a botnet. Read all files in the home directory and send them back (mine for SS#, Credit Card numbers, bank account numbers, etc). Send spam. Run a backdoor server to allow an attacker a chance to connect to the machine to determine vulnerabilities. It seems that the whole "permissions" thing (root/non-root) is just to prevent amateur crackers from getting into the system, so the question is: Is there a point in avoiding running as root, and is there a way to protect oneself if one wants to run unsafe code?

  Read the article

• How powerful of a PC do you need to edit HD videos?

  - by Xeoncross

  I have a Core2Quad Q8200 (2.3GHz) with 4GB of RAM, a 512MB PCIe video card, and a SATA-2 HD. Yet it still isn't fast enough to edit 720i/p video in Sony Vegas or Adobe Premiere/Aftereffects. My RAM usage never peaks over 1.6GB, but my CPU cores make it to 95% quick! Right now the preview panes in all these programs lag to bad to actually work on the videos. I get to see 1-3 frames every second or two! So how fast do I have to go? At what point will my CPU be fast enough to actually edit these videos? I have to assume that regular people and their regular sub $2k computers can actually work with this footage. Another way to answer this is, how fast is the PC you used to edit videos? Update: I'ts worth noting that now that I have Adobe Pre/AF CS4 I am more interested in getting that working than my older Vegas 6. If you didn't have to re-run RAM preview every, single, time you made one change it would be my answer. But since I like to test many filters and effects before choosing one - I have to re-render a 1-sec section of footage over-and-over and it drives me nuts waiting. Perhaps a motherboard with Dual Xeon chips or something would be able to handle this. It would probably be as much as a dual-crossfire setup and would also speed up other applications.

  Read the article

• SQL Server 2008 cluster freezing

  - by Ed Leighton-Dick

  We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

  Read the article

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• Windows Server 2008 R2 SP1 Drivers Missing Would Not Install?

  - by bleepzter

  I am building my dev machine with WS2008R2SP1. I consider Windows Server as the best development environment for C# since I tend to focus on server-centric (integration) applications. The desktop flavor of Windows (7) doesn't play nicely with things like Commerce Server or BizTalk... so I to like stick to the environment I develop for. Previously I used to develop inside of VM's but I've found that it is super inefficient and tends to take a toll on the laptops. (I've gone through two of them in 6 months). Problem is that I multiple devices that do not want to be recognized by Windows: My machine is Dell Precision M4500: Intel Core i7-Q740, 1TB HDD, 8GB RAM, Dell re-branded Broadcom DW1501 802x11n Half-Mini Card, Dell re-branded Broadcom DW375 Bluetooh Module, Intel 82577LM Gigabit Network connection NVidia Quadro FX1800 Graphics The devices in question are the Dell rebranded broadcom network and bluetooth adapters: Broadcom USH: USB\VID_0A5C&PID_5800&REV_0101&MI_00 USB\VID_0A5C&PID_5800&MI_00 DW375 Bluetooth Module USB\VID_413C&PID_8187&REV_0517 USB\VID_413C&PID_8187 When I ran the broadcom installers I get "Operating System not supported" which I think is a big oversight on Broadcom's part. Why check for system version string? UGHGHGH Moreover if I try to manually force the driver in windows... I get an error: Driver Management concluded the process to install driver FileRepository\btwampsecfl.inf_amd64_neutral_d8fc2b85d035ed47\btwampsecfl.inf for Device Instance ID USB\VID_0A5C&PID_5800&MI_00\7&66DE6C9&0&0000 with the following status: 0xe0000217. '- or - Driver Management concluded the process to install driver FileRepository\btwampfl.inf_amd64_neutral_d4c4acf036c61299\btwampfl.inf for Device Instance ID USB\VID_413C&PID_8187\90004EEEF5A6 with the following status: 0xe0000217. I googled the 0xe0000217 error code and it says Bad service install section in the driver inf file... Any ideas on how to fix this? I also tried the post by BetaIQ on MSDN Forum, unfortunately the links to the driver package included in the post were dead :( PS. On a side note I also do mobile development for Android, iOS, and Windows Phone, and BB. Having the bluetooth is quite useful with mobile devices.

  Read the article

• Windows 2003 DNS or IIS6 Problem?

  - by Mario

  Weird DNS problem... We have an intranet located internally on a windows 2003 / iis6 server - DNS handled internally on another windows 2003 server. The intranet, amongst other functions, hosts a ecommerce store I wrote that sells nike apparel embroidered with our company logo. Up until recently, it would send an email to payroll and the cost would be deducted from the employees paycheck. lets say this store is located at http://mydomain.com (only available internally) Now, we've been told by the accountants that we can no longer auto deduct from payroll and the employee needs to pay with a credit card or cash. So i went to thawte.com and ordered an SSL cert to be on the safe side (even though the CC gateway is secure) and they told me i need to drop the .com from the domain name Not wanting to mess with a system thats perfectly functional, i created another DNS entry that just points to mydomain (no .com) and left the old one in there. so they would go to http://mydomain On my Mac (OS X 10.6) i can hit either one just fine On Windows XP / Windows XP Embedded or Windows 7 (the vast majority of the pc's on our network) http://mydomain - returns nothing http://mydomain.com still works https://mydomain.com works but says the cert is invalid (as it should, it was issued to mydomain - not mydomain.com) my question is: why does it work on my Mac and not on a Windows PC (i get dhcp and dns just like any other pc on the network) and will removing the .com one from the DNS server resolve this? I've done all the usual attempts - ipconfig /flushdns, ipconfig /renew and release even going so far as to stop and restart DNS client on my Windows 7 box; rebooting and shutting down - adding a regedit entry something along the lines of SecureResponses and rebooting nothing works... I think its the .com and the not conflicting in DNS but i'm not sure - and why not on OS X We're closed on sunday and i'm going to remote in and see what happens if i remove the .com from DNS but any other ideas? -Mario

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Random Hard Freeze of Windows 7 (is Kaspersky to be blamed for this?)

  - by Christian Ivicevic

  The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

  Read the article

• Howo to get Multipath IO with Dell MD3600i into active/active setup?

  - by Disco

  I'm desperately trying to improve performance of my SAN connection. Here's what i have: [root@xnode1 dell]# multipath -ll mpath1 (36d4ae520009bd7cc0000030e4fe8230b) dm-2 DELL,MD36xxi [size=5.5T][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac][rw] \_ round-robin 0 [prio=200][active] \_ 18:0:0:0 sdb 8:16 [active][ready] \_ 19:0:0:0 sdd 8:48 [active][ghost] \_ 20:0:0:0 sdf 8:80 [active][ghost] \_ 21:0:0:0 sdh 8:112 [active][ready] And multipath.conf : defaults { udev_dir /dev polling_interval 5 prio_callout none rr_min_io 100 max_fds 8192 user_friendly_names yes path_grouping_policy multibus default_features "1 fail_if_no_path" } blacklist { device { vendor "*" product "Universal Xport" } } devices { device { vendor "DELL" product "MD36xxi" path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And sessions. [root@xnode1 dell]# iscsiadm -m session tcp: [13] 10.0.51.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [14] 10.0.50.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [15] 10.0.51.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [16] 10.0.50.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c I'm getting very poor read performance : dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=1000 The SAN is configured as follows: CTRL0,PORT0 : 10.0.50.220 CTRL0,PORT1 : 10.0.50.221 CTRL1,PORT0 : 10.0.51.220 CTRL1,PORT1 : 10.0.51.221 And on the host : IF0 : 10.0.50.1 IF1 : 10.0.51.1 (Dual 10GbE Ethernet Card Intel DA2) It's connected to a 10gbE switch dedicated for SAN traffic. My questions being; why the connection is set up as 'ghost' and not 'ready' like an active/active configuration ?

  Read the article

• Put one monitor of a dual monitor windows system into standby

  - by Psycogeek

  Standby not Disabled! When running 2 monitors on windows 7 or Windows XP, I would like to be able to put one of the monitors at a time into standby. The method can be manual. When running 2 monitors , the second monitor is not always needed, shutting off the monitors own power switch will turn off the monitor, that does work Ok. Problems with that are , the delay with the monitor logo at turn on, and the power switch is not very accessable, and the switch might not live forever turning it on and off so many times. Using disable methods like devcon, WIN-P and Display, causes all the windows to properly move to the other monitor. While that is what a person would want to happen so they can get hold of the windows, that is not what I want to happen, and some things on the other monitor have to be re-arranged after a re-enable. By putting it into standby mode, nothing changes other than the monitor going into standby. Disconnecting the DVI cable still can cause the system to (properly) shift all the windows over to the one monitor, just like any of the disable methods do. That makes a mess of the windows, and is so unacceptable, that I would prefer to leave the monitor on, wasting power and the hardware, when it could easily go into standby for some time. For both monitors I am using a "MonitorOff" program that puts both monitors into standby, but I can not find a utility that will put only ONE monitor into standby for the windows system. If someone comes along and suggests "ultramon" you must know for a fact that it will put One of either of the monitors into actual standby. And it does not really suit me to use ultramon, I tested it (it was nice) and I did not feel that it was a program I wanted. The 2 monitors are running off of an ATI 4890 card, they are both hooked up DVI-I, the OS is both Windows 7 (primary) and Windows XP. In addition it would also be interesting to have seperate standby activity timers, and follow mouse kind of standby changes, but any manuel method , shortcut, batch , tray, or gadget kind of operation would be a good start.

  Read the article

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

< Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >