Search Results

Search found 2353 results on 95 pages for 'serial communications'.

Page 31/95 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Error message when running OpenGL programs with bumblebee

  - by user170860

  X Error of failed request: BadDrawable (invalid Pixmap or Window parameter) Major opcode of failed request: 152 (DRI2) Minor opcode of failed request: 8 (DRI2SwapBuffers ) Resource id in failed request: 0x4200005 Serial number of failed request: 2166 Current serial number in output stream: 2167 primus: warning: timeout waiting for display worker Segmentation fault (core dumped) I don't get this on all OGL programs, but only particularly GPU intense ones. Also, I only get this using primusrun. optirun gives the same error no matter what I run: [VGL] NOTICE: Pixel format of 2D X server does not match pixel format of [VGL] Pbuffer. Disabling PBO readback. I don't know what either of these mean. Neither of them stop the programs from running, but I'd like to fix the problem if there is one. Also, I prefer to use primusrun because it is faster and it does a better job with vertical sync, however, it only supports OGL 4.2. This isn't a big issue because the programs I write are forward compatible, but it still seems odd to me. So basically I'd just like it if someone could explain to me what is happening and if there is something I can do about it. Thanks.

  Read the article

• An Oracle Exastack Recap

  - by Kristin Rose

  For those ISVs and OEMs who tuned into Oracle’s FY13 Partner Kickoff, thank you! It was with your participation and presence that helped make this year’s show another great success. The OPN Communications team was lucky enough to get a chance to sit down with Chris Baker, Oracle SVP of Worldwide ISV, OEM & Java, all the way from London, as he recapped the achievements that were seen over the past year with the Oracle Exastack Program. Be sure to watch his short video below: Here are some highlights: 1000 “Readies”- Those partners that are ready to use the latest version of our products Over 100 partners that are ready to use Oracle Exastack,  Oracle Exadata Database Machine, and Oracle Exalogic Elastic Cloud New Oracle Exalytics machine for analysis In less than one year, more than 100 ISV applications have achieved an Oracle Exastack Ready status and more than 35 ISV applications have achieved Oracle Exastack Optimized status. These partners can be found by Oracle customers listed in the Oracle Solutions Catalog.Demonstrating to customers that their solutions are tuned to deliver optimum speed, scalability and reliability on Oracle Engineered Systems, Oracle partners are rapidly achieving Oracle Exastack Optimized certification. Read the press release here. By simplifying your company’s architecture with the Oracle Exastack program, both ISV’s and OEMs are able to better concentrate on their application and deliver enhanced benefits to their customers.Cheers!The OPN Communications Team

  Read the article

• Unity 3D does not work on Dell system with a AMD Radeon HD 6470M

  - by VeeKay

  I am running 64 bit Ubuntu on Dell with 1GB graphic card. I login with "Ubuntu" hoping to see Unity 3d but it doesn't. Unity 2D runs instead. when I type in echo "$DESKTOP_SESSION" it confirms the Unity-2D. I've checked the System info that shows like : The graphics row shows itself as empty. SO I've presumed that the graphic drivers aren't detected and hence I went to Unity- Additional Drivers and installed the fglrx driver that the UI has suggested. Even after installing so, the graphics part in System info details shows nothing and still Unity 2D runs in spite of all the effort. Please help! How can I get my Unity 3D back? Hardware Info Video Card : AMD Radeon™ HD 6470M - 1GB (For ICC) RAM : 6GB (1 X 2GB + 1 X 4GB) 2 DIMM DDR3 1333Mhz OS : 64 bit Ubuntu 11.10 Edit : Output for /usr/lib/nux/unity_support_test -p X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 155 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 21 Current serial number in output stream: 21

  Read the article

• Why is wireless slow with Atheros AR9285?

  - by Luke

  I know there are many posts like this, however none of the fixes I have found have worked. I had the issue on 11.04, and after having no luck fixing it decided to try 12.04 however this has not fixed the problem. I'm using a Lenovo IdeaPad, the network card is a Atheros Communications AR9285. edit add outputs: sudo iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"NETGEAR-PLOW" Mode:Managed Frequency:2.437 GHz Access Point: E0:91:F5:7D:1B:BA Bit Rate=65 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:77 Invalid misc:63 Missed beacon:0 eth0 no wireless extensions. lspci -nnk | grep -iA2 net 06:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Lenovo Device [17aa:30a1] Kernel driver in use: ath9k -- 07:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 Thanks

  Read the article

• More information about worldwide nodes how to get?

  - by Aubergine

  The context: Six hosts across worldwide were traced over week from UK. Ten thousands of lines to be parsed and analysed. And then I try to find any clue of geographical information and path - from where it jumps where. Then after Austria or Germany(each time different) I have mysterious 62.208.72.6 which in GEO LOC gives me Falklands Islands (which is where my target host is by the way, but before target host I still have 5 other nodes) Then I do whois for this 62.208.72.6 route: 62.208.0.0/16 descr: DE-ECRC-62-208-0-0 origin: AS1273 mnt-by: CW-EUROPE-GSOC source: RIPE # Filtered Why it says Europe now? How to understand this enigma code? I want to confirm more or less whether this is in europe or in falkland islands? But it can't be in FK yet as after next two hosts I get New York? Could you also tell me what does this CW-EUROPE-GSOC abbreviation means. (To preserve your sanity better not google, unless you already know it :-D) And the actual whois for the destination/target host, which completely destroys my head: route: 195.248.193.0/24 descr: HORIZON descr: Cable and Wireless Falkland Islands descr: Via Cable and Wireless Communications UK origin: AS5551 mnt-by: AS5551-MNT source: RIPE # Filtered How is it Via Cable and Wireless Communications UK if two nodes before I was in New York? Thank you guys,

  Read the article

• USB device is recognized but has no address

  - by SeanMG

  Good day folks, I'm trying to use a USRP1 with GNURadio if anyone knows what any of that is. I am running Ubuntu on a Windows 7 machine via VMware player. When I connect this USRP1 via USB 2.0 drive to Windows 7 it is recognized as Ettus Research LLC USRP1... When I connect the device to Ubuntu through VMware, it shows: usb device fffe:0002 on my removable devices. When I run lsusb I receive the following: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub Bus 001 Device 004: ID fffe:0002 When I run this program that comes with the USRP driver... uhd_find_devices I receive: -------------------------------------------------- -- UHD Device 0 -------------------------------------------------- Device Address: type: usrp1 name: serial: 00000000 So when I run this program, it does recognize the fact that this device is connected. However, the device has no address, no name, and has a null serial. I need to know the device address so I can run more programs in GNURadio. Does anyone know what the problem is here? Thanks!

  Read the article

• X Error of failed request: BadMatch [migrated]

  - by Andrew Grabko

  I'm trying to execute some "hello world" opengl code: #include <GL/freeglut.h> void displayCall() { glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); glEnable(GL_DEPTH_TEST); ... Some more code here glutSwapBuffers(); } int main(int argc, char *argv[]) { glutInit(&argc, argv); glutInitDisplayMode(GLUT_RGB | GLUT_DOUBLE | GLUT_DEPTH); glutInitWindowSize(500, 500); glutInitWindowPosition(300, 200); glutInitContextVersion(4, 2); glutInitContextFlags(GLUT_FORWARD_COMPATIBLE); glutCreateWindow("Hello World!"); glutDisplayFunc(displayCall); glutMainLoop(); return 0; } As a result I get: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 128 (GLX) Minor opcode of failed request: 34 () Serial number of failed request: 39 Current serial number in output stream: 40 Here is the stack trace: fghCreateNewContext() at freeglut_window.c:737 0x7ffff7bbaa81 fgOpenWindow() at freeglut_window.c:878 0x7ffff7bbb2fb fgCreateWindow() at freeglut_structure.c:106 0x7ffff7bb9d86 glutCreateWindow() at freeglut_window.c:1,183 0x7ffff7bbb4f2 main() at AlphaTest.cpp:51 0x4007df Here is the last piece of code, after witch the program crashes: createContextAttribs = (CreateContextAttribsProc) fghGetProcAddress("glXCreateContextAttribsARB" ); if ( createContextAttribs == NULL ) { fgError( "glXCreateContextAttribsARB not found" ); } context = createContextAttribs( dpy, config, share_list, direct, attributes ); "glXCreateContextAttribsARB" address is obtained successfully, but the program crashes on its invocation. If I specify OpenGL version less than 4.2 in "glutInitContextVersion()" program runs without errors. Here is my glxinfo's OpelGL version: OpenGL version string: 4.2.0 NVIDIA 285.05.09 I would be very appreciate any further ideas.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Need to re-build an application - how?

  - by Tom

  For our main system, we have a small monitor application that sits outside our network and periodically tries to log in to verify the system still works. We have a problem with the monitor though in that the communications component set (Asta 3 inside Delphi applications) doesn't always connect through. Overall, I'd say it's about 95% reliable, but that other 5% kills the monitor since it will try to log in and hang on the connection attempt (no timeout in the component). This really isn't an issue on the client side of the system since the clients don't disconnect and reconnect repeatedly on the same application instance, but I need a way to make sure the monitor stays up and continues working even when the component fails on a run. I have a few ideas as to which way to have the program run, the main idea being to put the communications inside a threaded data module so that if one thread crashes then another thread can test later and the program keep going. Does this sound like a valid way to go? Any other ideas how to ensure a reliable monitoring application with a less than 100% reliable component? Thanks. P.S. Not sure these tags are the most appropriate. Tried including "system-reliability" as one, but not high enough rep to create.

