primary interop assembly - Page 308

Boot drive not found issue after cloning using Apricorn EZgig

- by TomWilsonFL

A couple days ago I cloned a drive for someone using the EZgig software. Usually this goes without a hitch, but this particular drive I was cloning is quite old. When I restarted with the new drive I received the typical bootable disk not found message, so I turned it off, messed with the BIOS, restarted and it came up fine. That night I was working remotely on the computer and had to restart it. It didn't come back up; not a good sign. When the user came to the computer in the morning it was giving the same message. I have found that to make the computer boot, all I have to do is go into the BIOS and "Load Defaults", then restart. It will boot and runs great. Any thoughts on what is causing this situation? Is it MBR corruption? Are some settings being saved in the CMOS? A couple points of mention: I have already attempted looking for a BIOS update for the computer, but the newest is already installed (from 2003). When the computer reboots it either shows "None" for Primary Master, or sometimes it will just not show anything. Thanks, Tom

Read the article

Ubuntu via Wubi refuses to show up in boot menu

- by Redandwhite

I'm in this strange situation: I have 3 partitions, one for Vista (C), one for Windows 7 (D), and one 10GB partition (E). At least that's how my original OEM Vista partition sees them. The primary OS that I boot into everyday is Windows 7. The situation is that for some reason it sees the Windows 7 partition (its own) as drive C, the 10GB one as (D) and the Vista one as (E). I've successfully used the Wubi installation before on Vista, but now it simply doesn't work. Ubuntu just does not show up in the boot menu, no matter what I try to do. I'm running out of ideas. I heard it doesn't really play well with Windows 7 either. I set it to Vista compatibility mode and that didn't work, I also tried installing it from Vista itself and that didn't work either for some reason. Any ideas what I should try? If anyone is about to suggest EasyBCD, please underline the command-line instructions I'm gonna need to follow. Thanks.

Read the article

openvpn port 53 bypasses allows restrictions ( find similar ports)

- by user181216

scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

Read the article

openvpn port 53 bypasses allows restrictions ( find similar ports)

- by user181216

scenario of wifi : i'm using wifi in hostel which having cyberoam firewall and all the computer which uses that access point. that access point have following configuration default gateway : 192.168.100.1 primary dns server : 192.168.100.1 here, when i try to open a website the cyberoam firewall redirects the page to a login page (with correct login information, we can browse internet else not), and also website access and bandwidth limitations. once i've heard about pd-proxy which finds open port and tunnels through a port ( usually udp 53). using pd-proxy with UDP 53 port, i can browse internet without login, even bandwidth limit is bypassed !!! and another software called openvpn with connecting openvpn server through udp port 53 i can browse internet without even login into the cyberoam. both of softwares uses port 53, specially openvpn with port 53, now i've a VPS server in which i can install openvpn server and connect through the VPS server to browse internet. i know why that is happening because with pinging on some website(eb. google.com) it returns it's ip address that means it allows dns queries without login. but the problem is there is already DNS service is running on the VPS server on port 53. and i can only use 53 port to bypass the limitations as i think. and i can not run openvpn service on my VPS server on port 53. so how to scan the wifi for vulnerable ports like 53 so that i can figure out the magic port and start a openvpn service on VPS on the same port. ( i want to scan similar vulnerable ports like 53 on cyberoam in which the traffic can be tunneled, not want to scan services running on ports). improvement of the question with retags and edits are always welcomed... NOTE : all these are for Educational purpose only, i'm curious about network related knowledge.....

Read the article

RPC Server Unavailable on Hyper-V cluster when moving resources after the host adapter has failed

- by Doug Luxem

On a Windows 2008 R2 SP1 cluster running Hyper-V, a lost network connectivity on the primary host interface. The interface was rapidly flapping up and down, and this was later determined to be caused by a faulty switch port. As this was a clustered server, the host interface was not fault tolerant (seeing as how the whole server was fault tolerant), so connectivity to the host was going up and down. The Hyper-V guests were completely unaffected by the network outage as they used a dedicated trunk on the server separate from the host interface. Additionally, dedicated interfaces for the cluster and live migration networks were fine. In order to diagnose the server, I tried to move all resources (Hyper-V Guests) to other nodes through Failover Cluster Manager. These moves failed with an error RPC Server Unavailable. The only way to move resources was by shutting down the guests, stopping the cluster service on the Node A, allowing other nodes to take ownership of the resources, and restarting the guests. A few other notes: All nodes have Client for MS Networks and File & Printer Sharing enabled on the Cluster and LM networks. Node A was accessible over cluster and LM networks from other nodes (these are private, cluster-only networks); pingable, CIFs, etc. Accessing \\NODEA is done over the Host adapters, as you would expect in this case and is the reason for the RPC Server Unavailable error with that adapter being down. My questions here are - Is there a way to still use Live Migration in a failure scenario such as this to prevent shutting down the Hyper-V guests? How can the network be reconfigured in the future so that the cluster service attempts to use the cluster and/or live migration networks to issue the RPC requests?

Read the article

Configure static IPv6 on Ubuntu

- by Charles Offenbacher

I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

Read the article

How to find the next generated value for a auto-increment column?

- by Tim Büthe

I face some trouble with IBM DB2's auto-increment columns. At first, all my columns were defined as GENERATED ALWAYS, but since I had trouble with this when using the "db2 import ..." command, I changed them to GENERATED BY DEFAULT. This is necessary, sinceI need the IDs to be consistent, because other tables reference them. So using "db2 import ... modified by identityignore ..." isn't an option. When I now import data, the IDs are inserted correctly, but everytime I do this, I have to remember to set a new start for the auto-increment column by getting the highest Id+1 and alter the column like this: SELECT MAX(mycolumn)+ 1 FROM mytable; ALTER TABLE mytable ALTER COLUMN mycolumn RESTART WITH <above_result>; If I forget this, an Insert-Statement will fail with an duplicate PK error, since the auto-increment column is the primary key. So my question is: Is there a way to find the next value for an auto-increment column, so I could write Statements that would check, if this value is less then the SELECT MAX and needs to be set? Or: Isn't this whole thing as complicated as it seems to me? Could I somehow import data, preserving the IDs and have the auto-increment column still working as expected?

Read the article

SBS2011 Standard DNS suddenly not resolving some domains

- by Matt

Suddenly today I am unable to resolve common domains like serverfault.com, facebook.com; but other domains like google.com, cnn.com work fine. This is on a client machine (Win7 Pro) connected to an SBS2011 Standard domain. The only DNS server is the SBS2011 server. The same domains work fine on all client PCs I have tried, and the same ones do not work. Using nslookup, I get 'no such domain' errors for facebook.com, and the correct DNS entries for the ones that do work. When I add Google's Public DNS to my client PC as a backup (primary = local SBS server, secondary = 8.8.8.8), everything works fine for my client PC, but querying from the SBS server directly or from other client PCs are broken (so I don't believe it's a firewall issue). My main question is how can I see what servers the SBS2011 server queries if it doesn't know about a domain? There is nothing in our firewall logs that say it blocked any DNS-based packets, but I also wanted to query based on the IP/FQDN on the servers that the SBS server was likely to contact to find out about facebook.com for example. Update 23/05/2012: It appears DNS is working again this morning for the affected websites. Both the DC on its own and all client PCs can once again access the websites that were not loading last night, as well as the websites that were working. I haven't changed anything overnight, so it appears that there was some kind of temporary glitch, but I can't understand what would have caused it on the network.

Read the article

Nginx, as reverse proxy, could not proxy_pass to a domain pointing to the local JBOSS

- by larryzhao

My environment is Ubuntu 12.04, Nginx 1.20, and Torquebox 2.0.3 which is actually JBoss AS 7. I have two app deployed on Torquebox, it listens to 8080 and have different hostnames, app1.mydomain.com and app2.mydomain.com. I added 127.0.0.1 app1.mydomain.com and 127.0.0.1 app2.mydomain.com in /etc/hosts then I curl app1.mydomain.com:8080 and curl app2.mydomain.com:8080 both have correct return. Then I go to my nginx. I would like nginx to pass the visit to www.app1.com to app1.mydomain.com:8080, so I have the following configuration: # primary server - proxypass to torquebox server { listen 80; server_name www.app1.com; access_log off; error_log off; # proxy to Torquebox location / { proxy_pass http://app1.mydomain:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_max_temp_file_size 0; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } } But it doesn't work. curl www.app1.com returns nothing. And if I visit www.app1.com in Safari, the http return code is 404. I don't know why, need help.

Read the article

Almost All Xenserver Logical Volumes Disappeared - Recovery?

- by Alex

We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

Read the article

yum fails installing php53-devel.x86_64

- by coding_hero

I need to recompile php on a Fedora server because I need to use the --enable-zip flag. When trying to install the devel package, I get the following message. This is after a 'yum clean all': yum install php53-devel.x86_64 Loaded plugins: rhnplugin, security rhel-x86_64-server-5 | 1.4 kB 00:00 rhel-x86_64-server-5/primary | 4.9 MB 00:00 rhel-x86_64-server-5 14161/14161 Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php53-devel.x86_64 0:5.3.3-13.el5_8 set to be updated --> Processing Dependency: php53 = 5.3.3-13.el5_8 for package: php53-devel --> Finished Dependency Resolution php53-devel-5.3.3-13.el5_8.x86_64 from rhel-x86_64-server-5 has depsolving problems --> Missing Dependency: php53 = 5.3.3-13.el5_8 is needed by package php53-devel-5.3.3-13.el5_8.x86_64 (rhel-x86_64-server-5) Error: Missing Dependency: php53 = 5.3.3-13.el5_8 is needed by package php53-devel-5.3.3-13.el5_8.x86_64 (rhel-x86_64-server-5) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest Output of 'yum repolist': # yum repolist Loaded plugins: rhnplugin, security repo id repo name status rhel-x86_64-server-5 Red Hat Enterprise Linux (v. 5 for 64-bit x86_64) enabled: 14,161 repolist: 14,161

Read the article

How can I create a VLAN on my extreme switch for a seperate subnet/domain?

- by drpcken

I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

Read the article

Setting up /etc/network/interface file for KVM ubuntu 10.10

- by Charles Thornton

I am trying to setup KVM on Unbuntu 10.10 IFCONFIG DUMP: hydra(~}$ifconfig eth0 Link encap:Ethernet HWaddr 00:1b:fc:cb:77:eb inet addr:172.20.20.3 Bcast:172.20.20.255 Mask:255.255.255.0 inet6 addr: fe80::21b:fcff:fecb:77eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1345 errors:0 dropped:0 overruns:0 frame:0 TX packets:1541 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:820414 (820.4 KB) TX bytes:317708 (317.7 KB) Interrupt:23 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) virbr0 Link encap:Ethernet HWaddr 0a:1e:fb:b4:77:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 inet6 addr: fe80::81e:fbff:feb4:7784/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:8934 (8.9 KB) hydra(~}$ QUESTION:: How should /etc/network/interfaces be setup?? The following attempt just kills my internet connection! --------- /etc/network/interfaces ------------- # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 172.20.20.3 netmask 255.255.255.0 network 172.20.20.0 broadcast 172.20.20.255 gateway 172.20.20.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off What am I doing wrong????

Read the article

How to keep subtree removal (`rm -rf`) from starving other processes for Disk I/O?

- by David Eyk

We have a very large (multi-GB) Nginx cache directory for a busy site, which we occasionally need to clear all at once. I've solved this in the past by moving the cache folder to a new path, making a new cache folder at the old path, and then rm -rfing the old cache folder. Lately, however, when I need to clear the cache on a busy morning, the I/O from rm -rf is starving my server processes of disk access, as both Nginx and the server it fronts for are read-intensive. I can watch the load average climb while the CPUs sit idle and rm -rf takes 98-99% of Disk IO in iotop. I've tried ionice -c 3 when invoking rm, but it seems to have no appreciable effect on the observed behavior. Is there any way to tame rm -rf to share the disk more? Do I need to use a different technique that will take its cues from ionice? Update: The filesystem in question is an AWS EC2 instance store (the primary disk is EBS). The /etc/fstab entry looks like this: /dev/xvdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2

Read the article

Windows Not Honoring DHCP Scope

- by jerhinesmith

Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

Read the article

Puzzling TCP performance over 3G / UMTS

- by lemonsqueeze

I'm using 3G as my primary internet connection, and TCP over this thing is getting more puzzling every day. For example: Downloading from kernel.org is crazy fast: $wget http://www.kernel.org/pub/linux/kernel/v3.0/linux-3.6.8.tar.bz2 increases to ~500kB/s after a few secs ! Some servers are incredibly slow, for instance www.graphic-pc.com:Same thing, downloading a big file with wget it starts at ~30kB/s for a split second, then collapses to 5-10k or even worse. Web browsing is decent but somewhat unreliable. Randomly, a page will take really long to load or even fail to load, but a reload can succeed almost immediately. Now, by chance i started playing with OpenVPN over UDP on top of the 3G connection, and OMG suddenly everything's extremely fast !Same www.graphic-pc.com now shoots at 100-200kB/s ! What's going on here ??? How come it is so much better with the VPN than without ?? And why does graphic-pc.com crawl when kernel.org flies ?Something to do with my tcp stack (or the server), or some buggy router in between ?? Notes: Setup is laptop running Ubuntu Lucid and a Huawei 3G dongle (So direct pppd connection). I can reproduce this pretty much any time during the day and I'm not moving, so it's clearly not cell environment or internet congestion. (although kernel.org without VPN sometimes does worse in the evening, 60kB or so - but still 500kB with VPN !) For 2) wireshark shows retransmitted packets, dup ack's, even out of order sometimes. I've tried playing with different /proc/sys/net/ipv4 parameters (tcp_rmem, window_scaling, tcp_congestion...) doesn't seem to make a difference. Update: Tried under windows 7 (no VPN) with some interesting results: tcp settings : default tcp_optimizer kernel.org : 10 kB/s 20 kB/s graphic-pc.com: 8 kB/s 70 kB/s ! tcp_optimizer turned on ctcp among other things. Have to check what os graphic-pc.com is running, my bet is linux's tcp_westwood and ms ctcp don't mix well here...

Read the article

Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

- by Magdy Roshdy

I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

Read the article

Writing xml with powershell

- by alex

i have a script that get all the info i need about my SharePoint farm : [System.Reflection.Assembly]::LoadWithPartialName("Microsoft.SharePoint") > $null $farm = [Microsoft.SharePoint.Administration.SPFarm]::Local $websvcs = $farm.Services | where -FilterScript {$_.GetType() -eq [Microsoft.SharePoint.Administration.SPWebService]} $webapps = @() foreach ($websvc in $websvcs) { write-output "Web Applications" write-output "" foreach ($webapp in $websvc.WebApplications) { write-output "Webapp Name -->"$webapp.Name write-output "" write-output "Site Collections" write-output "" foreach ($site in $webapp.Sites) { write-output "Site URL --> -->" $site.URL write-output "" write-output "Websites" write-output "" foreach ($web in $site.AllWebs) { write-output "Web URL --> --> -->" $web.URL write-output "" write-output "Lists" write-output "" foreach ($list in $web.Lists) { write-output "List Title --> --> --> -->" $list.Title write-output "" } foreach ($group in $web.Groups) { write-output "Group Name --> --> --> -->" $group.Name write-output "" foreach ($user in $group.Users) { write-output "User Name --> --> --> -->" $user.Name write-output "" } } } } } } i want to make the output to an XML file and then connect the xml file to HTML and make a site of it for manager use how can i do it ? thanks for the help !

Read the article

Using the full width of an Excel chart with two Y-axes

- by Jørn Schou-Rode

I am trying to create a line chart in MicrosoftExcel 2007 with two data series, each with their own Y-axis. First, I create a simple chart by selecting the two data series, and choosing Insert > Charts > Line from the Ribbon. I now see the following chart in my workbook: I then continue my quest by right clicking one of the data series (lines) and choosing Format data series > Series Options > Secondary Axis. My chart is now looks like this: This is almost what I want. I did not expect to see the gap between the last X-axis tick point (x = 5) and the secondary (right most) Y-axis. Why does Excel introduce this gap? Is there anything I can do to avoid it? I have tried right clicking the X-axis and seleting Format Axis > Axis Options > Position Axis: Between tick marks, but that only introduces a similar gap on by the primary (left most) Y-axis.

Read the article

Disk doesn't contain a valid partition table

- by Jeevan Dongre

I was running a m1.small instance ec2 ubuntu instance. I was running out of disk space, so I upgraded my instance to medium. When I upgraded I actually got 429.5 GB of space and after that I added 10 gb of volume too. When I run the "sudo fdisk -l" command I got this results. Disk /dev/sda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 429.5 GB, 429461078016 bytes 255 heads, 63 sectors/track, 52212 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda2 doesn't contain a valid partition table Disk /dev/sdf: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 sda1 is the primary parition and sda2 is what I got added upgrading my system to medium. But the problem persists, I am not able to pull the code from git, it is giving me this error. remote: Counting objects: 409, done. remote: Compressing objects: 100% (236/236), done. fatal: write error: No space left on device fatal: index-pack failed

Read the article

"Error 53" with local LAN machines after VPN session on server

- by tim11g

I have a Windows 2000 server with a Windows 7 client that occasionally gets "error 53" when accessing the server by name (net view \\server). It still works by IP address (net view \\192.168.0.1). The server's primary IP address (as shown in "routing and remote access" as "Gigabit Ethernet" is 192.168.0.1. There is also a secondary IP address shown as "Internal" which is 192.168.0.50 The server also supports VPN. When a VPN user connects, it gets an address in the range of 192.168.0.51 to .59. Normally (when there is no error), when the local LAN client runs "ping server", it resolves to 192.168.0.1. When the Error 53 problem happens, "ping server" resolves to 192.168.0.50. This problem seems to be related to when a user connects or has recently connected to the server VPN. Is there some connection between the VPN services on the server and the DNS services on the server that could cause a local LAN client to become confused about which IP address to use for the server? Or is there a misconfiguration in the VPN or DNS?

Read the article

Discrepancy in file size on disk and ls output

- by smokinguns

I have a script that checks for gzipped file sizes greater than 1MB and outputs files along with their sizes as a report. This is the code: myReport=`ls -ltrh "$somePath" | egrep '\.gz$' | awk '{print $9,"=>",$5}'` # Count files that exceed 1MB oversizeFiles=`find "$somePath" -maxdepth 1 -size +1M -iname "*.gz" -print0 | xargs -0 ls -lh | wc -l` if [ $oversizeFiles -eq 0 ];then status="PASS" else status="CHECK FAILED. FOUND FILES GREATER THAN 1MB" fi echo -e $status"\n"$myReport The problem is that ls command outputs the files sizes as 1.0MB in the report but the status is "FAIL" as "$oversizeFiles" variable's value is 2. I checked the file sizes on disk and 2 files are 1.1MB. Why this discrepancy? How should I modify the script so that I can generate an accurate report? BTW, I'm on a Mac. Here is what man page for "find" says on my Mac OSX: -size n[ckMGTP] True if the file's size, rounded up, in 512-byte blocks is n. If n is followed by a c,then the primary is true if the file's size is n bytes (characters). Similarly if n is followed by a scale indicator then the file's size is compared to n scaled as: k kilobytes (1024 bytes) M megabytes (1024 kilobytes) G gigabytes (1024 megabytes) T terabytes (1024 gigabytes) P petabytes (1024 terabytes)

Read the article

Is there a standard method for assigning nameservers to servers in a Windows domain?

- by HopelessN00b

As the title asks, I'm wondering if there's any standard or "best practice" for how to actually assign nameservers (DNS) and manage the nameserver configuration for client servers on a Windows domain. I'm talking about the setting circled in the below image, in case the language of the question is not clear enough: This is for a large, multi-site environment, where ideally/hopefully all servers point at their site's Domain Controller as the primary DNS server, and a DNS server at a different site as the secondary DNS server. For simplicity's sake, we can say that the secondary server would be the Domain Controller at the home site for everyone, and there are no tertiary DNS servers (even though that's not actually the case). Try as I might, I can't seem to find a GPO setting for this (at least on FL 2003 R2, the Computer Configuration - Administrative Templates - Network - DNS Client - DNS Servers GPO is Supported on: Windows XP Professional only), and I find it rather hard to believe that the "best"/"standard" solution would therefore be either scripting up something to apply the DNS settings per site, or using a DHCP server to push those configurations out to the other servers via the DHCP Scope Options. So, is there a standard way of managing this configuration? (That's hopefully not "a script" or "DHCP Scope Option.)

Read the article

Can't start Windows 7 after cloning HDD

- by Paul

Brief description: cloned HDD1 - HDD2 HDD1 partition 1 boots HDD1 partition 2 boots HDD2 partition 1 boots HDD2 partition 2 doesn't boot Windows, but is bootable in general Now verbosely: In all the cases computer is the same. I have two Windows 7 installations on HDD1 - both are booting fine. I choose between them using standard Windows 7 boot loader menu. Technically there are 4 partitions: 100 MB Boot loader partition (active), Windows 7 copy 1 (25 GB), Windows 7 copy 2 (150 GB) and Working partition. All are primary. In past few days I tried to clone the whole HDD1 to HDD2 of the same size (but 2,5 inch form factor) as is using Minitool Partition wizard. Everything has been copied, all files are accessible, no faults in file system structure, even boot loader wasn't damaged and I hadn't to repair it. But I can boot only first installation of Windows 7 (it boots without issues). When I choose the second installation, I get immediately a completely black screen without any texts, cursors and other data. HDD isn't accessed after that. This black screen is sensitive to Ctrl-Alt-Delete which causes computer reboot. I did some experimenting: Installed Windows 7 to that partition - it booted fine. Then I renamed "Windows" to "Windows.old" and copied Windows directory from HDD1 as it was, using Far Manager, and got the same troubles - black screen. (Of course I performed renaming and copying from other copy of Windows). So, it seems that problems are inside this installation of Windows, somewhere in its files.

Search Results

Search found 9894 results on 396 pages for 'primary interop assembly'.

Page 308/396 | < Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315 | Next Page >

- by TomWilsonFL

- by Redandwhite

- by user181216

- by user181216

- by Doug Luxem

- by Charles Offenbacher

- by Tim Büthe

- by Matt

- by larryzhao

- by Alex

- by coding_hero

- by Chris Driver

- by drpcken

- by Charles Thornton

- by David Eyk

- by jerhinesmith

- by lemonsqueeze

- by Magdy Roshdy

- by alex

- by Jørn Schou-Rode

- by Jeevan Dongre

- by tim11g

- by smokinguns

- by HopelessN00b

- by Paul

< Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315 | Next Page >