Search Results

Search found 41338 results on 1654 pages for 'used'.

Page 310/1654 | < Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >

• Ubuntu: Memory Leak

  - by Keener

  I'm having trouble finding from where this memory leak is occurring. I'm running Ubuntu 8.04 LTS on a Dell XPS M1530. I have 3GB of ram and I'm finding after about an hour or so of use top shows me 2GBs+ used. The strange thing is when I add up the memory percentages by PID either from top or ps aux I find that I should only be using about 20-25% of my available ram. What brought this to my attention was I've begun running vmware server again. Now, obviously the ram usage spikes when I load a virtual machine, but the memory VMware is using does not account for the memory usage I'm seeing via top or free. Stopping vmware server releases the memory which was allocated to it, but I'm still unable to find where this RAM is being used. After a complete reboot, of course, the memory is fine, but very quickly it climbs to 60-80% usage with the processes only appearing to account for a third of that. Any ideas where I should look for more information on what this could be?

  Read the article

• Setting up ssh config file with id_rsa through tunnel

  - by Rubens

  I've been struggling to set up a valid configuration to open a connection with a second machine, passing through another one, and using an id_rsa (which requests me a password) to connect to the third machine. I've asked this question in another forum, but I've received no answer that could be considered very helpful. The problem, better described, goes as follows: Local machine: user1@localhost Intermediary machine: user1@inter Remote target: user2@final I'm able to do the entire connection using pseudo-tty: ssh -t inter ssh user2@final (this will ask me the password for the id_rsa file I have in machine "inter") However, for speeding things up, I'd like to set my .ssh/config file, so that I can simply connect to machine "final" using: ssh final What I've got so far -- which does not work -- is, in my .ssh/config file: Host inter User user1 HostName inter.com IdentityFile ~/.ssh/id_rsa Host final User user2 HostName final.com IdentityFile ~/.ssh/id_rsa_2 ProxyCommand ssh inter nc %h %p The id_rsa file is used to connect to the middle machine (this requires me no password typing), and id_rsa_2 file is used to connect to machine "final" (this one requests a password). I've tried mixing up some LocalForward and/or RemoteForward fields, and putting the id_rsa files in both first and second machines, but I could not seem to succeed with no configuration whatsoever. Hope somebody can help me here! Regards! P.S.: the thread I've tried to get some help from: http://www.linuxquestions.org/questions/linux-general-1/proxycommand-on-ssh-config-file-4175433750/

  Read the article

• i7-980X at 70% speed

  - by Buxley

  Hi we bought a nice computer to use to solve optimization problems. Intel i7-980X@3,33 GHz with 12 GB of Team Group 1600 MHz DDR3 RAM. When we use Gurobi the computer uses all 12 cores at maximum in the beginning of the solve. However after a while (about 8 hrs) it all cores jump between 65 and 85% When I solve the same models on an i7 930 all cores are at a near 100% level even after longer solution times. We first thought that the Hard disk was the bottleneck since Gurobi writes out nodefiles after the memorylimit is used. However since the new computer have 12 GB of RAM we put the memorylimit to 7 GB so the solver only used the RAM and still with the same performance in the processor. Any ideas about the bottleneck? As I said earlier it works at 100% for the first hours or so . Thanks very much for any answers! Our plan was to overclock it but we can't even get it to work at normal speed yet!

  Read the article

• How do you set up CRON?

  - by user1723760

  I have never used CRON before but I want to use CRON in order to be able to perform schedule jobs for a php script. The php script is called "inactivesession.php" and in the php script is this code: <?php include('connect.php'); $createDate = mktime(0,0,0,10,25,date("Y")); $selectedDate = date('d-m-Y', ($createDate)); $sql = "UPDATE Session SET Active = ? WHERE DATE_FORMAT(SessionDate,'%Y-%m-%d' ) <= ?"; $update = $mysqli->prepare($sql); $update->bind_param("is", 0, $selectedDate); $update->execute(); ?> Wht I want to do is that when the above date is reached (25th Oct), I want the php script to perform the UPDATE statement above. But my question is that how do I use CRON in order to do this? The server I am using is the university's server known as helios, does CRON need to be set up in helios, (do I have to call the admin for this) or is it something else which uses CRON. I have never used CRON before so can you explain to me how CRON can be set up for the example above with the server I am using? Thanks UPDATE: Hi, I think the name of the OS is actually helios but I am not sure, I have a wikipedia page on this: here. I will read the crontab wikipedia page and see what I can find, but what my question is that is CRON already set up, do I just go right ahead and use CRON or do I need to set it up first?