  Read the article

• Unable to mount an LVM Hard-drive after upgrade

  - by Bruce Staples

  I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• How to add display resolution fo an LCD in Ubuntu 12.04? xrandr problem

  - by SeregaI

  I am fresh for Ubuntu and Linux in general. I have installed Ubuntu 12.04 and stuck trying to setup correct resolution for my LCD display. The native resolution for the LCD is 1920x1080 here is the output from xrandr: $xrandr Screen 0: minimum 320 x 200, current 1280 x 720, maximum 4096 x 4096 LVDS1 connected 1280x720+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1280x720 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) Then I create new modeline: $ cvt 1920 1080 60 1920x1080 59.96 Hz (CVT 2.07M9) hsync: 67.16 kHz; pclk: 173.00 MHz Modeline "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync So far so good. then I create new mode using xrandr: $ xrandr --newmode "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync But for some reason that new mode was created for VGA (VGA1) output instead of LCD output (LVDS1): $ xrandr Screen 0: minimum 320 x 200, current 1280 x 720, maximum 4096 x 4096 LVDS1 connected 1280x720+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1280x720 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) 1920x1080_60.00 (0xbc) 173.0MHz <---------- ????!!!!!! h: width 1920 start 2048 end 2248 total 2576 skew 0 clock 67.2KHz v: height 1080 start 1083 end 1088 total 1120 clock 60.0Hz So, if I try to add mode to LVDS1, I get an error: $ xrandr --addmode LVDS1 "1920x1080_60.00" X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 149 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 25 Current serial number in output stream: 26 Adding that new mode to VGA1 works fine, but I don't use that VGA1 output.

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Dual monitor display 12.04?

  - by MrMonty

  I have 2 beautiful 27" asus monitors. I started trying out Ubuntu 12.04 and now only one works and thats vga .. Any help here cause I'm stumped. I have a bfg tech nivida Geforce 8800 gt 512mb and I'm trying to fix this. Getting this error Wen i try to configure the xorg file Failed to set MetaMode (1) 'DFP-0: 1280x1024 @1280x1024 +0+0, DFP-1: 1280x1024 @1280x1024 +1280+0' (Mode 2560x1024, id: 50) on X screen 0. ........................................................................................... This is the xorg.conf ....................................................... nvidia-settings: X configuration file generated by nvidia-settings nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" Removed Option "Xinerama" "1" Removed Option "Xinerama" "0" Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputClass" Identifier "Mouse Remap" MatchProduct "Saitek Cyborg R.A.T.7 Mouse" MatchDevicePath "/dev/input/event*" Option "ButtonMapping" "1 2 3 4 5 6 7 8 9 0 0 0 0 0 0" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Removed Option "TwinView" "1" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection FILE ^^^^

  Read the article

• how to setup duel monitors an xorg.conf

  - by MrMonty

  # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" # Removed Option "Xinerama" "1" # Removed Option "Xinerama" "0" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" # Removed Option "TwinView" "1" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection thats my file!

  Read the article

• Browser automatically refreshes and Home folder window opens

  - by Vikash

  I am facing a very strange problem. Out of the blue, my browser starts refreshing itself infinitely. My first guess was firefox is messing up. I installed chrome. But, it happens in chrome as well. Other than that, sometimes my home folder automatically opens and keep opening itself infinitely. My next guess was Mouse is faulty. Replace the mouse - but same things. This happens even if I remove my keyboard. What can be the reason? This started happening after I installed Ubuntu 10.10 few days back. Earlier on windows, everything was working fine. So, I am a bit skeptical to assume that this is a hardware fault. How to fix this problem? UPDATE: xev gives this kind of result: KeyPress event, serial 36, synthetic NO, window 0x4200001, root 0xb8, subw 0x0, time 29897358, (237,791), root:(1252,842), state 0x10, keycode 65 (keysym 0x20, space), same_screen YES, XLookupString gives 1 bytes: (20) " " XmbLookupString gives 1 bytes: (20) " " XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4200001, root 0xb8, subw 0x0, time 29897603, (237,791), root:(1252,842), state 0x10, keycode 65 (keysym 0x20, space), same_screen YES, XLookupString gives 1 bytes: (20) " " XFilterEvent returns: False

  Read the article

• how can i find my usb2rs232 driver

  - by mefmef

  i have a device that is correctly connected to my PC . but i could not see it in /dev . what does it means? is it because of not installing my drive? $ /dev ls before connecting my device: agpgart mei sda1 tty28 tty59 ttyS30 autofs mem sda2 tty29 tty6 ttyS31 block net sda5 tty3 tty60 ttyS4 bsg network_latency sda6 tty30 tty61 ttyS5 btrfs-control network_throughput serial tty31 tty62 ttyS6 bus null sg0 tty32 tty63 ttyS7 char oldmem shm tty33 tty7 ttyS8 console parport0 snapshot tty34 tty8 ttyS9 core port snd tty35 tty9 ttyUSB0 cpu ppp stderr tty36 ttyprintk uinput cpu_dma_latency psaux stdin tty37 ttyS0 urandom disk ptmx stdout tty38 ttyS1 usbmon0 dri pts tty tty39 ttyS10 usbmon1 ecryptfs ram0 tty0 tty4 ttyS11 usbmon2 fb0 ram1 tty1 tty40 ttyS12 vcs fd ram10 tty10 tty41 ttyS13 vcs1 full ram11 tty11 tty42 ttyS14 vcs2 fuse ram12 tty12 tty43 ttyS15 vcs3 hidraw0 ram13 tty13 tty44 ttyS16 vcs4 hpet ram14 tty14 tty45 ttyS17 vcs5 input ram15 tty15 tty46 ttyS18 vcs6 kmsg ram2 tty16 tty47 ttyS19 vcsa log ram3 tty17 tty48 ttyS2 vcsa1 loop0 ram4 tty18 tty49 ttyS20 vcsa2 loop1 ram5 tty19 tty5 ttyS21 vcsa3 loop2 ram6 tty2 tty50 ttyS22 vcsa4 loop3 ram7 tty20 tty51 ttyS23 vcsa5 loop4 ram8 tty21 tty52 ttyS24 vcsa6 loop5 ram9 tty22 tty53 ttyS25 vga_arbiter loop6 random tty23 tty54 ttyS26 zero loop7 rfkill tty24 tty55 ttyS27 lp0 rtc tty25 tty56 ttyS28 mapper rtc0 tty26 tty57 ttyS29 mcelog sda tty27 tty58 ttyS3 $ /dev ls after connecting my device: agpgart mei sda1 tty28 tty59 ttyS30 autofs mem sda2 tty29 tty6 ttyS31 block net sda5 tty3 tty60 ttyS4 bsg network_latency sda6 tty30 tty61 ttyS5 btrfs-control network_throughput serial tty31 tty62 ttyS6 bus null sg0 tty32 tty63 ttyS7 char oldmem shm tty33 tty7 ttyS8 console parport0 snapshot tty34 tty8 ttyS9 core port snd tty35 tty9 ttyUSB0 cpu ppp stderr tty36 ttyprintk ttyUSB1 cpu_dma_latency psaux stdin tty37 ttyS0 uinput disk ptmx stdout tty38 ttyS1 urandom dri pts tty tty39 ttyS10 usbmon0 ecryptfs ram0 tty0 tty4 ttyS11 usbmon1 fb0 ram1 tty1 tty40 ttyS12 usbmon2 fd ram10 tty10 tty41 ttyS13 vcs full ram11 tty11 tty42 ttyS14 vcs1 fuse ram12 tty12 tty43 ttyS15 vcs2 hidraw0 ram13 tty13 tty44 ttyS16 vcs3 hpet ram14 tty14 tty45 ttyS17 vcs4 input ram15 tty15 tty46 ttyS18 vcs5 kmsg ram2 tty16 tty47 ttyS19 vcs6 log ram3 tty17 tty48 ttyS2 vcsa loop0 ram4 tty18 tty49 ttyS20 vcsa1 loop1 ram5 tty19 tty5 ttyS21 vcsa2 loop2 ram6 tty2 tty50 ttyS22 vcsa3 loop3 ram7 tty20 tty51 ttyS23 vcsa4 loop4 ram8 tty21 tty52 ttyS24 vcsa5 loop5 ram9 tty22 tty53 ttyS25 vcsa6 loop6 random tty23 tty54 ttyS26 vga_arbiter loop7 rfkill tty24 tty55 ttyS27 zero lp0 rtc tty25 tty56 ttyS28 mapper rtc0 tty26 tty57 ttyS29 mcelog sda tty27 tty58 ttyS3

  Read the article

• Wireless connection disconnects and reconnects with a Netgear WNA1000

  - by William Berkenkamp

  Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >