Search Results

Search found 9456 results on 379 pages for 'controller'.

Page 307/379 | < Previous Page | 303 304 305 306 307 308 309 310 311 312 313 314  | Next Page >

• Expected IOPS for log writing on PS6000X SAN?

  - by dssz

  Customer is experiencing poor Sybase ASE 15 performance on a PS6000X SAN with 16 X 450GB 10K in RAID-50. The server is a Dell R710 running 2003 server R2 64bit in ESX 4.0.0,256968 I've used sqlio to benchmark the sequential write performance of 4KB blocks on the drive. sqlio -kW -t1 -s600 -dE -o1 -fsequential -b4 -BH -LS sqliotestfile.dat Result is 1900 IOPS. However, when Sybase is running a sustained workload of small inserts SAN HQ shows a consistent 590 IOPS (and 100% 4K write activity). It also shows that the write latency increases to 1.2ms from <1ms. Monitoring and tests in Sybase demonstrate the performance problem is IO related and in particular there is a lot of wait time writing to the log. The SAN indicates that write caching is enabled. What IOPS should the SAN be capable of for 4k sequential write activity? Also, with write caching enabled, shouldn't the controller be batching up the 4K writes into something more efficient? Also, any tips on Sybase on ESX would be appreciated.

  Read the article

• WS2008 NTP - Using time.windows.com,0x9 - Time always skewed forwards

  - by David

  I have a domain controller configured to use time.windows.com (with 0x09 flags set). I've noticed that frequently the systems' clock is fast - it varies from 10 minutes to even 45 minutes. I always have to keep resetting the system date/time back to what it should be. When I run "w32tm /query /source" it tells me it's using time.windows.com, and obviously I trust Microsoft not to serve incorrect times, but why is my server's clock fast? EDIT: There are a few Time-Service events in the System log: Event ID: 142 Message: The time service has stopped advertising as a time source because the local clock is not synchronized. Event ID: 139 Message: The time service has started advertising as a time source. These two messages appear in pairs every hour or so. Event 142 appears 14 to 16 minutes after 139 appears. Going back a few months, these events appear: Event ID: 35 Message: The time service is now synchronizing the system time with the time source time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 37 Message: The time provider NtpClient is currently receiving valid time data from time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 47 Message: Time Provider NtpClient: No valid response has been received from manually configured peer time.windows.com,0x9 after 8 attempts to contact it. This peer will be discarded as a time source and NtpClient will attempt to discover a new peer with this DNS name. The error was: The time sample was rejected because: The peer is not synchronized, or it has been too long since the peer's last synchronization. These three events only appear once in the log, back in October.

  Read the article

• Can't connect two PCs to a Network Switch at the same time (Windows 7)

  - by puk

  I have two computers connected to a network switch and every once in a while one of the computers will lose its internet connection. It's almost always the same computer every time. However, if I play around with the control panel, I can switch it, so that now the other computer is not connected. Restarting either of the computers does not help either. In Windows, the worlds-greatest-trouble-shooter tells me that a network cable is unplugged and that I should try plugging it in...Disabling and re-enabling my NIC does not fix this problem, neither does swapping cables around. When rebooting, the BIOS complains about how the Ethernet Cable is not plugged in. If it's in any way important, My set up at the office is like so: Modem - Routher - Network Switch 1 - Network Switch 2. I have tried turning off the energy saving option for my NIC, and I tried manually setting the link-speed to 100Mbps Full Duplex without any luck. Also, I have a Realtek PCIe GBE Family controller on both computers Does anyone have any idea why this is happening every 5-10 days? EDIT: I have also tried using a completely different Network Switch and the problem still persists as before.

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• Linux machine can't find its tape drive

  - by Kyle Hodgson

  I have an older HP NetServer LPr with what is apparently a Symbios SCSI card connecting to a Quantum SuperLoader 3 that is DLT based. From time to time, we seem to lose the connection to the autoloader. It's usually due to flaky power, but not totally sure why; sometimes when this happens the Autoloader's LED's are orange and it needs to be power cycled. The annoying workaround currently is to reboot the machine. As it is our production VPN and DNS server in addition to being our backup server, this is less than optimal. In Debian (Sarge) is there not some command one can type to get the card to notice that it has the autoloader connected again? dcr1:/proc# grep -i symbios /proc/pci SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 1). dcr1:/proc# uname -a Linux dcr1 2.4.27-3-686 #1 Tue Dec 5 21:03:54 UTC 2006 i686 GNU/Linux dcr1:/proc# mt status mt: /dev/tape: No such device dcr1:/proc# ls -l /dev/tape lrwxrwxrwx 1 root root 8 2007-02-07 16:01 /dev/tape -> /dev/st0 dcr1:/proc# That mt status command will show the actual st0 status when things are working correctly. The No such device message is usually the second clue that we need to reboot - the first clue is usually that the backups didn't run.

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• Mirror a RAID0 volume

  - by Ghostrider

  I have two SSD running in RAID0. The capacity and speed are just great. I use Windows Home Server to do incremental daily backups. This is fine and well and I've successfully restored from these backups. However. When one of the disks physically died. I was stuck without a working system until the replacement arrives so that I can restore the array from backup. WHS restoration takes about 5 hours which basically means that I'm losing entire day for the process. Is it possible to set up kind of a recovery volume for the RAID array? Use a single mechanical HDD that would be updated with the exact clone of the RAID array on a daily basis. This way if the array goes offline for some reason, I can just boot from the mechanical HDD, lose some perf but will still be able to work. The machine in question runs Windows 7. Creating RAID01 is not an option because of the high price of the SSD and the fact that it still doesn't protect against failure of RAID controller. Is there any way it can be set up?

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

  - by Shadow00Caster

  I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

  Read the article

• USB To Serial under OpenSuse 11.3

  - by Exsisto

  I have a LogiLink USB-To-Serial adapter. This has the PL2303 chip inside. When I insert the device: [26064.927083] usb 7-1: new full speed USB device using uhci_hcd and address 9 [26065.076090] usb 7-1: New USB device found, idVendor=067b, idProduct=2303 [26065.076099] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [26065.076105] usb 7-1: Product: USB-Serial Controller [26065.076110] usb 7-1: Manufacturer: Prolific Technology Inc. [26065.079181] pl2303 7-1:1.0: pl2303 converter detected [26065.091296] usb 7-1: pl2303 converter now attached to ttyUSB0 So the device is recognized and the converter is attached to ttyUSB0. When I do screen /dev/ttyUSB0 9600 I get the error: bash: /dev/ttyUSB0: Permission denied So I went looking in the file permissions. ls -l from the /dev folder reports: crw-rw---- 1 root dialout 188, 0 2011-04-26 15:47 ttyUSB0 I added my user lars to the dialout group. When I use the commands groups under lars it shows that I'm in the group. Though I still recieve the permissions denied error, as lars, and as root. I'm trying to connect to a console cable to configure some Cisco switches. My OS is OpenSuse 11.3 x86_64 with kernel version 2.6.34.7-0.7-desktop.

  Read the article

• New SSD freezing on older motherboard (intel G31)

  - by DJM

  I have an ECS G31T-M motherboard running a Core2 Quad processor, 4gb RAM, Windows 7 32bit, Geforce 9600GT. Bought a Sandisk Extreme III 120GB (SDSSDX-120G-G25) and installed today. I'm outputting this from my 9600GT with included TV-out adapter to Component video (to my HDTV). This motherboard is SATA 2 and from what I can tell, SSDs run on the IDE controller and there is nothing fancy to set up advanced features of SSDs. I've noticed on other forums (but not verifying with ECS) this board does not support AHCI. I have two versions of Windows 7 installed on two drives, the SSD and an old 500G disc drive. When booted from my older 500G HDD, video plays fine on the HDTV. When booting the SSD windows 7 install, I am freezing constantly, as in, video plays OK for a minute, then picture freezes for 1-3 minutes (sometimes as audio continues playing) and returns for 20-30 seconds before doing the same thing again. Other tasks such as basic maneuvering through file folders seems to be no problem. Please help!! Do I need a new system for this thing to work, or could there be other fixes? I updated firmware to R201 to no avail. DJM

  Read the article

• help with xorg.conf: xrandr on one of two widescreen monitors; rhel5, kde, ATI Radeon X1300

  - by user35997

  Can anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel. Thanks1 My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "Multihead layout" Screen 0 "aticonfig-Screen[0]" 0 0 InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "off" Option "Clone" "on" EndSection Section "Files" EndSection Section "Module" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Dell 2407WFP (Digital)" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 76.0 Option "dpms" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "Videocard0" Driver "vesa" EndSection Section "Device" Identifier "Videocard1" Driver "vesa" VendorName "Videocard Vendor" BoardName "ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]" Driver "fglrx" Option "DesktopSetup" "horizontal" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Videocard1" Monitor "Monitor1" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]" Device "aticonfig-Device[0]" Monitor "aticonfig-Monitor[0]" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection

  Read the article

• Error 53 - The network path was not found.

  - by Jack

  I have a machine in my Active Directory Domain that I can no longer "net view" from other machines in the domain. This is a Windows XP Pro machine. It is hosting a VMWare virtual of my Domain Controller. If I attempt to net view [machine name] I get system error 53, The network path was not found. This is not a DNS issue, the same thing happens with the machine's IP. I don't think it's a firewall issue, I turned the firewall off on this machine. As I mentioned, it has worked in the past, and then stopped for no reason that I can see. I (intentionally) didn't change the software. I CAN get to the VMs hosted on this machine, can connect to their shares, net view them, etc. All other machines can see each other. In fact, the problem machine can see other machines and access their shares just fine. I tried removing the machine from the domain and re-adding it. I tried deleting the shares and recreating them. Not sure how to troubleshoot this any further. Any ideas?

  Read the article

• Dell Poweredge 1950 with Perc 5i keeps losing raid config -> "Foreign Configuration Found"

  - by nosage

  The quick and dirty: the machine is a Dell Poweredge 1950, dual xeon quad cores, 8GB of ram, 2 2TB seagate SATAs in (supposed to be raid1) using a Perc 5i raid card. They are hot-swappable with a back-plane. I can build the raid fine and after a little while an install of server 08 r2 will blue screen and restart. When it comes up the raid controller says "Foreign Configuration Found." When I go into the raid configuration panel there is no raid listed but I can import the "foreign config", and the OS will boot up fine, until it blue screens again after a little while. The issue is OS independent. I have tried swapping raid cards, swapping the RAM module on the raid card and swapping the raid battery, all to no avail. Its almost as if there is a loose connection from the raid card to the back plane and both of disks get lost and the raid card drops the config. But it sees the disks fine when it boots back up. The raid card uses a SCSI SAS cable to connect to the back-plane so I guess the next step is to replace that, but... then I might as well replace the back-plane with a SCSI SAS to sata breakout cable, but... then I need a way to power the disks. Sorry for the wall of txt but it would be great to get some thoughts from people who worked with perc raid cards or poweredge servers with this type of issue before. Ironically I want to get this system up and running so I can work on MCITP labs. Thank you for any/all help and feel free to ask questions!

  Read the article

• DNS Does Not Register at Off-site Locations

  - by Russ Warren

  First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

  Read the article

• Kerberos service on win2k dc will not start following disk failure

  - by iwilson68

  Hi, I have a win2k (mixed mode domain) with 4 DCS. One of these also acts an exchange 2000 server which uses 2 logical volumes from an MSA 2000 array. AD etc is stored on local drives. We experienced a problem last week when the raid array fell back to a redundant controller and this temporarily meant that the two logical drives were not visible to the server for around 5 minutes and a couple of reboots. The log records these Events as Type: Warning Event Source: Disk Event Category: None Event ID: 51 Date: 06/11/2009 Time: 11:46:23 User: N/A Computer: server1 Description: An error was detected on device \Device\Harddisk1\DR1 during a paging operation. Following these problems, the server “kerberos Key Distribution” service refuses to start with an “error.31 a device attached to the system is not functioning”. All other automatic start services (including net logon) are running and there are no DNS issues etc. All devices are also functioning but the two logical MSA disks are now numbered in the Windows Disk Management MMC as 2 and 4 and I suspect that they may have previously been identified as disks 1 & 2 and perhaps windows still sees this as an ongoing failure?? Replication has not been affected but obviously there are many audit failures in the security log relating to users and workstations presumably linked to the Kerberos issue. Attempting to manually start the kerberos service generates the following in the System Log. Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 09/11/2009 Time: 09:46:55 User: N/A Computer: Server1 Description: The Kerberos Key Distribution Center service terminated with the following error: A device attached to the system is not functioning. DCDIAG passes all tests except “Advertising” and “Services” which I believe relate directly to the failure of Kerberos only. Any advice would be appreciated.

  Read the article

• Picking a linux compatible motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• 1 document pending in printer queue in System Tray that won't go away

  - by White Phoenix

  Edit: I didn't want to do it, but I restarted my computer - cleared the problem right away. Though if I were running a Windows 2003/2008 server, I would hate to have to restart the domain controller just to get rid of this irritating problem. If I run into this problem again, I'm going to try that remove printer/reinstall printer thing. Thanks for your help @Psychogeek. Points for your attempt. Running Windows 7, 32-bit Professional. My printer is an HP OfficeJet Wireless 8500. It's connected to my network wirelessly through TCP/IP as a standalone device. I was having some print problems awhile back and had to do some print spooler stuff as part of my troubleshooting (stopping the Print Spooler service, clearing the print spooler files from C:\Windows\System32\spool\PRINTERS and then restarting the service). I've finally narrowed it down to it being application specific, so that's that. However, as a leftover from all that troubleshooting, my printer icon is stuck in the tray - when I mouseover the icon, Windows says that there is 1 document(s) pending for my username. However, when I open up that printer's queue, there's nothing in there. I restarted the Printer Spooler service and also checked C:\Windows\System32\spool\PRINTERS if there's anything in there - nothing. I did a quick Google search and an answer from one of those "reps" at the Microsoft Socialnet site says for me to uninstall and reinstall the printer. The funny thing is, when I send print jobs, they print just fine - that 1 mystery document stuck in queue isn't stopping anything from happening. Short of having to do that, are there any other quick troubleshooting steps I may be missing?

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• 403 Forbidden when Deploying asp.net 4.0 site to IIS 7

  - by Jordan

  So I have an EC2 instance running, the URL NoWeatherSurprises.com I have the DNS pointing there, and I set up a new site in IIS 7 and pointed it to a folder. I used Visual Studios Web Developer 2010 express to publish to this folder. It now has the binaries and such. However if I go to NoWeatherSurprises.com I get the welcome to IIS 7 screen. I'd expect to go to my application If I navigate to http://noweathersurprises.com/weather/ [weather was the folder I published to under wwwroot] I get a 403 forbidden. I have no idea why, I am guessing that it is trying to do a directory listing or something instead of launching my MVC Application. So 2 problems in summary. It is not pointing the domain to the folder directly and I need to add /weather I am getting a 403 forbidden instead of the results of my home controller with the index action. I am new to IIS 7, I had been using IIS 6 and had a lot less trouble setting it up, but I suspect that's my own fault and i am just missing something. Thanks in advance for any help

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Blender refuses to start

  - by Sekhemty

  I'm trying to run Blender under Linux, but I'm unable to do that, whenever I try I get some errors. I'm using Kubuntu 12.04 with KDE 4.11.1. This is my video card: ~$ lspci | grep VGA 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT] I used to have installed the fglrx proprietary Catalyst drivers, but lately they gave me some system-wide problems and I had to revert to the open source Mesa drivers (I don't think that these details are important, but just in case, the whole story is here). Whit the fglrx drivers Blender was running fine, but now, whenever I try to start it, I get this error message (some parts are in italian, but I think that they are easily understandable): ~$ blender connect failed: No such file or directory Writing: /tmp/blender.crash.txt Errore di segmentazione (core dump creato) The content of /tmp/blender.crash.txt is as follows: # Blender 2.68 (sub 5), Revision: 60150 # backtrace /usr/lib/blender/blender() [0x877a41f] [0xb7756400] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(_ZN4llvm3ARM8SPRClassC1Ev+0x15) [0xa8f4a9d5] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(+0x25ca48) [0xa8eefa48] /lib/ld-linux.so.2(+0xeeab) [0xb7765eab] /lib/ld-linux.so.2(+0xef94) [0xb7765f94] /lib/ld-linux.so.2(+0x12fa6) [0xb7769fa6] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/ld-linux.so.2(+0x127f4) [0xb77697f4] /lib/i386-linux-gnu/libdl.so.2(+0xbe9) [0xb4ff9be9] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/i386-linux-gnu/libdl.so.2(+0x133a) [0xb4ffa33a] /lib/i386-linux-gnu/libdl.so.2(dlopen+0x47) [0xb4ff9c97] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x3cbf0) [0xb7717bf0] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x4079d) [0xb771b79d] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x1a3aa) [0xb76f53aa] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(glXQueryVersion+0x2e) [0xb76f0cee] /usr/lib/blender/blender(_ZN15GHOST_WindowX11C1EP15GHOST_SystemX11P9_XDisplayRK10STR_Stringiijj18GHOST_TWindowStatei25GHOST_TDrawingContextTypebbt+0x11c) [0x8f54aec] /usr/lib/blender/blender(_ZN15GHOST_SystemX1112createWindowERK10STR_Stringiijj18GHOST_TWindowState25GHOST_TDrawingContextTypebbti+0xd7) [0x8f4f4a7] /usr/lib/blender/blender(GHOST_CreateWindow+0xb6) [0x8f4cf86] /usr/lib/blender/blender(wm_window_add_ghostwindows+0x205) [0x8799be5] /usr/lib/blender/blender(WM_check+0x50) [0x877b670] /usr/lib/blender/blender(wm_homefile_read+0x111) [0x87859f1] /usr/lib/blender/blender(WM_init+0xd2) [0x8787872] /usr/lib/blender/blender(main+0xe6e) [0x873848e] /lib/i386-linux-gnu/libc.so.6(__libc_start_main+0xf3) [0xb4e694d3] /usr/lib/blender/blender() [0x8778a99] The only thing that I can guess from this report is that the mesa drivers are somewhat involved, as I already suspected, but I don't have a clue on what I need to do to try to solve the issue.

  Read the article

• "The directory name is invalid" when trying to install drivers in Windows 7 via Device Manager

  - by Luke

  First off, this computer is not mine, it's a customer's system. Having said that... The hard drive was moved to a new motherboard, CPU, RAM combo, and booted up fine. Customer puts in driver CD, drivers won't load. He brings it into me. Under Device Manager for Windows 7 x64, I see lots of PCI to PCI bridge, one SMBus Controller, and about 20 Unknown Devices. Greeeeeat... So I start with the SMBus driver directly from the Asus website for the motherboard (P8H77-M Pro). If I install from the setup program, it tells me to reboot, then it starts the install. It gets half way through the setup, then fails (An unknown error occurred. Setup will exit). When I try to point to the folder from Device Manager, it starts copying files for the driver, even presents me with the proper name of the device, but says that an error has occurred there as well: The directory name is invalid. Doing some Googling, I saw that many people had this issue with Vista. K, Vista and 7 are similar, maybe the solutions are the same... But they aren't. I tried: Copying the entire driver folder and setup utility to the Program Files folder and running it / selecting it in DM Downloading another set of drivers in case this one is corrupt Disabling UAC Deleting and recreating the %WINDIR%\TEMP folder Removing all references to previous hardware that I could find, even in Device Manager's hidden mode So far, nothing has worked. A wipe and reload will be out of the question

  Read the article

• New router messed up server 2003 setup...

  - by Aceth

  Hey, We were sent a new 2wire router today configured it as best we can to match the old bt voyager. We've also got X static IP's. We've manage to get our webserver on one of the new IP's public facing. then we use a hardware firewall which is in a DMZ again with a different static IP. This firewall then is our gateway for our internal LAN. with a few servers etc. The problem we're having is only our PDC (primary Domain controller which has exchange 2003 on) can't ping externally even an external IP. We've connected laptops to the 2wire router and obtain a private ip 192.168.1.X and it works fine can ping etc. our other servers with an internal ip behind the firewall can ping out fine. We've connected to the firewalls logging console and the pings from the server are allowed through so its fine there. The server in question is a Windows server 2003 R2 Enterprise SP2 + Exchange 2003 Server doesn't have firewall turned on. it has static private IP .. gateway is pointing to the right one External Static IP is routing fine inwards We've ran out of ideas .. help??

  Read the article

< Previous Page | 303 304 305 306 307 308 309 310 311 312 313 314  | Next Page >