  Read the article

• i7 x980 at 70% speed

  - by Buxley

  Hi we bought a nice computer to use to solve optimization problems. intel i7 X980@3,33 Mhz with 12 Gb of Team Group 1600 MHz ddr3 Ram. When we use Gurobi The Computer uses all 12 cores at maximum in the beginning of the solve. However after a while (about 8 hrs) it all cores jump between 65 and 85% When I solve the same models on an I7 930 all cores are at a near 100% level even after longer solution times. we first thought that the Harddisk was the bottleneck since Gurobi writes out nodefiles after the memorylimit is used. However since the new computer have 12 GB of Ram we put the memorylimit to 7 GB so the solver only used the RAM and still with the same performance in the processor. Any Ideas about the bottleneck? As I said earlier it works at 100% for the first hours or so . Thanks very much for any answers! Our plan was to overclock it but we can't even get it to work at normal speed yet!

  Read the article

• The BitLocker encrypted logical drive of my laptop is not accessible. On clicking error appears,"Application not found"

  - by Nauman Khan

  I had an important personal data that was stored in my laptop drive 'F'. My 4 year old son also uses my laptop to play games. To secure my data I used bitlocker software that was already there in my windows 7 ultimate 32 bit. I am using a Dell D 630 Core2Duo laptop. The thing worked fine for me and I have been able to access my data in drive 'F' as and when I required. But today, when I tried to open my 'F' drive, an error box appeared saying "Application not found". I right clicked and checked 'properties' of 'F' drive. It showed me Used Space = 0 bytes and Free Space = 0 bytes. I opened 'Disk Management' which showed my 'F' drive file system as 'Unknown (Bitlocker Encrypted). 'Disk Management' is also showing my 'F' drive as healthy logical drive. I opened 'Manage bitlocker' and found that my 'F' drive was being shown locked and 'Unlock Drive' was displayed against it, however, when i click on 'Unlock Drive', it does not function. I opened 'TPM Administration' and found an information that 'Compatible TPM cannot be found'. My bitlocker encryption was working fine which means that I had a compatible TPM in my laptop. Where has it gone? How can I enable it? Is my 'F' Drive lost forever and thus the data in there as well?

  Read the article

• disk space keeps filling up on EC2 instance with no apperent files/directories

  - by sasher

  How come os shows 6.5G used but I see only 3.6G in files/directories? Running as root on an Amazon Linux AMI (seems like Centos), lots of free memory available, no swapping going on, no apparent file descriptors issue. The only thing I can think of is a log file that was deleted while applications append to it. Disk space usage is slowly but continuously rising towards full capacity (~1k/min with very small decreases from time to time) Any explanation? Solution? du --max-depth=1 -h / 1.2G /usr 4.0K /cgroup 22M /lib64 11M /sbin 19M /etc 52K /dev 2.1G /var 4.0K /media 0 /sys 4.0K /selinux du: cannot access /proc/14024/task/14024/fd/4': No such file or directory du: cannot access<br/> /proc/14024/task/14024/fdinfo/4': No such file or directory du: cannot access /proc/14024/fd/4': No such file or directory du: cannot<br/> access/proc/14024/fdinfo/4': No such file or directory 0 /proc 18M /home 4.0K /logs 8.1M /bin 16K /lost+found 12M /tmp 4.0K /srv 35M /boot 79M /lib 56K /root 67M /opt 4.0K /local 4.0K /mnt 3.6G / df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.5G 1.4G 84% / tmpfs 3.7G 0 3.7G 0% /dev/shm sysctl fs.file-nr fs.file-nr = 864 0 761182

  Read the article

• From a performance standpoint, is there a preferred way to set up Thunderbird message filters?

  - by Steve V.

  When I used Kontact, I used filters heavily to sort my incoming email into various folders. Since switching to Thunderbird, I've been slowly recreating these filters as new mail arrives. This seems like the perfect time to rethink how I use message filters. The way I see it, there are two basic ways to filter messages. Either I can have lots of filters, or I can have lots of criteria. An example is in order. Assume that I get emails from four people (Boss, CEO, Intern, and StackOverflow) that I want to sort into two folders, "Stack" and "Work" Option A: Filter 1: if FROM contains "Boss" -> move to "Work" Filter 2: if FROM contains "CEO" -> move to "Work" Filter 3: if FROM contains "Intern" -> move to "Work" Filter 4: if FROM contains "StackOverflow" -> move to "Stack" Option B: Filter 1: if FROM contains "Boss" OR FROM contains "CEO" OR FROM contains "Intern" -> move to "Work" Filter 2: if FROM contains "StackOverflow" -> move to "Stack" Assuming that when I'm done, I'll have about a hundred different criteria to filter on, is one of these methods better than the other from a performance standpoint?

  Read the article

• WIN7 constant BSOD 0x7B on boot, not producing any dump files where to go from here?

  - by prayingpantis

  So my one win 7 pc has been getting a BSOD on boot (roughly a sec after load screen starts) after a power failure. The complete stop code is 0x0000007B (0x80786B58, 0xC0000034,0x00000000,0x00000000) I've searched for quite a while now on the net and it seems like most people gave up after gettting 0x7B and no dump files. What I've tried so far: startup repair - reports it cannot repair computer automatically. BadPatch is reported somewhere in a problem signature contained in the problem details. startup repair with a WIN 7 CD - also fails, I can't recall what the error was, but it was not the same as the error produced with the start up tool shipped with the version of WIN 7 installed on my machine (I think the text had something ACL-ish contained in it) used a boot disk (Hiren's boot iso) - I used it to enable the CrashDump registry key and then after BSOD, read the HDD's dump locations but it was empty. Note, I'm quite sure the registry keys I edited are the correct ones, since the reboot on BSOD option was enabled by default and after I changed the regkey controlling this functionalitty to 0 the BSOD stayed after I booted again. check disk - works and returns no problems, also it seems I'm able to access all my files on the HDD. mem test - works and returns no errors So I'm not sure what else I can do to figure out what is the problem here. I read somewhere that you can use WINDBG to remote debug another PC, but I'm not sure if this is possible since the OS isn't even loaded yet? Also the last driver change I made on the system was installing a video driver, but I had no problems with it and were able to reboot several times until the power outage happened and the BSOD appeared. Any help or guidance for a way to DEBUG this problem would really be appreciated (I'm not really that keen to try a whole bunch of random fixes, I'd rather try and narrow down the problem first).

  Read the article

• disk partition centos

  - by FlourishDNA

  I am setting up server for hosting two WordPress which has size of around 70GB. I have already installed CentOS as OS and I would like to partition the Disk. Is there any tool which can help me or can someone guide me though the process as I am not expert is SSH commands. Here are some output that might help. OS: CentOS release 6.3 fdisk -l Disk /dev/xvdb: 214.7 GB, 214748364800 bytes 255 heads, 63 sectors/track, 26108 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b91e0 Device Boot Start End Blocks Id System Disk /dev/xvda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e542c Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/vg_flourish-lv_root: 16.7 GB, 16718495744 bytes 255 heads, 63 sectors/track, 2032 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_flourish-lv_swap: 4227 MB, 4227858432 bytes 255 heads, 63 sectors/track, 514 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 df Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_flourish-lv_root 16070076 758184 14495560 5% / tmpfs 958500 0 958500 0% /dev/shm /dev/xvda1 495844 31926 438318 7% /boot df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_flourish-lv_root 16G 741M 14G 5% / tmpfs 937M 0 937M 0% /dev/shm /dev/xvda1 485M 32M 429M 7% /boot Thanks

  Read the article

• Apache: getting proxy, rewrite, and SSL to play nice

  - by Rich M

  Hi, I'm having loads of trouble trying to integrate proxy, rewrite, and SSL altogether in Apache 2. A brief history, my application runs on port 8080 and before adding SSL, I used proxy to strip the 8080 from the url's to and from the server. So instead of www.example.com:8080/myapp, the client app accessed everything via www.example.com/myapp Here was the conf the accomplished this: ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> ProxyPass /myapp http://www.example.com:8080/myapp ProxyPassReverse /myapp http://www.example.com:8080/myapp What I'm trying to do now is force all requests to myapp to be HTTPS, and then have those SSL requests follow the same proxy rules that strip out the port number as my application used to. Simply changing the ports 8080 to 8443 in the ProxyPass lines does not accomplish this. Unfortunately I'm not an expert in Apache, and my skills of trial and error are already reaching the end of the line. RewriteEngine On RewriteCond %{HTTPS} off RewriteRule myapp/* https://%{HTTP_HOST}%{REQUEST_URI} ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> SSLProxyEngine on ProxyPass /myapp https://www.example.com:8443/mloyalty ProxyPassReverse /myapp https://www.example.com:8433/mloyalty As this stands, a request to anything on the server other than /myapp load fine with http. If I make a browser http request to /mypp it then redirects to https:// www.example.com:8443/myapp , which is not the desired behavior. Links within the application then resolve to https:// www.example.com/myapp/linkedPage , which is desirable. Browser requests (http and https) to anything one level beyond just /myapp ie. /myapp/mycontext resolve to https:// www.example.com/myapp/mycontext without the port. I'm not sure what other information there is for me to give, but I think my goals should be clear.

  Read the article

• centos install / partitioning

  - by ServerSideX

  I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

  Read the article

• iptables: How to combine DNAT and SNAT to use a secondary IP address?

  - by Que_273

  There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

  Read the article

• Hibernation fails; The system cannot find the file specified

  - by GMMan

  Recently I installed Ubuntu 12.04.1 LTS on my Lenovo Y480. Hibernation was working properly after the Ubuntu install, but I was making sure all of the operating systems on my system worked, including OneKey Recovery (recovery partition). It is of note that I installed Windows 7 from scratch with a disk image I downloaded off of my university's DreamSpark program, and further to that I had to image the partition with Paragon Backup & Recovery, repartition to convert the Windows partition to extended, install Ubuntu, and then restore the image. During that process I also used the Windows disc to edit the BCD as to reuse the existing entry for the restored partition. I also used the automated "repair your computer" option. With verification, I noticed that the "repair your computer" option actually wrote to the wrong BCD (the recovery partition), and I mounted the partition and restored the original BCD (from a copy I made earlier), and rebooted. At this point my GRUB broke, and I was able to restore it. At this point hibernation broke. I tried powercfg /h off and powercfg /h on, rebooted, and nothing. Also tried increasing the hibernation file size as directed on this post, but it still doesn't work. Executing shutdown /h yields The system cannot find the file specified.(2). What file? It seems that mounting the system partition sometimes works, but I don't want to keep it mounted in case it gets written to accidentally. How do I permanently fix this?

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Rendering a frame is producing noise from speakers in Windows and Linux

  - by Robber

  When any hardware accelerated application is rendering a frame (or many of them) a very short noise is coming from my speakers. This can be a game, a WebGL application or XBMC. When the application/game is rendering many frames per second (like most of them do) the noise is a continuous buzzing that gets higher pitched with higher framerates. This applies to Linux and Windows, so I'd assume it's a hardware problem. The current hardware in the PC is: CPU: Core2Quad Q9550 GPU: Radeon HD 5770 RAM: 2x2GB DDR2 Motherboard: Asus P5QLD PRO PSU: be quiet! Pure Power 530W Screen and speakers: Old 720p LCD TV connected via VGA and aux cable Muting the TV stops the noise, muting Windows doesn't. I tried replacing the PSU first (used a Tagan 700W PSU before) because I thought it was a power problem. It wasn't. I tried replacing the motherboard (used a ASUS P5B SE before) next because I thought it was a sound card problem. It wasn't. I tried the GPU in a different PC because I thought it was a broken graphics card. It worked perfectly fine in the other PC. I thought it might be interference, but moving the audio cable around changes absolutely nothing. I tried using an HDMI cable instead and that did work, but is not an option since my TV has only one HDMI input and I need that for my PS3.

  Read the article

• Mail Server using Postfix

  - by unknown (google)

  I have currently set up my web application on Amazon EC2 server. As a well known fact sending email from EC2 has a problem. As a cheap and long lasting solution instead of using "authsmtp" is it possible to rent a server and use it as a Mail Server? I am currently looking for cheap hosting which will give me root access so that it can be configured and used as a relayhost. I am curently using Postfix as MTA. Has any one implemented this before? I am curious about its feasibility of this solution. I guess common requirements are: 1: Dedicated IP which is not black listed. 2: Open relay( open to my Server only) Any Tips for Header configurations to keep the mails out of spam folder. This is like exactly cloning authsmtp for personal use. Any suggestions for other Mail Server software instead of Postfix? Another problem is Reverse DNS for this server. Should PTR entry be present if a server is used as a relayhost?

  Read the article

• Can I configure Thunderbird 3 to refresh the folder list for an Exchange IMAP account?

  - by Howiecamp

  Background: When used as an IMAP client against Gmail, Thunderbird 3 (may be the case in v2 also, not sure) will refresh it's list of folders (the folders correspond to Gmail labels) when you do "Download/Sync Now..." or restart the Thunderbird client. Any new folders (labels) created in Gmail will sync to the client and any folders moved/changed/deleted folders in Gmail will move/change/delete on the client as well. (Note: Thunderbird has the concept of "subscribing" to IMAP folders (assumingly allowing you to determine which folders you want, rather than bringing all of them down and dragging loads of data across the wire). When used against Gmail, Thunderbird appears to automatically subscribe to all folders (including when folders are newly created in Gmail), so this might be why the refresh is happening properly.) This behavior is what I want with Exchange. When using Thunderbird with Exchange (2007), the folder list doesn't refresh when folders are added/changed/deleted on the server and/or from a different mail client. When I look at the subscription options, some are checked and some are not (not sure why Thunderbird picked some and not others). And when I add new folders on the server and/or from another client, they never even appear in Thunderbird's list of folders, preventing me from subscribing to them.

  Read the article

• Diagnosing RAM issues

  - by TaylorND

  I have an old Acer Aspire T180 desktop. The specs are as follows: AMD Athlon 64 3800+ 2.4GHz 1GB DDR2 SDRAM 160GB DVD-Writer (DVD±R/±RW) Gigabit Ethernet 17" Active Matrix TFT Color LCD Windows Vista Home Basic Mini-tower AST180-UA381B According to the information in the computer's documentation the computer comes with 1 GB of RAM. It has two DDR2 SDRAM sticks. I used to have Windows Vista installed. Then I removed it and install Windows 7, and now I have since removed Windows 7 and installed Windows XP. According to Windows XP with both RAM sticks in the computer has 768 MB. Isn't this supposed to be 1 GB of RAM or 1024 MB of RAM? Is the amount of RAM installed only partly used by the Operating System? Is there's something I'm missing? If I remove either one of the RAM sticks I'm left with 448 MB of RAM. These numbers don't seem to add up. If each of the RAM sticks contains at least 448 MB of RAM shouldn't they (both being in) provide 896 MB of RAM. Even then, isn't that less than a GB of RAM? I'm not too experienced in hardware so I thought this would be the best place to ask. As a follow up question, is the RAM I have enough to run/multitask with Windows XP efficiently? I plan to do a lot of computing with the system (although not gaming), should I invest in more RAM?

  Read the article

• What is best configuration settings for Wordpress and MySQL on Win2008 + IIS7 stack?

  - by holiveira

  I currently have four blogs that uses Wordpress running on a shared hosting company. This blogs have a considerable amount of visits and I'm constantly receiving warnings from the hosting company saying that I'm consuming too much server CPU. Considering the fact that I have a dedicated server in another company with plenty of idle resources (it has a quad core Xeon 2.5GHz and 8GB of Ram and run on Win2008) I'm planning to move the blogs to this server in order to have some more freedom. I'm currently using this server to host some web applications using ASP.Net and SQL Express. I've installed a blog to test and it worked fine, but some issues appeared and raised some questions in my mind: How to properly set the permissions in the folders used by wordpress plugins, I mean, what permissions should I set for the IIS_User in some folders so that the plugins works correctly? What's the best caching plugin to use considering this is a Window Server? In the previous hosting company I used the WPSuperCache, but it was a Linux Stack. Or should I ignore the caching plugins and use the Dynamic Caching Feature of IIS7? How can I optmize the MySQL server running in this server (specially the settings regarding memory and caching) How can I protect the admin folders against hacker attacks? I know some people will advice me not to run Wordpress in a Windows stack, but that's my only choice. I don't even know were to start managing and LAMP stack, don't have the time to do so nor the money to rent another server.

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

• Synchronizing the SamAccountName Property using Windows Azure Active Directory Sync Tool

  - by pk.

  Using this official documentation as a guide, I would expect the SamAccountName property to sync from my on-premise AD to Office 365. I think that it used to do exactly that, but now it seems that it doesn't so much sync the attribute as it does create an entirely new, unlinked value and store it in Office 365. This has caused some minor issues for me (broken scripts, annoying permissions management, etc.) and may be part of a more major issue regarding ADFS authentication. On-Premise PS C:\Windows\system32> Get-ADUser jdoe -Properties SamAccountName | fl SamAccountName SamAccountName : jdoe Office 365 Sync'ed Objects PS C:\Windows\system32> Get-Mailbox jdoe | fl SamAccountName SamAccountName : $1A7H20-K1LCOJFFBHGS I understand how to work around this issue in my scripts -- there exists the ImmutableId property which can be mapped back to the on-premise GUID. As far as the issue I'm having with ADFS, I'm less certain how to proceed and if this is causing my issues. At this point I really would just like some verification that I'm not crazy and that this used to be sync'ed at some point in the past and that Office 365 broke it relatively recently. I also think that MS documentation should perhaps be updated to exclude SamAccountName from the list of synchronized properties on the page I linked.

  Read the article

• Outbound ports to allow through firewall - core requirements

  - by dunxd

  This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support email and web access, which I know everyone will need: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working? I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

  Read the article

• How to backup virtual machines on a standalone ESXi host?

  - by Massimo

  Standalone ESXi (4.1) host without any vCenter Server. How to backup virtual machines as quickly and storage-friendly as possible? I know I can access the ESXi console and use the standard Unix cp command, but this has the downfall of copying the whole VMDK files, not only their actually used space; so, for a 30-GB VMDK of which only 1 GB is used, the backup would take 30 full GBs of space, and time accordingly. And yes, I know about thin-provisioned virtual disks, but they tend to behave very badly when physically copied, and/or to blow up to their full provisioned size; also, they are not recommended for actual VM performance. It is ok for me to shut down the VMs before backing them up (i.e. I don't need "live" backups); but I need a way to copy them around efficiently; and yes, a way to automate shutdown/startup when taking a backup would also help. I only have ESXi; no Service Console, no vCenter Server... what's the best way to handle this task? Also, what about restores?

  Read the article

• Input/output error reading USB backup drive on CentOS 6.4

  - by Kev

  I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

  Read the article

< Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >